Chungear Co CE10709 Ceiling Fan Remote Controller (Transmitter) User Manual

Chungear Industrial Co Ltd Ceiling Fan Remote Controller (Transmitter)

User Manual

CEILING FAN REMOTE CONTROLLEROPERATION AND INSTALLATION INSTRUCTIONS(Please keep this instruction pamphlet.)IMPORTANT POINTS TO REMEMBER:1.Read and save these instructions.2.Please note that all fixed wiring appliances should be installed by a qualified electrician.3.The supply to the remote control receiver should be connected through a main switch, i.e. existing wallswitch.4.Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.5.Install receiver into the ceiling fan canopy of the fan to ensure proper protection.6.This unit is to be used for the control of ceiling fan and in a AC230/240V 50Hz power supply only.7.Do not install in damp locations or immerse into water. (For indoor use only.)8.Do not pull on or cut leads shorter.9.Do not drop or bump the unit.10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place asthis will damage the transmitter. Dispose of used battery properly and keep the battery out of reach ofchildren.11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable(rheostat) wall control.INSTALLATION INSTRUCTIONS1.Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pulling the “Pull Switch”after installation.2.Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopycomes up to cover the receiver and bracket.IMPORTANTYOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEEDAND LIGHT KIT (IF ANY) TO BE ON POSITION BEFORE OPERATINGREMOTE CONTROL.CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
CODE SWITCH1.CODE SWITCH: Codes are set by pushing dip switches up or down. It is imperative that the code usedfor both transmitter and receiver is exactly the same; otherwise remote controller will not work. Pleasenote the code switch will enable you to operate a second remote controller independently. For example, ifyou have two ceiling fans with 2 remote control units, set 2 different codes for each set oftransmitter/receivers. This means you can operate each ceiling fan independently.2.Your remote control is ready for use after battery installation.FUNCTIONS OF TRANSMITTEROFF : Turn off the ceiling fan.HI : Turn on the fan at high speedMED : Turn on the fan at medium speedLOW : Turn on the fan at low speedLIGHT : ON/OFF : Press and release immediately to turn onor off the lightDIMMER : Press and hold on to dim or brightenlights to the desired level and release.(Only for the tungsten bulb.)Ceiling Fan Remote ControlWiring ConnectionTRANSMITTERInstallation oftransmitter wall mountholder with two screws.TR313A
To assure continued FCC compliance:FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouragedto try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connectthe equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer oran experienced radio/TV technician for help.CAUTION:To assure continued FCC compliance:Any changes or modifications not expressly approved by the grantee of this device could void the user's authority tooperate the equipment.FCC ID：KUJCE10709This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.IC：10786A-TR313AThis device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following twoconditions: (1) this device may not cause interference, and (2) this device must accept any interference, includinginterference that may cause undesired operation of the device.French:Cet appareil radio est conforme au CNR d’Industrie Canada. L’utilisation de ce dispositif estautorisée seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2)l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si cebrouillage est susceptible de compromettre le fonctionnement du dispositif.

Navigation menu