Cisco Systems 15454M6Dc Users Manual

2015-01-05

• Contents
• About This Manual
  • Audience
  • Organization
  • Related Documentation
  • Conventions
  • Obtaining Documentation
    • World Wide Web
    • Optical Networking Product Documentation CD-ROM
    • Ordering Documentation
    • Documentation Feedback
  • Obtaining Technical Assistance
    • Cisco.com
    • Technical Assistance Center
      • Contacting TAC by Using the Cisco TAC Website
      • Contacting TAC by Telephone
• Hardware Installation
  • 1.1 Installation Overview
  • 1.2 Installation Equipment
    • 1.2.1 Included Materials
    • 1.2.2 User-Supplied Materials
      • 1.2.2.1 Tools Needed
      • 1.2.2.2 Test Equipment
  • 1.3 Rack Installation
    • 1.3.1 Reversible Mounting Bracket
      • Procedure: Reverse the Mounting Bracket to Fit a 19-Inch Rack
    • 1.3.2 Mounting a Single Node
      • Procedure: Mount the Shelf Assembly in a Rack (One Person)
      • Procedure: Mount the Shelf Assembly in a Rack (Two People)
    • 1.3.3 Mounting Multiple Nodes
      • Procedure: Mount Multiple Shelf Assemblies in a Rack
      • 1.3.3.1 Four Node Configuration
      • 1.3.3.2 ONS 15454 Bay Assembly
  • 1.4 Front Door Access
    • Procedure: Open the Front Cabinet Compartment (Door)
    • Procedure: Remove the Front Door
  • 1.5 Backplane Access
    • Procedure: Remove the Backplane Sheet Metal Covers
    • 1.5.1 Lower Backplane Cover
      • Procedure: Remove the Lower Backplane Cover
    • 1.5.2 Alarm Interface Panel
  • 1.6 EIA Installation
    • 1.6.1 BNC EIA
    • 1.6.2 High-Density BNC EIA
    • 1.6.3 SMB EIA
    • 1.6.4 AMP Champ EIA
      • Procedure: Install a BNC, High-Density BNC, or SMB EIA
      • Procedure: Install the AMP Champ EIA
  • 1.7 Fan-Tray Assembly Installation
    • Procedure: Install the Bottom Brackets and Air Filter
    • Procedure: Install the Fan-Tray Assembly
  • 1.8 Power and Ground Installation
    • Procedure: Install Redundant Power Feeds
  • 1.9 Alarm, Timing, LAN, and Craft Pin Connections
    • 1.9.1 Alarm Installation
      • Procedure: Install Alarm Wires on the Backplane
    • 1.9.2 Timing Installation
      • Procedure: Install Timing Wires on the Backplane
    • 1.9.3 LAN Installation
      • Procedure: Install LAN Wires on the Backplane
    • 1.9.4 TL1 Craft Interface Installation
      • Procedure: Install Craft Interface Wires on the Backplane
  • 1.10 Coaxial Cable Installation
    • 1.10.1 BNC Connector Installation
      • Procedure: Install Coaxial Cable With BNC Connectors
    • 1.10.2 High-Density BNC Connector Installation
      • Procedure: Install Coaxial Cable With High-Density BNC Connectors
    • 1.10.3 SMB Connector Installation
      • Procedure: Install Coaxial Cable with SMB Connectors
  • 1.11 DS-1 Cable Installation
    • 1.11.1 Twisted Pair Wire-Wrap Installation
      • Procedure: Install DS-1 Cables Using Electrical Interface Adapters (Balun)
    • 1.11.2 AMP Champ Connector Installation
      • Procedure: Install DS-1 AMP Champ Cables on the AMP Champ EIA
  • 1.12 Card Installation
    • 1.12.1 Slot Requirements
      • Procedure: Install the TCC+ and XC/XCVT/XC10G Cards
      • Procedure: Install Optical, Electrical, and Ethernet Cards
      • Procedure: Install the AIC Card
    • 1.12.2 Gigabit Interface Converter
      • Procedure: Install Gigabit Interface Converters
      • Procedure: Remove a Gigabit Interface Converter
  • 1.13 Fiber-Optic Cable Installation
    • Procedure: Install Fiber-Optic Cables on OC-N Cards
    • Procedure: Install the Fiber Boot
  • 1.14 Cable Routing and Management
    • 1.14.1 Optical Cable Management
      • Procedure: Route Fiber-Optic Cables in the Shelf Assembly
    • 1.14.2 Coaxial Cable Management
      • Procedure: Route the Coaxial Cables
    • 1.14.3 DS-1 Twisted-Pair Cable Management
