Cisco Systems 102065 802.11 b/g Access Point User Manual a521qsgb

Cisco Systems Inc 802.11 b/g Access Point a521qsgb

UserManual.wiki >

Cisco Systems >

102065 User Manual

User Manual

DRAFT—CISCO CONFIDENTIALRead This First 1Radio and IP Address Configuration 1How to Open the Top Cover 2Safety Information 5Warnings 5Overview 7Unpacking the Access Point 7Installation Summary 10Mounting the Access Point 11Connecting Power 12Obtaining an IP Address 12Configuring Power 13Configuring Basic Settings 13Configuring Security Settings 14Understanding Express Security Settings 14a521qsg.fmb Page 1 Monday, March 12, 2007 10:40 AM

DRAFT—CISCO CONFIDENTIALExpress Security Limitations 14SSID Configuration 14In Case of Difficulty 15Checking the Access Point LEDs 16Checking Basic Settings 17Resetting to Default Configuration 18Using the MODE Button 18Using the Web Browser Interface 19Compliance Information 19Cisco 90-Day Limited Hardware Warranty Terms 20a521qsg.fmb Page 2 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL1Quick Start Guide Cisco Aironet 521 Access PointsRead This FirstYou should review this table and the instructions for opening the top cover. The table contains important information you need to know so you can successfully configure your access point.Radio and IP Address ConfigurationThe access point ships with its radio disabled.You must enable them when you configure the access point for the first time. Also, the access point no longer is assigned an IP address. It is configured to obtain an IP address using Setting DefaultLoginPasswordIP addressService Set Identifier (SSID)Status LED Status Descriptiona521qsg.fmb Page 1 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL278-18092-01a DHCP server. If your network does not use a DHCP server, you must connect to the access point’s console port and assign a static IP address (See the “Assigning an IP Address Using the CLI” section on page 17.How to Open the Top CoverThe top cover provides access to the cable and power connections.Caution Do not open the access point top cover as you would a hatch or door. You could damage the cover by doing so. An instruction label is attached to the access point. Take time to read the label before you open the access point cover.When you have familiarized yourself with the opening procedure, we recommend that you remove the label, putting it in a safe place, such as inside the cover of this guide.Note Status LED indications are not visible when the top cover is open.Follow these steps to open the top cover:1. Put the access point on a flat surface, and grasp it with both hands, as shown in this illustration.a521qsg.fmb Page 2 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL3Quick Start Guide Cisco Aironet 521 Access Points121061Cable access notchand arrowa521qsg.fmb Page 3 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL478-18092-012. Gently push the cover away from you until it stops, as shown in this illustration.3. Remove the opening instruction label from the top cover. Note We recommend that you save the label for reference. 121423a521qsg.fmb Page 4 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL5Quick Start Guide Cisco Aironet 521 Access PointsSafety Information The FCC, with its action in ET Docket 96-8, has adopted a safety standard for human exposure to RF electromagnetic energy emitted by FCC-certified equipment. When used with approved Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper operation of this radio device according to the instructions in this document and the installation and configuration guide will result in user exposure substantially below the FCC recommended limits.•Do not hold any component containing a radio such that the antenna is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.•The use of wireless devices in hazardous locations is limited to the constraints posed by the safety directors of such environments.WarningsWarningThis product must be connected to a Power-over-Ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source.a521qsg.fmb Page 5 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL678-18092-01WarningIn order to comply with FCC radio frequency (RF) exposure limits, antennas should be located a minimum of 7.9 in. (20 cm) or more from the body of all persons.WarningDo not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use.WarningDo not work on the system or connect or disconnect cables during periods of lightning activity.WarningRead the installation instructions before you connect the system to its power source.a521qsg.fmb Page 6 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL7Quick Start Guide Cisco Aironet 521 Access PointsWarningThis product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A.OverviewThis guide is designed to help you minimally configure a Cisco Aironet 521 Series Access Point using the access point graphical user interface (GUI) through your web browser. The GUI is the primary-configuration tool. This guide provides an overview of the access point and provides instructions for mounting it. Do not attempt to connect a cable with a protective boot to the access point Ethernet or console port. Because of limited space in the connection area, booted connectors will not fit.Unpacking the Access PointEach access point package contains the following items:•TBD•Mounting hardware kit - TBDa521qsg.fmb Page 7 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL878-18092-01•This guideComplete these steps to prepare for installation.1. Carefully unpack and remove the access point and hardware kit from the shipping box.2. Return all packing material to the shipping container, and save it.3. Verify all the package contents, and inspect each item for damage. If any item is missing or damaged, contact your Cisco representative for support.4. Become familiar with the access point and its features, which are identified in this illustration.Caution Be careful when handling the access point; the bottom plate might be hot.a521qsg.fmb Page 8 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL9Quick Start Guide Cisco Aironet 521 Access Points1Power connector 5Padlock post2Ethernet port 6Mode button3Keyhole slot 7Ethernet (E) and Radio (R) LEDs4Console port 8Status LED12154168451237a521qsg.fmb Page 9 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL1078-18092-01Installation SummaryInstalling the access point involves these operations:•Mounting the access point •Connecting power•Configuring basic settings•Configuring security settingsBefore you install the access point, make sure that you are using a computer connected to the same network as the access point, and obtain the following information from your network system administrator:•TBDa521qsg.fmb Page 10 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL11Quick Start Guide Cisco Aironet 521 Access PointsIf you are not connected to a DHCP server, you can assign an IP address to the access point using the CLI. In this situation, obtain a unique IP address for your access point, a default gateway, and subnet mask from your network system administrator.Mounting the Access PointThe access point uses a detachable universal mounting plate to mount the access point to flat surfaces such as a wall or ceiling. The universal mounting plate is also used to mount the access point to an electrical or network junction box, or to the provided rail clips for below a suspended ceiling.The mounting process is simple and requires common tools. Because it is detachable, you can use the universal mounting plate to mark the positions of the mounting holes for your installation. You then install the universal mounting bracket on the surface and attach the access point when you are ready.When you have mounted the access point, its padlock post enables you to protect the Ethernet, power cables, and Mode button, and to lock the access point with a padlock.a521qsg.fmb Page 11 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL1278-18092-01Connecting PowerConnect the 521 series access point to a power source. The access point can be powered locally by using an AC power module or over the Ethernet using power sourcing equipment (PSE). When power is supplied to the access point, a routine power-up sequence begins which you can monitor by observing the access point status LED. During the power up sequence the LED displays a series of colors. When the power up sequence is complete, the LED displays a light green color to indicate that it is ready for operation. When a client associates to the access point, the status LED changes to blue. The LED displays amber to indicate a problem, such as when the access point is unable to verify that the PSE is supplying sufficient power. See the “Configuring Power” section on page 17.Obtaining an IP AddressYour access point needs an IP address to operate. The access point is no longer shipped with a default IP address. It obtains an IP address from your network’s DHCP server when you connect the access point to your network. If your network does not have a DHCP server, the access point continues to request an IP address until you assign it one. a521qsg.fmb Page 12 Monday, March 12, 2007 10:40 AM

