Cisco Systems 102059 RM 23A 802.11a Wireless LAN Module User Manual 125h tl
Cisco Systems Inc RM 23A 802.11a Wireless LAN Module 125h tl
manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 632902 |
| Application ID | DkYZA9PEHWbfUsedGgyGNQ== |
| Document Description | manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 71.57kB (894673 bits) |
| Date Submitted | 2006-03-02 00:00:00 |
| Date Available | 2006-08-25 00:00:00 |
| Creation Date | 2006-02-23 13:36:52 |
| Producing Software | Acrobat Distiller 6.0.1 (Windows) |
| Document Lastmod | 2006-02-23 16:51:42 |
| Document Title | 125h_tl.fm |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | jdugas |
CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1250AG Series Access Point Hardware Installation Guide June 2006 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Text Part Number: OL-8247-01 CISCO CONFIDENTIAL - Draft 1 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense. You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: • Turn the television or radio antenna until the interference stops. • Move the equipment to one side or the other of the television or radio. • Move the equipment farther away from the television or radio. • Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.) Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0601R) Cisco Aironet 1250AG Series Access Point Hardware Installation Guide © 2006 Cisco Systems, Inc. All rights reserved. CISCO CONFIDENTIAL - Draft 1 C H A P T E R Overview Cisco Aironet 1250AG Series Access Points combine mobility, flexibility, and modularity with the enterprise-class features required by networking professionals. With a management system based on Cisco IOS software software, the 1250AG series access point is a Wi-Fi certified, wireless LAN transceiver. The access point supports two radio modules: a 2.4-GHz radio (IEEE 802.11b/g) and a 5-GHz radio (IEEE 802.11a). The modular design enables support for a future IEEE802.11n radio module once the standard is ratified. This modularity helps customers future proof their access point investments. You can configure the radios separately, using different settings on each. The access point connects wireless and wired networks or is the center point of a stand-alone wireless network. In large installations, wireless users within radio range of an access point can roam throughout a facility while maintaining seamless, uninterrupted access to the network. You can configure and monitor the access point using the command-line interface (CLI), the browser-based management system, Simple Network Management Protocol (SNMP), or Cisco Structured Wireless-Aware Network (SWAN). This chapter provides information on the following topics: • Hardware Features, page 1-2 • Network Configuration Examples, page 1-7 Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 1-1 Chapter 1 Overview Hardware Features CISCO CONFIDENTIAL - Draft 1 Hardware Features Key hardware features of the access point include: • Dual-radio operation with radio modules (see page 1-4) • Ethernet port (see page 1-5) • Console port (see page 1-5) • LEDs, (see page 1-5) • Multiple power sources (see page 1-5) • UL 2043 certification (see page 1-6) • Anti-theft features (see page 1-6) Refer to Appendix C, “Access Point Specifications,” for a list of access point specifications. Figure 1-2 shows the access point with two radio modules. Figure 1-1 Access Point with 802.11b/g and 802.11a Radio Modules Cisco Aironet 1250AG Series Access Point Hardware Installation Guide 1-2 OL-8247-01 Chapter 1 Overview Hardware Features CISCO CONFIDENTIAL - Draft 1 Figure 1-2 illustrates the 2.4-GHz radio module. Figure 1-2 2.4 GHz Radio Module 2.4-GHz antenna connector (left) 2.4-GHz antenna connector (right/primary) Figure 1-3 illustrates the 5-GHz radio module. Figure 1-3 5-GHz Radio Module 5-GHz antenna connector (left) 5-GHz antenna connector (right/primary) Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 1-3 Chapter 1 Overview Hardware Features CISCO CONFIDENTIAL - Draft 1 Single or Dual-Radio Operation The access point supports single or simultaneous dual radio operation using 2.4-GHz 802.11b/g radio and 5-GHz 802.11a radio modules. Each radio uses dual-diversity integrated antennas. A blank module is supported for single radio access point configurations. The access point supports upgrading of a radio module with a 802.11n radio module (future