Cisco Systems 102054E 802.11a/b/g access point User Manual ap1130b

Cisco Systems Inc 802.11a/b/g access point ap1130b

manual

CISCO CONFIDENTIAL - Draft 2Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-4100Cisco Aironet 1130AG Series Access Point Hardware Installation Guide November 2004Customer Order Number: Text Part Number: OL-6226-01
CISCO CONFIDENTIAL - Draft 2THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:• Turn the television or radio antenna until the interference stops.• Move the equipment to one side or the other of the television or radio.• Move the equipment farther away from the television or radio.• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.) Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.Cisco Aironet 1130AG Series Access Point Hardware Installation GuideCopyright © 2004 Cisco Systems, Inc. All rights reserved.CCSP, the Cisco Square Bridge logo, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, Registrar, ScriptShare, SlideCast, SMARTnet, StrataView Plus, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0406R)
CISCO CONFIDENTIAL - Draft 2iiiCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01CONTENTSPreface ixAudience ixPurpose ixOrganization ixConventions xRelated Publications xiiObtaining Documentation xiiCisco.com xiiDocumentation CD-ROM xiiiOrdering Documentation xiiiDocumentation Feedback xiiiObtaining Technical Assistance xivCisco.com xivTechnical Assistance Center xivLocating the Product Serial Number xvCisco TAC Website xvCisco TAC Escalation Center xviObtaining Additional Publications and Information xviOverview 1-1Hardware Features 1-2Dual-Radio Operation 1-2Ethernet Port 1-3Console Port 1-3LEDs 1-3Power Sources 1-4Anti-Theft Features 1-4UL 2043 Certification 1-6Network Configuration Examples 1-6Root Unit on a Wired LAN 1-6Repeater Unit that Extends Wireless Range 1-8Central Unit in an All-Wireless Network 1-9
CISCO CONFIDENTIAL - Draft 2ContentsivCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Installing the Access Point 2-1Safety Information 2-2FCC Safety Compliance Statement 2-2General Safety Guidelines 2-2Warnings 2-2Unpacking the Access Point 2-3Package Contents 2-3Basic Installation Guidelines 2-3Before Beginning the Installation 2-4Access Point Layout and Connectors 2-4Mounting Plate 2-5Suspended Ceiling Adjustable T-Rail Clips 2-6Installation Summary 2-7Opening the Access Point Cover 2-8Mounting the Access Point 2-9Mounting on a Horizontal or Vertical Surface 2-10Mounting Below a Suspended Ceiling 2-11Mounting Above a Suspended Ceiling 2-13Mounting on a Network Cable Box 2-14Mounting on a Desktop or Shelf 2-15Rotating the Cisco Logo 2-15Attaching the Access Point to the Mounting Plate 2-16Connecting the Ethernet and Power Cables 2-17Connecting to an Ethernet Network with an Inline Power Source 2-18Connecting to an Ethernet Network with Local Power 2-19Securing the Access Point 2-19Using a Security Cable 2-19Securing the Access Point to the Mounting Plate 2-20Powering Up the Access Point 2-21Configuring the Access Point for the First Time 3-1Before You Start 3-2Resetting the Access Point to Default Settings 3-2Using the Mode Button 3-2Using the Web-Browser Interface 3-2Obtaining and Assigning an IP Address 3-3Connecting to the Access Point Locally 3-3Assigning Basic Settings 3-4
CISCO CONFIDENTIAL - Draft 2ContentsvCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Default Settings on the Express Setup Page 3-8Protecting Your Wireless LAN 3-9Using the IP Setup Utility 3-9Obtaining and Installing IPSU 3-9Using IPSU to Find the Access Point’s IP Address 3-10Assigning an IP Address Using the CLI 3-11Using a Telnet Session to Access the CLI 3-11Using the Web-Browser Interface 4-1Using the Web-Browser Interface for the First Time 4-2Using the Management Pages in the Web-Browser Interface 4-2Using Action Buttons 4-4Character Restrictions in Entry Fields 4-5Using Online Help 4-5Using the Command-Line Interface 5-1Cisco IOS Command Modes 5-2Getting Help 5-3Abbreviating Commands 5-3Using no and default Forms of Commands 5-3Understanding CLI Messages 5-4Using Command History 5-4Changing the Command History Buffer Size 5-4Recalling Commands 5-5Disabling the Command History Feature 5-5Using Editing Features 5-5Enabling and Disabling Editing Features 5-6Editing Commands Through Keystrokes 5-6Editing Command Lines that Wrap 5-7Searching and Filtering Output of show and more Commands 5-8Accessing the CLI 5-8Opening the CLI with Telnet 5-8Opening the CLI with Secure Shell 5-9
CISCO CONFIDENTIAL - Draft 2ContentsviCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Troubleshooting 6-1Checking the Access Point LEDs 6-2Checking Basic Settings 6-4SSID 6-4WEP Keys 6-5Security Settings 6-5Low Power Condition 6-5CDP Inline Power Negotiation 6-6Inline Power Status Messages 6-6Inline Power Exception 6-7Issuing the Cisco IOS Command 6-7Running the Carrier Busy Test 6-8Running the Ping/Link Test 6-8Resetting to the Default Configuration 6-9Using the MODE Button 6-9Using the Web Browser Interface 6-10Reloading the Access Point Image 6-10Using the MODE Button 6-11Web Browser Interface 6-12Browser HTTP Interface 6-12Browser TFTP Interface 6-12Obtaining the Access Point Image File 6-13Obtaining the TFTP Server Software 6-13Translated Safety Warnings A-1Statement 245B—Explosive Device Proximity Warning A-2Statement 332—Antenna Installation Warning A-3Statement 1001—Work During Lightning Activity Warning A-4Statement 1004—Installation Instructions Warning A-5Statement 1005—Circuit Breaker (15A) Warning A-6Declarations of Conformity and Regulatory Information B-1Manufacturers Federal Communication Commission Declaration of Conformity Statement B-2Department of Communications—Canada B-3Canadian Compliance Statement B-3European Community, Switzerland, Norway, Iceland, and Liechtenstein B-3Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC B-3Declaration of Conformity for RF Exposure B-5
CISCO CONFIDENTIAL - Draft 2ContentsviiCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Guidelines for Operating Cisco Aironet Access Points in Japan B-6Japanese Translation B-6English Translation B-6Declaration of Conformity Statements B-7Access Point Specifications C-1Channels and Power Levels D-1Channels and Maximum Power Levels D-2IEEE 802.11b/g (2.4-GHz Band) D-2IEEE 802.11a (5-GHz Band) D-3Console Cable Pinouts E-1Overview E-2Console Port Signals and Pinouts E-2GLOSSARYINDEX
CISCO CONFIDENTIAL - Draft 2ContentsviiiCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01
CISCO CONFIDENTIAL - Draft 2ixCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01PrefaceAudienceThis guide is for the networking professional who installs and manages the Cisco Aironet 1130AG Series Access Point, hereafter referred to as the access point. To use this guide, you should have experience working with the Cisco IOS software and be familiar with the concepts and terminology of wireless local area networks.PurposeThis guide provides the information you need to install and configure basic settings for your access point. For information on using Cisco IOS commands to configure your access point, refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points. For detailed information about these IOS commands, refer to the Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges for this release. For information about the standard IOS Release 12.2 commands, refer to the IOS documentation set available from the Cisco.com home page at Service and Support > Technical Documents. On the Cisco Product Documentation home page, select Release 12.2 from the Cisco IOS Software drop-down menu.This guide also includes an overview of the access point web-based interface (APWI), which contains all the functionary of the command-line interface (CLI). This guide does not provide field-level descriptions of the APWI windows nor does it provide the procedures for configuring the access point from the APWI. For all APWI window descriptions and procedures, refer to the access point online help, which is available from the Help buttons on the APWI pages.OrganizationThis guide is organized into these chapters:Chapter 1, “Overview,” lists the software and hardware features of the access point and describes the access point’s role in your network.Chapter 2, “Installing the Access Point,” describes how to mount the access point on a desktop, wall, or ceiling, how to connect Ethernet, serial, and power cables, and provides an installation summary, safety warnings, and general guidelines.Chapter 3, “Configuring the Access Point for the First Time,” describes how to configure basic settings on a new access point.
CISCO CONFIDENTIAL - Draft 2xCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01PrefaceConventionsChapter 4, “Using the Web-Browser Interface,” describes how to use the web-browser interface to configure the access point.Chapter 5, “Using the Command-Line Interface,” describes how to use the command-line interface (CLI) to configure the access point.Chapter 6, “Troubleshooting,” provides troubleshooting procedures for basic problems with the access point.Appendix A, “Translated Safety Warnings,” provides translations of the safety warnings that appear in this publication.Appendix B, “Declarations of Conformity and Regulatory Information,” provides declarations of conformity and regulatory information for the access point.Appendix C, “Access Point Specifications,” lists technical specifications for the access point.Appendix D, “Channels and Power Levels,” lists the access point radio channels and the maximum power levels supported by the world’s regulatory domains.Appendix E, “Console Cable Pinouts,” identifies the pinouts for the serial console cable that connects to the access point’s serial console port. ConventionsThis publication uses these conventions to convey instructions and information:Command descriptions use these conventions:•Commands and keywords are in boldface text.•Arguments for which you supply values are in italic.•Square brackets ([ ]) mean optional elements.•Braces ({ }) group required choices, and vertical bars ( | ) separate the alternative elements.•Braces and vertical bars within square brackets ([{ | }]) mean a required choice within an optional element.Interactive examples use these conventions:•Terminal sessions and system displays are in screen font.•Information you enter is in boldface screen font.•Nonprinting characters, such as passwords or tabs, are in angle brackets (< >).Notes, cautions, and timesavers use these conventions and symbols:Tip Means the following will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information.Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.
CISCO CONFIDENTIAL - Draft 2xiCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01PrefaceConventionsCaution Means reader be careful. In this situation, you might do something that could result equipment damage or loss of data.WarningThis warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. (To see translations of the warnings that appear in this publication, refer to the appendix “Translated Safety Warnings.”)WaarschuwingDit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico’s en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. (Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het aanhangsel “Translated Safety Warnings” (Vertalingen van veiligheidsvoorschriften) raadplegen.)VaroitusTämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. (Tässä julkaisussa esiintyvien varoitusten käännökset löydät liitteestä "Translated Safety Warnings" (käännetyt turvallisuutta koskevat varoitukset).)AttentionCe symbole d’avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures. Avant d’accéder à cet équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures courantes de prévention des accidents. Pour obtenir les traductions des mises en garde figurant dans cette publication, veuillez consulter l’annexe intitulée « Translated Safety Warnings » (Traduction des avis de sécurité).WarnungDieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewußt. (Übersetzungen der in dieser Veröffentlichung enthaltenen Warnhinweise finden Sie im Anhang mit dem Titel “Translated Safety Warnings” (Übersetzung der Warnhinweise).)AvvertenzaQuesto simbolo di avvertenza indica un pericolo. Si è in una situazione che può causare infortuni. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti. La traduzione delle avvertenze riportate in questa pubblicazione si trova nell’appendice, “Translated Safety Warnings” (Traduzione delle avvertenze di sicurezza).AdvarselDette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du være oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker. (Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen, kan du se i vedlegget "Translated Safety Warnings" [Oversatte sikkerhetsadvarsler].)
CISCO CONFIDENTIAL - Draft 2xiiCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01PrefaceRelated PublicationsRelated PublicationsThese documents provide complete information about the access point:•Release Notes for Cisco Aironet 1130AG Series Access Point •Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges •Cisco IOS Software Configuration Guide for Cisco Aironet Access PointsClick this link to browse to the Cisco Aironet documentation home page:http://www.cisco.com/univercd/cc/td/doc/product/wireless/index.htmTo browse to the 1200 series access point documentation, select Aironet 1200 Series Wireless LAN Products > Cisco Aironet 1200 Series Access Points.Obtaining DocumentationCisco provides several ways to obtain documentation, technical assistance, and other technical resources. These sections explain how to obtain technical information from Cisco Systems.Cisco.comYou can access the most current Cisco documentation on the World Wide Web at this URL:http://www.cisco.com/univercd/home/home.htmYou can access the Cisco website at this URL:http://www.cisco.comInternational Cisco websites can be accessed from this URL:http://www.cisco.com/public/countries_languages.shtmlAvisoEste símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos fisicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes. (Para ver as traduções dos avisos que constam desta publicação, consulte o apêndice “Translated Safety Warnings” - “Traduções dos Avisos de Segurança”).¡Advertencia!Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. (Para ver traducciones de las advertencias que aparecen en esta publicación, consultar el apéndice titulado “Translated Safety Warnings.”)Varning!Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. (Se förklaringar av de varningar som förekommer i denna publikation i appendix "Translated Safety Warnings" [Översatta säkerhetsvarningar].)
CISCO CONFIDENTIAL - Draft 2xiiiCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01PrefaceObtaining DocumentationDocumentation CD-ROMCisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which may have shipped with your product. The Documentation CD-ROM is updated regularly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual or quarterly subscription.Registered Cisco.com users can order a single Documentation CD-ROM (product number DOC-CONDOCCD=) through the Cisco Ordering tool:http://www.cisco.com/en/US/partner/ordering/ordering_place_order_ordering_tool_launch.htmlAll users can order monthly or quarterly subscriptions through the online Subscription Store:http://www.cisco.com/go/subscriptionOrdering DocumentationYou can find instructions for ordering documentation at this URL:http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htmYou can order Cisco documentation in these ways:•Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Networking Products MarketPlace:http://www.cisco.com/en/US/partner/ordering/index.shtml•Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, U.S.A.) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387). Documentation FeedbackYou can submit comments electronically on Cisco.com. On the Cisco Documentation home page, click Feedback at the top of the page.You can e-mail your comments to bug-doc@cisco.com.You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:Cisco SystemsAttn: Customer Document Ordering170 West Tasman DriveSan Jose, CA 95134-9883We appreciate your comments.
CISCO CONFIDENTIAL - Draft 2xivCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01PrefaceObtaining Technical AssistanceObtaining Technical AssistanceCisco provides Cisco.com, which includes the Cisco Technical Assistance Center (TAC) website, as a starting point for all technical assistance. Customers and partners can obtain online documentation, troubleshooting tips, and sample configurations from the Cisco TAC website. Cisco.com registered users have complete access to the technical support resources on the Cisco TAC website, including TAC tools and utilities. Cisco.comCisco.com offers a suite of interactive, networked services that let you access Cisco information, networking solutions, services, programs, and resources at any time, from anywhere in the world. Cisco.com provides a broad range of features and services to help you with these tasks:•Streamline business processes and improve productivity •Resolve technical issues with online support•Download and test software packages•Order Cisco learning materials and merchandise•Register for online skill assessment, training, and certification programsTo obtain customized information and service, you can self-register on Cisco.com at this URL:http://tools.cisco.com/RPF/register/register.doTechnical Assistance CenterThe Cisco TAC is available to all customers who need technical assistance with a Cisco product, technology, or solution. Two types of support are available: the Cisco TAC website and the Cisco TAC Escalation Center. The type of support that you choose depends on the priority of the problem and the conditions stated in service contracts, when applicable.We categorize Cisco TAC inquiries according to urgency:•Priority level 4 (P4)—You need information or assistance concerning Cisco product capabilities, product installation, or basic product configuration. There is little or no impact to your business operations.•Priority level 3 (P3)—Operational performance of the network is impaired, but most business operations remain functional. You and Cisco are willing to commit resources during normal business hours to restore service to satisfactory levels.•Priority level 2 (P2)—Operation of an existing network is severely degraded, or significant aspects of your business operations are negatively impacted by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.•Priority level 1 (P1)—An existing network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
CISCO CONFIDENTIAL - Draft 2xvCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01PrefaceObtaining Technical AssistanceLocating the Product Serial NumberThe access point serial number is located on the bottom of the cabinet (refer to Figure 1).Figure 1 Location of Serial Number Label - TBD The access point serial number label contains the following information:•Model number, such as AIR-AP1310•Serial number, such as S/N: VDF0636XXXX (11 alphanumeric digits)•MAC address, such as MAC: 00abc65094f3 (12 hexadecimal digits)•Location of manufacture, such as Made in SingaporeYou need your product serial number when requesting support from the Cisco Technical Assistance Center.Cisco TAC WebsiteThe Cisco TAC website provides online documents and tools to help troubleshoot and resolve technical issues with Cisco products and technologies. To access the Cisco TAC website, go to this URL:http://www.cisco.com/tacAll customers, partners, and resellers who have a valid Cisco service contract have complete access to the technical support resources on the Cisco TAC website. Some services on the Cisco TAC website require a Cisco.com login ID and password. If you have a valid service contract but do not have a login ID or password, go to this URL to register:http://tools.cisco.com/RPF/register/register.doIf you are a Cisco.com registered user, and you cannot resolve your technical issues by using the Cisco TAC website, you can open a case online at this URL:http://www.cisco.com/tac/caseopenIf you have Internet access, we recommend that you open P3 and P4 cases online so that you can fully describe the situation and attach any necessary files.
