Cisco Systems 2305-BTS2-R1 Base Station Transmitter User Manual Ripwave Base Station I C Guide
Cisco Systems, Inc Base Station Transmitter Ripwave Base Station I C Guide
Contents
Manual part 3
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 588300 |
| Application ID | PpHHLWIKMHTknLd9hQ0M6A== |
| Document Description | Manual part 3 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 15.93kB (199134 bits) |
| Date Submitted | 2005-10-04 00:00:00 |
| Date Available | 2005-10-04 00:00:00 |
| Creation Date | 2005-02-04 14:58:10 |
| Producing Software | Acrobat Distiller 6.0 (Windows) |
| Document Lastmod | 2005-02-04 14:58:26 |
| Document Title | Ripwave Base Station I&C Guide |
| Document Creator | Acrobat PDFMaker 6.0 for Word |
| Document Author: | L. Font |
Navini Networks, Inc. Ripwave Base Station I&C Guide Chapter 1: Overview Ripwave Description A Ripwave system has three main components: the Base Station, the Modems, and the Element Management System (EMS). The Base Station performs the Modem registration and call processing, and provides the interface between the backhaul network and the EMS. It is made up of the Base Transceiver Station (BTS) and the Radio Frequency Subsystem (RFS) (Figures 1, 2 & 3). This manual provides the guidelines and instructions for installing and commissioning (I&C) the Base Station. Figure 1 shows the system with both Secondary (built-in) and Primary (optional) Lightning Protection. Lightning Protection helps to protect the RFS, the BTS, and the RF lines against “tower lightning” events occurring at the Base Station. The customer must exercise judgment when balancing risk against cost to decide whether to install the primary protection kit at an extra cost or to rely on the secondary protection only. NOTE: Navini does not warranty equipment against lightning strikes. In addition to tower lightning events occurring at the base station, lightning events that occur miles away from the BTS could generate intense electrical currents traveling over the power and/or backhaul lines and into the BTS equipment, damaging it. For this reason, Navini recommends adding surge protection devices at the power and backhaul demarcation points. Figure 1: TTA Configuration with Primary and Secondary Surge Protection Omni or Panel Antenna Lightning Ground Power Amplifiers Secondary (Built-in) Surge Protectors Antenna Bracket Primary Surge Protectors (Use Polyphasor surge protectors with the CAL Cable and Huber+Suhner surge protectors everywhere else) Additional grounding block needed if main cable run exceeds 250 ft (75 m) Secondary (Built-in) Surge Protectors GPS Antenna Use "Smart Jack" for surge protection!!! These are not Surge Protectors but N-type/Female to N-type/Female bulhhead connectors for grounding Ethernet RF GPS Demarc. Points CAL 110/220 VAC 60/50 Hz Digital Shelf Rectifiers (24 VDC, 60 A) Rectifier Frame Surge Protection Device 5 Ohm maximum 21 Navini Networks, Inc. Ripwave Base Station I&C Guide Figure 2: TTA Configuration with Secondary Surge Protection Only Lightning Omni or Panel Antenna Power Amplifiers Ground Secondary (Built-in) Surge Protectors Antenna Bracket Secondary (Built-in) Surge Protectors GPS Antenna 14 dB max MAY BE NEEDED DEPENDING ON THE COUNTRY OR CITY BUILDING CODES These are not Surge Protectors but Ntype/Female to N-type/Female bulhhead connectors for grounding Use "Smart Jack" for surge protection!!! RF GPS Ethernet Demarc. Points CAL 110/220 VAC 60/50 Hz Digital Shelf Rectifiers (24 VDC, 60 A) Rectifier Frame Surge Protection Device 5 Ohm maximum CAUTION! Although Secondary surge protection is built into the TTA that ships from the factory, Navini recommends that the Primary surge protection kit be purchased and installed, in particular if the equipment is installed in an area where electrical storms are common. Surge protection devices should be added in front of the rectifier. Lightning striking miles away from the BTS may cause an intense electric current traveling on the power and/or backhaul lines and into the BTS, damaging the equipment. 