CipherLab A1010 Bluetooth Cradle User Manual A1010 manual
CipherLab Co., Ltd. Bluetooth Cradle A1010 manual
Users manual
A1010 Cradle
User’s Manual
WARNING
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
If applicable, as below
FCC Caution: To assure continued compliance, (example – use only shielded
interface cables when connecting to computer or peripheral devices). Any changes
or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator & your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Table of Contents
1. INTRODUCTION.............................................................…………………..0
2. CRADLE INSTALLATION..........................................................................1
2.1 POWER UP THE CRADLE BASE STATION ....................................................2
2.4 CHARGING CIPHERLAB 1166/1266 ........................................................2
2.4.1 Scanner .............................................................................................3
2.4.2 Battery...............................................................................................3
2.4.3 DC Jack.............................................................................................4
6.3 CONFIGURING BLUETOOTH DEVICE DRIVER..............................................4
6.3.1 Windows XP with Service Pack2.......................................................4
6.3.2 Widcomm Bluetooth Driver ..............................................................7
1. Introduction
A1010 is special cradle that it is a Bluetooth Dongle with Charger of
CIPHERLAB Bluetooth Barcode Scanner 1166/1266. Cradle function show
below.
1. USB 2.0 Bluetooth Dongle
2. Charger for CIPHERLAB Bluetooth Barcode Scanner 1166/1266
3. Charger for battery pack of CIPHERLAB Bluetooth Barcode Scanner
1166/1266
2
2. Cradle Installation
The kit contains:
A cradle dongle base
A rechargeable battery
A USB Cable
A power supply
Diskette containing “Scan Manager” and this manual
2.1 Power Up the Cradle Base Station
Connect the interface cable into the USB connector at the back of the base.
Power off your PC or Laptop when connect the cable to PC or Laptop. Once your
cable is connected to the base, plug the other end into the appropriate port on your
PC.
Connect the power supply provided to your AC outlet and plug the other end into
the base then power on your PC.
Now you are ready to configure your scanner and base.
2.2 Charging CIPHERLAB Bluetooth Barcode Scanner
1166/1266
There are three methods to charge the battery. One is placing the scanner on the
base and another is inserting the battery in front of the base, and the other is
inserting the power supply into the DC Jack at bottom of the scanner.
2.2.1 Scanner
Place the scanner with a battery inserted on the base to charge your scanner. When
charging, the scanner LED will flash RED. When the battery is fully charged,
around 4 hours from completely empty battery, the LED stays on solid RED. If the
battery is out of power, the LED is off.
2.2.2 Battery
Insert the battery in front of the base to charge your battery with the power adaptor
connected. When charging, the base charging LED will be RED. When the battery
is fully charged, around 4 hours from completely empty battery, the LED will be
solid GREEN.
4
2.2.3 DC Jack
Insert the power supply to the DC Jack at bottom of the scanner. When charging,
the scanner LED will flash RED. When the battery is fully charged, around 4 hours
from completely empty battery, the LED stays on solid RED.
2.3 Configuring Bluetooth Device Driver
Please follow the procedures below to configure the Bluetooth driver on the host
system. Please note that, when searching nearby Bluetooth devices on Host
computers, the 1x66 scanner will come out with the serial number as their device
name. Please check the serial number label on the scanner when making
connections.
2.3.1 Windows XP with Service Pack2
1. Insert the Bluetooth dongle into PC host.
2. Double click the Bluetooth icon on the lower right of the taskbar.
3. Click Add button.
1. Check My device is set up and ready to be found and click Next button.
2. Select the 1x66 scanner and click Next button.
3. Select Let me choose my own passkey and input the passkey in the text field
and click Next button.
6
4. When the connection is ready, a message will be displayed : Found New
Hardware Bluetooth HID Device. Please click Finish button to complete the
connection.
8. The scanner is ready to use. Please click OK button.
2.3.2 Widcomm Bluetooth Driver
1. Click icon at PC.
2. Click Find Bluetooth Devices icon at My Bluetooth Places.
3. Right click the 1x66 scanner and select Pair Device.
4. Input PIN code and click OK button.
8
5. Right click 1x66 scanner and select Discover Available Services.
6. Click PC Remote Commander icon.
7. Click Yes Button.
No
8. When the green arrow icon is displayed, the connection is ready.