Cisco Systems 825321596 Beacon Point Module User Manual
Cisco Systems Inc Beacon Point Module
Users Manual
REVIEW DRAFT - CISCO CONFIDENTIAL Cisco Beacon Hardware Installation Guide First Published: 2016-09-28 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http:// www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R) © 2016 Cisco Systems, Inc. All rights reserved. CONTENTS Preface Preface v Audience v Conventions v Related Documentation vi Obtaining Documentation and Submitting a Service Request vi CHAPTER 1 About Cisco Beacon Point Module 1 Supported Access Points 3 Cisco Beacon Point Module Features 3 Technical Specifications 3 Cisco Beacon Point Module Model Number 4 Installing a Cisco Beacon Point Module on an Access Point 4 Checking the Cisco Beacon Point Module LEDs 9 CHAPTER 2 Declarations of Conformity and Regulatory Information 11 Manufacturers Federal Communication Commission Declaration of Conformity Statement 12 VCCI Statement for Japan 13 Guidelines for Operating Cisco Virtual Beacon in Japan 13 Japanese Translation 13 English Translation 13 Canadian Compliance Statement 14 Statement 371—Power Cable and Power Injector 15 Industry Canada 15 This Device Meets FCC and International Guidelines for Exposure to Radio Waves 15 This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves 16 Cet appareil est conforme aux directives internationales en matière d'exposition aux fréquences radioélectriques 16 Cisco Beacon Hardware Installation Guide iii Contents REVIEW DRAFT - CISCO CONFIDENTIAL Additional Information on RF Exposure 17 Declaration of Conformity Statements 17 Cisco Beacon Hardware Installation Guide iv Preface • Audience, page v • Conventions, page v • Related Documentation, page vi • Obtaining Documentation and Submitting a Service Request, page vi Audience This document is for Connected Mobile Experiences (CMX) network and IT administrators who deploy Cisco Beacon Points or Cisco Beacon Point Modules for high accuracy virtual beacon solution. Conventions This document uses the following conventions: Table 1: Conventions Convention Indication bold font Commands and keywords and user-entered text appear in bold font. italic font Document titles, new or emphasized terms, and arguments for which you supply values are in italic font. [] Elements in square brackets are optional. {x | y | z } Required alternative keywords are grouped in braces and separated by vertical bars. [x|y|z] Optional alternative keywords are grouped in brackets and separated by vertical bars. string A nonquoted set of characters. Do not use quotation marks around the string. Otherwise, the string will include the quotation marks. courier font Terminal sessions and information the system displays appear in courier font. Cisco Beacon Hardware Installation Guide Preface Related Documentation REVIEW DRAFT - CISCO CONFIDENTIAL Note Tip Caution Convention Indication <> Nonprinting characters such as passwords are in angle brackets. [] Default responses to system prompts are in square brackets. !, # An exclamation point (!) or a pound sign (#) at the beginning of a line of code indicates a comment line. Means reader take note. Notes contain helpful suggestions or references to material not covered in the manual. Means the following information will help you solve a problem. Means reader be careful. In this situation, you might perform an action that could result in equipment damage or loss of data. Related Documentation For more information about Cisco CMX Cloud, see: https://support.cmxcisco.com/hc/en-us Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and gathering additional information, see What's New in Cisco Product Documentation. To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the What's New in Cisco Product Documentation RSS feed. RSS feeds are a free service. Cisco Beacon Hardware Installation Guide vi CHAPTER About Cisco Beacon Point Module Cisco Beacon Point Module (AIR-RM-VBLE2-K9=) is a Bluetooth Low Energy (BLE version v4.2) beacon module that is mounted on supported Access Points. The access points now act as integrated WiFI and Bluetooth devices or Bluetooth-integrated access points. The smart device receives signals of different strengths from multiple Bluetooth-integrated access points. Deploying Bluetooth-integrated access points is similar to any Wi-Fi location based service solution. The recommended density for deploying the Bluetooth-integrated access points is 1 per 2500 sq.ft. The recommended height for a Bluetooth-integrated access points is 13 ft (3.9 m). Cisco Beacon Center requires the correct physical orientation, position, and height of Bluetooth-integrated access points for providing clients with indoor navigation, turn-by-turn guidance and proximity messaging for best indoor navigation experience. Bluetooth-integrated access pointss connect with Cisco Beacon Center over the internet using secure HTTPS protocol. Each Bluetooth-integrated access points has a unique IP address just like any enterprise grade networking