Cisco Systems 2500-PCM19-R1 PCMCIA Broadband Wireless Access card User Manual Ripwave Modem User Guide

Cisco Systems, Inc PCMCIA Broadband Wireless Access card Ripwave Modem User Guide

User guide

RRiippwwaavvee WWiirreelleessss BBrrooaaddbbaanndd AAcccceessss ((PPCC)) CCaarrdd UUsseerr’’ss GGuuiiddee Part Number 40-00292-00 Revision A, Version 1.0, PV1.2 May 25, 2005 Proprietary All information disclosed by this document is the proprietary property of Navini Networks, Inc. and is protected by copyright, trademark, and/or trade secret laws. All rights therein are expressly reserved.
Navini Networks, Inc. Ripwave Wireless Broadband Access (PC) Card User’s Guide Page 2 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) TABLE OF CONTENTS PERMISSIONS, TRADEMARKS & DISTRIBUTION................................................................................................................... 3 SAFETY ........................................................................................................................................................................................ 4 REGULATORY INFORMATION.................................................................................................................................................. 5 INTRODUCTION.......................................................................................................................................6 PACKAGE INVENTORY.........................................................................................................................6 RIPWAVE MODELS.................................................................................................................................6 MINIMUM COMPUTING REQUIREMENTS......................................................................................7 PHYSICAL CHARACTERISTICS..........................................................................................................7 INSTALLING THE PC CARD ON WINDOWS 2000 ...........................................................................8 ACCESSING THE INTERNET..............................................................................................................11 DISCONNECTING THE PC CARD......................................................................................................11 INDICATOR LIGHT...............................................................................................................................13 TROUBLESHOOTING...........................................................................................................................13 INSTALLING NAVINI DIAGNOSTICS (NAVDIAG) SOFTWARE................................................13 USING NAVINI DIAGNOSTICS ...........................................................................................................18 UNINSTALLING NAVINI DIAGNOSTICS SOFTWARE.................................................................23 UPGRADING THE PC CARD................................................................................................................26 ADDENDUM 1: PC CARD - PC TROUBLESHOOTING...................................................................27 ADDENDUM 2: END USER SOFTWARE LICENSE AGREEMENT.............................................31
Navini Networks, Inc. Ripwave Wireless Broadband Access (PC) Card User’s Guide Page 3 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Permissions, Trademarks & Distribution Copyright© 2004 - 2005, Navini Networks, Inc. All information contained herein and disclosed by this document is confidential and the proprietary property of Navini Networks, Inc. and all rights therein are expressly reserved. Acceptance of this material signifies agreement by the recipient that the information contained in this document is confidential and that it will be used solely for the purposes set forth herein. Acceptance of this material signifies agreement by the recipient that it will not be used, reproduced in whole or in part, disclosed, distributed, or conveyed to others in any manner or by any means – graphic, electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval systems – without the express written permission of Navini Networks, Inc. Navini Networks is a registered trademark. The Navini Networks logo, Zero-Install, Ripwave, and Unwired by Navini are trademarks of Navini Networks, Inc. Other product and company names mentioned herein may be trademarks and/or service marks of their respective owners. Except for the hardware warranty, nothing herein constitutes any representation, warranty, assurance, or guaranty of any kind. Because of continuing developments and improvements in design, manufacturing, and deployment, material in this document is subject to change without notification and does not represent any commitment or obligation on the part of Navini Networks, Inc. Navini Networks, Inc. shall have no liability for any error or damages resulting from the use of this document. All Navini Networks logos and trademarks are the property of Navini Networks, Inc. Unauthorized usage is strictly prohibited without the express written permission of Navini Networks, Inc. © 2004 - 2005 Navini Networks, Inc. All rights reserved.
Navini Networks, Inc. Ripwave Wireless Broadband Access (PC) Card User’s Guide Page 4 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Safety When using a Ripwave Wireless Broadband Access Card, always follow basic safety precautions to reduce the risk of electrical shock, fire, and injury to people and/or property. Follow all warnings and instructions that come with the equipment. 1. Do not use the equipment while you are in a bathtub, shower, pool, or spa. Exposure of the equipment to water could cause severe electrical shock or serious damage to the equipment. 2. Do not immerse the equipment in any type of liquid. Use a damp, lint-free cloth and if needed, an electrical contact cleaner that is non-conductible to clean the Modem card. Unplug the Modem card from the PC before cleaning. Do not use chemicals or abrasive to clean the Modem card. Also, use caution around the connection pins. 3. Follow all airport and FAA regulations when using the equipment on or near aircraft. 4. Do not use the Ripwave Wireless Broadband Access Card near medical equipment, life support equipment, or any equipment that may be susceptible to any form of radio interference. In such areas, the Card must be powered off. 5. The driver or operator of any vehicle should not operate the Ripwave Wireless Broadband Access Card while in control of a vehicle. Doing so will detract from the driver or operator’s control and operation of the vehicle. 6. Do not disassemble the equipment. Removing covers may expose dangerous voltages or other risks and also voids the warranty. Incorrect reassembly can cause equipment damage or electrical shock. Only an authorized repair technician should service this product. 7. Do not expose the equipment to extreme hot or cold temperatures. 8. Do not use the equipment under the following conditions: • When the equipment has been exposed to water or moisture. • When the equipment has been damaged. • When the equipment does not operate properly or shows a distinct change in performance.