CISCO CONFIDENTIAL - Draft 2xviCisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01PrefaceObtaining Additional Publications and InformationCisco TAC Escalation CenterThe Cisco TAC Escalation Center addresses priority level 1 or priority level 2 issues. These classifications are assigned when severe network degradation significantly impacts business operations. When you contact the TAC Escalation Center with a P1 or P2 problem, a Cisco TAC engineer automatically opens a case.To obtain a directory of toll-free Cisco TAC telephone numbers for your country, go to this URL:http://www.cisco.com/warp/public/687/Directory/DirTAC.shtmlBefore calling, please check with your network operations center to determine the Cisco support services to which your company is entitled: for example, SMARTnet, SMARTnet Onsite, or Network Supported Accounts (NSA). When you call the center, please have available your service agreement number and your product serial number.Obtaining Additional Publications and InformationInformation about Cisco products, technologies, and network solutions is available from various online and printed sources.•The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:http://www.cisco.com/en/US/products/products_catalog_links_launch.html•Cisco Press publishes a wide range of networking publications. Cisco suggests these titles for new and experienced users: Internetworking Terms and Acronyms Dictionary, Internetworking Technology Handbook, Internetworking Troubleshooting Guide, and the Internetworking Design Guide. For current Cisco Press titles and other information, go to Cisco Press online at this URL:http://www.ciscopress.com•Packet magazine is the Cisco quarterly publication that provides the latest networking trends, technology breakthroughs, and Cisco products and solutions to help industry professionals get the most from their networking investment. Included are networking deployment and troubleshooting tips, configuration examples, customer case studies, tutorials and training, certification information, and links to numerous in-depth online resources. You can access Packet magazine at this URL:http://www.cisco.com/go/packet•iQ Magazine is the Cisco bimonthly publication that delivers the latest information about Internet business strategies for executives. You can access iQ Magazine at this URL:http://www.cisco.com/go/iqmagazine•Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:http://www.cisco.com/en/US/about/ac123/ac147/about_cisco_the_internet_protocol_journal.html•Training—Cisco offers world-class networking training. Current offerings in network training are listed at this URL:http://www.cisco.com/en/US/learning/le31/learning_recommended_training_list.html
CHAPTER CISCO CONFIDENTIAL - Draft 21-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-011OverviewCisco Aironet 1130AG Series Access Points provide a secure, affordable, and easy-to-use wireless LAN solution that combines mobility and flexibility with the enterprise-class features required by networking professionals. With a management system based on Cisco IOS software, the 1130 series access point is a Wi-Fi certified, wireless LAN transceiver. The access point contains two integrated radios: a 2.4-GHz radio (IEEE 802.11g) and a 5-GHz radio (IEEE 802.11a). You can configure the radios separately, using different settings on each radio.The access point serves as the connection point between wireless and wired networks or as the center point of a stand-alone wireless network. In large installations, wireless users within radio range of an access point can roam throughout a facility while maintaining seamless, uninterrupted access to the network.You can configure and monitor the access point using the command-line interface (CLI), the browser-based management system, or Simple Network Management Protocol (SNMP). This chapter provides information on the following topics:•Hardware Features, page 1-2•Network Configuration Examples, page 1-6
CISCO CONFIDENTIAL - Draft 21-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 1 OverviewHardware FeaturesHardware FeaturesThis section describes access point features. Refer to Appendix C, “Access Point Specifications,” for a list of access point specifications.Key hardware features of the access point include:•Dual-radio operation (see page 1-2)•Ethernet port (see page 1-3)•Console port (see page 1-3)•LEDs, (see page 1-3)•Power sources (see page 1-4)•Anti-theft features (see page 1-4) •UL 2043 certification (see page 1-6)Figure 1-1 shows the access point hardware features.Figure 1-1 Access Point Hardware Features Dual-Radio OperationThe access point supports simultaneous radio operation using a 2.4-GHz 802.11g radio and a 5-GHz 802.11a radio. Each radio uses 2-dBi dual-diversity integrated antennas.The 5-GHz radio incorporates an Unlicensed National Information Infrastructure (UNII) radio transceiver operating in the UNII 5-GHz frequency bands. The 802.11g radio is called Radio0 and the 802.11a radio is called Radio1.1Status LED 5Console port (RJ-45)248-VDC power port 6Mode button3Ethernet port (RJ-45) 7Ethernet and Radio LEDs4Keyhole slot
CISCO CONFIDENTIAL - Draft 21-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 1 OverviewHardware FeaturesEthernet PortThe auto-sensing Ethernet port accepts an RJ-45 connector, linking the access point to your 10BASE-T or 100BASE-T Ethernet LAN. The access point can receive power through the Ethernet cable from a power injector, switch, or power patch panel. The Ethernet MAC address is printed on the label on the back of the access point. The port is located in a cable bay area that is hidden by the top cover (see Figure 1-1).Console PortThe serial console port provides access to the access point’s command-line interface (CLI) using a terminal emulator program. The port is located in a cable bay area that is hidden by the top cover (see Figure 1-1). Use an RJ-45 to DB-9 serial cable to connect your computer’s COM port to the access point’s serial console port. (Refer to Appendix E, “Console Cable Pinouts,” for a description of the console port pinouts.) Assign the following port settings to a terminal emulator to open the management system pages: 9600 baud, 8 data bits, No parity, 1 stop bit and no flow control.Note Your console cable connector must not include over-molding or a cable boot because of space limitations within the cable bay area of the access point.LEDsThe report Ethernet has three LEDs to indicate Ethernet activity, association status, radio activity, and other status indications (refer to the “Checking the Access Point LEDs” section on page 6-2 for additional information).•The Status LED provides general operating status and error indications.•The Ethernet LED is located in the cable bay area under the access point top cover. This LED signals Ethernet traffic on the wired Ethernet LAN and provides Ethernet error indications. •The Radio LED signals that wireless packets are being transmitted or received over the radio interface and provides radio error indications. Figure 1-1 shows the locations of the three LEDs.
CISCO CONFIDENTIAL - Draft 21-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 1 OverviewHardware FeaturesPower SourcesThe access point can receive power from an external power module (supplied)or from inline power using the Ethernet cable. The access point supports the IEEE 802.3af inline power standard and the Cisco CDP Power Negotiation protocol. Using inline power, you do not need to run a power cord to the access point because power is supplied over the Ethernet cable. WarningThis product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. The access point supports the following power sources:•Power module (supplied)•Inline power:–Cisco Aironet Power Injector (AIR-PWRINJ3 or AIR-PWRINJ-FIB)–An inline power capable switch, such as the Cisco Catalyst 3524 PWR XL, 3560-48PS, 3570-48PS, 4500 with 802.3AF PoE module, or the 6500 with 802.3AF PoE module–Other inline power switches supporting the IEEE 802.3af inline power standardNote Some switches and patch panels might not provide enough power to operate the access point when configured with both 2.4-GHz and 5-GHz radios. On power-up if the access point is unable to determine that the power source can supply sufficient power, the access point automatically deactivates both radios to prevent an over-current condition. The access point also activates a Status LED low power error indication and creates an error log entry (refer to the “Checking the Access Point LEDs” section on page 6-2 and the “Low Power Condition” section on page 6-5).Anti-Theft FeaturesThere are three methods of securing the access point to help prevent theft:•Security cable keyhole—You can use the security cable slot to secure the access point using a standard security cable, such as those used on laptop computers.•Security hasp adapter—When you mount the access point on a wall or ceiling using the mounting plate and the security hasp, you can lock the access point to the plate with a padlock (see Figure 1-2). Compatible padlocks are Master Lock models 120T and 121T or equivalent.Note The security hasp adapter covers the cable bay area ( including the power port, Ethernet port, console port, and the mode button) to prevent the installation or removal of the cables or the activation of the mode button.
CISCO CONFIDENTIAL - Draft 21-5Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 1 OverviewHardware FeaturesFigure 1-2 Access Point with Security Hasp Adapter\•Security screw—The access point contains a security screw hole (see Figure 1-3) that can be used to attach the access point to the mounting plate to restrict access point removal. When a security-type screw (user supplied) is used, access to the mounting screws that attach the mounting plate is greatly restricted. Note The use of a security-type screw does not restrict access to the access point cables or the mode button.Figure 1-3 Access Point Security Screw Hole1Access point cover in open position 3Security padlock2Security hasp adapter1Access point cover in open position 2Security screw hole
CISCO CONFIDENTIAL - Draft 21-6Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 1 OverviewNetwork Configuration ExamplesUL 2043 CertificationThe access point has adequate fire resistance and low smoke-producing characteristics suitable for operation in a building's environmental air space, such as above suspended ceilings, in accordance with Section 300-22(c) of the NEC, and with Sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 1, C22.1.Caution Only the fiber-optic power injector (AIR-PWRINJ-FIB) has been tested to UL 2043 for operation in a building’s environmental air space, the AIR-PWRINJ3 power injector and the power module are not tested to UL 2043 and should not be placed in a building’s environmental air space, such as above suspended ceilings. Network Configuration ExamplesThis section describes the access point’s role in three common wireless network configurations. The access point’s default configuration is as a root unit connected to a wired LAN or as the central unit in an all-wireless network. The repeater role requires a specific configuration.Root Unit on a Wired LANAn access point connected directly to a wired LAN provides a connection point for wireless users. If more than one access point is connected to the LAN, users can roam from one area of a facility to another without losing their connection to the network. As users move out of range of one access point, they automatically connect to the network (associate) through another access point. The roaming process is seamless and transparent to the user. Figure 1-4 shows access points acting as root units on a wired LAN.
CISCO CONFIDENTIAL - Draft 21-7Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 1 OverviewNetwork Configuration ExamplesFigure 1-4 Access Points as Root Units on a Wired LAN - need new picture Access Point(Root Unit)Access Point(Root Unit)65999Wired LAN
CISCO CONFIDENTIAL - Draft 21-8Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 1 OverviewNetwork Configuration ExamplesRepeater Unit that Extends Wireless RangeAn access point can be configured as a stand-alone repeater to extend the range of your infrastructure or to overcome an obstacle that blocks radio communication. The repeater forwards traffic between wireless users and the wired LAN by sending packets to either another repeater or to an access point connected to the wired LAN. The data is sent through the route that provides the best performance for the client. Figure 1-5 shows an access point acting as a repeater. Consult the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points for instructions on setting up an access point as a repeater.Note Non-Cisco client devices might have difficulty communicating with repeater access points.Figure 1-5 Access Point as Repeater - need new picture Access Point(Root Unit)Access Point(Repeater)66000Wired LAN
CISCO CONFIDENTIAL - Draft 21-9Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 1 OverviewNetwork Configuration ExamplesCentral Unit in an All-Wireless NetworkIn an all-wireless network, an access point acts as a stand-alone root unit. The access point is not attached to a wired LAN; it functions as a hub linking all stations together. The access point serves as the focal point for communications, increasing the communication range of wireless users. Figure 1-6 shows an access point in an all-wireless network.Figure 1-6 Access Point as Central Unit in All-Wireless Network - need new picture Access Point(Root Unit)65998
CISCO CONFIDENTIAL - Draft 21-10Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 1 OverviewNetwork Configuration Examples
CHAPTER CISCO CONFIDENTIAL - Draft 22-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-012Installing the Access PointThis chapter describes the installation of the access point and includes these sections:•Safety Information, page 2-2•Warnings, page 2-2•Unpacking the Access Point, page 2-3•Basic Installation Guidelines, page 2-3•Before Beginning the Installation, page 2-4•Installation Summary, page 2-7•Opening the Access Point Cover, page 2-8•Mounting the Access Point, page 2-9•Attaching the Access Point to the Mounting Plate, page 2-16•Connecting the Ethernet and Power Cables, page 2-17•Securing the Access Point, page 2-19•Powering Up the Access Point, page 2-21
CISCO CONFIDENTIAL - Draft 22-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointSafety InformationSafety InformationFollow the guidelines in this section to ensure proper operation and safe use of the access point.FCC Safety Compliance StatementThe FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. When used with approved Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper installation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits.General Safety Guidelines•Do not hold any component containing a radio so that the antenna is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.•The use of wireless devices in hazardous locations is limited to the constraints posed by the local codes, the national codes, and the safety directors of such environments.WarningsTranslated versions of the following safety warnings are provided in Appendix A, “Translated Safety Warnings.”WarningRead the installation instructions before you connect the system to its power source. Statement 1004WarningThis product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 15A Statement 1005WarningDo not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. Statement 245BWarningIn order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons. Statement 332WarningDo not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001
CISCO CONFIDENTIAL - Draft 22-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointUnpacking the Access PointUnpacking the Access PointFollow these steps to unpack the access point:Step 1 Open the shipping container and carefully remove the contents. Step 2 Return all packing materials to the shipping container and save it.Step 3 Ensure that all items listed in the “Package Contents” section are included in the shipment. Check each item for damage. If any item is damaged or missing, notify your authorized Cisco sales representative. Package ContentsEach access point package contains the following items:•Cisco Aironet 1130AG Series Access Point•Cisco Aironet 1130AG Series Power Module (universal power supply)•Mounting hardware kit–One mounting plate –Two suspended ceiling adjustable T-rail clips–One security hasp adapter–Four 6x32x¼ inch flat head Phillips head machine screws–One 8x32x3/16 inch pan head Phillips head machine screws–2 #8 plastic wall anchors–2 #8x32x1inch pan head screws•Quick Start Guide: Cisco Aironet 1130AG Series Access Point•Cisco product registration and Cisco documentation feedback cardsIf anything is missing or damaged, contact your Cisco representative for support.Basic Installation GuidelinesBecause the access point is a radio device, it is susceptible to interference that can reduce throughput and range. Follow these basic guidelines to ensure the best possible performance:•Install the access point in an area where metal structures such as shelving units, bookcases, filing cabinets, and metal gridwork do not block the radio signals to and from the access point.•Install the access point away from microwave ovens. Microwave ovens operate on the same frequency as the access point and can cause signal interference.