22 Navini Networks, Inc. Ripwave Base Station I&C Guide Procedural Documents & Forms You will refer to other Ripwave documents, procedures, and forms in the process of installing and commissioning the Base Station. The product documentation is provided on the Ripwave Standard Documentation CD (Table 1). As well, the EMS manuals can be viewed on-line through the EMS Server and Client applications. Table 1: Ripwave Standard Documentation CD Order Number 95-00116-00 EMS Overview Manual EMS Software Installation Guide EMS-OSS Integration Guide EMS Administration Guide Ripwave Configuration Guide Excel Configuration Form EMS CLI Reference Manual Ripwave Alarm Resolution Reference Manual System Operations, Maintenance & Troubleshooting Guide* EMS Diagnostic Tools Guide Ripwave Modem Quick Installation Guide English Spanish Ripwave Modem User Guide English Spanish Ripwave Modem Software Update Tool Quick Guide Customer Release Notes *Available 2Q04 Part Number 40-00016-03 40-00017-00 40-00147-00 40-00031-00 40-00016-01 44-00032-01 40-00016-02 40-00033-00 00-00046-00 40-00032-00 40-00112-00 40-00098-00 40-00096-00 40-00111-00 40-00097-00 40-00099-00 40-00066-00 Varies w/each release A number of other forms are used in the installation and commissioning process. This I&C Guide references those throughout, and provides copies in the appendices. High-level I&C Process To put the I&C activities in the context of overall system deployment, Figure 4 provides a ‘flow’ of the key activities that are performed prior to and during the installation and commissioning of the Ripwave Base Station. Post-I&C, the system that has been installed and commissioned goes through Acceptance Testing against the customer’s objectives for that site. Once customer signoff on the site is achieved, the customer becomes fully responsible for operating the system. You may find this flowchart can be used as a helpful checklist during the process. 23 Navini Networks, Inc. Ripwave Base Station I&C Guide Different job holders may perform various portions of these activities and not necessarily all of the activities. In fact, Marketing and Engineering personnel typically handle the earlier tasks, while installation may be a stand-alone function. Commissioning may or may not be handled by the same people who designed or installed the site. Regardless of who does them, these key activities have to be accomplished for successful deployment: • • • Site Selection, Design, and Preparation Physical Installation Commissioning, with Acceptance Testing and Sign-off Prior to installation, Navini and the customer formulate a Project Plan and Responsibility Assignment Matrix (RAM) to clarify who will do what to complete the I&C activities. If requested by the customer, Navini may provide personnel, procedures, forms, and/or tools required to install and commission the Base Station equipment. They may also provide special commissioning software programs, computers, and any other special test equipment required. As part of the I&C duties, all testing results are recorded and kept for the customer to review and approve. These test results include the cable sweeps, the BTS Calibration Verification, RF System Tests, Drive Study, Line-of-Sight (LOS) FTP tests, and Non-Line-of-Sight (NLOS) FTP test results. The I&C Supervisor provides site tracking and weekly status reports. All of these tasks can be negotiated with the customer. If Navini Networks is hired by a customer to provide Installation & Commissioning Services, involvement and some actual deliverables are still required by the customer. For example, the customer will need to review or perhaps even explain their Site Design Specifications, approve Logistics Plans, provide shipping information, approve the Network Architecture Plan, etc. As part of a successful hand-off from Navini to the customer, it is usually necessary for Navini to provide some product training to customer personnel who will support the Base Station operation on-going. Customers may opt to take on a Train-the-Trainer program, in which case Navini certifies the customer’s instructors who then provide staff training thereafter. 