availability). The 802.11n radio module will be available when the standard is ratified. The 5-GHz radio incorporates an Unlicensed National Information Infrastructure (UNII) radio transceiver operating in the UNII 5-GHz frequency bands. The 802.11g radio is called Radio0 and the 802.11a radio is called Radio1. Note In Cisco IOS Release 12.3(8)JA and later, the access point radios are disabled by default, and there is no default SSID. You must create an SSID and enable the radios before the access point allows wireless associations from other devices. Antennas Supported Table 1-1 lists the supported access point antennas. Caution Table 1-1 The access point, the antennas, and the power source (power injector or power module) must be located in an indoor environment. Supported Antennas 2.4-GHz Antennas AIR-ANT5959 diversity ceiling omnidirectional Gain (dBi) 5-GHz Antennas Gain (dBi) AIR-ANT5135D-R articulated omnidirectional 3.5 4.5 AIR-ANT4941 articulated dipole 2.2 AIR-ANT5145V-R diversityceiling omnidirectional AIR-ANT1728 ceiling omnidirectional 5.2 AIR-ANT5160V-R omnidirectional AIR-ANT2506 mast mount omnidirectional 5.2 AIR-ANT5170P-R diversity wall patch directional AIR-ANT3213 diversity pillar omnidirectional 5.2 AIR-ANT5195P-R wall patch directional AIR-ANT1729 wall patch directional AIR-ANT2460P-R patch directional AIR-ANT2465P-R diversity patch directional 6.5 AIR-ANT2012 diversity patch directional 6.5 AIR-ANT3549 patch directional AIR-ANT2490P-R patch directional AIR-ANT2410Y-R yagi directional 10 9.5 Cisco Aironet 1250AG Series Access Point Hardware Installation Guide 1-4 OL-8247-01 Chapter 1 Overview Hardware Features CISCO CONFIDENTIAL - Draft 1 Ethernet Port The auto-sensing Ethernet port (see Figure TBD ) accepts an RJ-45 connector, linking the access point to your 10BASE-T, 100BASE-T, or 1000BASE-T Ethernet LAN. The access point can receive power through the Ethernet cable from a power injector, switch, or power patch panel. The Ethernet MAC address is printed on the label on the back of the access point (refer to the “Locating the Product Serial Number” section on page -viii). Console Port The serial console port provides access to the access point’s command-line interface (CLI) using a terminal emulator program. The port is located on the end of the unit (see Figure 1-2). Use an RJ-45 to DB-9 serial cable to connect your computer’s COM port to the access point’s serial console port. (Refer to Appendix E, “Console Cable Pinouts,” for a description of the console port pinouts.) Assign the following port settings to a terminal emulator to open the management system pages: 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control. Note After completing your configuration changes, you must remove the serial cable from the access point. LEDs The access point has three LEDs (see Figure 1-2) to indicate Ethernet activity, radio activity, and status indications (refer to the “Checking the Access Point LEDs” section on page 6-2 for additional information). • The Status LED provides general operating status and error indications. • The Ethernet LED signals Ethernet traffic on the wired Ethernet LAN and provides Ethernet error indications. • The Radio LED signals that wireless packets are being transmitted or received over the radio interface and provides error indications. Power Sources The access point can receive power from an external power module or from inline power using the Ethernet cable. The access point supports the IEEE 802.3af inline power standard and Cisco CDP Power Negotiation. Using inline power, you do not need to run a power cord to the access point because power is supplied over the Ethernet cable. Warning This product must be connected to a Power over Ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. Statement 353 The access point supports the following power sources: • Power module • Inline power: – Cisco Aironet 1250 Series Power Injector ( (AIR-PWRINJ3 or AIR-PWRINJ-FIB) – An inline power capable switch, such as the Cisco Catalyst 3550 PWR XL, 3560-48PS, 3570-48PS, 4500 with 802.3AF PoE module, or the 6500 with 802.3AF PoE module Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 1-5 Chapter 1 Overview Hardware Features CISCO CONFIDENTIAL - Draft 1 – Other inline power switches supporting the IEEE 802.3af inline power standard Note Some switches and patch panels might not provide enough power to operate the access