CISCO CONFIDENTIAL - Draft 22-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointBefore Beginning the InstallationBefore Beginning the InstallationBefore you begin the installation process, please refer to these sections to become familiar with the access point and the mounting hardware:•“Access Point Layout and Connectors” section on page 2-4•“Mounting Plate” section on page 2-5•“Suspended Ceiling Adjustable T-Rail Clips” section on page 2-6Access Point Layout and ConnectorsFigure 2-1 identifies the main access point hardware features.Figure 2-1 Access Point Hardware Features - TBD Note There is a second keyhole slot located on the bottom of the unit near the security slot.1Status LED 5Console port (RJ-45)248-VDC power port 6Mode button3Ethernet port (RJ-45) 7Ethernet and Radio LEDs4Keyhole slot
CISCO CONFIDENTIAL - Draft 22-5Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointBefore Beginning the InstallationMounting PlateThe access point mounting plate is designed to accomodate multiple mounting methods. The mounting holes on the plate are marked so you can easily identify the correct holes for a specific mounting method. You can use the mounting plate as a template to mark the locations for the cable hole and the mounting holes for your wall or ceiling installation. Refer to Figure 2-2 to locate the various mounting holes for the method you intend to use.Figure 2-2 Mounting PlateThe mounting plate features are described below:•Keyhole clips—used to attach the access point to the mounting plate. The keyhole clips slide into the access point keyhole slots on the bottom of the unit.•Screw holes (A, B, C)—used to attach to the suspended ceiling adjustable T-rail clips. •Screw hole (X)—used to attach to a network cable box, wall, or ceiling. The mounting kit contains two 8x32x1 inch pan head screws and wall anchors for wall or ceiling mounting.•Security screw hole—used to secure the access point to the mounting plate. Note You can use a special security screw to restrict the removal of the access point from the mounting plate.1Keyhole clip 4Screw hole (X) 2Screw holes (A, B, C) 5Security screw hole3Location for cable access hole 6Padlock hole
CISCO CONFIDENTIAL - Draft 22-6Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointBefore Beginning the Installation•Padlock hole—used to attach a padlock to secure the access point to the mounting plate. Compatible padlocks are Master Lock models 120T and 121T or equivalent. The security hasp adapter can also be used with the padlock for increase security protection.Note The security hasp covers the cable bay area ( including the power port, Ethernet port, console port, and the mode button) to prevent the installation or removal of the cables or the activation of the mode button.Suspended Ceiling Adjustable T-Rail ClipsThe accessory kit contains two suspended ceiling adjustable T-rail clips; one for standard ceiling tile rails and the other for recessed ceiling tile rails. The clips are adjustable to accomodate three standard T-rail widths. Each clip contains detents that are used to adjust the clip to the T-rail. Each detent contains markings that indicate the T-rail width and the hole letter that corresponds to the correct mounting holes on the mounting plate. Figure 2-3 shows the details of the adjustable T-rail clips.Figure 2-3 T-Rail Clip Features 1Adjustable T-rail clip 3T-rail locking screw2Mounting plate screw holes (8x32 flat head screw)4T-rail width adjustment detents (A, B, C) correspond to the A, B, and C holes on the mounting plate
CISCO CONFIDENTIAL - Draft 22-7Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointInstallation SummaryThe adjustable T-rail clip attaches to the mounting plate using four 6x32x1/4 inch flat head screws. The A, B, and C holes on the T-rail clips and the mounting plate correspond to these T-rail widths:•A holes—used for 1 1/2 in (38 mm) T-rails•B holes—used for 15/16 in (24 mm) T-rails•C holes—used for 9/16 in (15 mm) T-railsFigure 2-4 indicates where you should push to open and close the adjustable T-rail clips.Figure 2-4 Adjusting the T-Rail Clips Installation SummaryWhile installing the access point, you must perform the following operations:•Open the access point cover (see “Opening the Access Point Cover” section on page 2-8).•Mount the access point on a convenient flat horizontal or vertical surface, such as a desktop, book shelf, file cabinet, wall, ceiling, or suspended ceiling T-rail (see the “Mounting the Access Point” section on page 2-9). •Attach the access point to the mounting plate (see the “Attaching the Access Point to the Mounting Plate” section on page 2-16).•Connect Ethernet and power cables (see the “Connecting the Ethernet and Power Cables” section on page 2-17).•Secure the access point (see the “Securing the Access Point” section on page 2-19). •Configure basic settings (refer to Chapter 3, “Configuring the Access Point for the First Time”).•Configure security and other access point options (refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points). 1Push here to open 2Push here to close
CISCO CONFIDENTIAL - Draft 22-8Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointOpening the Access Point CoverOpening the Access Point CoverThe top cover provides access to the access point cable bay area containing the power connector, Ethernet port, console serial port, the mode button, and the Ethernet and Radio LEDs. Caution Do not attempt to pry open or lift the top cover of the access point, because you could damage the cover. Carefully read the instructions in this section before attempting to open the access point cover.The cover is designed to partially open by sliding back from a secured position. Follow these steps to open the top cover:Step 1 Locate the cable opening on the end of the unit (see Figure 2-5). Figure 2-5 Cable Opening in Access Point HousingStep 2 Place your thumb on the top cover (above the triangle mark ) and gently push towards the Status LED.1Top cover 2Cable Opening
CISCO CONFIDENTIAL - Draft 22-9Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointMounting the Access PointStep 3 Continue to slowly slide the cover back across the access point until you reach the cover stop (see Figure 2-6).Figure 2-6 Opening the Access Point Cover Mounting the Access PointThis section describes the steps necessary to mount the access point using thesemethods:•Horizontal or vertical surface—see the “Mounting on a Horizontal or Vertical Surface” section on page 2-10•Under a suspended ceiling—“Mounting Below a Suspended Ceiling” section on page 2-11•Network cable box—“Mounting on a Network Cable Box” section on page 2-14•Desktop or shelf—see the “Mounting on a Desktop or Shelf” section on page 2-151Access point cover (maximum open position) 3Opening direction2Cable bay area 4Cable opening (in access point housing)
CISCO CONFIDENTIAL - Draft 22-10Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointMounting the Access PointMounting on a Horizontal or Vertical SurfaceFollow these steps to mount the access point on a horizontal or vertical surface:Step 1 Use the mounting plate as a template to mark the locations of the two mounting holes (labled with an X) and the location of the cable access hole (see Figure 2-7).Figure 2-7 Mounting Plate Step 2 Drill one of the following sized holes at the X mounting hole locations you marked:•3/16 in. (4.7 mm) if you are using the supplied wall anchors•1/8 in. (6.3 mm) if you are not using wall anchorsStep 3 Insert the wall anchors into the mounting holes if you are using them.Step 4 If needed, drill or cut a cable access hole large enough for the access point cables and pull the cables through the access hole until you have about 1 foot of exposed cables protruding from the hole.1Keyhole clip 3X mounting hole2Cable access hole location 4Padlock hole
CISCO CONFIDENTIAL - Draft 22-11Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointMounting the Access PointStep 5 Position the mounting plate over the wall anchors or the drilled holes.Step 6 Insert two 8x32x1inch pan head screws in the X mounting holes and tightening.To attach the access point to the mounting plate, see “Attaching the Access Point to the Mounting Plate” section on page 2-16.Mounting Below a Suspended Ceiling You should review Figure 2-8 before beginning the mounting process.Figure 2-8 Adjustable T-Rail ClipsFollow these steps to mount your access point on a suspended ceiling:Step 1 Decide where you want to mount the access point on your suspended ceiling.Step 2 Select the appropriate adjustable T-rail clip for your suspended ceiling and open the clip to the maximum (see Figure 2-4).Step 3 Unscrew the two T-rail locking set screws to enable placing the clip over a T-rail.1T-rail locking set screw 3T-rail width detents (A, B, or C)2Mounting plate screw holes
CISCO CONFIDENTIAL - Draft 22-12Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointMounting the Access PointStep 4 Place the T-rail clip over the T-rail and close the T-rail clip (see Figure 2-4).Step 5 Tighten the two T-rail locking set screws to prevent the T-rail clip from moving.Step 6 Observe the T-rail width detent letter (A, B, or C) that corresponds to the T-rail width.Step 7 Align the corresponding (A, B, or C) holes on the mounting plate over the T-rail mounting plate holes.Step 8 Hold the mounting plate and insert a 6x32x1/4 flat head screw into each of the corresponding (A, B, or C) holes and tighten.Step 9 If needed, drill or cut a cable access hole (see Figure 2-7) large enough for the access point cables and pull the cables through the access hole until you have about 1 foot of exposed cables protruding from the hole. To attach the access point to the mounting plate, see “Attaching the Access Point to the Mounting Plate” section on page 2-16.
CISCO CONFIDENTIAL - Draft 22-13Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointMounting Above a Suspended CeilingMounting Above a Suspended CeilingThe access point mounting bracket is designed to be integrated into the T-bar grid above the tiles of a suspended ceiling. The access point uses a T-bar box hanger (not supplied) such as the Erico Caddy 512 or B-Line BA12 and should be oriented just above the top surface of a standard 5/8-in. (1.59 cm) ceiling tile. You may need to modify a thicker tile to allow room for the access point.Caution Only the fiber-optic power injector (AIR-PWRINJ-FIB) has been tested to UL 2043 for operation in a building’s environmental air space, the AIR-PWRINJ3 power injector and the power module are not tested to UL 2043 and should not be placed in a building’s environmental air space, such as above suspended ceilings. Caution Cisco does not sell Ethernet cable rated for use in a building environmental air space, such as above suspended ceilings. You must obtain special Ethernet cable with the appropriate rating.Follow these steps to mount the access point above a suspended ceiling. Refer Figure 2-9 before proceeding.Figure 2-9 T-Bar Grid Mounting Bracket PartsStep 1 Insert the bracket mounting clip’s tab into the rectangular hole on the access point mounting bracket.1Suspended ceiling T-rail 4Access point mounting bracket2T-bar box hanger 5Access point3Bracket mounting clip 6T-rail clip5857761126643
CISCO CONFIDENTIAL - Draft 22-14Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointMounting Above a Suspended CeilingStep 2 Place the clip over the T-bar box hanger (refer to Figure 2-10) and secure it to the access point mounting bracket with the 1/4-20 fastener (supplied with the T-bar hanger).Figure 2-10 T-Bar and Mounting Bracket - TBDNote Figure 2-10 shows the access point mounting bracket mounted perpendicular to the T-bar box hanger. You can also mount the bracket parallel to the T-bar box hanger.Step 3 Remove a ceiling tile adjacent to the mounting location.Step 4 Configure the ends of the T-bar box hanger to allow for maximum clearance above the ceiling tile. See the illustration above.Step 5 Open the access point cover and connect the Ethernet cable to the access point (see the “Connecting to an Ethernet Network with an Inline Power Source” section on page 2-18).Step 6 Attach the access point to the access point mounting bracket (see the “Attaching the Access Point to the Mounting Plate” section on page 2-16).Step 7 Attach the T-rail clips on the each end of the T-bar box hanger to the ceiling grid T-rails. Make sure the clips are securely attached to the T-rails.Step 8 Connect a drop wire to a building structural element and the hole provided in the bracket mounting clip. This additional support is required in order to comply with the U.S. National Electrical Safety Code.Step 9 If you need additional security, you can secure the access point to a nearby immovable object using a Kensington lock and security cable (see the “Securing the Access Point” section on page 2-19).Step 10 Verify that the access point is operating before replacing the ceiling tile. Mounting on a Network Cable BoxFollow these steps to mount the access point on a network cable box.Step 1 Position the mounting plate over the newtowk cable box and align the two mounting holes (labled with a X) with the network cable box holes.Step 2 Hold the mounting plate and insert a 6x32x1/4 flat head screw into each of the X mounting holes and tighten.Step 3 Pull the access point cables out of the network box until there is about 1 foot of exposed cables protruding from the box.85777
CISCO CONFIDENTIAL - Draft 22-15Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointMounting Above a Suspended CeilingTo attach the access point to the mounting plate, see “Attaching the Access Point to the Mounting Plate” section on page 2-16. Mounting on a Desktop or ShelfWhen placing the access point on a desktop of shelf, you do not need the mounting plate. The access point has four rubber pads on the bottom to help prevent sliding or scratching the surface of your desktop or shelf. For information on connecting the access point cables, see the “Connecting the Ethernet and Power Cables” section on page 2-17. Rotating the Cisco LogoThe Cisco logo on the top of the unit can be rotated to correctly position the logo for any mounting arrangement, such as when the unit is mounted on a vertical wall, the logo should oriented with the Cisco Systems positioned on top. The logo should always be oriented to ease reading.To rotate the Cisco logo, peform these steps:Step 1 Place the end of an opened paper clip into one of the holes on the logo assembly (see Figure 2-11).Figure 2-11 Cisco Logo HolesStep 2 Using the paper clip as a handle, rotate the logo until you reach the desired orientation.Step 3 Remove the paper clip.1Cisco logo 2Status LED3Logo assembly holes
CISCO CONFIDENTIAL - Draft 22-16Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointAttaching the Access Point to the Mounting PlateAttaching the Access Point to the Mounting PlateFollow these steps to attach the access point to the mounting plate:Step 1 Open the access point cover (see the “Opening the Access Point Cover” section on page 2-8).Step 2 In the cable bay area, pull the cables through one of the access point cable openings (see Figure 2-6).Step 3 In the cable bay area, line up the visible access point keyhole with the mounting plate keyhole clip located near the security padlock hole (see Figure 2-12).Figure 2-12 Aligning the Keyhole Clip to the Access Point KeyholeStep 4 Insert the keyhole clip into the keyhole and maintain a slight pressure to hold the access point in place.Step 5 Slightly rotate the access point from side-to-side until you hear the second keyhole clip falling into the other keyhole (not visible).Step 6 Slide the access point back over the keyhole clips. You will hear a click when the locking detent contacts the access point and locks it into place.For instructions on connecting your cables, refer to the “Connecting the Ethernet and Power Cables” section on page 2-17.1Access point keyhole 4Security screw hole2Mounting plate keyhole clip 5Padlock hole3Mounting plate
CISCO CONFIDENTIAL - Draft 22-17Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointConnecting the Ethernet and Power CablesConnecting the Ethernet and Power CablesThe access point receives power through the Ethernet cable or an external power module. Figure 2-13 shows the power options for the access point. Figure 2-13 Access Point Power Options - need new picture with Ajax WarningThis product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. The access point supports the following power sources:•Power module (supplied)•Inline power:–Cisco Aironet Power Injector (AIR-PWRINJ3 or AIR-PWRINJ-FIB)–An inline power capable switch, such as the Cisco Catalyst 3524 PWR XL, 3560-48PS, 3570-48PS, 4500 with 802.3AF PoE module, or the 6500 with 802.3AF PoE module–Other inline power switches supporting the IEEE 802.3af inline power standardNote Some switches and patch panels might not provide enough power to operate the access point when configured with both 2.4-GHz and 5-GHz radios. On power-up if the access point is unable to determine that the power source can supply sufficient power, the access point automatically deactivates both radios to prevent an over-current condition. The access point also activates a Status LED low power error indication and creates an error log entry (refer to the “Checking the Access Point LEDs” section on page 6-2 and the “Low Power Condition” section on page 6-5).PowercordUniversalpower supplySYSTRPSDUPLXMODESPEEDUTILSTAT12345678910 11121314151617 1819 2021222324232410Base-T / 100Base-TX100Base-FXCatalyst 2950 SERIESSYSTRPSDUPLXMODESPEEDUTILSTAT1234567891011121314 151617 18192021 222324232410Base-T / 100Base-TX100Base-FXCatalyst 2950 SERIESSYSTRPSDUPLXMODESPEEDUTILSTAT12345678910 11121314 1516 171819 20212223 2423 2410Base-T / 100Base-TX100Base-FXCatalyst 2950 SERIESSYSTRPSDUPLXMODESPEEDUTILSTATTOAP/ BRIDGETONETWORKSwitch withinline powerPower injectorAccess PointSwitch(without inline power)Switch(without inline power)Inline PowerPatch PanelOption 1 Option 2 Option 3Option 474164
CISCO CONFIDENTIAL - Draft 22-18Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointConnecting the Ethernet and Power CablesConnecting to an Ethernet Network with an Inline Power SourceCaution The Cisco Aironet Power Injectors are not tested to UL 2043 and should not be placed in a building's environmental air space, such as above suspended ceilings.Follow these steps to connect the access point to the Ethernet LAN when you have an inline power source:Step 1 If necessary, open the access point cover (see the “Opening the Access Point Cover” section on page 2-8).Step 2 Pull the Category 5 Ethernet cable out of the access point cable bay area approximately 1 foot.Step 3 Loop the cable back towards the Ethernet connector (see Figure 2-14)Figure 2-14 Looping the Ethernet CableStep 4 Connect the Ethernet cable to the RJ-45 Ethernet connector labeled Ethernet on the access point (see Figure 2-1). Step 5 Push or pull the excess cable length (the loop) back through the access point cable bay area.Step 6 Close the access point cover by sliding it over the cable bay area until a click is heard.Step 7 Connect the other end of the Ethernet cable to one of the following:•A switch with inline power (see the “Connecting the Ethernet and Power Cables” section on page 2-17).•The end of a Cisco Aironet power injector labeled To AP/Bridge. Connect the other end labeled To Network to your 10/100 Ethernet LAN.
CISCO CONFIDENTIAL - Draft 22-19Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointSecuring the Access PointConnecting to an Ethernet Network with Local PowerFollow these steps to connect the access point to an Ethernet LAN when you are using a local power source:Step 1 If necessary, open the access point cover (see the “Opening the Access Point Cover” section on page 2-8).Step 2 Pull the Category 5 Ethernet cable and the power module cable out of the access point cable bay area approximately 1 foot.Step 3 Loop the Ethernet cable back towards the access point Ethernet connector (see Figure 2-14).Step 4 Connect the Ethernet cable to the RJ-45 Ethernet connector labeled Ethernet on the access point (see Figure 2-1). Step 5 Loop the power cable back towards the access point 48-VDC power port (see Figure 2-1 for the location of the power port).Step 6 Connect the power module output connector to the access point power port.Step 7 Push or pull the excess cable lengths (both loops) back through the access point cable bay area.Step 8 Close the access point cover by sliding it over the cable bay area until a click is heard.Step 9 Plug the other end of the Ethernet cable into an unpowered Ethernet port on your LAN network.Step 10 Plug the other end of the power module into an approved 100- to 240-VAC outlet.For information on securing your access point, see the “Securing the Access Point” section on page 2-19.Securing the Access PointThe access point supports two methods of restricting the removal of the access point. •Using a security cable•Securing the access point to the mounting plateUsing a Security CableThe access point housing provides a security cable slot to secure the access point using a standard security cable, such as those used on laptop computers. The access point security cable slot is located on one side of the unit.
CISCO CONFIDENTIAL - Draft 22-20Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointSecuring the Access PointSecuring the Access Point to the Mounting PlateThe mounting plate contains a security padlock hole and a security screw hole to enable you to secure your access point to the mounting plate to restrict it’s removal. You can use a security-type screw (that you provide) to attach the access point to the mounting plate using the security screw hole (see Figure 2-12).Note Using a security-type screw to secure the access point to the mounting plate does not prevent someone from inserting or removing the access point cables or pressing the mode button.You can use the security hasp adapter (supplied) and a padlock (that you provide) to secure your access point to the mounting plate. Compatible padlocks are Master Lock models 120T or 121T. Note The security hasp adapter covers the cable bay area (including the power port, Ethernet port, console port, and the mode button) to prevent the installation or removal of the cables or the activation of the mode button.Follow these instructions to install the security hasp adapter:Step 1 Open the access point cover (see the “Opening the Access Point Cover” section on page 2-8).Step 2 Carefully insert the access point security hasp tab into the notch on the security hasp adapter (see Figure 2-15).Figure 2-15 Installing the Security Hasp Adapter Step 3 Push down on the security hasp adapter to ensure the padlock hole is not blocked.Step 4 Insert a padlock into the padlock hole and lock the padlock.1Access point security hasp tab 3Security hasp adapter2Security hasp notch
CISCO CONFIDENTIAL - Draft 22-21Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointPowering Up the Access PointStep 5 Position the padlock into the padlock area.Step 6 Close the access point cover by sliding it over the security hasp adapter until you hear a click.Powering Up the Access Point When power is applied to the access point, it begins a routine power-up sequence that you can monitor by observing the Status LED on top of the access point. On initial power-up the LED changes colors indicating various POST activities, such as the Status LED turns dark green for about 30 seconds to indicate loading of the Cisco IOS operating system. After a successful power-up sequence, the LED turns light green to signify there are no client devics associated or it turns light blue to signify that there are client devices associated. Refer to Chapter 6, “Troubleshooting,” for complete LED descriptions.When the Status LED turns light green or light blue, you are ready to obtain the access point’s IP address and perform an initial configuration. For instructions on assigning basic settings to the access point, refer to Chapter 3, “Configuring the Access Point for the First Time,”
CISCO CONFIDENTIAL - Draft 22-22Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 2 Installing the Access PointPowering Up the Access Point
CHAPTER CISCO CONFIDENTIAL - Draft 23-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-013Configuring the Access Point for the First TimeThis chapter describes how to configure basic settings on your access point for the first time. The contents of this chapter are similar to the instructions in the quick start guide that shipped with your access point. You can configure all the settings described in this chapter using the CLI, but it might be simplest to browse to the access point’s web-browser interface to complete the initial configuration and then use the CLI to enter additional settings for a more detailed configuration. This chapter contains these sections:•Before You Start, page 3-2•Obtaining and Assigning an IP Address, page 3-3•Connecting to the Access Point Locally, page 3-3•Assigning Basic Settings, page 3-4•Protecting Your Wireless LAN, page 3-9•Using the IP Setup Utility, page 3-9•Assigning an IP Address Using the CLI, page 3-11•Using a Telnet Session to Access the CLI, page 3-11
CISCO CONFIDENTIAL - Draft 23-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 3 Configuring the Access Point for the First TimeBefore You StartBefore You StartBefore you install the access point, make sure you are using a computer connected to the same network as the access point, and obtain the following information from your network administrator:•A system name for the access point•The case-sensitive wireless service set identifiers (SSIDs) for your 802.11g and 02.11a radio networks•If not connected to a DHCP server, a unique IP address for your access point (such as 172.17.255.115)•If the access point is not on the same subnet as your PC, a default gateway address and subnet mask•A Simple Network Management Protocol (SNMP) community name and the SNMP file attribute (if SNMP is in use)•If you use IPSU to find or assign the access point IP address, the MAC address from the label on the bottom of the access point (such as 00164625854c)Resetting the Access Point to Default SettingsUsing the Mode ButtonIf you need to start over during the initial setup process, follow these steps to reset the access point to factory default settings using the access point MODE button:Step 1 Open the access point cover (refer to the “Opening the Access Point Cover” section on page 2-8).Step 2 Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.Step 3 Press and hold the MODE button while you reconnect power to the access point until the Ethernet LED turns an amber color, approximately 2 to 3 seconds, and release the button. All access point settings return to factory defaults.Using the Web-Browser InterfacePrior to using the web-browser interface, you must have the access point IP address (see the “Obtaining and Assigning an IP Address” section on page 3-3).Follow these steps to return to default settings using the web-browser interface:Step 1 Open your Internet browser. You must use Microsoft Internet Explorer (version 5.x or later) or Netscape Navigator (version 4.x).Step 2 Enter the access point’s IP address in the browser address line and press Enter. An Enter Network Password window appears.Step 3 Enter your username in the User Name field. The default username is Cisco.Step 4 Enter the access point password in the Password field and press Enter. The default password is Cisco. The Summary Status page appears.