24 Navini Networks, Inc. Ripwave Base Station I&C Guide Figure 4: High Level I&C Process Flowchart Phase I: Pre-installation - Site Selection, Design & Preparation BEGIN 1 - Complete the Project Plan for this deployment.2 - Generate a coverage prediction map. 3 - Conduct a site survey, filling out the Site Candidate Evaluation Form. 4 – If this is a 2.4 GHz system, complete the Interference Analysis, following the Interference Sweep Procedure. Appendix A: Site Candidate Evaluation Form Appendix B: Interference Sweep Procedure Appendix C: BTS Specifications Appendix D: RFS Data Sheets 5 - Acquire information about the final site selected by the customer. Physical site design completed. Appendix E: BTS Outdoor Enclosure Mfrs. Appendix F: Rectifier/BBU Manufacturers Appendix G: Sample Base Station Drawing 25 Navini Networks, Inc. Ripwave Base Station I&C Guide Phase I: Pre-installation - Site Selection, Design & Preparation, continued 6 - Complete the Network Architecture design. 7 - Antenna Power & Cable selection procedure. Appendix H: Antenna Power & Cable Selection Procedure & Form 8 - Develop a Bill of Materials (BoM). Appendix I: Sample BoM 9 - Acquire the materials. 10 - Confirm the customer backhaul, EMS Server, FTP Server, input power and grounding are installed and operational at site. 26 Navini Networks, Inc. Ripwave Base Station I&C Guide Phase II: Installation 1 - From the shipping containers received at the customer site, gather Manufacturing’s inventory sheet and test data that was collected before the BTS & RFS equipment shipped. Verify all equipment arrived (inventory it), serial numbers match paperwork, and the test data is available. Keep this as part of the customer site records. 2 - Install all system buss bars and surge protectors. 3 - Cut cables. Install connectors on cables. Appendix J: Install Connectors 4 - Install & sweep the RF cables. Record results on the RFS System Test Form. Appendix K: RFS System Test (cables & RFS sweep) 5 - Install & sweep the GPS cables. 6 - Test & install the data/power cable (Non-TTA BTS). 7 - If required, install the BTS mounting rack. Appendix L: Chassis Alarms Information 8 - Install the BTS chassis. 9 - Install & verify the BTS & RFS grounding. 27 Appendix M: Sample Tri-sector BTS Grounding Drawing Navini Networks, Inc. Ripwave Base Station I&C Guide Phase II: Installation, continued 10 - Install & verify the DC input power source to the BTS. Appendix N: Sample Tri-sector BTS Power Drawing 11 - Install the GPS antennas. 12 - Sweep the RFS. Record the results & the RFS serial numbers on the RFS System Test Form (same form as Step 3, Appendix K). 13 - Install the RFS & surge protectors and Connect cables to the RFS. 14 - Sweep the installed RFS & cables to verify connections & cable loss. Record results on the RFS System Test Form (same form as Steps 3 & 11, Appendix K). 15 - Verify that all cards are installed and seated properly. 16 - Record the serial & version numbers of the digital and RF/PA cards on the Base Station Installation Certification Form. 28 Appendix O: Base Station Installation Certification Form Navini Networks, Inc. Ripwave Base Station I&C Guide Phase II: Installation, continued 17 - If required in the Responsibility Assignment Matrix (RAM) portion of the Project Plan, test the backhaul to the customer demarcation point. 18 - Provide a printed package of the measured results and equipment inventory to the customer on-site. 19 - Go over the results using the printed package and obtain customer sign-off on the completion of the Installation portion of the work. Use the Base Station Installation Certification Form for sign-off (same form as Step 16, Appendix P). 