Navini Networks, Inc. Ripwave Wireless Broadband Access (PC) Card User’s Guide Page 5 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Regulatory Information This Ripwave Wireless Broadband Access Card has been tested with a typical laptop computer with a side loading PCMCIA bay. This PC Card must not be co-located or operated in conjunction with any antenna (other than the one furnished by Navini and included in the package) or transmitter. Use of this device in any other configuration may exceed the FCC, ETSI, or other regulatory bodies RF Exposure compliance limit. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna, 2) Increase the separation between the equipment and the receiver, 3) Consult the dealer or an experienced radio technician for additional suggestions. FCC guidelines stipulate that the antenna should be more than 2.5 cm (1”) from bystanders and 1.0 cm (0.39”) from the user. When in use, the antenna should be pointed vertically upward. When using the Remote Desktop Antenna with the PC Card, a minimum distance of 20 centimeters (8 inches) is required from the user or bystander. SAR, or Specific Absorption Rate, is the measurement for the rate at which electromagnetic energy is absorbed by the human body during exposure. The FCC states the body SAR limit be: 1.6 W/kg. The highest reported SAR value for the PC card is 1.01 W/kg.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 6 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Introduction Package Inventory Ripwave Models Congratulations! The Ripwave Wireless Broadband Access Card, or PC Card for short, is a user-friendly, easy-to-install device that helps you connect wirelessly to the Internet using the Network Interface Card (NIC) port on a laptop computer. It provides complete broadband Internet access to residential and small office/home office (SOHO) users without the necessity of professional hardware installation. The PC Card allows you to have portable Internet or other wireless access service. A computer with this device can be moved from room to room, location to location, or even city to city as long as there is coverage and appropriate reception in the area. Please verify the contents of your PC Card package. If you do not find all of these items in your package, notify the supplier from whom you obtained the package. • The Ripwave Wireless Broadband Access Card • External antenna • Installation CD containing: - PC driver software - Navini Diagnostics application - User’s Guide • Printed copy of the Quick Installation Guide Your PC Card operates in one of the following frequency ranges: 2.5-2.6, 3.4, or 3.5 GHz. The frequency number appears on the Card’s label. Operating Frequencies: Model Frequency Range Operating Band 2.5-2.6 GHz 2.500 GHz - 2.686 GHz MMDS/ITFS 3.4 GHz 3.410 Ghz – 3.525 GHz WLL 3.5 GHz 3.475 GHz – 3.600 GHz WLL
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 7 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Minimum Computing Requirements (See, also, Addendum 1) Physical Characteristics Operating System1: Windows 98SE, Windows 2000, Windows ME, or Windows XP. It is assumed the latest Windows service pack is installed on the Operating System. Note: The PC Card is not supported on MacIntosh systems or Linux/Unix systems. CPU: Pentium level or higher RAM: 32 MB or the Operating System minimum, whichever is greater Hard Drive: 50 MB free disk space for the optional Navini Diagnostics software Monitor: 256 colors, 800 x 600 resolution NOTE1: If you are going to upgrade your Operating System after loading the Navini Diagnostics software, you must first uninstall Navini Diagnostics prior to upgrading the OS. Otherwise, the Wireless Modem Card will continue to operate, but the Navini Diagnostics will not work. See Uninstall instructions in this Guide. This manual will guide you through the simple process of installing the PC Card and driver software, which have been developed to optimize the ease and convenience for you, our valued customer. If you experience any difficulties with your card, refer to the Troubleshooting sections of this guide. If further assistance is needed, please contact your Service Provider or the vendor from whom you obtained your PC Card. The PC Card fits into a standard Type II PC network interface card (NIC) slot. A 68-pin connector resides on the end of the card that is inserted into the slot. PC Card 68-pin connector
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 8 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Physical Characteristics, continued Installing the PC Card on Windows 2000 Depending on which model you have, one or two internal inverted-F antennas reside inside the card. The 2.5-2.6 GHz model has one internal inverted F antenna while the 3.4 and 3.5 GHz models have two internal inverted F antennas. There is also an external antenna. Following is a picture of the external antenna in the upright position. To raise the antenna to its upright position, raise the antenna counterclockwise. Do not turn the antenna beyond its upright position. The following instructions explain how to install a PC Card and its driver software. Please read all instructions before attempting the installation. Note: The screenshots shown in these instructions were taken from a laptop operating with Windows 2000. If you have a Windows 98, XP, or ME operating system, the screens you see may vary from the screens shown in the instructions. Step Action Illustration 1. Insert the card into the Type II card slot on your computer. Be sure to insert the end that has the 68-pin connector into the card slot. 2. Raise the antenna to the upright position. 3. The Found New Hardware box appears indicating the PC sees the PC Card. Windows 2000 Screen