      • Procedure: Route DS-1 Twisted-Pair Cables
    • 1.14.4 AMP Champ Cable Management
    • 1.14.5 BIC Rear Cover Installation
      • Procedure: Install the BIC Rear Cover
  • 1.15 Ferrite Installation
    • Procedure: Attach Ferrites to Power Cabling
    • Procedure: Attach Ferrites to Wire-Wrap Pin Fields
  • 1.16 ONS 15454 Assembly Specifications
    • 1.16.1 Bandwidth
    • 1.16.2 Slot Assignments
    • 1.16.3 Cards
    • 1.16.4 Configurations
    • 1.16.5 Cisco Transport Controller
    • 1.16.6 External LAN Interface
    • 1.16.7 TL1 Craft Interface
    • 1.16.8 Modem Interface
    • 1.16.9 Alarm Interface
    • 1.16.10 EIA Interface
    • 1.16.11 Nonvolatile Memory
    • 1.16.12 BITS Interface
    • 1.16.13 System Timing
    • 1.16.14 Power Specifications
    • 1.16.15 Environmental Specifications
    • 1.16.16 Dimensions
  • 1.17 Installation Checklist
  • 1.18 ONS 15454 Software and Hardware Compatibility Matrix
• Software Installation
  • 2.1 Installation Overview
  • 2.2 Computer Requirements
  • 2.3 Running the CTC Setup Wizard
    • Procedure: Run the CTC Setup Wizard
    • Procedure: Set Up the Environment Variable (Solaris installations only)
    • Procedure: Reference the JRE (Solaris installations only)
  • 2.4 Connecting PCs to the ONS 15454
    • 2.4.1 Direct Connections to the ONS 15454
      • Procedure: Creating a Direct Connection to an ONS 15454
    • 2.4.2 Network Connections
      • Procedure: Access the ONS 15454 from a LAN
      • Procedure: Disable Proxy Service Using Internet Explorer (Windows)
      • Procedure: Disable Proxy Service Using Netscape (Windows and Solaris)
    • 2.4.3 Remote Access to the ONS 15454
    • 2.4.4 TL1 Terminal Access to the ONS 15454
  • 2.5 Logging into the ONS 15454
    • Procedure: Log into the ONS 15454
    • 2.5.1 Creating Login Node Groups
      • Procedure: Create a Login Node Group
    • 2.5.2 Accessing ONS 15454s Behind Firewalls
      • Procedure: Set the IIOP Listener Port on the ONS 15454
      • Procedure: Set the IIOP Listener Port on CTC
  • 2.6 Working with the CTC Window
    • 2.6.1 Node View
      • 2.6.1.1 CTC Card Colors
      • 2.6.1.2 Node View Card Shortcuts
      • 2.6.1.3 Node View Tabs
    • 2.6.2 Network View
      • 2.6.2.1 CTC Node Colors
      • 2.6.2.2 Network View Tasks
      • 2.6.2.3 Creating Domains
      • 2.6.2.4 Changing the Network View Background Color
      • Procedure: Modify the Network or Domain Background Color
      • 2.6.2.5 Changing the Network View Background Image
      • Procedure: Change the Network View Background Image
      • Procedure: Add a Node to the Current Session
    • 2.6.3 Card View
  • 2.7 CTC Navigation
  • 2.8 Viewing CTC Table Data
  • 2.9 Printing and Exporting CTC Data
    • Procedure: Print CTC Window and Table Data
    • Procedure: Export CTC Data
  • 2.10 Displaying CTC Data in Other Applications
• Node Setup
  • 3.1 Before You Begin
  • 3.2 Setting Up Basic Node Information
    • Procedure: Add the Node Name, Contact, Location, Date, and Time
  • 3.3 Setting Up Network Information
    • Procedure: Set Up Network Information
    • Procedure: Change IP Address, Default Router, and Network Mask Using the LCD
  • 3.4 Creating Users and Setting Security
    • Procedure: Create New Users
    • Procedure: Edit a User
    • Procedure: Delete a User
  • 3.5 Creating Protection Groups
    • Procedure: Create Protection Groups
    • Procedure: Enable Ports
    • Procedure: Edit Protection Groups
    • Procedure: Delete Protection Groups
  • 3.6 Setting Up ONS 15454 Timing
    • 3.6.1 Network Timing Example
    • 3.6.2 Synchronization Status Messaging
      • Procedure: Set up ONS 15454 Timing
      • Procedure: Set Up Internal Timing
  • 3.7 Viewing ONS 15454 Inventory
  • 3.8 Viewing CTC Software Versions
• IP Networking
  • 4.1 IP Networking Overview
  • 4.2 ONS 15454 IP Addressing Scenarios