device. Bluetooth-integrated access points should connect with Cisco Beacon Center for Cisco Beacon Hardware Installation Guide About Cisco Beacon Point Module REVIEW DRAFT - CISCO CONFIDENTIAL management and control. For Bluetooth-integrated access points to communicate with the Cisco Beacon Center the port numbers 80 (TCP) and 443 (TCP, UDP) must be open. Figure 1: Cisco Beacon Point Module (AIR-RM-VBLE2-K9=) • Supported Access Points, page 3 • Cisco Beacon Point Module Features, page 3 • Technical Specifications, page 3 Cisco Beacon Hardware Installation Guide About Cisco Beacon Point Module Supported Access Points REVIEW DRAFT - CISCO CONFIDENTIAL • Cisco Beacon Point Module Model Number, page 4 • Installing a Cisco Beacon Point Module on an Access Point, page 4 • Checking the Cisco Beacon Point Module LEDs, page 9 Supported Access Points The Cisco Beacon Point Module can be attached to the following access points: • AP3802I • AP3802E Cisco Beacon Point Module Features Cisco Beacon Point Module comes with the following features: Table 2: Hardware Feature Summary Feature Description LED indicators A multicolor system status LED on the front-face of the unit. Reset button A recessed button that resets a Cisco Beacon Point Module to factory settings when the Bluetooth-integrated access points is powered up. Power Options Uses the power supply of the access point. Technical Specifications NEED IMAGE HERE Table 3: Technical Specifications of Cisco Beacon Point Module Feature Description Dimensions (of access point with Cisco Beacon Point 275 mm x 284.7 mm x 60.5 mm Module) 10.8 in x 11.2 in x 2.38 in Weight 1.38 kg (3.06 lbs) Cisco Beacon Hardware Installation Guide About Cisco Beacon Point Module Cisco Beacon Point Module Model Number REVIEW DRAFT - CISCO CONFIDENTIAL Feature Description Compliance standards UL 60950-1 CAN/CSA-C22.2 No. 60950-1 FCC Part 15.247, 15.107, and 15.109 FCC Part 15 Class B RSS-247 ICES-003 (Canada) ClassB EMC compliance Environmental Fanless operation; passive cooling Nonoperating (storage) temperature: -30 to 70℃ (-22 to 158℉) Operating temperature: 0 to 40℃ (32 to 104℉) Operating humidity: 10 to 90% (noncondensing) Operating altitude: 9843 ft (3000 m) Power Dissipation Less than 4.5W Cisco Beacon Point Module Model Number Cisco Beacon Point Module is available in the following model: Table 4: Cisco Beacon Point Module Model Number Product ID Description AIR-RM-VBLE2-K9= Cisco Beacon Point Module with internal antennas that can be mounted on supported access points. Installing a Cisco Beacon Point Module on an Access Point These instructions demonstrate how to install a Cisco Beacon Point Module to an access point that is already mounted to its location using a bracket. Cisco Beacon Hardware Installation Guide About Cisco Beacon Point Module Installing a Cisco Beacon Point Module on an Access Point REVIEW DRAFT - CISCO CONFIDENTIAL Before You Begin Ensure that Access Point is already mounted to the celing using a bracket. Step 1 Close the hinged door of the Cisco Beacon Point ModuleUnscrew the hinged door or the Cisco Beacon Point Module and swing it open. Cisco Beacon Hardware Installation Guide About Cisco Beacon Point Module Installing a Cisco Beacon Point Module on an Access Point REVIEW DRAFT - CISCO CONFIDENTIAL Step 2 Slide the Cisco Beacon Point Module into the access point. Step 3 Close the hinged door of the Cisco Beacon Point Module Cisco Beacon Hardware Installation Guide About Cisco Beacon Point Module Installing a Cisco Beacon Point Module on an Access Point REVIEW DRAFT - CISCO CONFIDENTIAL Step 4 Screw in the inset screw on the Cisco Beacon Point Module to secure the hinged door to the rest of the module. Cisco Beacon Hardware Installation Guide About Cisco Beacon Point Module Installing a Cisco Beacon Point Module on an Access Point REVIEW DRAFT - CISCO CONFIDENTIAL Cisco Beacon Hardware Installation Guide About Cisco Beacon Point Module Checking the Cisco Beacon Point Module LEDs REVIEW DRAFT - CISCO CONFIDENTIAL Checking the Cisco Beacon Point Module LEDs Figure 2: Face of Cisco Beacon Point Module Note Location of the Status LED Small variations in color intensity and hue will be present from unit to unit. This is within the normal range of the LED manufacturer’s specifications, and is not a defect. Cisco Beacon Point status LED indicates various conditions, which are described in the table below: Cisco Beacon Hardware Installation Guide About Cisco Beacon Point Module Checking the Cisco Beacon Point Module LEDs REVIEW DRAFT - CISCO CONFIDENTIAL Table 5: Cisco Beacon Point LED Status Indication LED Color Cisco Beacon Point LED Status Blinking red Cisco Beacon Point Module beginning a boot reset. Alternating green and yellow Cisco Beacon Point Module booting. White Cisco Beacon Point Module connecting to Cisco Beacon Center. Green Cisco Beacon Point Module configured by Cisco Beacon Center. Blinking orange Cisco Beacon Point Module upgrading. Alternating green and purple Locating a Cisco Beacon Point Module in Cisco