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 9 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Installing the PC Card, continued Step Action Illustration 4. The Welcome to the Found New Hardware Wizard dialog box appears. Click Next to continue. Windows 2000 Screen 5. The Install Hardware Device Drivers box appears. Select ‘Search for a suitable driver for my device (recommended).’ Click Next to continue. Windows 2000 Screen 6. The Locate Driver Files box appears. Select ‘CD ROM.’ Insert the Installation CD into the computer’s CD-ROM drive. Click Next to continue. Windows 2000 Screen
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 10 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Installing the PC Card, continued Step Action Illustration 7. The Driver Files Search Results box appears. Click Next to install the driver. Windows 2000 Screen 8. The Hardware Install box appears, along with a Digital Signature Not Found box. Click Yes on the Digital Signature Not Found box, and then click Yes on the Hardware Install box. If the sound is turned up on your computer, two beeps are heard. Note: Windows 98, XP, or ME systems may show a screen stating the PCMCIA Adapter* has not passed Windows Logo testing and asking if you want to continue installation. Select the option that continues the installation. Windows 2000 Screen *PCMCIA is a generic name for any NIC type device.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 11 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Installing the PC Card, continued Accessing the Internet Disconnecting the PC Card Step Action Illustration (using LED Modem) 9. After the files are copied, a Completing the Found New Hardware Wizard box appears indicating the driver installation is complete. Click Finish to close the Wizard. Windows 2000 Screen Assuming you have service from a Service Provider, you should be able to surf the Internet once your PC Card is installed, and the computer is powered on! To access the Internet, open the web browser that is installed on your computer, i.e., Netscape, Internet Explorer, etc. Before you pull the PC Card out of the computer card slot, you must first stop the driver software. If you do not stop the driver software first, the following box will appear: To safely disconnect the PC Card, click on the Card icon indicated in the following illustration. This icon is located in the lower right-hand corner of the computer.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 12 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Disconnecting the PC Card, continued Once you click on the icon indicated, a list with one or more elements will appear. This list is dependent on the devices currently installed on the PC. For example: Select Stop Navini Networks PCMCIA Adapter. Next, the Stop a Hardware Device dialog box appears. Click OK. You can now unplug the Card. The computer will beep indicating the Card was unplugged. If the sound on your computer is turned on you will hear one beep. Note: Remove the PC Card from the PC before storing the PC in a computer case. Also, turn the antenna to its original down position. Leaving the card in the PC or the antenna in the upright position while storing the PC in a computer case may damage the card or the antenna.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 13 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Indicator Light Troubleshooting Installing Navini Diagnostics (NavDiag) Software An indicator light on the top of the PC Card’s black encasement provides information about the Card’s operation. When the light is solid, the Card is trying to synchronize with a BTS. When the light blinks, the Card has acquired synchronization with a Base Station. If you experience difficulties with your Internet connection after you have installed the PC Card driver software, please review the Minimum Computing Requirements and Addendum 1 in this User Guide to ensure your computer meets those requirements. Next, go back over the installation procedures and ensure all steps were completed properly. Assuming the computer requirements are met and the installation steps were completed as required, you may need to install the Navini Diagnostics software. The Navini Diagnostics software assists in solving connection problems. This software is provided on the Installation CD that came in your PC Card package. The Navini Diagnostics software enables you to troubleshoot signal issues, network connections, and power problems. Two important types of information it provides are signal strength and quality of the incoming signal. It can also provide information about the connectivity to the Service Provider’s network. Before you install your NavDiag software, please note: For Windows 2000 you must be logged into an account having Administrative privileges in order to install the Navini Diagnostics software. For Windows 98SE Operating Systems (OS), the Windows OS CD may be required to complete the installation. If prompted, insert the OS CD into the drive and accept the defaults. Indicator Light
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 14 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Installing Navini Diagnostics (NavDiag) Software, continued If you are going to upgrade your PC Operating System after loading the Navini Diagnostics software, you must first uninstall NavDiag prior to upgrading the OS. Otherwise, NavDiag will not work. See Uninstall instructions in this Guide. Note: The screenshots shown in these instructions were taken from a laptop with Windows 2000. If you have a Windows 98, XP, or ME operating system, the screens you see may vary from the screens shown in the instructions. • Step Action Illustration 1. Shut down all programs, including anti-virus software programs, before installing the NavDiag software. 2. Insert the Installation CD into the CD-ROM drive. 3. Open the CD by clicking on the My Computer icon. Double-click on the folder named Navini_Diagnostics. 