CISCO CONFIDENTIAL - Draft 23-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 3 Configuring the Access Point for the First TimeObtaining and Assigning an IP AddressStep 5 Click System Software and the System Software screen appears.Step 6 Click System Configuration and the System Configuration screen appears.Step 7 Click the Reset to Defaults button.Note If the access point is configured with a static IP address, the IP address does not change.Obtaining and Assigning an IP AddressTo browse to the access point’s Express Setup page, you must either obtain or assign the access point’s IP address using one of the following methods:Note The access point does not have a default IP address.•To assign a static IP address to the access point, connect to the access point console port (see the “Connecting to the Access Point Locally” section on page 3-3) and follow the steps in the “Assigning an IP Address Using the CLI” section on page 3-11.•Use a DHCP server (if available) to automatically assign an IP address. You can find out the DHCP-assigned IP address using one of the following methods:–Connect to the access point console port and use a Cisco IOS CLI command to display the IP address, such as show interface bvi1. Follow the steps in the “Connecting to the Access Point Locally” section on page 3-3 to connect to the console port.–Provide your organization’s network administrator with your access point’s Media Access Control (MAC) address. Your network administrator will query the DHCP server using the MAC address to identify the IP address. The access point’s MAC address is on label attached to the bottom of the access point.–Use the Cisco IP Setup Utility (IPSU) to identify the assigned address. IPSU runs on most Microsoft Windows operating systems: Windows 9x, 2000, Me, NT, and XP.For information on IPSU, refer to “Using the IP Setup Utility” section on page 3-9. Connecting to the Access Point LocallyIf you need to configure the access point locally (without connecting the access point to a wired LAN), you can connect a PC to its console port using a DB-9 to RJ-45 serial cable. Follow these steps to open the CLI by connecting to the access point console port:Step 1 Open the access point cover (refer to “Opening the Access Point Cover” section on page 2-8).Step 2 Connect a nine-pin, female DB-9 to RJ-45 serial cable to the RJ-45 console port on the access point and to the COM port on a computer.
CISCO CONFIDENTIAL - Draft 23-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 3 Configuring the Access Point for the First TimeAssigning Basic SettingsTip If your serial cable enters from the lower cable bay area, you should loop the cable as shown in Figure 2-14.Figure 3-1 shows the console port location.Figure 3-1 Console Port LocationNote The Cisco part number for the DB-9 to RJ-45 serial cable is AIR-CONCAB1200. Browse to http://www.cisco.com/go/marketplace to order a serial cable.Step 3 Set up a terminal emulator on your PC to communicate with the access point. Use the following settings for the terminal emulator connection: 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control.Assigning Basic SettingsAfter you determine or assign the access point’s IP address, you can browse to the access point’s Express Setup page and perform an initial configuration:Step 1 Open your Internet browser. You must use Microsoft Internet Explorer (version 5.x or later) or Netscape Navigator (version 4.x).Step 2 Enter the access point’s IP address in the browser address line and press Enter. An Enter Network Password screen appears.Step 3 Press Tab to bypass the Username field and advance to the Password field.Step 4 Enter the case-sensitive password Cisco and press Enter. The Summary Status page appears. 1Console port
CISCO CONFIDENTIAL - Draft 23-5Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 3 Configuring the Access Point for the First TimeAssigning Basic SettingsFigure 3-2 shows the Summary Status page.Figure 3-2 Summary Status Page
CISCO CONFIDENTIAL - Draft 23-6Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 3 Configuring the Access Point for the First TimeAssigning Basic SettingsStep 5 Click Express Setup. The Express Setup screen appears. Figure 3-3 shows the Express Setup page.Figure 3-3 Express Setup Page Step 6 Enter the configuration settings you obtained from your system administrator. The configurable settings include:•System Name— The system name, while not an essential setting, helps identify the access point on your network. The system name appears in the titles of the management system pages.•Configuration Server Protocol—Click on the button that matches the network’s method of IP address assignment.–DHCP—IP addresses are automatically assigned by your network’s DHCP server.–Static IP—The access point uses a static IP address that you enter in the IP address field.
CISCO CONFIDENTIAL - Draft 23-7Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 3 Configuring the Access Point for the First TimeAssigning Basic Settings•IP Address—Use this setting to assign or change the access point’s IP address. If DHCP is enabled for your network, leave this field blank. Note If the access point’s IP address changes while you are configuring the access point using the web-browser interface or a Telnet session over the wired LAN, you lose your connection to the access point. If you lose your connection, reconnect to the access point using its new IP address. Follow the steps in the “Resetting the Access Point to Default Settings” section on page 3-2 if you need to start over.•IP Subnet Mask—Enter the IP subnet mask provided by your network administrator so the IP address can be recognized on the LAN. If DHCP is enabled, leave this field blank. •Default Gateway—Enter the default gateway IP address provided by your network administrator. If DHCP is enabled, leave this field blank. •Radio Service Set ID (SSID)—Enter the case-sensitive SSID (32 alphanumeric characters maximum) provided by your network administrator. The SSID is a unique identifier that client devices use to associate with the access point. •Broadcast SSID in Beacon—Use this setting to allow devices that do not specify an SSID to associate with the access point.–Yes—This is the default setting; it allows devices that do not specify an SSID to associate with the access point.–No—Devices must specify an SSID to associate with the access point. With No selected, the SSID used by the client devices must match exactly the access point’s SSID.•Role in Radio Network—Click on the button that describes the role of the access point on your network. Select Access Point (Root) if your access point is connected to the wired LAN. Select Repeater (Non-Root) if it is not connected to the wired LAN.•Optimize Radio Network for—Use this setting to select either preconcerted settings for the access point radio or customized settings for the access point radio.–Throughput—Maximizes the data volume handled by the access point but might reduce its range.–Range—Maximizes the access point’s range but might reduce throughput.–Custom—The access point uses settings you enter on the Network Interfaces: Radio-802.11b Settings page. Clicking Custom takes you to the Network Interfaces: Radio-802.11b Settings page.•Aironet Extensions—Enable this setting if there are only Cisco Aironet devices on your wireless LAN.•SNMP Community—If your network is using SNMP, enter the SNMP Community name provided by your network administrator and select the attributes of the SNMP data (also provided by your network administrator).
CISCO CONFIDENTIAL - Draft 23-8Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 3 Configuring the Access Point for the First TimeAssigning Basic SettingsStep 7 Click Apply to save your settings. If you changed the IP address, you lose your connection to the access point. Browse to the new IP address to reconnect to the access point.Your access point is now running but probably requires additional configuring to conform to your network’s operational and security requirements. Consult the chapters in this manual for the information you need to complete the configuration. Note You can restore the access point to its factory defaults by unplugging the power jack and plugging it back in while holding the Mode button down until the Ethernet LED turns an amber color (approximately 2 to 3 seconds).Default Settings on the Express Setup PageTable 3-1 lists the default settings for the settings on the Express Setup page. Table 3-1 Default Settings on the Express Setup PageSetting DefaultSystem Name apConfiguration Server Protocol DHCPIP Address Assigned by DHCPNote The access point does not have a default IP address.IP Subnet Mask Assigned by DHCPDefault Gateway Assigned by DHCP Radio Service Set ID (SSID) tsunamiBroadcast SSID in Beacon Yes11. When you assign multiple SSIDs, this setting no longer appears.Role in Radio Network Access point (root)Optimize Radio Network for ThroughputAironet Extensions EnableSNMP Community defaultCommunity
CISCO CONFIDENTIAL - Draft 23-9Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 3 Configuring the Access Point for the First TimeProtecting Your Wireless LANProtecting Your Wireless LANAfter you assign basic settings to your access point, you must configure security settings to prevent unauthorized access to your network. Because it is a radio device, the access point can communicate beyond the physical boundaries of your building. Configure some combination of these security features to protect your network from intruders:•Unique SSIDs that are not broadcast in the access point beacon (see Cisco IOS Software Configuration Guide for Cisco Aironet Access Points)•WEP and additional WEP features, such as TKIP and broadcast key rotation (see Cisco IOS Software Configuration Guide for Cisco Aironet Access Points)•Dynamic WEP and client authentication (see Cisco IOS Software Configuration Guide for Cisco Aironet Access Points)Using the IP Setup UtilityIPSU enables you to find the access point’s IP address when it has been assigned by a DHCP server. The access point must have an IP address before IPSU can be used. This section explains how to install the utility and how to use it to find the access point’s IP address.Note IPSU can be used only on the following operating systems: Windows 95, 98, NT, 2000, ME, or XP. Note IPSU can not be used to set the access point IP address or SSID.Tip Another simple way to find the access point’s IP address is to look on the Status screen in the Aironet Client Utility on a client device associated to the access point.Obtaining and Installing IPSUIPSU is available on the Cisco web site. Follow these steps to obtain and install IPSU:Step 1 Use your Internet browser to access the Cisco Software Center at the following URL:http://www.cisco.com/public/sw-center/sw-wireless.shtmlStep 2 Click Option 2: Aironet Wireless Software Display Tables.Step 3 Locate the access point firmware and utilities section and click Cisco Aironet 1130AG Series (Cisco IOS Software).Step 4 Click IPSUvxxxxxx.exe. The vxxxxxx identifies the software package version number.Step 5 On the Encryption Authorization Form, enter the requested information, read the encryption information, and check the boxes that apply.Step 6 Click Submit.Step 7 Read and accept the terms and conditions of the Software License Agreement.
CISCO CONFIDENTIAL - Draft 23-10Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 3 Configuring the Access Point for the First TimeUsing the IP Setup UtilityStep 8 Select the file again to download it.Step 9 Download and save the file to a temporary directory on your hard drive and then exit the Internet browser. Step 10 Double-click IPSUvxxxxxx.exe in the temporary directory to expand the file.Step 11 Double-click Setup.exe and follow the steps provided by the installation wizard to install IPSU.The IPSU icon appears on your computer desktop.Using IPSU to Find the Access Point’s IP AddressIf your access point receives an IP address from a DHCP server, you can use IPSU to find its IP address. Because IPSU sends a reverse-ARP request based on the access point MAC address, you must run IPSU from a computer on the same subnet as the access point and the access point must have an IP address. Follow these steps to find the access point’s IP address:Step 1 Double-click the IPSU icon on your computer desktop to start the utility. The IPSU screen appears (see Figure 3-4).Figure 3-4 IPSU Get IP Address ScreenStep 2 When the utility window opens, make sure the Get IP addr radio button in the Function box is selected.Step 3 Enter the access point’s MAC address in the Device MAC ID field. The access point’s MAC address is printed on the label on the bottom of the unit. It should contain six pairs of hexadecimal digits. Your access point’s MAC address might look like the following example:000164xxxxxxNote The MAC address field is not case-sensitive.Step 4 Click Get IP Address.Step 5 When the access point’s IP address appears in the IP Address field, write it down.
CISCO CONFIDENTIAL - Draft 23-11Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 3 Configuring the Access Point for the First TimeAssigning an IP Address Using the CLIAssigning an IP Address Using the CLIWhen you connect the access point to the wired LAN, the access point links to the network using a bridge virtual interface (BVI) that it creates automatically. Instead of tracking separate IP addresses for the access point’s Ethernet and radio ports, the network uses the BVI.When you assign an IP address to the access point using the CLI, you must assign the address to the BVI. Beginning in privileged EXEC mode, follow these steps to assign an IP address to the access point’s BVI:Using a Telnet Session to Access the CLIFollow these steps to browse to access the CLI using a Telnet session. These steps are for a PC running Microsoft Windows with a Telnet terminal application. Check your PC operating instructions for detailed instructions for your operating system.Step 1 Select Start > Programs > Accessories > Telnet. If Telnet is not listed in your Accessories menu, select Start > Run, type Telnet in the entry field, and press Enter. Step 2 When the Telnet window appears, click Connect and select Remote System.Note In Windows 2000, the Telnet window does not contain drop-down menus. To start the Telnet session in Windows 2000, type open followed by the access point’s IP address.Step 3 In the Host Name field, type the access point’s IP address and click Connect.Command PurposeStep 1 configure terminal Enter global configuration mode.Step 2 interface bvi1 Enter interface configuration mode for the BVI.Step 3 ip address address maskAssign an IP address and address mask to the BVI. Note If you are connected to the access point using a Telnet session, you lose your connection to the access point when you assign a new IP address to the BVI. If you need to continue configuring the access point using Telnet, use the new IP address to open another Telnet session to the access point.
CISCO CONFIDENTIAL - Draft 23-12Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 3 Configuring the Access Point for the First TimeUsing a Telnet Session to Access the CLI
CHAPTER CISCO CONFIDENTIAL - Draft 24-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-014Using the Web-Browser InterfaceThis chapter describes the web-browser interface that you can use to configure the access point. It contains these sections:•Using the Web-Browser Interface for the First Time, page 4-2•Using the Management Pages in the Web-Browser Interface, page 4-2•Using Online Help, page 4-5The web-browser interface contains management pages that you use to change access point settings, upgrade firmware, and monitor and configure other wireless devices on the network.Note The access point web-browser interface is fully compatible with Microsoft Internet Explorer(version 5.x or later) or Netscape Navigator (version 4.x).
CISCO CONFIDENTIAL - Draft 24-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 4 Using the Web-Browser InterfaceUsing the Web-Browser Interface for the First TimeUsing the Web-Browser Interface for the First TimeUse the access point’s IP address to browse to the management system. See the “Obtaining and Assigning an IP Address” section on page 3-3 for instructions on assigning an IP address to the access point. Follow these steps to begin using the web-browser interface:Step 1 Start your Internet browser.Step 2 Enter the access point’s IP address in the browser Location field (Netscape Navigator) or Address field (Internet Explorer) and press Enter. An Enter Network Password screen appears. Step 3 Enter your username in the User Name field. The default username is Cisco. Step 4 Enter the access point password in the Password field and press Enter. The default password is Cisco. The access point Summary Status page appears. Using the Management Pages in the Web-Browser InterfaceThe system management pages use consistent techniques to present and save configuration information. A navigation bar is on the left side of the page, and configuration action buttons appear at the bottom. You use the navigation bar to browse to other management pages, and you use the configuration action buttons to save or cancel changes to the configuration. Note Changes are applied only when you click Apply. It’s important to remember that clicking your browser’s Back button returns you to the previous page without saving any changes you have made. Clicking Cancel cancels any changes you made on the page and keeps you on that page.