Beacon Center. Blinking amber Cisco Beacon Point Module failure mode. OFF turning to red Reset to factory default button pressed by the user. White turning to OFF Cisco Beacon Point Module about to reset. Cisco Beacon Hardware Installation Guide 10 CHAPTER Declarations of Conformity and Regulatory Information This section provides declarations of conformity and regulatory information for the Cisco Beacon Point. You can find additional information at this location • Manufacturers Federal Communication Commission Declaration of Conformity Statement, page 12 • VCCI Statement for Japan, page 13 • Guidelines for Operating Cisco Virtual Beacon in Japan, page 13 • Canadian Compliance Statement, page 14 • Statement 371—Power Cable and Power Injector, page 15 • Industry Canada, page 15 • This Device Meets FCC and International Guidelines for Exposure to Radio Waves, page 15 • This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves, page 16 • Cet appareil est conforme aux directives internationales en matière d'exposition aux fréquences radioélectriques, page 16 • Additional Information on RF Exposure, page 17 • Declaration of Conformity Statements, page 17 Cisco Beacon Hardware Installation Guide 11 Declarations of Conformity and Regulatory Information Manufacturers Federal Communication Commission Declaration of Conformity Statement REVIEW DRAFT - CISCO CONFIDENTIAL ManufacturersFederalCommunicationCommissionDeclaration of Conformity Statement Table 6: Cisco Beacon Point Models and Certification Numbers Cisco Beacon Point Models Certification Number Cisco Beacon Point LDK102111 Cisco Beacon Point Module LDK825321596 Manufacturer: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA This device complies with Part 15 rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna • Increase separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Cisco may void the user’s authority to operate the equipment Cisco Beacon Hardware Installation Guide 12 Declarations of Conformity and Regulatory Information VCCI Statement for Japan REVIEW DRAFT - CISCO CONFIDENTIAL Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency when using the integrated antennas. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device. VCCI Statement for Japan Caution This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Guidelines for Operating Cisco Virtual Beacon in Japan This section provides guidelines for avoiding interference when operating Cisco Virtual Beacon in Japan. These guidelines are provided in both Japanese and English. Japanese Translation English Translation This equipment operates in the same frequency bandwidth as industrial, scientific, and medical devices such as microwave ovens and mobile object identification (RF-ID) systems (licensed premises radio stations and unlicensed specified low-power radio stations) used in factory production lines. Cisco Beacon Hardware Installation Guide 13 Declarations of Conformity and Regulatory Information Canadian Compliance Statement REVIEW DRAFT - CISCO CONFIDENTIAL 1 Before using this equipment, make sure that no premises radio stations or specified low-power radio stations of RF-ID are used in the vicinity. 2 If this equipment causes RF interference to a premises radio station of RF-ID, promptly change the frequency or stop using the device; contact the number below and ask for recommendations on avoiding radio interference, such as setting partitions. 3 If this equipment causes RF interference to a specified low-power radio station of RF-ID, contact the number below. Contact Number: 03-6434-6500 Canadian Compliance Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Table 7: Antenna Specifications Antenna Frequency Antenna Peak Gain Antenna Impedance 2.4 GHz 5 dBi 50 ohms Table 8: Antenna Specifications for module Antenna Frequency Antenna Peak Gain Antenna Impedance 2.4 GHz 5.8 dBi 50 ohms Cisco Beacon Hardware Installation Guide 14 Declarations of Conformity and Regulatory Information Statement 371—Power Cable and Power Injector REVIEW DRAFT - CISCO CONFIDENTIAL Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Statement 371—Power Cable and Power Injector When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO. The use of cables that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the code) is not limited to CISCO-designated products. Industry Canada Table 9: Cisco Beacon Point Models and Certification Numbers Cisco Beacon Models Certification Number AIR-VBLE1-K9 2461B-102111 AIR-RM-VBLE2-K9= 2461N-825321596 This Device Meets FCC and International Guidelines for Exposure to Radio Waves Cisco Beacon Point Module includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) recommended by international guidelines. The guidelines were developed by an independent scientific organization (ICNIRP) and include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. Table 10: Separation Distance MPE Distance Limit 0.0005 mW/cm² 30 cm (11.81 inches) 1.00 mW/cm² Cisco Beacon Hardware Installation Guide 15 Declarations of