4. Double-click on the icon for the file navdiag_windows.exe*. This will automatically start the installation of NavDiag. Example 5. The InstallAnywhere window appears. The progress bar indicates that InstallAnywhere has initialized. Windows 2000 Screen Doubleclickthis file.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 15 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Installing Navini Diagnostics (NavDiag) Software, continued *NOTE: In step 6, your version of NavDiag may automatically attempt to match the language set on your PC under Regional Options. The language selection affects how NavDiag displays its screens. If you receive an error message concerning the language, click OK and NavDiag will default to English. At this time, NavDiag supports three languages: 1. English (U.S.), 2.Spanish (Spain), and 3. Dutch (Holland). Step Action Illustration 6. The Navini Diagnostics Language screen appears* (see Note above). Select a language, and click OK to continue. Windows 2000 Screen 7. The progress bar indicates the files are being installed. Windows 2000 Screen 8. The NavDiag Introduction screen appears. Click Next to continue. Windows 2000 Screen
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 16 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Installing Navini Diagnostics (NavDiag) Software, continued Step Action Illustration 9. The License Agreement screen appears. Read the Licensing Agreement. Select the I Accept option, and click Next to continue. If the License Agreement is not accepted, you cannot install the software. Windows 2000 Screen 10. The Choose Install Folder screen appears. Enter the name of the folder where you wish to install the software. Click Next to continue. The default installation folder provided by the software is shown in the illustration. Windows 2000 Screen 11. The Choose Shortcut Folder screen appears. Accept the default and click Next to continue. Windows 2000 Screen
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 17 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Installing the Navini Diagnostics (NavDiag) Software, continued Step Action Illustration 12. The Pre-Installation Summary screen appears. Review the contents for accuracy. Click Install to continue. For your installation and computer, this screen may have different information than what is shown in the illustration.Windows 2000 Screen 13. The Installing screen will change as the application files are loaded. Windows 2000 Screen 14. At the Install Complete screen, click Done to close the window. Windows 2000 Screen
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 18 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Using Navini Diagnostics To open the Navini Diagnostics software application, double-click on the Navini Diagnostics icon on your desktop. Navini Diagnostics.lnk The Connection Status screen will open and display data if the Card is in use. The screen will refresh live data every second. Looking from left to right, the icons represent the PC, the connection between the PC and the PC Card or Desktop Modem (pictured), the PC Card or Modem, the connection between the Card and the Base Station, and the Base Station with which the Card is communicating. Check marks over the connections indicate working connections. If the connection between the PC and the Card or between the Card and the Base Station is interrupted, an “X” is positioned over the corresponding icon.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 19 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Using Navini Diagnostics, continued The Signal Strength and Signal Quality are dynamic bar areas that indicate how well your PC Card is receiving signals from the Base Station. In particular, the Signal Strength bar area graphically represents the strength of the Absolute BTS Synchronization Signal received by the PC Card. The strength of the signal is represented by a group of colored bars. The higher the pile of bars goes, the stronger the signal. The color of the bars also gives an indication of the strength of the signal. Green lines indicate an excellent signal. Orange lines indicate a good signal, while red lines indicate a weak signal. The Signal Quality bar area graphically represents the Signal-to-Noise Ratio (SNR) of the downlink access code channel (ACC) received by the PC Card. Again, the quality of the signal is represented by a group of colored bars. The higher the pile of bars goes, the better the SNR of the signal. The color of the bars also gives an indication of the quality of the signal. Green lines indicate high quality signal. Orange lines indicate a good quality signal while red lines indicate a low quality signal. To increase the strength and quality of the signal, change the location of the PC in which the PC Card is inserted. Try moving it closer to a window, to a higher location, away from other wireless devices (microwave ovens, cordless phones), and away from metal objects (shelves, file cabinets). As the PC is repositioned, observe the Signal Strength and Quality bars. Position the Card for maximum signal strength and quality.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 20 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Using Navini Diagnostics, continued The History graphs plot the change in signal strength and signal quality over time. The graphs cover the last minute and are updated every second. Read the graphs from right to left. The right side of the graph represents the most recent status of your PC Card. At the bottom of the Connection Status screen are four parameters. These parameters are BTS ID, Network ID, Active SW Version, and Standby SW Version. The BTS ID and Network ID indicate the BTS to which the PC Card is currently synchronized and the network in which the PC Card is operating. Active SW Version and Standby SW Version indicate the version number of the software currently loaded in the “active side” and “standby side” of the PC Card’s flash memory. The two letters in parenthesis following the release number indicate the type of software load. JD indicates Joint Detection while EN indicates Enhanced Nulling. On the left-hand side of the screen are five screen options:  Connection Status  Configuration  Trend Analysis  Statistics  About