point with both 2.4-GHz and 5-GHz radios. At power-up, if the access point is unable to determine that the power source can supply sufficient power, the access point automatically deactivates both radios to prevent an over-current condition. The access point also activates a Status LED low power error indication and creates an error log entry (refer to the “Checking the Access Point LEDs” section on page 6-2 and the “Low Power Condition” section on page 6-5). UL 2043 Certification The access point has adequate fire resistance and low smoke-producing characteristics suitable for operation in a building's environmental air space, such as above suspended ceilings, in accordance with Section 300-22(c) of the NEC, and with Sections 2-128, 12-010(3) and 12-100 of the Canadian Electrical Code, Part 1, C22.1. Caution Only the fiber-optic power injector (AIR-PWRINJ-FIB) has been tested to UL 2043 for operation in a building’s environmental air space; the AIR-PWRINJ3 power injector and the power module are not tested to UL 2043 and should not be placed in a building’s environmental air space, such as above suspended ceilings. Anti-Theft Features TBD Cisco Aironet 1250AG Series Access Point Hardware Installation Guide 1-6 OL-8247-01 Chapter 1 Overview Network Configuration Examples CISCO CONFIDENTIAL - Draft 1 Network Configuration Examples This section describes the access point’s role in three common wireless network configurations. The access point’s default configuration is as a root unit connected to a wired LAN or as the central unit in an all-wireless network. The repeater role requires a specific configuration. Root Unit on a Wired LAN An access point connected directly to a wired LAN provides a connection point for wireless users. If more than one access point is connected to the LAN, users can roam from one area of a facility to another without losing their connection to the network. Figure 1-4 shows access points acting as root units on a wired LAN. Figure 1-4 Access Points as Root Units on a Wired LAN Access point 135445 Access point Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 1-7 Chapter 1 Overview Network Configuration Examples CISCO CONFIDENTIAL - Draft 1 Repeater Unit that Extends Wireless Range An access point can be configured as a stand-alone repeater to extend the range of your infrastructure or to overcome an obstacle that blocks radio communication. The repeater forwards traffic between wireless users and the wired LAN by sending packets to either another repeater or to an access point connected to the wired LAN. The data is sent through the route that provides the best performance for the client. Figure 1-5 shows an access point acting as a repeater. Consult the Cisco IOS Software Configuration Guide for Cisco Aironet Access Points for instructions on setting up an access point as a repeater. Note Non-Cisco client devices might have difficulty communicating with repeater access points. Figure 1-5 Access Point as Repeater Repeater 135444 Access point Cisco Aironet 1250AG Series Access Point Hardware Installation Guide 1-8 OL-8247-01 Chapter 1 Overview Network Configuration Examples CISCO CONFIDENTIAL - Draft 1 Central Unit in an All-Wireless Network In an all-wireless network, an access point acts as a stand-alone root unit. The access point is not attached to a wired LAN; it functions as a hub linking all stations together. The access point serves as the focal point for communications, increasing the communication range of wireless users. Figure 1-6 shows an access point in an all-wireless network. Figure 1-6 Access Point as Central Unit in All-Wireless Network 135443 Access point Bridge Network with Wireless Clients The access point supports root bridge and non-root bridge roles used to interconnect a remote LAN to the main LAN (see Figure 1-7). The bridge units can also support wireless clients. Root Bridge and Non-root Bridge with Clients 135446 Figure 1-7 Root bridge Non-root bridge Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 1-9 Chapter 1 Overview Network Configuration Examples CISCO CONFIDENTIAL - Draft 1 Workgroup Bridge Network The access point supports a workgroup bridge role to interconnect remote Ethernet workstations to the main LAN. The workgroup bridge can communicate with an access point (see Figure 1-8) or with a bridge (see Figure 1-9). Figure 1-8 Workgroup Bridge Communicating with an Access Point 135448 Access