DRAFT - CISCO CONFIDENTIAL13Quick Start Guide Cisco Aironet 521 Access PointsYou must know your access point’s IP address before you can use the web-based management GUI. If your access point obtained its IP address from your network’s DHCP server, you or your network administrator can find it by querying the DHCP server using the access point’s MAC address. You can also find the access point’s IP address using Cisco’s IP Setup Utility You can download IPSU from Cisco.com.Configuring PowerAfter connecting the access point to a power source, its status LED might be amber, which can indicate that the access point is unable to verify that the PSE is supplying sufficient power. In such cases, you will need to configure settings on the access point or the switch to identify your power source.Configuring Basic SettingsFollow these steps to configure basic settings for the access point using the GUI Express Setup page.a521qsg.fmb Page 13 Monday, March 12, 2007 10:40 AM

$DRAFT - CISCO CONFIDENTIAL1478-18092-01Configuring Security SettingsAfter you assign basic settings to your access point, you must configure security settings to prevent unauthorized access to your network. Because it is a radio device, the access point can communicate beyond the physical boundaries of your work site. Understanding Express Security SettingsTBDExpress Security LimitationsTBDSSID ConfigurationTBDNote These characters are not allowed: ?, “, $, [, \, ], and +. In addition, these characters cannot be the first character: !, #, and ;.a521qsg.fmb Page 14 Monday, March 12, 2007 10:40 AM$

Cisco Systems 102065 802.11 b/g Access Point User Manual a521qsgb

Cisco Systems Inc 802.11 b/g Access Point a521qsgb

User Manual

Navigation menu

Namespaces

Views

Navigation