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 21 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Using Navini Diagnostics, continued The following screen appears when you select Configuration. This screen enables you to update your Card’s software, if directed to do so by your Service Provider. The “Allow Customer Satisfaction Reporting” feature is not currently supported in the PC card. The Trend Analysis screen enables you to view Card parameters that evolve over time. With this screen, you can select up to three parameters to plot. By pressing the Plot Graph button, the following screen will appear. This screen displays the value of the selected parameters over the last five minutes, updated once every second. The graphic scrolls from right to left.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 22 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Using Navini Diagnostics, continued To view the Statistics screen, press the Statistics button. The Statistics screen enables you to view the current value of selected parameters, which are updated as they change over time. The About screen provides vital information such as the version of the Navini Diagnostics software currently installed on your computer. It also provides a website address and telephone number where you can contact your Service Provider. An example of the About screen follows.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 23 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Using Navini Diagnostics, continued Uninstalling Navini Diagnostics Software A Help button appears on the top right corner of all the NavDiag windows. The Help button gives you two options. The first option, On NavDiag, provides help text on the functionality of the NavDiag program. The second option, About NavDiag, is equivalent to clicking on the About icon. If for some reason you need to uninstall the NavDiag software, e.g., to upgrade your Operating System software, follow the procedure below. Note: The screenshots shown in these instructions were taken from a laptop with Windows 2000. If you have a Windows 98, XP, or ME operating system, the screens you see may vary from the screens shown in the instructions. Step Action Illustration 1. On your computer screen lower left corner, click on Start > Programs > NavDiag > Uninstall. Windows 2000 Screen
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 24 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Uninstalling NavDiag Software, continued Optional Desktop Antenna Step Action Illustration 2. The Install-Anywhere Uninstaller screen appears. Click Uninstall. Windows 2000 Screen 3. The screen will indicate the application files are uninstalled. Windows 2000 Screen 4. The Uninstall Complete screen appears when finished. Click on Quit to close the Uninstall screen. Windows 2000 Screen 5. Restart the PC to complete the uninstall process. This will ensure it functions properly after uninstalling. An optional desktop antenna is available for the Ripwave Wireless Broadband Access Card. This antenna connects to the PC Card and then sits on a surface next to the laptop. This antenna should be used if optimal reception can not be obtained through the PC Card antenna. Following is a picture of the optional desktop antenna.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 25 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Optional Desktop Antenna, continued Care and Maintenance To connect the desktop antenna to the PC Card, you must first remove the antenna attached to the PC Card. To remove the antenna, grasp the base of the antenna near its connection point and then firmly pull the antenna away from the card. Do not grasp the top or middle of the antenna as it may break when you try to pull the antenna away. Once the PC Card antenna is removed, connect the desktop antenna by inserting its connector into the port on the PC Card. If a desktop antenna is required for optimal reception, avoid frequently connecting and disconnecting the desktop antenna from the PC Card as frequent connection/disconnection may cause the connector on the desktop antenna to break. The Ripwave Wireless Broadband Access Card is designed to give years of trouble-free service. To ensure operation, read the following care and maintenance instructions.  Keep the PC Card free of dust and moisture. If the Card gets wet, use a towel to dry it immediately.  Handle the PC Card gently. Dropping it or mishandling it can cause damage to the metal/plastic shell or the electronic circuitry.  Keep the PC Card away from high temperatures. Heat can cause damage to the metal/plastic shell or the electronic circuitry.  To clean the external areas of the PC Card, use only an electrical contact cleaner that is non-conductible and a soft, damp, lint-free cloth. Do not use any chemicals or abrasives to clean the Card. Also use caution around the connection pins.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 26 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Care and Maintenance, continued Upgrading the PC Card  If there is a problem with the Card, do not attempt to repair it yourself. Report the problem to your Service Provider.  Do not apply adhesive labels to the Card. This may cause the card to become jammed inside the card slot.  The PC Card should fit easily into the PC slot. Do not force the card into the PC slot. Forcing the card into the slot may cause damage to the connector pins.  