CISCO CONFIDENTIAL - Draft 24-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 4 Using the Web-Browser InterfaceUsing the Management Pages in the Web-Browser InterfaceFigure 4-1 shows the web-browser interface home page.Figure 4-1 Web-Browser Interface Home Page
CISCO CONFIDENTIAL - Draft 24-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 4 Using the Web-Browser InterfaceUsing the Management Pages in the Web-Browser InterfaceUsing Action ButtonsTable 4-1 lists the page links and buttons that appear on most management pages.Table 4-1 Common Buttons on Management PagesButton/Link DescriptionNavigation LinksHome Displays access point status page with information on the number of radio devices associated to the access point, the status of the Ethernet and radio interfaces, and a list of recent access point activity.Express Setup Displays the Express Setup page that is used to quickly configure basic access point settings such as system name, IP address, SNMP community, radio roles, and radio activation or deactivation.Express Security Displays the Express Security page that is used to quickly setup basic security settings for both radios such as SSID, VLAN, and the type of security.Network Map Displays a list of infrastructure devices on your wireless LAN.Association Displays a list of wireless devices associated to your access point, listing their system names, IP address, MAC address, parent-client relationships, and the VLAN.Network Interfaces Displays status and statistics for the Ethernet and radio interfaces and provides links to configuration pages for each interface.Security Displays a summary of security settings and provides links to security configuration pages that are used to configure all security options for each radio interface.Services Displays status for several access point features and links to configuration pages for Telnet/SSH, CDP, domain name server, filters, proxy Mobile IP, QoS, SNMP, SNTP, and VLANs.Wireless Services Displays a summary of wireless services used with CCKM and provides links to WDS configuration pages. .System Software Displays the version number of the firmware that the access point is running and provides links to configuration pages for upgrading and managing firmware.Event Log Displays the access point event log and provides links to configuration pages where you can select events to be included in traps, set event severity levels, and set notification methods.Configuration Action ButtonsApply Saves changes made on the page and remains on the page.Cancel Discards changes to the page and remains on the page.Clear Clears the selected options on the page.Refresh Updates status information or statistics displayed on a page.
CISCO CONFIDENTIAL - Draft 24-5Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 4 Using the Web-Browser InterfaceUsing Online HelpCharacter Restrictions in Entry FieldsBecause the access point uses Cisco IOS software, there are certain characters that you cannot use in the entry fields on the web-browser interface. Table 4-2 lists the prohibited characters and the fields in which you cannot use them.Using Online HelpClick the help icon at the top of any page in the web-browser interface to display online help. Figure 4-2 shows the help and print icons.Figure 4-2 Print and Help IconsWhen a help page appears in a new browser window, use the Select a topic drop-down menu to display the help index or instructions for common configuration tasks, such as configuring VLANs. Table 4-2 Prohibited Characters for Web-Browser Interface Entry FieldsEntry Field Type Prohibited CharactersPassword entry fields ?“$[+All other entry fields ?“$[+You also cannot use these three characters as the first character in an entry field:!#;
CISCO CONFIDENTIAL - Draft 24-6Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 4 Using the Web-Browser InterfaceUsing Online Help
CHAPTER CISCO CONFIDENTIAL - Draft 25-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-015Using the Command-Line InterfaceThis chapter describes the IOS command-line interface (CLI) that you can use to configure your access point. It contains these sections:•Cisco IOS Command Modes, page 5-2•Getting Help, page 5-3•Abbreviating Commands, page 5-3•Using no and default Forms of Commands, page 5-3•Understanding CLI Messages, page 5-4•Using Command History, page 5-4•Using Editing Features, page 5-5•Searching and Filtering Output of show and more Commands, page 5-8•Accessing the CLI, page 5-8
CISCO CONFIDENTIAL - Draft 25-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 5 Using the Command-Line InterfaceCisco IOS Command ModesCisco IOS Command ModesThe Cisco IOS user interface is divided into many different modes. The commands available to you depend on which mode you are currently in. Enter a question mark (?) at the system prompt to obtain a list of commands available for each command mode. Refer to the Cisco IOS Command Reference for Cisco Aironet Access Points and Bridges for a list of the supported Cisco IOS commands.When you start a session on the access point, you begin in user mode, often called user EXEC mode. Only a limited subset of the commands are available in user EXEC mode. For example, most of the user EXEC commands are one-time commands, such as show commands, which show the current configuration status, and clear commands, which clear counters or interfaces. The user EXEC commands are not saved when the access point reboots.To have access to all commands, you must enter privileged EXEC mode. Normally, you must enter a password to enter privileged EXEC mode. From this mode, you must enter privileged EXEC mode before you can enter the global configuration mode. Using the configuration modes (global, interface, and line), you can make changes to the running configuration. If you save the configuration, these commands are stored and used when the access point reboots. To access the various configuration modes, you must start at global configuration mode. From global configuration mode, you can enter interface configuration mode and line configuration mode.Table 5-1 describes the main command modes, how to access each one, the prompt you see in that mode, and how to exit the mode. The examples in the table use the host name ap.Table 5-1 Command Mode SummaryMode Access Method Prompt Exit Method About This ModeUser EXEC Begin a session with your access point.ap> Enter logout or quit. Use this mode to:•Change terminal settings•Perform basic tests•Display system informationPrivileged EXEC While in user EXEC mode, enter the enable command.ap# Enter disable to exit. Use this mode to verify commands. Use a password to protect access to this mode.Global configuration While in privileged EXEC mode, enter the configure command.ap(config)# To exit to privileged EXEC mode, enter exit or end, or press Ctrl-Z.Use this mode to configure parameters that apply to the entire access point.Interface configurationWhile in global configuration mode, enter the interface command (with a specific interface).ap(config-if)# To exit to global configuration mode, enter exit. To return to privileged EXEC mode, press Ctrl-Z or enter end.Use this mode to configure parameters for the Ethernet and radio interfaces. The 2.4-GHz radio is radio 0, and the 5-GHz radio is radio 1.
CISCO CONFIDENTIAL - Draft 25-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 5 Using the Command-Line InterfaceGetting HelpGetting HelpYou can enter a question mark (?) at the system prompt to display a list of commands available for each command mode. You can also obtain a list of associated keywords and arguments for any command, as shown in Table 5-2.Abbreviating CommandsYou have to enter only enough characters for the access point to recognize the command as unique. This example shows how to enter the show configuration privileged EXEC command:ap# show confUsing no and default Forms of CommandsMost configuration commands also have a no form. In general, use the no form to disable a feature or function or reverse the action of a command. For example, the no shutdown interface configuration command reverses the shutdown of an interface. Use the command without the keyword no to re-enable a disabled feature or to enable a feature that is disabled by default. Table 5-2 Help SummaryCommand Purposehelp Obtains a brief description of the help system in any command mode.abbreviated-command-entry?Obtains a list of commands that begin with a particular character string.For example:ap# di?dir disable disconnect abbreviated-command-entry<Tab> Completes a partial command name. For example:ap# sh conf<tab>ap# show configuration?Lists all commands available for a particular command mode. For example: ap> ?command ? Lists the associated keywords for a command. For example:ap> show ?command keyword ?Lists the associated arguments for a keyword.For example:ap(config)# cdp holdtime ? <10-255> Length of time (in sec) that receiver must keep this packet
CISCO CONFIDENTIAL - Draft 25-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 5 Using the Command-Line InterfaceUnderstanding CLI MessagesConfiguration commands can also have a default form. The default form of a command returns the command setting to its default. Most commands are disabled by default, so the default form is the same as the no form. However, some commands are enabled by default and have variables set to certain default values. In these cases, the default command enables the command and sets variables to their default values.Understanding CLI MessagesTable 5-3 lists some error messages that you might encounter while using the CLI to configure your access point.Using Command HistoryThe IOS provides a history or record of commands that you have entered. This feature is particularly useful for recalling long or complex commands or entries, including access lists. You can customize the command history feature to suit your needs as described in these sections:•Changing the Command History Buffer Size, page 5-4•Recalling Commands, page 5-5•Disabling the Command History Feature, page 5-5Changing the Command History Buffer SizeBy default, the access point records ten command lines in its history buffer. Beginning in privileged EXEC mode, enter this command to change the number of command lines that the access point records during the current terminal session: ap# terminal history [size number-of-lines]Table 5-3 Common CLI Error MessagesError Message Meaning How to Get Help% Ambiguous command: "show con"You did not enter enough characters for your access point to recognize the command.Re-enter the command followed by a question mark (?) with a space between the command and the question mark.The possible keywords that you can enter with the command are displayed.% Incomplete command. You did not enter all the keywords or values required by this command.Re-enter the command followed by a question mark (?) with a space between the command and the question mark.The possible keywords that you can enter with the command are displayed.% Invalid input detected at ‘^’ marker.You entered the command incorrectly. The caret (^) marks the point of the error.Enter a question mark (?) to display all the commands that are available in this command mode.The possible keywords that you can enter with the command are displayed.
CISCO CONFIDENTIAL - Draft 25-5Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 5 Using the Command-Line InterfaceUsing Editing FeaturesThe range is from 0 to 256.Beginning in line configuration mode, enter this command to configure the number of command lines the access point records for all sessions on a particular line:ap(config-line)# history [size number-of-lines]The range is from 0 to 256.Recalling CommandsTo recall commands from the history buffer, perform one of the actions listed in Table 5-4:Disabling the Command History FeatureThe command history feature is automatically enabled. To disable the feature during the current terminal session, enter the terminal no history privileged EXEC command. To disable command history for the line, enter the no history line configuration command.Using Editing FeaturesThis section describes the editing features that can help you manipulate the command line. It contains these sections:•Enabling and Disabling Editing Features, page 5-6•Editing Commands Through Keystrokes, page 5-6•Editing Command Lines that Wrap, page 5-7Table 5-4 Recalling CommandsAction11. The arrow keys function only on ANSI-compatible terminals such as VT100s.ResultPress Ctrl-P or the up arrow key. Recall commands in the history buffer, beginning with the most recent command. Repeat the key sequence to recall successively older commands.Press Ctrl-N or the down arrow key. Return to more recent commands in the history buffer after recalling commands with Ctrl-P or the up arrow key. Repeat the key sequence to recall successively more recent commands. show history While in privileged EXEC mode, list the last several commands that you just entered. The number of commands that are displayed is determined by the setting of the terminal history global configuration command and history line configuration command.
CISCO CONFIDENTIAL - Draft 25-6Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 5 Using the Command-Line InterfaceUsing Editing FeaturesEnabling and Disabling Editing FeaturesAlthough enhanced editing mode is automatically enabled, you can disable it.To re-enable the enhanced editing mode for the current terminal session, enter this command in privileged EXEC mode: ap# terminal editingTo reconfigure a specific line to have enhanced editing mode, enter this command in line configuration mode: ap(config-line)# editingTo globally disable enhanced editing mode, enter this command in line configuration mode: ap(config-line)# no editingEditing Commands Through KeystrokesTable 5-5 shows the keystrokes that you need to edit command lines.Table 5-5 Editing Commands Through KeystrokesCapability Keystroke1PurposeMove around the command line to make changes or corrections.Ctrl-B or the left arrow keyMove the cursor back one character. Ctrl-F or the right arrow keyMove the cursor forward one character. Ctrl-A Move the cursor to the beginning of the command line.Ctrl-E Move the cursor to the end of the command line.Esc B Move the cursor back one word.Esc F Move the cursor forward one word.Ctrl-T Transpose the character to the left of the cursor with the character located at the cursor.Recall commands from the buffer and paste them in the command line. The access point provides a buffer with the last ten items that you deleted.Ctrl-Y Recall the most recent entry in the buffer.Esc Y Recall the next buffer entry.The buffer contains only the last 10 items that you have deleted or cut. If you press Esc Y more than ten times, you cycle to the first buffer entry.Delete entries if you make a mistake or change your mind.Delete or Backspace Erase the character to the left of the cursor.Ctrl-D Delete the character at the cursor.Ctrl-K Delete all characters from the cursor to the end of the command line.Ctrl-U or Ctrl-X Delete all characters from the cursor to the beginning of the command line.Ctrl-W Delete the word to the left of the cursor.Esc D Delete from the cursor to the end of the word.
CISCO CONFIDENTIAL - Draft 25-7Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 5 Using the Command-Line InterfaceUsing Editing FeaturesEditing Command Lines that WrapYou can use a wraparound feature for commands that extend beyond a single line on the screen. When the cursor reaches the right margin, the command line shifts ten spaces to the left. You cannot see the first ten characters of the line, but you can scroll back and check the syntax at the beginning of the command. To scroll back to the beginning of the command entry, press Ctrl-B or the left arrow key repeatedly. You can also press Ctrl-A to immediately move to the beginning of the line.Note The arrow keys function only on ANSI-compatible terminals such as VT100s.In this example, the access-list global configuration command entry extends beyond one line. When the cursor first reaches the end of the line, the line is shifted ten spaces to the left and redisplayed. The dollar sign ($) shows that the line has been scrolled to the left. Each time the cursor reaches the end of the line, the line is again shifted ten spaces to the left. ap(config)# access-list 101 permit tcp 131.108.2.5 255.255.255.0 131.108.1ap(config)# $ 101 permit tcp 131.108.2.5 255.255.255.0 131.108.1.20 255.25ap(config)# $t tcp 131.108.2.5 255.255.255.0 131.108.1.20 255.255.255.0 eqap(config)# $108.2.5 255.255.255.0 131.108.1.20 255.255.255.0 eq 45 Capitalize or lowercase words or capitalize a set of letters.Esc C Capitalize at the cursor.Esc L Change the word at the cursor to lowercase.Esc U Capitalize letters from the cursor to the end of the word.Designate a particular keystroke as an executable command, perhaps as a shortcut.Ctrl-V or Esc QScroll down a line or screen on displays that are longer than the terminal screen can display.Note The More prompt appears for output that has more lines than can be displayed on the terminal screen, including show command output. You can use the Return and Space bar keystrokes whenever you see the More prompt. Return Scroll down one line.Space Scroll down one screen.Redisplay the current command line if the access point suddenly sends a message to your screen.Ctrl-L or Ctrl-R Redisplay the current command line.1. The arrow keys function only on ANSI-compatible terminals such as VT100s.Table 5-5 Editing Commands Through Keystrokes (continued)Capability Keystroke1Purpose
CISCO CONFIDENTIAL - Draft 25-8Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 5 Using the Command-Line InterfaceSearching and Filtering Output of show and more CommandsAfter you complete the entry, press Ctrl-A to check the complete syntax before pressing the Return key to execute the command. The dollar sign ($) appears at the end of the line to show that the line has been scrolled to the right:ap(config)# access-list 101 permit tcp 131.108.2.5 255.255.255.0 131.108.1$The software assumes you have a terminal screen that is 80 columns wide. If you have a width other than that, use the terminal width privileged EXEC command to set the width of your terminal.Use line wrapping with the command history feature to recall and modify previous complex command entries. For information about recalling previous command entries, see the “Editing Commands Through Keystrokes” section on page 5-6.Searching and Filtering Output of show and more CommandsYou can search and filter the output for show and more commands. This is useful when you need to sort through large amounts of output or if you want to exclude output that you do not need to see.To use this functionality, enter a show or more command followed by the pipe character (|), one of the keywords begin, include, or exclude, and an expression that you want to search for or filter out:command | {begin | include | exclude} regular-expressionExpressions are case sensitive. For example, if you enter | exclude output, the lines that contain output are not displayed, but the lines that contain Output are displayed.This example shows how to include in the output display only lines where the expression protocol appears:ap# show interfaces | include protocolVlan1 is up, line protocol is upVlan10 is up, line protocol is downGigabitEthernet0/1 is up, line protocol is downGigabitEthernet0/2 is up, line protocol is up Accessing the CLIYou can open the access point’s CLI using Telnet or Secure Shell (SSH). Opening the CLI with TelnetFollow these steps to open the CLI with Telnet. These steps are for a PC running Microsoft Windows with a Telnet terminal application. Check your PC operating instructions for detailed instructions for your operating system.Step 1 Select Start > Programs > Accessories > Telnet. If Telnet is not listed in your Accessories menu, select Start > Run, type Telnet in the entry field, and press Enter. Step 2 When the Telnet window appears, click Connect and select Remote System.
CISCO CONFIDENTIAL - Draft 25-9Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 5 Using the Command-Line InterfaceAccessing the CLINote In Windows 2000, the Telnet window does not contain drop-down menus. To start the Telnet session in Windows 2000, type open followed by the access point’s IP address.Step 3 In the Host Name field, type the access point’s IP address and click Connect.Step 4 At the username and password prompts, enter your administrator username and password. The default username is Cisco, and the default password is Cisco. The default enable password is also Cisco. Usernames and passwords are case-sensitive.Opening the CLI with Secure ShellSecure Shell Protocol is a protocol that provides a secure, remote connection to networking devices set up to use it. Secure Shell (SSH) is a software package that provides secure login sessions by encrypting the entire session. SSH features strong cryptographic authentication, strong encryption, and integrity protection. For detailed information on SSH, visit the homepage of SSH Communications Security, Ltd. at this URL: http://www.ssh.com/SSH provides more security for remote connections than Telnet by providing strong encryption when a device is authenticated. See the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points for detailed instructions on setting up the access point for SSH access.