    • 4.2.1 Scenario 1: CTC and ONS 15454s on Same Subnet
    • 4.2.2 Scenario 2: CTC and ONS 15454s Connected to Router
    • 4.2.3 Scenario 3: Using Proxy ARP to Enable an ONS 15454 Gateway
    • 4.2.4 Scenario 4: Default Gateway on CTC Computer
    • 4.2.5 Scenario 5: Using Static Routes to Connect to LANs
      • Procedure: Create a Static Route
    • 4.2.6 Scenario 6: Static Route for Multiple CTCs
    • 4.2.7 Scenario 7: Using OSPF
      • Procedure: Set up OSPF
  • 4.3 Viewing the ONS 15454 Routing Table
• SONET Topologies
  • 5.1 Before You Begin
  • 5.2 Bidirectional Line Switched Rings
    • 5.2.1 Two-Fiber BLSRs
    • 5.2.2 Four-Fiber BLSRs
    • 5.2.3 BLSR Bandwidth
    • 5.2.4 Sample BLSR Application
    • 5.2.5 Setting Up BLSRs
      • Procedure: Install the BLSR Trunk Cards
      • Procedure: Create the BLSR DCC Terminations
      • Procedure: Enable the BLSR Ports
      • Procedure: Provision the BLSR
    • 5.2.6 Upgrading From Two-Fiber to Four-Fiber BLSRs
      • Procedure: Upgrade From a Two-Fiber to a Four-Fiber BLSR
    • 5.2.7 Adding and Removing BLSR Nodes
      • Procedure: Add a BLSR Node
      • Procedure: Remove a BLSR Node
    • 5.2.8 Moving BLSR Trunk Cards
      • Procedure: Move a BLSR Trunk Card
  • 5.3 Unidirectional Path Switched Rings
    • 5.3.1 Example UPSR Application
    • 5.3.2 Setting Up a UPSR
      • Procedure: Install the UPSR Trunk Cards
      • Procedure: Configure the UPSR DCC Terminations
      • Procedure: Enable the UPSR Ports
    • 5.3.3 Adding and Removing UPSR Nodes
      • Procedure: Switch UPSR Traffic
      • Procedure: Add a UPSR Node
      • Procedure: Remove a UPSR Node
  • 5.4 Subtending Rings
    • Procedure: Subtend a UPSR from a BLSR
    • Procedure: Subtend a BLSR from a UPSR
    • Procedure: Subtend a BLSR from a BLSR
  • 5.5 Linear ADM Configurations
    • Procedure: Create a Linear ADM
    • Procedure: Convert a Linear ADM to UPSR
    • Procedure: Convert a Linear ADM to a BLSR
  • 5.6 Path-Protected Mesh Networks
• Circuits and Tunnels
  • 6.1 Circuits Overview
  • 6.2 Creating Circuits and VT Tunnels
    • Procedure: Create an Automatically Routed Circuit
    • Procedure: Create a Manually Routed Circuit
  • 6.3 Creating Multiple Drops for Unidirectional Circuits
    • Procedure: Create a Unidirectional Circuit with Multiple Drops
  • 6.4 Creating Monitor Circuits
    • Procedure: Create a Monitor Circuit
  • 6.5 Searching for Circuits
    • Procedure: Search for ONS 15454 Circuits
  • 6.6 Editing UPSR Circuits
    • Procedure: Edit a UPSR Circuit
  • 6.7 Creating a Path Trace
    • Procedure: Create a J1 Path Trace
  • 6.8 Cross-Connect Card Capacities
    • 6.8.1 VT1.5 Cross-Connects
    • 6.8.2 VT Tunnels
  • 6.9 Creating DCC Tunnels
    • Procedure: Provision a DCC Tunnel
• Card Provisioning
  • 7.1 Performance Monitoring Thresholds
  • 7.2 Provisioning Electrical Cards
    • 7.2.1 DS-1 Card Parameters
      • Procedure: Modify Line and Threshold Settings for the DS-1 Card
    • 7.2.2 DS-3 Card Parameters
      • Procedure: Modify Line and Threshold Settings for the DS-3 Card
    • 7.2.3 DS3E Card Parameters
      • Procedure: Modify Line and Threshold Settings for the DS3E Card
    • 7.2.4 DS3XM-6 Card Parameters
      • Procedure: Modify Line and Threshold Settings for the DS3XM-6 Card
    • 7.2.5 EC1-12 Card Parameters
      • Procedure: Modify Line and Threshold Settings for the EC-1 Card
  • 7.3 Provisioning Optical Cards
    • 7.3.1 Modifying Transmission Quality
      • Procedure: Provision Line Transmission Settings for OC-N Cards
      • Procedure: Provision Threshold Settings for OC-N Cards
    • 7.3.2 Provisioning OC-N Cards for SDH
      • Procedure: Provision an OC-N Card for SDH
  • 7.4 Provisioning IPPM
    • Procedure: Enable Intermediate-Path Performance Monitoring