If you are going to upgrade your computer Operating System after loading the NavDiag software, you must first uninstall NavDiag prior to upgrading the OS. Otherwise, NavDiag will not work. See Uninstall instructions in this Guide. There are two different ways to upgrade the software that makes the PC Card work. Your Service Provider may perform an over-the-air (OTA) upgrade, where the up-to-date software files are transferred wirelessly from a Base Station to your Card; or the Provider may provide a downloadable web file or CD-ROM with software that is installed on your PC and used to upgrade the Card software. The latter method is used only if the PC Card was not inserted and “on” during the OTA upgrade process. The OTA upgrade is normally transparent to the user; in other words, there should be no noticeable service interruption. The web or CD upgrade comes with instructions and takes a minimal amount of time to complete.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 27 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) ADDENDUM 1: PC Card - PC Troubleshooting - For Use With the Ripwave Wireless Broadband Access Card & Navini Diagnostics Software - PC Operating Systems Prior to installing the Navini Diagnostics (NavDiag) software, please check to ensure that the PC Operating System meets the criteria given in the table below. If these criteria are not met, unpredictable problems may occur as a result of installation. It is recommended that the user have the latest Windowsc updates installed prior to installing the NavDiag software. Operating System PC Card Interface Notes Win98, 2nd edition Supported 1 WinME Supported 1 Win 2000 Supported 1, 3 Win XP Supported 2, 3 Note 1: Internet Explorer 3.0 or higher is required Note 2: Requires Service Pack 1 Note 3: To load the NavDiag software, the user MUST have Administrative privileges. Results of Correct NavDiag Installation Experienced PC users can check the results of the Navini Diagnostics installation by looking at the log file that is created during the installation process. The log file is named “Ripwave_Diagnostics_InstallLog.log.” It is located under c:\Program Files\Navini Diagnostics. ------- Install Begin: Tue Jul 20 12:15:22 CDT 2004 Install End: Tue Jul 20 12:15:30 CDT 2004 Created with Zero G's InstallAnywhere 4.5.3 Enterprise Build 1394 Summary ------- Installation: Successful with warnings. 2 SUCCESSES 1 WARNINGS 0 NONFATAL ERRORS 0 FATAL ERRORS Action Notes: None.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 28 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Install Log Detail: Check Disk Space: C:\Program Files\NavDiag Status: SUCCESSFUL Additional Notes: NOTE - Required Disk Space: 29,363,315; Free Disk Space: 30,806,179,840 Install Directory: C:\Program Files\NavDiag\ Status: SUCCESSFUL Get Registry Entry: Key: HKEY_LOCAL_MACHINE\SOFTWARE\Navini Networks\NavDiag, ValueName: InstallDirectory Status: WARNING Additional Notes: WARNING - Win32Exception Make Registry Entry: Key: HKEY_LOCAL_MACHINE\SOFTWARE\Navini Networks, Value Name: , Value Data: Status: SUCCESSFUL Make Registry Entry: Key: HKEY_LOCAL_MACHINE\SOFTWARE\Navini Networks\NavDiag, Value Name: , Value Data: Status: SUCCESSFUL Make Registry Entry: Key: HKEY_LOCAL_MACHINE\SOFTWARE\Navini Networks\NavDiag, Value Name: InstallDirectory, Value Data: C:\Program Files\NavDiag Status: SUCCESSFUL Install Directory: C:\Program Files\NavDiag\Uninstall\ Status: SUCCESSFUL Install Uninstaller: Navini Diagnostics (Install All Uninstaller Components) Status: SUCCESSFUL Install Directory: C:\Program Files\NavDiag\jre Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\Uninstall\Uninstall NavDiag.exe Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\Uninstall\Uninstall NavDiag.lax Status: SUCCESSFUL Install Directory: C:\Program Files\NavDiag\Uninstall\resource\ Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\Uninstall\resource\iawin32.dll Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\Uninstall\resource\remove.exe Status: SUCCESSFUL Make Registry Entry: Key: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\Navini Diagnostics, Value Name: DisplayName, Value Data: Navini Diagnostics
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 29 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Status: SUCCESSFUL Make Registry Entry: Key: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\Navini Diagnostics, Value Name: UninstallString, Value Data: "C:\Program Files\NavDiag\Uninstall\Uninstall NavDiag.exe" Status: SUCCESSFUL Install Uninstaller: Navini Diagnostics (Install All Uninstaller Components) Status: SUCCESSFUL Create LaunchAnywhere: Navini Diagnostics.exe (Install All LaunchAnywhere Java Executable Components) Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\Navini Diagnostics.exe Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\Navini Diagnostics.lax Status: SUCCESSFUL Create LaunchAnywhere: Navini Diagnostics.exe (Install All LaunchAnywhere Java Executable Components) Status: SUCCESSFUL Install Directory: C:\Program Files\NavDiag\data\ Status: SUCCESSFUL Install Directory: C:\Program Files\NavDiag\data\images\ Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\data\images\billboard.gif Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\data\images\splash.gif Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\data\images\buttonbar.gif Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\data\images\about2.gif Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\data\images\about1.gif Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\data\images\about.gif Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\data\images\uninstall.gif Status: SUCCESSFUL Install Directory: C:\Program Files\NavDiag\data\log\ Status: SUCCESSFUL Install Directory: C:\Program Files\NavDiag\data\lib\ Status: SUCCESSFUL