point Workgroup bridge Workgroup Bridge Communicating with a Bridge Bridge Workgroup bridge 135499 Figure 1-9 Cisco Aironet 1250AG Series Access Point Hardware Installation Guide 1-10 OL-8247-01 Chapter 1 Overview Network Configuration Examples CISCO CONFIDENTIAL - Draft 1 Point-to-Point Bridge Configuration In a point-to-point bridge configuration, two bridges interconnect two LAN networks using a wireless communication link (see Figure 1-10). The bridge connected to the main LAN network is classified as a root bridge and the other bridge is classified as a non-root bridge. Point-to-Point Bridge Configuration 117029 Figure 1-10 Root bridge Non-root bridge Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 1-11 Chapter 1 Overview Network Configuration Examples CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1250AG Series Access Point Hardware Installation Guide 1-12 OL-8247-01 CISCO CONFIDENTIAL - Draft 1 A P P E N D I X Declarations of Conformity and Regulatory Information This appendix provides declarations of conformity and regulatory information for the Cisco Aironet 1250 Series Access Point and the Cisco Aironet 1250 Series Lightweight Access Point. This appendix contains the following sections: • Manufacturers Federal Communication Commission Declaration of Conformity Statement, page B-2 • Department of Communications—Canada, page B-3 • European Community, Switzerland, Norway, Iceland, and Liechtenstein, page B-3 • Declaration of Conformity for RF Exposure, page B-6 • Guidelines for Operating Cisco Aironet Access Points in Japan, page B-7 • Administrative Rules for Cisco Aironet Access Points in Taiwan, page B-8 • Declaration of Conformity Statements, page B-10 • Declaration of Conformity Statements for European Union Countries, page B-10 Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 B-1 Appendix B Manufacturers Federal Communication Commission Declaration of Conformity Statement Declarations of Conformity and Regulatory Information CISCO CONFIDENTIAL - Draft 1 Manufacturers Federal Communication Commission Declaration of Conformity Statement Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Models Certification Numbers AIR-RM23A-A-K9 LDK102059 AIR-RM23G-A-K9 LDK102060 Manufacturer: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference. However, there is no guarantee that interference will not occur. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures: Caution • Reorient or relocate the receiving antenna. • Increase separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from which the receiver is connected. • Consult the dealer or an experienced radio/TV technician. The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device. Cisco Aironet 1250AG Series Access Point Hardware Installation Guide B-2 OL-8247-01 Appendix B Declarations of Conformity and Regulatory Information Department of Communications—Canada CISCO CONFIDENTIAL - Draft 1 Caution Within the 5.15 to 5.25 GHz band (5 GHz radio channels 34 to 48) the U-NII devices are restricted to indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System (MSS) operations. Department of Communications—Canada Models Certification Numbers AIR-RM23A-A-K9 2461B-102059 AIR-RM23G-A-K9 2461B-102060 Canadian Compliance Statement This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada. This device complies with Class B Limits of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Cisco Aironet 2.4-GHz Access Points are certified to the requirements of RSS-210 for 2.4-GHz spread spectrum devices, and Cisco Aironet 54-Mbps, 5-GHz Access Points are certified to the requirements of RSS-210 for 5-GHz spread spectrum devices.The use of this device in a system operating either partially or completely outdoors may require the user to obtain a license for the system according to the Canadian regulations. For further information, contact your local Industry Canada office. European Community, Switzerland, Norway, Iceland, and Liechtenstein Models AIR-RM23A-E-K9 AIR-RM23G-E-K9 Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 B-3 Appendix B Declarations of Conformity and Regulatory Information European Community, Switzerland, Norway, Iceland, and Liechtenstein CISCO CONFIDENTIAL - Draft 1 Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC Cisco Aironet 1250AG Series Access Point Hardware Installation Guide B-4 OL-8247-01 Appendix B Declarations of Conformity and Regulatory Information European Community, Switzerland, Norway, Iceland, and Liechtenstein CISCO CONFIDENTIAL - Draft 1 For 2.4 GHz radios, the following standards were applied: Note • Radio: EN 300.328-1, EN 300.328-2 • EMC: EN 301.489-1, EN 301.489-17 • Safety: EN 60950 This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate Compliance. Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 B-5 Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity for RF Exposure CISCO CONFIDENTIAL - Draft 1 For 54 Mbps, 5 GHz access points, the following standards were applied: • Radio: EN 301.893 • EMC: EN 301.489-1, EN 301.489-17 • Safety: EN 60950 The following CE mark is affixed to the access point with a 2.4 GHz radio and a 54 Mbps, 5 GHz radio: Declaration of Conformity for RF Exposure The radio has been found to be compliant to the requirements set forth in CFR 47 Sections 2.1091, and 15.247 (b) (4) addressing RF Exposure from radio frequency devices as defined in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. The equipment shoud be installed more than 20 cm (7.9 in.) from your body or nearby persons. The access point must be installed to maintain a minimum 20 cm (7.9 in.) co-located separation distance from other FCC approved indoor/outdoor antennas used with the access point. Any antennas or transmitters not approved by the FCC cannot be co-located with the access point. The access point’s co-located 2.4 GHz and 5 GHz integrated antennas support a minimum separation distance of 8 cm (3.2 in.) and are compliant with the applicable FCC RF exposure limit when transmitting simultaneously. Note Dual antennas used for diversity operation are not considered co-located. Cisco Aironet 1250AG Series Access Point Hardware Installation Guide B-6 OL-8247-01 Appendix B Declarations of Conformity and Regulatory Information Guidelines for Operating Cisco Aironet Access Points in Japan CISCO CONFIDENTIAL - Draft 1 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English. 03-5549-6500 43768 Japanese Translation English Translation This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines. 1. Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity. 2. If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions. 3. If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below. Contact Number: 03-5549-6500 Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 B-7 Appendix B Declarations of Conformity and Regulatory Information Administrative Rules for Cisco Aironet Access Points in Taiwan CISCO CONFIDENTIAL - Draft 1 Administrative Rules for Cisco Aironet Access Points in Taiwan This section provides administrative rules for operatingCisco Aironet access points inTaiwan. The rules are provided in both Chinese and English. Access Points with IEEE 802.11a Radios Chinese Translation English Translation This equipment is limited for indoor use. Cisco Aironet 1250AG Series Access Point Hardware Installation Guide B-8 OL-8247-01 Appendix B Declarations of Conformity and Regulatory Information Administrative Rules for Cisco Aironet Access Points in Taiwan CISCO CONFIDENTIAL - Draft 1 All Access Points Chinese Translation English Translation Administrative Rules for Low-power Radio-Frequency Devices Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions. Article 14 The operation of the low-power radio-frequency devices is subject to the conditions that no harmful interference is caused to aviation safety and authorized radio station; and if interference is caused, the user must stop operating the device immediately and can't re-operate it until the harmful interference is clear. The authorized radio station means a radio-communication service operating in accordance with the Communication Act. The operation of the low-power radio-frequency devices is subject to the interference caused by the operation of an authorized radio station, by another intentional or unintentional radiator, by industrial, scientific and medical (ISM) equipment, or by an incidental radiator. Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 B-9 Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity Statements CISCO CONFIDENTIAL - Draft 1 Declaration of Conformity Statements All the Declaration of Conformity statements related to this product can be found at the following URL: http://www.ciscofax.com Declaration of Conformity Statements for European Union Countries The Declaration of Conformity statement for the European Union countries is listed below: ----- TBD------ Cisco Aironet 1250AG Series Access Point Hardware Installation Guide B-10 OL-8247-01 Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity Statements for European Union Countries CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 B-11 Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity Statements for European Union Countries CISCO CONFIDENTIAL - Draft 1 Cisco Aironet 1250AG Series Access Point Hardware Installation Guide B-12 OL-8247-01 CISCO CONFIDENTIAL - Draft 1 A P P E N D I X Channels and Power Levels This appendix lists the IEEE 802.11b/g (2.4-GHz) and the IEEE 802.11a (5-GHz) channels and maximum power levels supported by the world’s regulatory domains. The following topic is covered in this appendix: • Channels and Maximum Power Levels, page D-2 • External Antenna Settings, page D-5 Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 D-1 Appendix D Channels and Power Levels Channels and Maximum Power Levels CISCO CONFIDENTIAL - Draft 1 Channels and Maximum Power Levels IEEE 802.11b/g (2.4-GHz Band) on Single Radio Models An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. Table 1 indicates the channel identifiers, channel center frequencies, and maximum power levels for each channel allowed by the regulatory domains: Table 1 Channels and Maximum Conducted Power for the 802.11b/g Radio with up to 10 dBi Antennas Maximum Conducted Power Levels (dBm) in the Regulatory Domains Channel ID Center Frequency (MHz) 2412 2417 2422 Americas (–A) CCK 20 20 20 OFDM 17 17 17 EMEA (–E) CCK 17 17 17 Japan (–P) OFDM CCK OFDM 17 14 14 17 14 14 17 14 14 17 14 14 2427 20 17 17 2432 20 17 171 171 14 14 17 17 17 14 14 17 17 14 14 17 17 14 14 17 17 14 14 17 17 14 14 17 17 14 14 17 14 14 10 11 2437 2442 2447 2452 2457 2462 20 20 20 20 20 20 17 17 17 17 17 12 2467 – – 17 13 2472 – – 171 171 14 14 14 2484 – – – – 14 – 1. Indicates the power level settings shipped from the factory. You might need to reset the maximum power levels used with your external antenna (see Table D-4). Cisco Aironet 1250AG Series Access Point Hardware Installation Guide D-2 OL-8247-01 Appendix D Channels and Power Levels Channels and Maximum Power Levels CISCO CONFIDENTIAL - Draft 1 IEEE 802.11b/g (2.4-GHz Band) on Dual Radio Models An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. Table D-2 indicates the channel identifiers, channel center frequencies, and maximum power levels for each channel allowed by the regulatory domains: Table D-2 Channels and Maximum Conducted Power for the 802.11b/g Radio with up to 10 dBi Antennas Maximum Conducted Power Levels (dBm) in the Regulatory Domains Americas (-A) China (-C) EMEA (-E) Israel (-I) South Korea (-K) Non-FCC (-N) Japan (-P) Singapore (-S) Taiwan (-T) Channel ID Center Freq (MHz) CCK OFDM CCK OFDM CCK OFDM CCK OFDM CCK OFDM CCK OFDM CCK OFDM CCK OFDM CCK OFDM 2412 20 17 17 17 17 17 17 17 17 17 20 17 14 14 17 17 20 17 2417 20 17 17 17 17 17 17 17 17 17 20 17 14 14 17 17 20 17 2422 20 17 17 17 17 17 17 17 17 17 20 17 14 14 17 17 20 17 2427 20 17 17 17 17 17 17 17 17 17 20 17 14 14 17 17 20 17 2432 20 17 17 17 17 17 17 17 17 17 20 17 14 14 17 17 20 17 2437 20 17 17 17 17 17 17 17 17 17 20 17 14 14 17 17 20 17 2442 20 17 17 17 17 17 17 17 17 17 20 17 14 14 17 17 20 17 2447 20 17 17 17 17 17 17 17 17 17 20 17 14 14 17 17 20 17 2452 20 17 17 17 17 17 17 17 17 17 20 17 14 14 17 17 20 17 10 2457 20 17 17 17 17 17 17 17 17 17 20 17 14 14 17 17 20 17 11 2462 20 17 17 17 17 17 17 17 17 17 20 17 14 14 17 17 20 17 12 2467 – – 17 17 17 17 17 17 17 17 – – 14 14 17 17 – – 13 2472 – – 17 17 17 17 17 17 17 17 – – 14 14 17 17 – – 14 2484 – – – – – – – – – – – – 14 – – – – – IEEE 802.11a (5-GHz Band) An improper combination of power level and antenna gain can result in equivalent isotropic radiated power (EIRP) above the amount allowed per regulatory domain. Table D-3 indicates the channel identifiers, channel center frequencies, and maximum power levels for each IEEE 802.11a 20-MHz-wide channel allowed by the regulatory domains: Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 D-3 Appendix D Channels and Power Levels Channels and Maximum Power Levels CISCO CONFIDENTIAL - Draft 1 Table D-3 Channels and Maximum Conducted Power for IEEE 802.11a Radio with up to 9.5 dBi Antennas Maximum Conducted Power Levels (dBm) in the Regulatory Domains Channel ID Center Frequency (MHz) Americas (–A) China (–C) EMEA (–E)1 Israel (–I) South Korea (–K) North America (–N) Japan (–P) Singapore (–S) Taiwan (–T) – – – – – UNII-1 (5150-5250 MHz) 34 5170 – – – – 36 5180 11 – 17 17 15 11 11 14 – 38 5190 – – – – – – – – – 40 5200 11 – 17 171 15 11 11 14 – 42 5210 – – – – – – – – – 44 5220 11 – 17 171 15 11 11 14 – 46 5230 – – – – – – – – – 15 11 11 14 – 17 82 112 – 11 48 5240 11 – 17 17 5250 to 5350 MHz 5260 172 – 172 172 172 5280 17 – 17 56 60 17 5300 172 – 172 172 172 17 82 112 11 64 5320 11 – 17 11 11 11 100 5500 172 – 172 – 172 – – – 172 104 5520 172 – 172 – 172 – – – 172 108 5540 172 – 172 – 172 – – – 172 112 5560 17 – 17 – 17 – – – 172 116 5580 172 – 172 – 172 – – – 172 120 5600 – – 172 – 172 – – – 172 – 17 – 17 – – – 172 52 17 17 17 17 11 5470 to 5725 MHz 124 5620 – 128 5640 – – 172 – – – – – 172 – 17 – – – – – 172 132 5660 17 136 5680 172 – 172 – – – – – 172 140 5700 172 – 172 – – – – – 172 5725 to 5850 MHz 149 5745 17 17 – – 17 17 – 17 17 153 5765 17 17 – – 17 17 – 17 17 157 5785 14 17 – – 17 14 – 17 14 161 5805 11 17 – – 17 11 – 17 11 165 5825 11 17 – – – 11 – 17 – 1. Indicates the power level settings shipped from the factory. You might need to reset the maximum power levels used with your external antennas (see Table D-5). 2. Indicated frequencies require DFS (Uniform spreading not required for the -P domain) Cisco Aironet 1250AG Series Access Point Hardware Installation Guide D-4 OL-8247-01 Appendix D Channels and Power Levels External Antenna Settings CISCO CONFIDENTIAL - Draft 1 External Antenna Settings Maximum Power Levels in Some Regulatory Domains with External Antennas Caution Table D-4 To avoid exceeding maximum conducted power levels in the China (–C), EMEA (-E), South Korea (–K), Israel (–I), and Singapore (–S) regulatory domains when using an 802.11b/g radio with 2.2- to 10-dBi external antennas, you must manually set the access point output power level as shown in Table D-4. Maximum Power Levels for the 802.11b/g Radio in the (–C), (–E), (–K), (–I), and (–S) Regulatory Domains Maximum Power Levels (dBm) Channel ID Center Frequency (MHz) 2.2 dBi Antenna 5.2 dBi Antenna 6.0 dBi Antenna 6.5dBi Antenna 9.0 dBi Antenna 10 dBi Antenna 2412 17 14 14 11 11 2417 17 14 14 11 11 2422 17 14 14 11 11 2427 17 14 14 11 11 2432 17 14 14 11 11 2437 17 14 14 11 11 2442 17 14 14 11 11 2447 17 14 14 11 11 2452 17 14 14 11 11 10 2457 17 14 14 11 11 11 2462 17 14 14 11 11 12 2467 17 14 14 11 11 13 2472 17 14 14 11 11 14 2484 – – – – – – Cisco Aironet 1250AG Series Access Point Hardware Installation Guide OL-8247-01 D-5 Appendix D Channels and Power Levels External Antenna Settings CISCO CONFIDENTIAL - Draft 1 Caution Table D-5 Channel ID To avoid exceeding maximum conducted power levels in the EMEA (-E) and Israel (–) regulatory domains when using a IEEE 802.11a radio with 6.0- to 9.5-dBi external 5-MHz antennas, you must manually set the access point output power level as shown in Table D-5. Maximum Power Levels for IEEE 802.11a Radio in the EMEA(–E) and Israel (–I) Regulatory Domains Center Frequency (MHz) Maximum Power Levels (dBm) 3.5 dBi Antenna 34 36 38 40 42 44 46 48 5170 5180 5190 5200 5210 5220 5230 5240 – 17 – 17 – 17 – 17 52 56 60 64 5260 5280 5300 5320 17 17 17 17 100 104 108 112 116 120 124 128 132 136 140 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 17 17 17 17 17 17 17 17 17 17 17 149 153 157 161 165 5745 5765 5785 5805 5825 – – – – – 4.5 dBi Antenna 6.0 dBi Antenna UNII-1 (5150-5250 MHz) – – 17 15 – – 17 15 – – 17 15 – – 17 15 5250 to 5350 MHz 17 15 17 15 17 15 17 15 5470 to 5725 MHz 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 5725 to 5850 MHz – – – – – – – – – – 7.0 dBi Antenna 9.5 dBi Antenna – 15 – 15 – 15 – 15 – 11 – 11 – 11 – 11 15 15 15 15 11 11 11 11 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 – – – – – – – – – – Cisco Aironet 1250AG Series Access Point Hardware Installation Guide D-6 OL-8247-01
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 32 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:e508f2ab-726f-40e0-9a7e-a6b3d2128158 Producer : Acrobat Distiller 6.0.1 (Windows) Creator Tool : PScript5.dll Version 5.2 Modify Date : 2006:02:23 16:51:42-05:00 Create Date : 2006:02:23 13:36:52-05:00 Metadata Date : 2006:02:23 16:51:42-05:00 Document ID : uuid:097fad0e-4350-47a1-bc98-1dc4244555fc Format : application/pdf Title : 125h_tl.fm Creator : jdugas Author : jdugasEXIF Metadata provided by EXIF.tools