29 Navini Networks, Inc. Ripwave Base Station I&C Guide Phase III: Commissioning 1 - Review the customer’s network plans - i.e., ATM vs Ethernet backhaul. No 2 - Are you using the customer’s EMS Server? 3a - Install & configure the Test EMS Server & Client. Yes 3b - Install & configure the customer EMS Server & Client. 4 - Install & configure the BTS in the EMS 5 - Enter the RFS configuration by running the RFS script that shipped with the antenna equipment. 6 - Verify that all cables are connected. 7 - Power up the BTS & reconfigure the basic Boot Line parameters through the serial port on the CC card. 8 - After the BTS has been powered up at least 20 minutes. 30 Appendix P: Excel Configuration Form Navini Networks, Inc. Ripwave Base Station I&C Guide Phase III: Commissioning, continued 9 – Perform 3 calibrations. No 10 - Did it pass calibration? 11a - Perform system troubleshooting procedures. Yes Appendix Q: Base Station Calibration Verification Form 11b - Perform Base Station Calibration Verification. Record the measurements on the Base Station Calibration Verification Form (I&C Closeout Tool) No 12 - Did it pass calibration verification? Yes 13 - Perform the Single Antenna Element Test procedure. 31 Appendix R: Single Antenna Element Test Procedure Navini Networks, Inc. Ripwave Base Station I&C Guide Phase III: Commissioning, continued No 14 -Was the Test EMS used? Yes 15 - Install & configure the Customer EMS Server & Client. 16 – Configure BTS in the Customer EMS 17 - Enter the RFS configuration by running the RFS script that shipped with the antenna equipment. 18 – Verify EMS & BTS connectivity. Verify that the latency between EMS and BTS is less than 10 milliseconds 19 - Perform calibration. Ensure successful results 3 times. 32 Navini Networks, Inc. Ripwave Base Station I&C Guide Phase III: Commissioning, continued 20 - Verify that the GPS & Constellation Debugger are installed and operational on the Drive Study laptop 21 - Perform the LOS Location (FTP) Test. Complete 3 uploads & 3 downloads at 3 locations. Record the results on the FTP Test Form. (I&C Closeout Form) Appendix S: Location (FTP) Test Procedure & Form 22 - Perform the NLOS Location (FTP) Test. Complete 3 uploads & 3 downloads at 3 locations. Record the results on the FTP Test Form. (I&C Closeout Form) Appendix S: Location (FTP) Test Procedure & Form Appendix T: Drive Study Form 23 - Perform full Drive test Study. Record the results on the Drive Study Form. (I&C Closeout Form) 24 - Send test results to Navini Technical Support. No 25 -Results 24b - Perform full Drive Study, and adequate? record the results on the Drive Study Form. This is used Yes for tuning the model (same form as Step 19, Appendix X). 33 26a - Adjust the RF parameters and troubleshoot. Recalibrate BTS Navini Networks, Inc. Ripwave Base Station I&C Guide Phase III: Commissioning, continued 26b- Verify system operation with multiple Modems in use. 27 - Back up the EMS database. 28 - Gather all required documents & forms to create a delivery package for the Customer signoff and for the Navini Techical Support database. See Installation Closeout Documentation. 29 - Participate in the Customer sign-off of the Customer Acceptance Form. 34 Appendix U: Site Installation Closeout Documentation Appendix V: I&C Closeout form Appendix W: Customer Acceptance Form
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 14 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:d66fff83-d0a1-4cda-b833-5f7f65a642da Producer : Acrobat Distiller 6.0 (Windows) Comments : Standard Release 4.1.6 Category : documentation Company : Navini Networks, Inc. Manager : S. Redfoot Create Date : 2005:02:04 14:58:10-06:00 Creator Tool : Acrobat PDFMaker 6.0 for Word Modify Date : 2005:02:04 14:58:26-06:00 Metadata Date : 2005:02:04 14:58:26-06:00 Document ID : uuid:4b64630a-be37-4fb0-a10a-8cf8e493d755 Format : application/pdf Title : Ripwave Base Station I&C Guide Creator : L. Font Description : Base Station Author : L. Font Subject : Base Station Keywords : BTS, install, commission, I&CEXIF Metadata provided by EXIF.tools