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 30 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) Install File: C:\Program Files\NavDiag\data\lib\ctl.jar Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\data\lib\navDiag.jar Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\data\lib\jfreechart-0.9.13.jar Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\data\lib\jcommon-0.8.8.jar Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\data\lib\log4j.jar Status: SUCCESSFUL Install Directory: C:\Program Files\NavDiag\data\doc\ Status: SUCCESSFUL Install Directory: C:\Program Files\NavDiag\config\ Status: SUCCESSFUL Install File: C:\Program Files\NavDiag\config\NavDiag.lcf Status: SUCCESSFUL Install Directory: C:\Documents and Settings\luis\Start Menu\Programs\NavDiag\ Status: SUCCESSFUL Create Shortcut: C:\Documents and Settings\luis\Start Menu\Programs\NavDiag\Navini Diagnostics.lnk Status: SUCCESSFUL Create Shortcut: C:\Documents and Settings\luis\Start Menu\Programs\NavDiag\Uninstall.lnk Status: SUCCESSFUL Install Directory: C:\Documents and Settings\luis\Desktop\ Status: SUCCESSFUL Additional Notes: NOTE - Directory already existed Create Shortcut: C:\Documents and Settings\luis\Desktop\Navini Diagnostics.lnk Status: SUCCESSFUL
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 31 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) ADDENDUM 2: End User Software License Agreement between Navini Networks, Inc. and Buyer ARTICLE 1 IMPORTANT MESSAGE 1.1 Act of Assent. Installing the Software indicates that you have read, understand and accept this License Agreement. ARTICLE 2 LICENSES 2.1 Grant of License. The Software and related Documentation, are the intellectual property of Navini Networks, Inc. and are protected by law. Navini Networks, Inc. grants to Buyer a personal, nonexclusive, nontransferable worldwide license, for revocable use (as permitted herein) of the Software based on the terms and conditions of this License Agreement and the Master Supply Agreement to which it is attached. Buyer is permitted to install and use the Software on its server, but only in conjunction with the Navini Hardware. Buyer is not permitted to rent, sell or otherwise transfer the Software to any third parties. 2.2 Ownership Rights. Under this Agreement, Buyer does not acquire any rights of ownership in the Software and related Documentation and subsequent releases and versions licensed by Navini Networks, Inc. to Buyer pursuant to this License Agreement, whether in printed or machine-readable format. Buyer acquires only the right to use the Software and related Documentation subject to the terms and conditions of this Agreement. Buyer promises to keep the Software in confidence for the benefit of Navini Networks, Inc. and agrees to destroy or return the Software and all copies at such time as Buyer chooses to cease using the Software or upon termination or cancellation of this License Agreement for any reason. 2.3 Backup Copies. Buyer may copy the Software for safekeeping (archival) or backup purposes, provided that all such copies of the Software are subject to the provisions of this License Agreement, and also provided that each copy shall include in readable format any and all confidential, proprietary, and copyright notices or markings contained in the original. 2.4 Assignment. The rights granted in this License Agreement are restricted for use solely by Buyer and may not be assigned, transferred, or sublicensed, however Buyer may grant access to its server to End-Users. Each Buyer shall be authorized to make use of the Software in the form in which it is provided to Buyer solely for Buyer’s own computer server location. Buyer represents that it will not use the Software for any purpose that is not expressly delineated in this Agreement. Further Buyer represents that it will comply with all export, re-export, and other laws in its use of the Software.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 32 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) 2.5 Suitability. a. Buyer alone is responsible for determining which software best suits Buyer’s needs, for installing and operating the Software, and for the results obtained. Accordingly, each Buyer should determine its needs, and evaluate the Software’s capabilities before making a final decision about licensing the software. b. Navini Networks, Inc. makes no representation that the Software conforms to or satisfies any federal, state, or local laws. Buyer is encouraged to engage professional assistance from attorneys and engineers to evaluate the suitability of the Software for Buyer’s use. c. Navini Networks, Inc. makes no claims that the Software is suitable for Buyer’s intended purposes. 2.6 Remote Digital Access. Navini Networks, Inc. reserves the right, but is not obligated to digitally access the Software for the purposes of upgrading and maintaining the Software. 2.7 U.S. GOVERNMENT RESTRICTED RIGHTS. All Software provided to the U.S. Government pursuant to solicitations issued on or after December 1, 1995 is provided with the commercial license rights and restrictions described elsewhere herein. All Software provided to the U.S. Government pursuant to solicitations issued prior to December 1, 1995 is provided with “Restricted Rights” as provided for in FAR, 48 CFR 52.227-14 (June 1987) or DFAR, 48 CFR 252.227-7013 (Oct 1988), as applicable ARTICLE 3 TRADE SECRETS 3.1 Trade Secret. Navini Networks, Inc. considers the licensed Software covered by this License Agreement to be a trade secret. Navini Networks, Inc. does not disclose any information to Navini Networks, Inc. competitors or potential competitors. Buyer shall not disclose any design, code, or technological know-how gained by access to the Software to Licensor’s competitors. Buyer shall not use design, code, or documentation gained by access to the Software to develop a similar technology or a competing software product. To attempt to or to do so, the Parties acknowledge, understand and agree, constitute a material breach of this License Agreement. 