CISCO CONFIDENTIAL - Draft 25-10Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 5 Using the Command-Line InterfaceAccessing the CLI
CHAPTER CISCO CONFIDENTIAL - Draft 26-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-016TroubleshootingThis chapter provides troubleshooting procedures for basic problems with the access point. For the most up-to-date, detailed troubleshooting information, refer to the Cisco TAC website at the following URL (select Product Support > Wireless > Wireless LAN):http://www.cisco.com/tac Sections in this chapter include:•Checking the Access Point LEDs, page 6-2•Checking Basic Settings, page 6-4•Resetting to the Default Configuration, page 6-9•Reloading the Access Point Image, page 6-10•Obtaining the Access Point Image File, page 6-13•Obtaining the TFTP Server Software, page 6-13•Running the Carrier Busy Test, page 6-8•Running the Ping/Link Test, page 6-8
CISCO CONFIDENTIAL - Draft 26-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingChecking the Access Point LEDsChecking the Access Point LEDsIf your access point is not working properly, check the Status LED on the top panel or the Ethernet and Radio LEDs in the cable bay area. You can use the LED indications to quickly assess the unit’s status. Figure 6-1 shows the access point LEDs. Figure 6-1 Access Point LEDs Note To view the Ethernet and Radio LEDs you must open the access point cover (refer to the “Opening the Access Point Cover” section on page 2-8). Note When the access point cover is opened, the Status LED colors are not visible.1Status LED 3Ethernet LED 2Access point cover 4Radio LED
CISCO CONFIDENTIAL - Draft 26-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingChecking the Access Point LEDsThe LED signals are listed in Table 6-1.Table 6-1 LED SignalsMessage typeCable Bay Area Top of UnitMeaningEthernet LED Radio LED Status LEDBoot loader status Green Green Green DRAM memory test ok.Off Blinking greenLight Blue Initialize Flash file system.Off Green Pink Flash memory test ok.Green Off Blue Ethernet test ok.Green Green Green Starting Cisco IOS.Association status n/a n/a Light green Normal operating condition, but no wireless client devices are associated with the unit. n/a n/a Sky blue Normal operating condition, at least one wireless client device is associated with the unit.Operating status Green n/a n/a Ethernet link is operational.Blinking greenn/a n/a Transmitting or receiving Ethernet packets.n/a Blinking greenn/a Transmitting or receiving radio packets.n/a n/a Blinkingdark blueSoftware upgrade in progressBoot loader warnings Off Off Yellow Ethernet link not operational.Red Off Yellow Ethernet failure.Amber Off Yellow Configuration recovery in progress(Mode button pressed for 2 to 3 seconds).Off Red Pink Image recovery(Mode button pressed for 20 to 30 seconds)Blinking greenBlinking red Blinking pinkImage recovery in progress and Mode button is released.
CISCO CONFIDENTIAL - Draft 26-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingChecking Basic SettingsChecking Basic SettingsMismatched basic settings are the most common causes of lost connectivity with wireless clients. If the access point does not communicate with client devices, check the following areas.SSIDWireless clients attempting to associate with the access point must use the same SSID as the access point. If a client device’s SSID does not match the SSID of an access point in radio range, the client device will not associate. The access point default SSID is tsunami.Boot loader errors Red Red Red DRAM memory test failure.Off Red Blinking red and blueFlash file system failure.Off Amber Blinking red and light blueEnvironment variable (ENVAR) failure.Amber Off Blinking red and yellowBad MAC address.Red Off Blinking red and offEthernet failure during image recovery.Amber Amber Blinking red and offBoot environment error.Red Amber Blinking red and offNo Cisco IOS image file.Amber Amber Blinking red and offBoot failure.Cisco IOS errors Blinking ambern/a n/a Transmit or receive Ethernet errors. n/a Blinking ambern/a Maximum retries or buffer full occurred on the radio.Red Red Orange Software failure; try disconnecting and reconnecting unit power.n/a n/a Orange General warning, insufficient inline power.Blinking greenBlinking greenBlinking greenUser activation of location indicator.Message typeCable Bay Area Top of UnitMeaningEthernet LED Radio LED Status LED
CISCO CONFIDENTIAL - Draft 26-5Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingLow Power ConditionWEP KeysThe WEP key you use to transmit data must be set up exactly the same on your access point and any wireless devices with which it associates. For example, if you set WEP Key 3 on your client adapter to 0987654321 and select it as the transmit key, you must also set WEP Key 3 on the access point to exactly the same value. The access point does not need to use Key 3 as its transmit key, however.Refer to the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points for instructions on setting the access point’s WEP keys.Security SettingsWireless clients attempting to authenticate with your access point must support the same security options configured in the access point, such as EAP or LEAP, MAC address authentication, Message Integrity Check (MIC), WEP key hashing, and 802.1X protocol versions.If a wireless client is unable to authenticate with your access point, contact the system administrator for proper security settings in the client adapter and for the client adapter driver and firmware versions that are compatible with the access point settings.Note The access point MAC address that appears on the Status page in the Aironet Client Utility (ACU) is the MAC address for the access point radio. The MAC address for the access point Ethernet port is printed on the label on the back of the access point.Low Power ConditionThe access point can be powered from the 48 VDC power module or from an in-line power source. The access point supports the IEEE 802.3af power standard and the Cisco CDP Power Negotiation protocol for in-line power sources. The access point requires more power (13 watts) than some legacy in-line power sources can supply. On power-up if the access point is unable to determine that the power source can supply sufficient power , the access point automatically enters low power mode and deactivates both radios to prevent an over-current condition. The access point also activates a Status LED low power error indication and creates an error log entry (see the “Checking the Access Point LEDs” section on page 6-2 a nd “Inline Power Status Messages” section on page 6-6).WarningThis product must be connected to an IEC60950 compliant limited power source or a power-over-ethernet (PoE) IEEE 802.3af compliant power source. On power up, the access point boots up in low power mode, Cisco IOS software loads and runs, CDP power negotiation determines if sufficient power is available. If there is sufficient power then the radios are turned on, otherwise the radios remain disabled.When the access point is in low power mode, the Cisco IOS show interfaces dot11radio 0 command produces the following results:Dot11Radio0 is up, line protocol is down.
CISCO CONFIDENTIAL - Draft 26-6Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingLow Power ConditionCDP Inline Power NegotiationThe access point uses CDP (Cisco Discovery Protocol) to negotiate with the in-line power source for sufficient power. The results of these negotiations will either be a decision to enter full power mode or to remain in low power mode. Independent of the CDP negotiations, the access point hardware uses the 802.3af classification scheme to report maximum power is required by the access point. Currently, Cisco switches (802.3af capable) do not support CDP in-line power negotiation. The access point automatically enters normal power mode if a Cisco Catalyst 3550, 3560, or 3570 switch is detected in the received CDP ID field. When the access point determins that sufficient power is not available for normal power mode an error message is logged and the Status LED turns orange to indicate the low power mode ((see the “Checking the Access Point LEDs” section on page 6-2 and the “Inline Power Status Messages” section on page 6-6) .Inline Power Status MessagesThese messages are logged by the access point to report the power condition:•%CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source—This message indicates the access point is using the power module and can support full power.•%CDP_PD-4-POWER_OK: Full power - NO_CDP_NON_CISCO inline power source—This message indicates the access point is operating at full power but is connected to a non-Cisco in-line power source. To prevent possible over-current conditions, this must be an IEEE 802.3af compliant power source or an IEC60950 compliant limited power source.•%CDP_PD-4-POWER_OK: Full power - HIGH_POWER_CLASSIC inline power source—This message indicates the access point is operating at full power and has detected a Cisco switch capable of supplying sufficient power.•%CDP_PD-4-POWER_OK: Full power - MIDSPAN inline power source—This message indicates the access point is operating at full power and the Cisco IOS power in-line negotiation command has been used to indicate a power injector is being used to supply power. •%CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source—This message indicates the access point is operating at full power and power is being supplied by a Cisco switch capable of power negotiation.•%CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC inline power source platform=AIR-AP1120B-A-K9 MAC address=xxxx.xxxx.xxxx—This message indicates the access point is in low power mode with all radios disabled and the power source is not capable of in-line power negotiations. The xxxx.xxxx.xxxx indicates the MAC address of the power source.•%CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED inline power source platform=AIR-AP1120B-A-K9 MAC address=xxxx.xxxx.xxxx—This message indicates the access point is in low power mode with all radios disabled and the power source is incapable of supplying sufficient power. The xxxx.xxxx.xxxx indicates the MAC address of the power source.
CISCO CONFIDENTIAL - Draft 26-7Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingLow Power ConditionInline Power ExceptionCDP in-line power negotiation is dependent on similar code being resident in the Cisco switch that is providing power. However, not every switch supports this CDP power negotiation code. As a work around for such pre-standard switches the following Cisco IOS CLI command is required:(config)# [no] power inline negotiation {prestandard source | injector H.H.H}You can use this Cisco IOS CLI command to inform the access point that the power source is an 802.3af compliant Cisco switch or that a power injector is being used to supply sufficient power. Refer to Table 6-2 for information on when to use this special Cisco IOS command.Caution If the access point receives power through Power-over-Ethernet (PoE), the output current of the power sourcing equipment (PSE) cannot exceed 400 mA or 1500 V per port, whichever is smaller. The power source must comply with IEEE802.3af or IEC60950 for limited power sources.Issuing the Cisco IOS CommandFollow these steps to issue the Cisco IOS command for your power scenario:Step 1 Connect a PC to the access point console port and use a terminal emulator to establish a session with the access point (refer to the “Connecting to the Access Point Locally” section on page 3-3).Step 2 From the Privileged EXEC mode (refer to the “Cisco IOS Command Modes” section on page 5-2), enter one of these commands that applies to your power configuration (see Table 6-2):•power inline negotiation injector xxxx.xxxx.xxxx (where xxxx.xxxx.xxxx is the MAC address of the switch port to which the access point is connected.•power inline negotiation prestandard sourceStep 3 Enter the write memory command to save the setting to the access point memory.Step 4 Enter the quit command to exit the terminal session.Table 6-2 Special Cisco IOS CommandPower Source Cisco IOS CommandAC power module None requiredPower injector11. Power injector must be AIR-PWRINJ3 or AIR-PWRINJ-FIB.For Cisco non-802.3af compliant switches and Cisco switches without inline power, use this Cisco IOS command:power inline negotiation injector xxxx.xxxx.xxxx (where xxxx.xxxx.xxxx is the MAC address of the switch port to which the access point is connected.Cisco 802.3af compliant switch22. If command 2 is not issued when powered only by a Cisco non-802.3af compliant switch, the access point powers up with both radio interfaces down.Use this Cisco IOS command:power inline negotiation prestandard source
CISCO CONFIDENTIAL - Draft 26-8Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingRunning the Carrier Busy TestRunning the Carrier Busy TestYou can use the carrier busy test to determine the least conjested channel for a radio interface (802.11g or 802.11a). You should typically run the test several times over several days to obtain the best results and to avoid temporary activity spikes.Note The carrier busy test is primarily used for single access points or bridge environments. For sites with multiple access points, a site survey is typically performed to determine the best operation location and operating frequency for the access points. Note All associated clients on the selected radio will be deassociated during the 6 to 8 seconds needed for the carrier busy test. Perform these steps to activate the carrier busy test:Step 1 Use your web browser to access the access point browser interface.Step 2 Click Network Interfaces and the Network Interface Summary screen appears.Step 3 Choose the radio interface experiencing problems by clicking Radio0-802.11G or Radio1-802.11A. The respective radio status page appears.Step 4 Click the Carrier Busy Test tab and the Carrier Busy Test screen appearsStep 5 Click Start to begin the carrier busy test.When the test completes, the results are displayed on the screen. For each of the channel center frequencies, the test produces a value indicating the percentage of time that the channel is busy. Running the Ping/Link TestYou can use the ping or link test to evaluate the link to and from an associated wireless device. The ping or link test provides two modes of operation:a. Perform a test using a specified number of packets and then display the test results.b. Perform a test that continuously operates until you stop the test and then displays the test results.Perform these steps to activate the ping or link test:Step 1 Use your web browser to access the access point browser interface.Step 2 Click Association and the main association page appears.Step 3 Click the MAC address of an associated wireless device and the Statistics page for that device appears.Step 4 Click the Ping/Link Test tab and the Ping/Link Test page appears.
CISCO CONFIDENTIAL - Draft 26-9Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingResetting to the Default ConfigurationStep 5 If you want to specify the number of packets to use in the test, perform these steps:a. Enter the desired number of packets in the Number of Packets fieldb. Enter the desired packet size in the Packet Size field.c. Click Start.Step 6 If you want to use a continuous test, perform these steps:a. Enter the desired packet size in the Packet Size field.b. Click Start to activate the test.c. When desired, click Stop to stop the test.When the test has completed, the test results are displayed at the bottom of the page. You should check for any lost packets that can indicate a possible problem with the wireless link. For best results, you should also perform this test several times.Resetting to the Default ConfigurationIf you forget the password that allows you to configure the access point, you may need to completely reset the configuration. You can use the MODE button on the access point or the web-browser interface.Note The following steps reset all configuration settings to factory defaults, including passwords, WEP keys, the IP address, and the SSID. Using the MODE ButtonFollow these steps to delete the current configuration and return all access point settings to the factory defaults using the MODE button:Step 1 Open the access point cover (refer to the “Opening the Access Point Cover” section on page 2-8).Step 2 Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.Step 3 Press and hold the MODE button while you reconnect power to the access point.Step 4 Hold the MODE button until the Ethernet LED turns an amber color (approximately 2 to 3 seconds), and release the button.Step 5 After the access point reboots, you must reconfigure the access point by using the Web browser interface, the Telnet interface, or Cisco IOS commands.Note The access point is configured with the factory default values including the IP address (set to receive an IP address using DHCP).
CISCO CONFIDENTIAL - Draft 26-10Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingReloading the Access Point ImageUsing the Web Browser InterfaceFollow these steps to delete the current configuration and return all access point settings to the factory defaults using the web browser interface.Step 1 Open your Internet browser. You must use Microsoft Internet Explorer (version 5.x or later) or Netscape Navigator (version 4.x).Step 2 Enter the access point’s IP address in the browser address line and press Enter. An Enter Network Password screen appears.Step 3 Enter your username in the User Name field.Step 4 Enter the access point password in the Password field and press Enter. The Summary Status page appears.Step 5 Click System Software and the System Software screen appears.Step 6 Click System Configuration and the System Configuration screen appears.Step 7 Click the Reset to Defaults button.Note If the access point is configured with a static IP address, the IP address does not change.Step 8 After the access point reboots, you must reconfigure the access point by using the Web browser interface, the Telnet interface, or Cisco IOS commands.Reloading the Access Point ImageIf your access point has a firmware failure, you must reload the complete access point image file using the Web browser interface or by pressing and holding the MODE button for around 30 seconds. You can use the browser interface if the access point firmware is still fully operational and you want to upgrade the firmware image. However, you can use the MODE button when the access point has a corrupt firmware image.
CISCO CONFIDENTIAL - Draft 26-11Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingReloading the Access Point ImageUsing the MODE ButtonYou can use the MODE button on the access point to reload the access point image file from an active Trivial File Transfer Protocol (TFTP) server on your network or on a PC connected to the access point Ethernet port. Note If your access point experiences a firmware failure or a corrupt firmware image, indicated by the Status LED turning an orange color, you must reload the image from a connected TFTP server.Note This process resets all configuration settings to factory defaults, including passwords, WEP keys, the access point IP address, and SSIDs. Follow these steps to reload the access point image file:Step 1 The PC you intend to use must be configured with a static IP address between 10.0.0.2 and 10.0.0.30.Step 2 Place a copy of the access point image file (such as c1130-k9w7-tar.122-15.JA.tar) into the TFTP server folder on your PC. For additional information, refer to the “Obtaining the Access Point Image File” and “Obtaining the TFTP Server Software” sections. Step 3 Rename the access point image file in the TFTP server folder to c1130-k9w7-tar.default. Step 4 Activate the TFTP server.Step 5 If using in-line power, use a Category 5 (CAT5) Ethernet cable to connect your PC to the To Network Ethernet connector on the power injector.Step 6 Open the access point cover (refer to the “Opening the Access Point Cover” section on page 2-8).Step 7 Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.Step 8 Press and hold the MODE button while you reconnect power to the access point.Step 9 Hold the MODE button until the Radio LED turns a red color (approximately 20 to 30 seconds), and release the MODE button.Step 10 After the access point reboots, you must reconfigure the access point by using the Web interface, the Telnet interface, or Cisco IOS commands.
CISCO CONFIDENTIAL - Draft 26-12Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingReloading the Access Point ImageWeb Browser InterfaceYou can also use the Web browser interface to reload the access point image file. The Web browser interface supports loading the image file using HTTP or TFTP interfaces. Note Your access point configuration is not changed when using the browser to reload the image file.Browser HTTP InterfaceThe HTTP interface enables you to browse to the access point image file on your PC and download the image to the access point. Follow these instructions to use the HTTP interface:Step 1 Open your Internet browser. You must use Microsoft Internet Explorer (version 5.x or later) or Netscape Navigator (version 4.x).Step 2 Enter the access point’s IP address in the browser address line and press Enter. An Enter Network Password screen appears.Step 3 Enter your username in the User Name field.Step 4 Enter the access point password in the Password field and press Enter. The Summary Status page appears.Step 5 Click the System Software tab and then click Software Upgrade. The HTTP Upgrade screen appears.Step 6 Click the Browse button to locate the access point image file (such as c1130-k9w7-tar.122-15.JA.tar) on your PC.Step 7 Click the Upload button.For additional information, click the Help icon on the Software Upgrade screen. Browser TFTP InterfaceThe TFTP interface allows you to use a TFTP server on a network device to load the access point image file. Follow these instructions to use a TFTP server:Step 1 Open your Internet browser. You must use Microsoft Internet Explorer (version 5.x or later) or Netscape Navigator (version 4.x).Step 2 Enter the access point’s IP address in the browser address line and press Enter. An Enter Network Password screen appears.Step 3 Enter your username in the User Name field.Step 4 Enter the access point password in the Password field and press Enter. The Summary Status page appears.Step 5 Click the System Software tab and then click Software Upgrade. The HTTP Upgrade screen appears.Step 6 Click the TFTP Upgrade tab. Step 7 Enter the IP address for the TFTP server in the TFTP Server field.