Conformity and Regulatory Information This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves REVIEW DRAFT - CISCO CONFIDENTIAL The World Health Organization has stated that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure then you can easily do so by reorienting antennas away from the user or placing he antennas at a greater separation distance then recommended. This Device Meets the Industry Canada Guidelines for Exposure to Radio Waves The Cisco Beacon Point Module includes a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves (radio frequency electromagnetic fields) as referenced in Health Canada Safety Code 6. The guidelines include a substantial safety margin designed into the limit to ensure the safety of all persons, regardless of age and health. As such the systems are designed to be operated as to avoid contact with the antennas by the end user. It is recommended to set the system in a location where the antennas can remain at least a minimum distance as specified from the user in accordance to the regulatory guidelines which are designed to reduce the overall exposure of the user or operator. Table 11: Separation Distance Frequency MPE Distance Limit 2.4 GHz 0.005 W/m² 30 cm (11.81 inches) 5.4 W/m² Health Canada states that present scientific information does not indicate the need for any special precautions for the use of wireless devices. They recommend that if you are interested in further reducing your exposure you can easily do so by reorienting antennas away from the user, placing the antennas at a greater separation distance than recommended, or lowering the transmitter power output. Cet appareil est conforme aux directives internationales en matière d'exposition aux fréquences radioélectriques Cet appareil de la gamme Cisco Beacon Point Module comprend un émetteur-récepteur radio. Il a été conçu de manière à respecter les limites en matière d'exposition aux fréquences radioélectriques (champs électromagnétiques de fréquence radio), recommandées dans le code de sécurité 6 de Santé Canada. Ces directives intègrent une marge de sécurité importante destinée à assurer la sécurité de tous, indépendamment de l'âge et de la santé. Par conséquent, les systèmes sont conçus pour être exploités en évitant que l'utilisateur n'entre en contact avec les antennes. Il est recommandé de poser le système là où les antennes sont à une distance minimale telle que précisée par l'utilisateur conformément aux directives réglementaires qui sont conçues pour réduire l'exposition générale de l'utilisateur ou de l'opérateur. Cisco Beacon Hardware Installation Guide 16 Declarations of Conformity and Regulatory Information Additional Information on RF Exposure REVIEW DRAFT - CISCO CONFIDENTIAL Table 12: Distance d'éloignement Fréquence MPE Distance Limite 2.4 GHz 0.005 W/m² 30 cm (11.81 inches) 5.4 W/m² Santé Canada affirme que la littérature scientifique actuelle n'indique pas qu'il faille prendre des précautions particulières lors de l'utilisation d'un appareil sans fil. Si vous voulez réduire votre exposition encore davantage, selon l'agence, vous pouvez facilement le faire en réorientant les antennes afin qu'elles soient dirigées à l'écart de l'utilisateur, en les plaçant à une distance d'éloignement supérieure à celle recommandée ou en réduisant la puissance de sortie de l'émetteur. Additional Information on RF Exposure You can find additional information on the subject at the following links: • Cisco Systems Spread Spectrum Radios and RF Safety white paper at this location. • FCC Bulletin 56: Questions and Answers about Biological Effects and Potential Hazards of Radio Frequency Electromagnetic Fields. • FCC Bulletin 65: Evaluating Compliance with the FCC guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. • You can obtain additional information from the following organizations. • World Health Organization Internal Commission on Non-Ionizing Radiation Protection at this location. • United Kingdom, National Radiological Protection Board at this location. • Cellular Telecommunications Association at this location. • The Mobile Manufacturers Forum at this location. Declaration of Conformity Statements All the Declaration of Conformity statements related to this product can be found at the following location: http://www.ciscofax.com Cisco Beacon Hardware Installation Guide 17 Declarations of Conformity and Regulatory Information Declaration of Conformity Statements REVIEW DRAFT - CISCO CONFIDENTIAL Cisco Beacon Hardware Installation Guide 18
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Unknown Create Date : 2017:10:06 04:18:36Z Modify Date : 2017:10:20 09:59:49-07:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : Unknown Title : Untitled Creator Tool : Unknown Metadata Date : 2017:10:20 09:59:49-07:00 Producer : XEP 4.9 build 20070312 Trapped : False Document ID : uuid:b1899607-9b5a-4fb3-89c6-cfd7e25358a4 Instance ID : uuid:fca66916-1ffa-4f79-8b8b-3478cdfff848 Page Mode : UseOutlines Page Count : 24EXIF Metadata provided by EXIF.tools