Cisco Systems ASA-AP702 ASA 5506-X WiFi Internal Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2503314
Application ID	0P+HJTEeg7Dn0qLioG4b/A==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.63kB (95426 bits)
Date Submitted	2015-01-16 00:00:00
Date Available	2015-07-15 00:00:00
Creation Date	2014-12-09 18:27:03
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2014-12-09 19:32:12
Document Title	Microsoft Word - Kenton_AP_ETRD_for_WNC_Feedback_09-10-2013-ok.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ChristyFan

Kenton WLAN module
User Guide
Model name: ASA5506-AP702
1 Purpose
The purpose of this document is to give an overall description of the hardware requirements of
the WLAN module used in Kenton project.
1.1 Scope
This document contains the requirements for the subject system and its top-level or architectural
design for an ODM partner. This document should only contain information needed to design
the system, since this document will go to multiple ODM vendors during the RFQ process.
The requirements specify the behavior of the system, both hardware and software. They do not
specify "how" the system will be built except for necessary constraints on the design such as
needed interfaces to other systems or valid constraints on size, shape, processor and memory
utilization, power consumption, etc. The behavior may be described in terms of how the system
enables the end user to perform work (i.e., the functions, performance, quality requirements, etc).
The architectural design describes the components of the system, their individual functions and
performance, and how they interface with each other.
Development considerations such as schedule, cost, development process, and staffing are not
included in this specification.
2 Functional Overview
2.1 System Overview
The Kenton WLAN module is designed f to be a pluggable module assembly to the wireless
version of Kenton Desktop Security Appliance. It will provide the following functionalities:
2x2 100mW
Dual Radios,
802.11n
Internal Antennas
Compliance to standards based Dual Radio, 2x2, 802.11n
 Dual Radio, 2x2, 100mW, Internal Antenna
Shall support Dual Concurrent Radios
 Dual Radio, 2x2, 100mW, Internal Antenna
Shall support limited lifetime warranty
Operating Temp: 0ºC to 40ºC
Storage Temp: -30ºC to 70ºC
Operating Humidity: 10% to 90% Non-condensing
Storage Humidity: 5% to 95% Non-condensing
The PCB must include a printed “Manufactured for Cisco” marking
(using the Cisco Logo as shown in EDCS-775872. The minimum width
of the Cisco logo is ½”. The location is preferable on the top of the PCB,
but the back is acceptable if spacing doesn’t allow it to be on the top. It
cannot be underneath a soldered component (but can be underneath a
mini-PCI card if one exists).
FCC Statement:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.
This device and its antenna(s) must not be co-located with any other transmitters except in
accordance with FCC multi-transmitter product procedures.
Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated
simultaneously without C2P.
This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in
indoor environment only.
Devices will not permit operations on channels 120-132 for 11a and 11n/a which overlap
the 5600 - 5650 MHz band.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is responsible for the
compliance to all the rules that apply to the product into which this certified RF module is
integrated.
Additional testing and certification may be necessary when multiple modules are used.
20cm minimum distance has to be able to be maintained between the antenna and the
users for the host this module is integrated into. Under such configuration, the FCC
radiation exposure limits set forth for an population/uncontrolled environment can be
satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least
20cm separation with the antenna while this end product is installed and operated. The
end user has to be informed that the FCC radio-frequency exposure guidelines for an
uncontrolled environment can be satisfied. The end user has to also be informed that
any changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate this equipment. If the size of the end product is smaller than
8x10cm, then additional FCC part 15.19 statement is required to be available in the
users manual: This device complies with Part 15 of FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX
FCC ID: LDKASA-AP702". If the size of the end product is larger than 8x10cm, then the
following FCC part 15.19 statement has to also be available on the label: This device
complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IC Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.
Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être
exploités. Sélection d'autres canaux n'est pas possible.
This device and its antenna(s) must not be co-located with any other transmitters except in
accordance with IC multi-transmitter product procedures.
Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated
simultaneously without reassessment permissive change.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en association avec une
autre antenne ou transmetteur.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350
MHz,
5470-5600 MHz and 5650-5725 MHz
Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350
MHz, 5470-5600 MHz et 5650-5725 MHz
The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for
harmful interference to co-channel mobile satellite systems.
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites
mobiles utilisant les mêmes canaux.
The maximum antenna gain permitted (for devices in the bands 5250-5350 MHz and
5470-5725 MHz) to comply with the e.i.r.p. limit.
le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et
5470-5725 MHz doit se conformer à la limite de p.i.r.e.;
Users should also be advised that high-power radars are allocated as primary users (i.e.
priority
users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could
cause interference and/or damage to LE-LAN devices.
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont
désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et
5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs
LAN-EL.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de
distance entre la source de rayonnement et votre corps.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for
the IC compliance requirement of the end product, which integrates this module.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least
20cm separation with the antenna while this end product is installed and operated. The
end user has to be informed that the IC radio-frequency exposure guidelines for an
uncontrolled environment can be satisfied. The end user has to also be informed that
any changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate this equipment. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX
IC : 2461B-ASAAP702 ".
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec
une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut
choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne
dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
This radio transmitter (ASA5506-AP702) has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain and
required antenna impedance for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that type,
are strictly prohibited for use with this device.
Le présent émetteur radio (ASA5506-AP702) a été approuvé par Industrie Canada pour fonctionner avec
les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour
chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au
gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Antenna list:
Band Ant.
Brand
Model Name
Antenna Type
Connector
Gain (dBi)
WNC
EAAH-N32
PIFA Antenna
I-PEX
2.97
WNC
EAAH-N32
PIFA Antenna
I-PEX
2.97
WNC
EAAH-N32
PIFA Antenna
I-PEX
3.89
WNC
EAAH-N32
PIFA Antenna
Note: Beamforming Gain=10*Log(2)=3.01dBi
I-PEX
3.89
2.4G
5G
Telec Statement:
5GHz product for indoor use only.
CE Statement:
This equipment complies with EU radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : ChristyFan
Create Date                     : 2014:12:09 18:27:03+08:00
Modify Date                     : 2014:12:09 19:32:12+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : ChristyFan
Title                           : Microsoft Word - Kenton_AP_ETRD_for_WNC_Feedback_09-10-2013-ok.doc
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2014:12:09 19:32:12+08:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:c38e0a45-977a-449c-876b-9c2576b5a478
Instance ID                     : uuid:ddaf326e-56db-4643-87d0-2708051c5d43
Page Count                      : 9

EXIF Metadata provided by EXIF.tools