CISCO CONFIDENTIAL - Draft 26-13Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingObtaining the Access Point Image FileStep 8 Enter the file name for the access point image file (such as c1130-k9w7-tar.122-15.JA.tar) in the Upload New System Image Tar File field. If the file is located in a subdirectory of the TFTP server root directory, include the relative path of the TFTP server root directory with the filename. If the file is located in the TFTP root directory, enter only the filename.Step 9 Click the Upload button.Step 10 When a message appears that indicates the upgrade is complete, click OK.For additional information click the Help icon on the Software Upgrade screen. Obtaining the Access Point Image FileThe access point image file can be obtained from the Cisco.com software center using these steps:Step 1 Use your Internet browser to access the Cisco Software Center at the following URL:http://www.cisco.com/public/sw-center/sw-wireless.shtmlStep 2 Click Option 2: Aironet Wireless Software Display Tables.Step 3 Find the access point firmware and utilities section and click Cisco Aironet 1130 Series (Cisco IOS Software).Step 4 Click on the access point image file, such as c1130-k9w7-tar.122-15.JA.tar. Step 5 On the Encryption Authorization Form, enter the requested information, read the encryption information, and check the boxes that apply.Step 6 Click Submit.Step 7 Read and accept the terms and conditions of the Software License Agreement.Step 8 Select the image file again to download it.Step 9 Download and save the image file to your hard drive and then exit the Internet browser. Obtaining the TFTP Server SoftwareYou can download TFTP server software from several web sites. Cisco recommends the shareware TFTP utility available at this URL:http://tftpd32.jounin.netFollow the instructions on the website for installing and using the utility.
CISCO CONFIDENTIAL - Draft 26-14Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Chapter 6 TroubleshootingObtaining the TFTP Server Software
CISCO CONFIDENTIAL - Draft 2A-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01APPENDIXATranslated Safety WarningsThis appendix provides translations of the safety warnings that appear in this publication. These translated warnings apply to other documents in which they appear in English. The following safety warnings appear in this appendix:•Statement 245B—Explosive Device Proximity Warning, page A-2•Statement 332—Antenna Installation Warning, page A-3•Statement 1001—Work During Lightning Activity Warning, page A-4•Statement 1004—Installation Instructions Warning, page A-5•Statement 1005—Circuit Breaker (15A) Warning, page A-6
CISCO CONFIDENTIAL - Draft 2A-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix A Translated Safety WarningsStatement 245B—Explosive Device Proximity WarningStatement 245B—Explosive Device Proximity WarningWarningDo not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. Statement 245BWaarschuwingGebruik dit draadloos netwerkapparaat alleen in de buurt van onbeschermde ontstekers of in een omgeving met explosieven indien het apparaat speciaal is aangepast om aan de eisen voor een dergelijk gebruik te voldoen.VaroitusÄlä käytä johdotonta verkkolaitetta suojaamattomien räjäytysnallien läheisyydessä tai räjäytysalueella, jos laitetta ei ole erityisesti muunnettu sopivaksi sellaiseen käyttöön. AttentionNe jamais utiliser un équipement de réseau sans fil à proximité d'un détonateur non blindé ou dans un lieu présentant des risques d'explosion, sauf si l'équipement a été modifié à cet effet.WarnungBenutzen Sie Ihr drahtloses Netzwerkgerät nicht in der Nähe ungeschützter Sprengkapseln oder anderer explosiver Stoffe, es sei denn, Ihr Gerät wurde eigens für diesen Gebrauch modifiziert und bestimmt.AvvertenzaNon utilizzare la periferica di rete senza fili in prossimità di un detonatore non protetto o di esplosivi a meno che la periferica non sia stata modificata a tale proposito.AdvarselIkke bruk den trådløse nettverksenheten nært inntil uisolerte fenghetter eller i et eksplosivt miljø med mindre enheten er modifisert slik at den tåler slik bruk.AvisoNão opere o dispositivo de rede sem fios perto de cápsulas explosivas não protegidas ou num ambiente explosivo, a não ser que o dispositivo tenha sido modificado para se qualificar especialmente para essa utilização.¡Advertencia!No utilizar un aparato de la red sin cable cerca de un detonador que no esté protegido ni tampoco en un entorno explosivo a menos que el aparato haya sido modificado con ese fin.Varning!Använd inte den trådlösa nätverksenheten i närheten av oskyddade tändhattar eller i en explosiv miljö om inte enheten modifierats för att kunna användas i sådana sammanhang.
CISCO CONFIDENTIAL - Draft 2A-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix A Translated Safety WarningsStatement 332—Antenna Installation WarningStatement 332—Antenna Installation Warning WarningIn order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches (20 cm) or more from the body of all persons. Statement 332WaarschuwingOm te voldoen aan de FCC radiofrequentie (RF) blootstellingslimieten dienen antennes zich minstens 20 cm of meer van de lichamen van alle personen bevinden.VaroitusFCC:n antamien radiotaajuuksille altistumista koskevien rajoitusten mukaan antennien on sijaittava vähintään 20 cm:n päässä kaikista henkilöistä.AttentionPour se conformer aux limites d'exposition à la fréquence radio préconisées par la FCC (Federal Communications Commission), les antennes doivent se situer à un minimum de 20 cm de toute personne.WarnungUm die in den FCC-Richtlinien festgelegten Expositionshöchstgrenzen für Radiofrequenzen (RF) nicht zu überschreiten, sollten Antennen mindestens 20 cm entfernt von Personen aufgestellt werden.AvvertenzaPer conformarsi ai limiti FCC di esposizione a radiofrequenza (RF), le antenne devono stare ad una distanza minima di 20 cm dal corpo di ogni persona.AdvarselI henhold til eksponeringsgrensene for radiofrekvenser (RF), skal antenner befinne seg på en avstand av minst 20 cm eller mer fra mennesker.AvisoPara estar de acordo com as normas FCC de limites de exposição para freqüência de rádio (RF), as antenas devem estar distantes no mínimo 20 cm (7,9 pol) do corpo de qualquer pessoa.¡Advertencia!Para cumplir con los límites de exposición de radio frecuencia (RF) de la Comisión Federal de Comunicaciones (FCC) es preciso ubicar las antenas a un mínimo de 20 cm (7,9 pulgadas) o más del cuerpo de las personas.Varning!För att följa FCC-exponeringsgränserna för radiofrekvens (RF), bör antenner placeras på minst 20 cm avstånd från alla människor.
CISCO CONFIDENTIAL - Draft 2A-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix A Translated Safety WarningsStatement 1001—Work During Lightning Activity WarningStatement 1001—Work During Lightning Activity WarningWarningDo not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001WaarschuwingTijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan te sluiten of te ontkoppelen. VaroitusÄlä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita ukkosilmalla.AttentionNe pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage.WarnungArbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen Sie keine ab, wenn es gewittert.AvvertenzaNon lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.AdvarselUtfør aldri arbeid på systemet, eller koble kabler til eller fra systemet når det tordner eller lyner.AvisoNão trabalhe no sistema ou ligue e desligue cabos durante períodos de mau tempo (trovoada).¡Advertencia!No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas eléctricas en la atmósfera.Varning!Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla loss kablar.
CISCO CONFIDENTIAL - Draft 2A-5Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix A Translated Safety WarningsStatement 1004—Installation Instructions WarningStatement 1004—Installation Instructions WarningWarningRead the installation instructions before connecting the system to the power source. Statement 1004WaarschuwingRaadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.VaroitusLue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.AttentionAvant de brancher le système sur la source d'alimentation, consulter les directives d'installation.WarnungVor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen.AvvertenzaConsultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.AdvarselLes installasjonsinstruksjonene før systemet kobles til strømkilden.AvisoLeia as instruções de instalação antes de ligar o sistema à fonte de energia.¡Advertencia!Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.Varning!Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten.
CISCO CONFIDENTIAL - Draft 2A-6Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix A Translated Safety WarningsStatement 1005—Circuit Breaker (15A) WarningStatement 1005—Circuit Breaker (15A) WarningWarningThis product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 15A Statement 1005WaarschuwingDit product is afhankelijk van de installatie van het gebouw voor beveiliging tegen kortsluiting (overstroom). Controleer of de beschermingsinrichting niet meer dan: 15A is.VaroitusTämä tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, että suojalaitteen mitoitus ei ole yli: 15A AttentionPour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de l'installation électrique du local. Vérifiez que le courant nominal du dispositif de protection n'est pas supérieur à : 15A WarnungDieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der Schutzvorrichtung nicht mehr als: 15A beträgt.AvvertenzaQuesto prodotto dipende dall'impianto dell'edificio per quanto riguarda la protezione contro cortocircuiti (sovracorrente). Assicurarsi che il dispositivo di protezione non abbia un rating superiore a: 15AAdvarselDette produktet er avhengig av bygningens installasjoner av kortslutnings (overstrøm)-beskyttelse. Påse at verneenheten ikke er merket høyere enn: 15A AvisoEste produto depende das instalações existentes para proteção contra curto-circuito (sobrecarga). Assegure-se de que o fusível ou disjuntor não seja superior a: 15A ¡Advertencia!Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del edificio. Asegúrese de que el dispositivo de protección no sea superior a: 15A Varning!Denna produkt är beroende av i byggnaden installerat kortslutningsskydd (överströmsskydd). Kontrollera att skyddsanordningen inte har högre märkvärde än: 15A15A
CISCO CONFIDENTIAL - Draft 2A-7Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix A Translated Safety WarningsStatement 1005—Circuit Breaker (15A) Warning15A 15A15A
CISCO CONFIDENTIAL - Draft 2A-8Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix A Translated Safety WarningsStatement 1005—Circuit Breaker (15A) Warning
CISCO CONFIDENTIAL - Draft 2B-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01APPENDIXBDeclarations of Conformity and Regulatory InformationThis appendix provides declarations of conformity and regulatory information for the Cisco Aironet 1130 Series Access Points. This appendix contains the following sections:•Manufacturers Federal Communication Commission Declaration of Conformity Statement•Department of Communications—Canada•European Community, Switzerland, Norway, Iceland, and Liechtenstein•Declaration of Conformity for RF Exposure•Guidelines for Operating Cisco Aironet Access Points in Japan
CISCO CONFIDENTIAL - Draft 2B-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix B Declarations of Conformity and Regulatory InformationManufacturers Federal Communication Commission Declaration of Conformity StatementManufacturers Federal Communication Commission Declaration of Conformity StatementModel:AIR-AP1131AG-A-K9 FCC Certification number: LDK102054Manufacturer:Cisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAThis device complies with Part 15 rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:•Reorient or relocate the receiving antenna.•Increase separation between the equipment and receiver.•Connect the equipment to an outlet on a circuit different from which the receiver is connected.•Consult the dealer or an experienced radio/TV technician.Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device.Caution Within the 5.15 to 5.25 GHz band (5 GHz radio channels 34 to 48) the U-NII devices are restricted to indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System (MSS) operations.Tested To ComplyWith FCC StandardsFOR HOME OR OFFICE USE
CISCO CONFIDENTIAL - Draft 2B-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix B Declarations of Conformity and Regulatory InformationDepartment of Communications—CanadaDepartment of Communications—CanadaModel:AIR-AP1131AG-A-K9 Certification number: 2461B-102054Canadian Compliance StatementThis Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference that may cause undesired operation.Cisco Aironet 2.4-GHz Access Points are certified to the requirements of RSS-210 for 2.4-GHz spread spectrum devices, and Cisco Aironet 54-Mbps, 5-GHz Access Points are certified to the requirements of RSS-210 for 5-GHz spread spectrum devices.The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office.European Community, Switzerland, Norway, Iceland, and LiechtensteinModel:AIR-AP1131AG-E-K9 Declaration of Conformity with Regard to the R&TTE Directive 1999/5/ECEnglish: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Deutsch: Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren entsprecheneden Vorgaben der Richtlinie 1999/5/EU.Dansk: Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante bestemmelser i Directiv 1999/5/EF.
CISCO CONFIDENTIAL - Draft 2B-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix B Declarations of Conformity and Regulatory InformationEuropean Community, Switzerland, Norway, Iceland, and LiechtensteinFor 2.4 GHz radios, the following standards were applied:•Radio: EN 300.328-1, EN 300.328-2•EMC: EN 301.489-1, EN 301.489-17•Safety: EN 60950Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance.For 54 Mbps, 5 GHz access points, the following standards were applied:•Radio: EN 301.893•EMC: EN 301.489-1, EN 301.489-17•Safety: EN 60950Español: Este equipo cumple con los requisitos esenciales asi como con otras disposiciones de la Directive 1999/5/EC.Έλληνας: Αυτός ο εξοπλισµός συµµορφώνεται µε τις ουσιώδεις απαιτήσεις και τις λοιπές διατάξεις της Οδηγίας 1999/5/EΚ.Français: Cet appareil est conforme aux exigencies essentialles et aux autres dispositions pertinantes de la Directive 1999/5/EC.Íslenska: Þessi búnaður samrýmist lögboðnum kröfum og öðrum ákvæðum tilskipunar 1999/5/ESB.Italiano: Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti dalla Direttiva 1999/5/EC.Nederlands: Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijn 1999/5/EC.Norsk: Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser i EU-directiv 1999/5/EC.Português: Este equipamento satisfaz os requisitos essenciais e outras provisões da Directiva 1999/5/EC.Suomalainen: Tämä laite täyttää direktiivin 1999/5/EY oleelliset vaatimukset ja on siinä asetettujen muidenkin ehtojen mukainen.Svenska: Denna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i Direktiv 1999/5/EC.