3.2 Third Party Intellectual Property. Buyer acknowledges, understands and agrees that the licensed Software covered by this License Agreement may contain Intellectual Property owned by Third Parties and duly licensed to Navini Networks, Inc. Copyright, Patent and other laws protect Third Party Intellectual Property manufactured with, marketed with, or otherwise bundled with the licensed Software. Buyer promises to keep such Third Party Intellectual Property in confidence to the benefit of the Third Party, agrees not to reverse engineer or otherwise decompile Third Party Intellectual Property, and agrees to stop using, destroy and/or return such Third Party owned Intellectual Property under the same terms and conditions as the licensed Software as set forth in this License Agreement.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 33 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) ARTICLE 4 INDEMNIFICATIONS AND WARRANTY 4.1 Intellectual Property Indemnification; Entire Liability. ARTICLE 15 OF THE SUPPLY AGREEMENT TO WHICH THIS AGREEMENT IS ATTACHED STATES THE ENTIRE LIABILITY OF NAVINI NETWORKS, INC. WITH RESPECT TO INFRINGEMENT OF COPYRIGHTS, TRADE SECRETS, TRADEMARKS, PATENTS, AND OTHER INTELLECTUAL PROPERTY RIGHTS BY THE LICENSED SOFTWARE, DOCUMENTATION, OR ANY PARTS THEREOF, AND NAVINI NETWORKS, INC. SHALL HAVE NO ADDITIONAL LIABILITY WITH RESPECT TO ANY ALLEGED OR PROVEN INFRINGEMENT. 4.2 Warranty. EXCEPT AS GRANTED IN THE BODY OF THE SUPPLY AGREEMENT TO WHICH THIS LICENSE AGREEMENT IS ATTACHED, THE LICENSED SOFTWARE IS PROVIDED BY NAVINI NETWORKS, INC. “AS IS” AND WITHOUT WARRANTY OF ANY KIND OR NATURE, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING (WITHOUT LIMITATION) THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THIS LIMITATION OF WARRANTIES WAS A MATERIAL FACTOR IN THE ESTABLISHMENT OF THE LICENSE FEE CHARGED FOR EACH SPECIFIC ITEM OF SOFTWARE LICENSED. ARTICLE 5 LIMITATION OF LIABILITY 5.1 Consequential Damages. TO THE MAXIMUM EXTENT PERMITTED BY THE APPLICABLE LAW, IN NO EVENT SHALL NAVINI NETWORKS, INC. OR ANY THIRD PARTY INVOLVED IN THE CREATION, PRODUCTION, DELIVERY, OR LICENSING OF THE SOFTWARE BE LIABLE FOR ANY LOST REVENUES, PROFITS OR DATA OR OTHER SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES, HOWEVER CAUSED AND REGARDLESS OF THEORY OF LIABILITY, EVEN IF NAVINI NETWORKS, INC. HAS, OR SHOULD HAVE HAD ANY KNOWLEDGE, ACTUAL OR CONSTRUCTIVE, OF THE POSSIBILITY OF SUCH DAMAGES. 5.2 License-Fee Limitation. Except for the indemnification provisions of Article 15, Navini Networks, Inc.’s maximum liability for damages is limited to the license fees paid by Buyer under this Agreement for the particular licensed Software that caused the damages. 5.3 Loss of Data. Software error can cause a significant loss of data. Navini Networks, Inc. shall not be responsible for any loss of data. Navini Networks, Inc.’s responsibility is to correct the Software error as provided in this License Agreement or the Supply Agreement to which it is attached. It is Licensee’s responsibility to have adequate backup procedures to protect Buyer from significant loss of valid data.
Navini Networks, Inc. Ripwave Wireless Broadband Access Card User’s Guide Page 34 050525_pv1.2_PC_Card_User’s_Guide_40-00292-00b(4.3) ARTICLE 6 OBJECT CODE ONLY-NO MODIFICATIONS 6.1 Modifications. In order to maintain the “trade secret” status of the information contained in the Licensed Software, Navini Networks, Inc. provides the Software in object-code form only. Buyer shall not modify, enhance, adapt, disassemble, translate, decompile or otherwise decode any portion of the object code of the Software module. Buyer shall not use the Software without a license to the Software object code. The object code contains the license number, date of license, and other license information. This information is placed in the object-code portions to prevent unauthorized and unlicensed distributions of the Software. Buyer shall not subvert or change any of this information. Further Buyer shall not make, full or partial, copies of any documentation whether printed or machine- readable media supplied with the Licensed Software unless expressly granted prior written permission by Navini Networks, Inc. 6.2 Responsibility for Damages. Buyer is subject to the provisions of the Supply Agreement with respect to the Software (including Section 16). Buyer is fully liable and responsible for any damages, indirect or direct, and costs that Navini Networks, Inc. may incur if Buyer appoints a subcontractor who accesses the Software without Navini’s prior written consent. Buyer shall defend, indemnify, and hold Navini Networks, Inc., its directors, officers, employees, agents, Authorized Partners, and other representatives harmless accordingly for all costs and direct and indirect damages sustained by Navini Networks, Inc. However, if the subcontractor is pre-approved by Navini in writing for access to the Software, then this Section shall not apply. 6.3 Copyright Notices. Buyer shall not remove any copyright or proprietary rights notice or identification that indicates Navini Networks, Inc. ownership from any part of the licensed Software, it being expressly understood and agreed that the existence of such copyright notice should not be construed as an admission or presumption that publication of the licensed Software has occurred. END OF AGREEMENT Copyright © 2004-2005 Navini Networks, Inc. All rights reserved. Printed in the USA. Navini Networks is a registered trademark. Zero-Install, Ripwave, and Unwired by Navini are trademarks of Navini Networks, Inc. Other product and company names mentioned herein may be trademarks and/or service marks of their respective owners. Rev. 052302

Navigation menu