CISCO CONFIDENTIAL - Draft 2B-5Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix B Declarations of Conformity and Regulatory InformationDeclaration of Conformity for RF ExposureThe following CE mark is affixed to the access point with a 2.4 GHz radio and a 54 Mbps, 5 GHz radio:Declaration of Conformity for RF ExposureThe radio has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices as defined in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. The equipment shoud be installed more than 20 cm (7.9 in.) from your body or nearby persons.The access point must be installed to maintain a minimum 20 cm (7.9 in.) co-located separation distance from other FCC approved indoor/outdoor antennas used with the access point. Any antennas or transmitters not approved by the FCC cannot be co-located with the access point. The access point’s co-located 2.4 GHz and 5 GHz integrated antennas support a minimum separation distance of8 cm (3.2 in.) and are compliant with the applicable FCC RF exposure limit when transmitting simultaneously.Note Dual antennas used for diversity operation are not considered co-located.49325
CISCO CONFIDENTIAL - Draft 2B-6Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix B Declarations of Conformity and Regulatory InformationGuidelines for Operating Cisco Aironet Access Points in JapanGuidelines for Operating Cisco Aironet Access Points in JapanThis section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English.Model:AIR-AP1131AG-J-K9 Japanese TranslationEnglish TranslationThis equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines.1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity.2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions.3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below.Contact Number: 03-5549-650003-5549-650043768
CISCO CONFIDENTIAL - Draft 2B-7Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix B Declarations of Conformity and Regulatory InformationDeclaration of Conformity StatementsDeclaration of Conformity StatementsAll the Declaration of Conformity statements related to this product can be found at the following URL:http://www.ciscofax.com
CISCO CONFIDENTIAL - Draft 2B-8Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix B Declarations of Conformity and Regulatory InformationDeclaration of Conformity Statements
CISCO CONFIDENTIAL - Draft 2C-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01APPENDIXCAccess Point Specifications This appendix provides technical specifications for the Cisco Aironet 1130AG Series Access Point. Table C-1 lists the technical specifications for the access point. Table C-1 Access Point SpecificationsCategory 802.11b Radio Specifications 802.11g Radio Specifications 802.11a Radio SpecificationsSize 7.53 in. W x 7.53 in. D x 1.31 in. H19.13 cm W x 19.13 cm D x 3.33 cm H Indicators Tri-color Status LED indicator on the top panel and two bi-color LED indicators (radio and Ethernet) in the cable bayConnectors Cable bay (left to right)Power connector (for plug-in AC power module); RJ-45 connector for 10BASE-T or 100BASE-T Ethernet connections; upside down RJ-45 connector for serial connections.Input Voltage 48 VDC (nominal)Input Power 12.95 W (typical)Operating Temperature Base unit:32 to 104oF (0 to 40oC) 1130 series power injector:32 to 104oF (0 to 40oC)1130 series power module:32 to 104oF (0 to 40oC)Storage Temperature TBD to TBDoF (TBD to TBDoC) Weight Without mounting hardware:1.48 lbs (0.67 kg)
CISCO CONFIDENTIAL - Draft 2C-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix C Access Point SpecificationsPower Output 100 mW (20 dBm)50 mW (17 dBm)25 mW (14 dBm)10 mW (11 dBm)5 mW (8 dBm)3 mW (5 dBm)1 mW (2 dBm)0.5 mW (-1 dBm)(Depending on the regulatory domain in which the access point is installed)50 mW (17 dBm)25 mW (14 dBm)10 mW (11 dBm)5 mW (8 dBm)3 mW (5 dBm)1 mW (2 dBm)0.5 mW (-1 dBm)(Depending on the regulatory domain in which the access point is installed)50 mW (17 dBm)30 mW (15 dBm)25 mW (14 dBm)10 mW (11 dBm)5 mW (8 dBm)3 mW (5 dBm)1 mW (2 dBm)0.5 mW (-1 dBm)(Depending on the regulatory domain in which the access point is installed)Antenna A diversity system with two integrated 4-dBi antennas. A diversity system with two integrated 4-dBi antennas. Frequency 2.400 to 2.497 GHz (Depending on the regulatory domain in which the access point is installed)5.15 to 5.25 GHz5.25 to 5.35 GHz5.725 to 5.85 GHz(Depending on the regulatory domain in which the access point is installed)Modulation Complementary Code Keying (CCK)Orthogonal Frequency Division Multiplex (OFDM)Subcarrier modulation BPSK (1 Mbps)QPSK (2 Mbps)CCK (5.5 and 11 Mbps)BPSK (6 and 9 Mbps)QPSK (12 and 18 Mbps)16-QAM (24 and 36 Mbps)64-QAM (48 and 54 Mbps)BPSK (6 Mbps and 9 Mbps)QPSK (12 Mbps and 18 Mbps)16-QAM (24 and 36 Mbps)64-QAM (48 and 54 Mbps)Data rates 1, 2, 5.5, and 11 Mbps 6, 9, 12, 18, 24, 36, 48, and 54 MbpsTypical indoor range 320 ft at 1 Mbps 130 ft at 11 Mbps 170 ft at 6 Mbps 80 ft at 54 Mbps 175 ft at 6 Mbps 50 ft at 54 Mbps Compliance Complies with UL 2043 for products installed in a building’s environmental air handling spaces, such as above suspended ceilings.Caution Only the fiber-optic power injector (AIR-PWRINJ-FIB) has been tested to UL 2043 for operation in a building’s environmental air space; the AIR-PWRINJ3 power injector and the power module are not tested to UL 2043 and should not be placed in a building’s environmental air space, such as above suspended ceilings.Safety Designed to meet:•CSN/CSA 22.2 No. 60950•UL 2043 (Plenum rating)•UL 60950 Third Edition•IEC 60950 Second Edition, including Amendments 1-4 with all deviations•EN 60950 Second Edition, including Amendments 1-4Table C-1 Access Point Specifications (continued)Category 802.11b Radio Specifications 802.11g Radio Specifications 802.11a Radio Specifications
CISCO CONFIDENTIAL - Draft 2C-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix C Access Point SpecificationsRadio Approvals FCC Parts 15.247Canada RSS-210Japan ARIB-STD-33BJapan ARIB-STD-66Europe EN-300.328FCC Part 15.407Canada RSS-210Japan ARIB STD-T71EN 301.893EMI and Susceptibility FCC Part 15.107 and 15.109 Class BICES-003 Class B (Canada)EN 55022 BAS/NZS 3548 Class BVCCI Class BEN 301.489-1EN 301.489-17RF Exposure OET-65CRSS-102ANSI C95.1Table C-1 Access Point Specifications (continued)Category 802.11b Radio Specifications 802.11g Radio Specifications 802.11a Radio Specifications
CISCO CONFIDENTIAL - Draft 2C-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix C Access Point Specifications
CISCO CONFIDENTIAL - Draft 2D-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01APPENDIXDChannels and Power LevelsThis appendix lists the IEEE 802.11b/g (2.4-GHz) and the IEEE 802.11a (5-GHz) channels and maximum power levels supported by the world’s regulatory domains. The following topic is covered in this appendix:•Channels and Maximum Power Levels, page D-2
CISCO CONFIDENTIAL - Draft 2D-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix D Channels and Power LevelsChannels and Maximum Power LevelsChannels and Maximum Power Levels IEEE 802.11b/g (2.4-GHz Band)An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. Table D-1 indicates the channel identifiers, channel center frequencies, and maximum power levels for each channel allowed by the regulatory domains:.Table D-1 Channels and Maximum Conducted Power for the 802.11b/g Radio Channel IdentifierCenter Frequency(MHz)Maximum Conducted Power Levels (dBm) in the Regulatory DomainsAmericas(–A)China(–C)EMEA(–E)Japan(–J)North American(–N)CCK OFDM CCK OFDM CCK OFDM CCK OFDM CCK OFDM1 2412 201714141414141420172 2417 201714141414141420173 2422 201714141414141420174 2427 201714141414141420175 2432 201714141414141420176 2437 201714141414141420177 2442 201714141414141420178 2447 201714141414141420179 2452 2017141414141414201710 2457 20 17 14 14 14 14 14 14 20 1711 2462 20 17 14 14 14 14 14 14 20 1712 2467 – – 14 14 14 14 14 14 – –13 2472 – – 14 14 14 14 14 14 – –14 2484 – – – – – – 14 – – –
CISCO CONFIDENTIAL - Draft 2D-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix D Channels and Power LevelsChannels and Maximum Power LevelsIEEE 802.11a (5-GHz Band)An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. All channel sets are restricted to indoor usage except the Americas (–A), which allows for indoor and outdoor use on channels 52 through 64 in the United States.Table D-2 indicates the channel identifiers, channel center frequencies, and maximum power levels for each IEEE 802.11a 20-MHz-wide channel allowed by the regulatory domains:.Table D-2 Channels for IEEE 802.11a RadioChannel IdentifierCenter Frequency(MHz)Maximum Conducted Power Levels (dBm) in the Regulatory DomainsAmericas(–A)China(–C)EMEA(–E)Japan(–J)North America(–N)UNII-1 (5150-5250 MHz)34 5170 – – – 15 –36 5180 15 – 17 – 1538 5190 – – – 15 –40 5200 15 – 17 – 1542 5210 – – – 15 –44 5220 15 – 17 – 1546 5230 – – – 15 –48 5240 15 – 17 15UNII-2 (5250-5350 MHz)52 5260 17 – 17 – 1756 5280 17 – 17 – 1760 5300 17 – 17 – 1764 5320 17 – 17 – 17UNII-3 (5725-5850 MHz)149 5745 17 17 – – 17153 5765 17 17 – – 17157 5785 17 17 – – 17161 5805 17 17 – – 171655825–––––
CISCO CONFIDENTIAL - Draft 2D-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix D Channels and Power LevelsChannels and Maximum Power Levels
CISCO CONFIDENTIAL - Draft 2E-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01APPENDIXEConsole Cable PinoutsThis appendix identifies the pinouts for the serial console cable that connects to the access point’s serial console port. The appendix contains the following sections:•Overview, page E-2•Console Port Signals and Pinouts, page E-2
CISCO CONFIDENTIAL - Draft 2E-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01Appendix E Console Cable PinoutsOverviewOverviewThe access point requires a special serial cable that connects the access point serial console port (RJ-45 connector) to your PC’s COM port (DB-9 connector). This cable can be purchased from Cisco (part number AIR-CONCAB1200) or can be built using the pinouts in this appendix. Console Port Signals and PinoutsUse the console RJ-45 to DB-9 serial cable to connect the access point’s console port to the COM port of your PC running a terminal emulation program.Note Both the Ethernet and console ports use RJ-45 connectors. Be careful to avoid accidently connecting the serial cable to the Ethernet port connector. Table E-1 lists the signals and pinouts for the console RJ-45 to DB-9 serial cable. Table E-1 Signals and Pinouts for a Console RJ-45 to DB-9 Serial CableConsole Port PC COM PortRJ-45 DB-9Pins Signals1, 2, 3, 41. NC indicates not connected.2. TXD indicates transmit data.3. GND indicates ground.4. RXD indicates receive data.Pins Signals1, 2, 3, 41NC ––2NC ––3 TXD 2 RXD4GND 5GND5GND 5GND6 RXD 3 TXD7NC ––8NC ––
CISCO CONFIDENTIAL - Draft 2GL-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01GLOSSARY802.11 The IEEE standard that specifies carrier sense media access control and physical layer specifications for 1- and 2-megabit-per-second (Mbps) wireless LANs operating in the 2.4-GHz band.802.11a The IEEE standard that specifies carrier sense media access control and physical layer specifications for wireless LANs operating in the 5-GHz frequency band.802.11b The IEEE standard that specifies carrier sense media access control and physical layer specifications for 5.5- and 11-Mbps wireless LANs operating in the 2.4-GHz frequency band.802.11g The IEEE standard that specifies carrier sense media access control and physical layer specifications for 6, 9, 12, 18, 24, 36, 48, and 54 Mbps wireless LANs operating in the 2.4-GHz frequency band.Aaccess point A wireless LAN data transceiver that uses radio waves to connect a wired network with wireless stations.ad hoc network A wireless network composed of stations without Access Points.antenna gain The gain of an antenna is a measure of the antenna’s ability to direct or focus radio energy over a region of space. High gain antennas have a more focused radiation pattern in a specific direction.associated A station is configured properly to allow it to wirelessly communicate with an Access Point.Bbeacon A wireless LAN packet that signals the availability and presence of the wireless device. Beacon packets are sent by access points and base stations; however, client radio cards send beacons when operating in computer to computer (Ad Hoc) mode.BOOTP Boot Protocol. A protocol used for the static assignment of IP addresses to devices on the network.
CISCO CONFIDENTIAL - Draft 2GlossaryGL-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01BPSK A modulation technique used by IEEE 802.11b-compliant wireless LANs for transmission at 1 Mbps.broadcast packet A single data message (packet) sent to all addresses on the same subnet.CCCK Complementary code keying. A modulation technique used by IEEE 802.11b-compliant wireless LANs for transmission at 5.5 and 11 Mbps.cell The area of radio range or coverage in which the wireless devices can communicate with the base station. The size of the cell depends upon the speed of the transmission, the type of antenna used, and the physical environment, as well as other factors.client A radio device that uses the services of an Access Point to communicate wirelessly with other devices on a local area network.CSMA Carrier sense multiple access. A wireless LAN media access method specified by the IEEE 802.11 specification.Ddata rates The range of data transmission rates supported by a device. Data rates are measured in megabits per second (Mbps).dBi A ratio of decibels to an isotropic antenna that is commonly used to measure antenna gain. The greater the dBi value, the higher the gain, and the more acute the angle of coverage.DHCP Dynamic host configuration protocol. A protocol available with many operating systems that automatically issues IP addresses within a specified range to devices on the network. The device retains the assigned address for a specific administrator-defined period.dipole A type of low-gain (2.2-dBi) antenna consisting of two (often internal) elements.Domain Name The text name that refers to a grouping of networks or network resources based on organization-type or geography; for example: name.com—commercial; name.edu—educational; name.gov—government; ISPname.net—network provider (such as an ISP); name.ar—Argentina; name.au—Australia; and so on.DNS Domain Name System server. A server that translates text names into IP addresses. The server maintains a database of host alphanumeric names and their corresponding IP addresses.DSSS Direct sequence spread spectrum. A type of spread spectrum radio transmission that spreads its signal continuously over a wide frequency band.
CISCO CONFIDENTIAL - Draft 2GlossaryGL-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01EEAP Extensible Authentication Protocol. An optional IEEE 802.1x security feature ideal for organizations with a large user base and access to an EAP-enabled Remote Authentication Dial-In User Service (RADIUS) server.Ethernet The most widely used wired local area network. Ethernet uses carrier sense multiple access (CSMA) to allow computers to share a network and operates at 10, 100, or 1000 Mbps, depending on the physical layer used.Ffile server A repository for files so that a local area network can share files, mail, and programs.firmware Software that is programmed on a memory chip.Ggateway A device that connects two otherwise incompatible networks together.GHz Gigahertz. One billion cycles per second. A unit of measure for frequency.IIEEE Institute of Electrical and Electronic Engineers. A professional society serving electrical engineers through its publications, conferences, and standards development activities. The body responsible for the Ethernet 802.3 and wireless LAN 802.11 specifications.infrastructure The wired Ethernet network.IP Address The Internet Protocol (IP) address of a station.IP subnet mask The number used to identify the IP subnetwork, indicating whether the IP address can be recognized on the LAN or if it must be reached through a gateway. This number is expressed in a form similar to an IP address; for example: 255.255.255.0.isotropic An antenna that radiates its signal in a spherical pattern.
CISCO CONFIDENTIAL - Draft 2GlossaryGL-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01MMAC Media Access Control address. A unique 48-bit number used in Ethernet data packets to identify an Ethernet device, such as an access point or your client adapter.modulation Any of several techniques for combining user information with a transmitter’s carrier signal.multipath The echoes created as a radio signal bounces off of physical objects.multicast packet A single data message (packet) sent to multiple addresses.Oomni-directional This typically refers to a primarily circular antenna radiation pattern.Orthogonal Frequency Division Multiplex (OFDM)A modulation technique used by IEEE 802.11a-compliant wireless LANs for transmission at 6, 9, 12, 18, 24, 36, 48, and 54 Mbps.Ppacket A basic message unit for communication across a network. A packet usually includes routing information, data, and sometimes error detection information.QQuadruple Phase Shift Keying A modulation technique used by IEEE 802.11b-compliant wireless LANs for transmission at 2 Mbps.Rrange A linear measure of the distance that a transmitter can send a signal.receiver sensitivity A measurement of the weakest signal a receiver can receive and still correctly translate it into data.RF Radio frequency. A generic term for radio-based technology.
CISCO CONFIDENTIAL - Draft 2GlossaryGL-5Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01roaming A feature of some Access Points that allows users to move through a facility while maintaining an unbroken connection to the LAN.RP-TNC A connector type unique to Cisco Aironet radios and antennas. Part 15.203 of the FCC rules covering spread spectrum devices limits the types of antennas that may be used with transmission equipment. In compliance with this rule, Cisco Aironet, like all other wireless LAN providers, equips its radios and antennas with a unique connector to prevent attachment of non-approved antennas to radios.Sspread spectrum A radio transmission technology that spreads the user information over a much wider bandwidth than otherwise required in order to gain benefits such as improved interference tolerance and unlicensed operation.SSID Service Set Identifier (also referred to as Radio Network Name). A unique identifier used to identify a radio network and which stations must use to be able to communicate with each other or to an access point. The SSID can be any alphanumeric entry up to a maximum of 32 characters.Ttransmit power The power level of radio transmission.UUNII Unlicensed National Information Infrastructure—regulations for UNII devices operating in the 5.15 to 5.35 GHz and 5.725 to 5.825 GHz frequency bands.UNII-1 Regulations for UNII devices operating in the 5.15 to 5.25 GHz frequency band.UNII-2 Regulations for UNII devices operating in the 5.25 to 5.35 GHz frequency band.UNII-3 Regulations for UNII devices operating in the 5.725 to 5.825 GHz frequency band.unicast packet A single data message (packet) sent to a specific IP address.WWEP Wired Equivalent Privacy. An optional security mechanism defined within the 802.11 standard designed to make the link integrity of wireless devices equal to that of a cable.workstation A computing device with an installed client adapter.
CISCO CONFIDENTIAL - Draft 2GlossaryGL-6Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01
CISCO CONFIDENTIAL - Draft 2IN-1Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01INDEXAabbreviating commands 5-3access point image 6-10antennaconnectors C-2Apply button 4-4Bbasic settings, checking 6-4CCancel button 4-4Cisco TAC 6-1CLIabbreviating commands 5-3command modes 5-2editing featuresenabling and disabling 5-6keystroke editing 5-6wrapped lines 5-7error messages 5-4filtering command output 5-8getting help 5-3historychanging the buffer size 5-4described 5-4disabling 5-5recalling commands 5-5no and default forms of commands 5-3terminal emulator settings 3-4command-line interfaceSee CLIcommand modes 5-2commandsabbreviating 5-3no and default 5-3connectors C-1, C-2console port E-2Ddata rates C-2declarations of conformity B-1default, configuration, resetting 6-9default commands 5-3Eediting featuresenabling and disabling 5-6keystrokes used 5-6wrapped lines 5-7EIRP, maximum D-2 to ??, D-3 to ??error messages, during command entry 5-4extended temperature range 2-3, 2-4FFCC Declaration of Conformity B-2FCC Safety Compliance 2-2filteringshow and more command output 5-8frequencies D-2, D-3
CISCO CONFIDENTIAL - Draft 2IndexIN-2Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01frequency range C-2Gglobal configuration mode 5-2Hhelp, for the command line 5-3historychanging the buffer size 5-4described 5-4disabling 5-5recalling commands 5-5Home button 4-4Iindicators 6-2input power C-1installation guidelines 2-3interface configuration mode 5-2IP address, finding and setting 3-10IPSU 3-9Kkey features 1-2MMAC 3-10management options, CLI 5-1Mode button 6-11modulation C-2Nno commands 5-3OOK button 4-4operating temperature C-1Ppackage contents 2-3password reset 6-9pinouts, serial cable E-2powerconnecting 2-17input C-1output C-2power level, maximum D-2privileged EXEC mode 5-2Rrange, radio C-2regulatorydomains D-2, D-3regulatory information B-1reloading access point image 6-10RF exposure B-5Ssafety warnings, translated A-1serialcable E-2Cisco cable E-2size C-1SSH Communications Security, Ltd. 5-9
CISCO CONFIDENTIAL - Draft 2IndexIN-3Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01status indicators C-1storage temperature C-1TTAC 6-1Telnet 3-11temperatureoperating C-1storage C-1terminal emulator 3-4TFTP server 6-11troubleshooting 6-1Uunpacking 2-3user EXEC mode 5-2Vvoltage range C-1Wwarnings 2-2, A-1Web-based interfacecommon buttons 4-4compatible browsers 4-1web site, Cisco Software Center 3-9, 6-13weight C-1WEP key 6-5
CISCO CONFIDENTIAL - Draft 2IndexIN-4Cisco Aironet 1130AG Series Access Point Hardware Installation GuideOL-6226-01

Navigation menu