  • 7.5 Provisioning the Alarm Interface Controller
    • 7.5.1 Using Virtual Wires
      • Procedure: Provision External Alarms
      • Procedure: Provision External Controls
    • 7.5.2 Provisioning AIC Orderwire
      • Procedure: Provision AIC Orderwire
    • 7.5.3 Using the AIC Orderwire
  • 7.6 Converting DS-1 and DS-3 Cards From 1:1 to 1:N Protection
    • Procedure: Convert DS1-14 Cards From 1:1 to 1:N Protection
    • Procedure: Convert DS3-12 Cards From 1:1 to 1:N Protection
• Performance Monitoring
  • 8.1 Using the Performance Monitoring Screen
    • 8.1.1 Viewing PMs
      • Procedure: View PMs
    • 8.1.2 Changing the Screen Intervals
      • Procedure: Select Fifteen-Minute PM Intervals on the Performance Monitoring Screen
      • Procedure: Select Twenty-Four Hour PM Intervals on the Performance Monitoring Screen
    • 8.1.3 Viewing Near End and Far End PMs
      • Procedure: Select Near End PMs on the Performance Monitoring Screen
      • Procedure: Select Far End PMs on the Performance Monitoring Screen
    • 8.1.4 Using the Signal-Type Menu
      • Procedure: Select Signal-Type Menus on the Performance Monitoring Screen
    • 8.1.5 Using the Baseline Button
      • Procedure: Use the Baseline Button on the Performance Monitoring Screen
    • 8.1.6 Using the Clear Button
      • Procedure: Use the Clear Button on the Performance Monitoring Screen
  • 8.2 Changing Thresholds
  • 8.3 Enabling Intermediate-Path Performance Monitoring
  • 8.4 Pointer Justification Count Parameters
    • Procedure: Enable Pointer Justification Count Performance Monitoring
  • 8.5 Performance Monitoring for Electrical Cards
    • 8.5.1 EC1 Card Performance Monitoring Parameters
    • 8.5.2 DS1 and DS1N Card Performance Monitoring Parameters
    • 8.5.3 DS3 and DS3N Card Performance Monitoring Parameters
    • 8.5.4 DS3-12E and DS3N-12E Card Performance Monitoring Parameters
    • 8.5.5 DS3XM-6 Card Performance Monitoring Parameters
  • 8.6 Performance Monitoring for Optical Cards
    • 8.6.1 OC-3 Card Performance Monitoring Parameters
    • 8.6.2 OC-12, OC-48, and OC-192 Card Performance Monitoring Parameters
• Ethernet Operation
  • 9.1 Ethernet Cards
    • 9.1.1 E100T-12/E100T-G
    • 9.1.2 E1000-2/E1000-2-G
    • 9.1.3 Port Provisioning for Ethernet Cards
      • Procedure: Provision Ethernet Ports
  • 9.2 Multicard and Single-Card EtherSwitch
    • 9.2.1 Multicard EtherSwitch
    • 9.2.2 Single-Card EtherSwitch
    • 9.2.3 ONS 15454 and ONS 15327 EtherSwitch Circuit Combinations
  • 9.3 Ethernet Circuit Configurations
    • 9.3.1 Point-to-Point Ethernet Circuits
      • Procedure: Provision an EtherSwitch Point-to-Point Circuit (Multicard or Single-Card)
    • 9.3.2 Shared Packet Ring Ethernet Circuits
      • Procedure: Provision a Shared Packet Ring
    • 9.3.3 Hub and Spoke Ethernet Circuit Provisioning
      • Procedure: Provision a Hub and Spoke Ethernet Circuit
    • 9.3.4 Ethernet Manual Cross-Connects
      • Procedure: Provision a Single-card EtherSwitch Manual Cross-Connect
      • Procedure: Provision a Multicard EtherSwitch Manual Cross-Connect
  • 9.4 VLAN Support
    • 9.4.1 Q-Tagging (IEEE 802.1Q)
    • 9.4.2 Priority Queuing (IEEE 802.1Q)
    • 9.4.3 VLAN Membership
      • Procedure: Provision Ethernet Ports for VLAN Membership
  • 9.5 Spanning Tree (IEEE 802.1D)
    • 9.5.1 Multi-Instance Spanning Tree and VLANs
      • Procedure: Enable Spanning Tree on Ethernet Ports
    • 9.5.2 Spanning Tree Parameters
    • 9.5.3 Spanning Tree Configuration
    • 9.5.4 Spanning Tree Map
      • Procedure: View the Spanning Tree Map
  • 9.6 Ethernet Performance and Maintenance Screens
    • 9.6.1 Statistics Screen
    • 9.6.2 Line Utilization Screen
    • 9.6.3 History Screen
    • 9.6.4 MAC Table Screen
      • Procedure: Retrieve the MAC Table Information
    • 9.6.5 Trunk Utilization Screen
  • 9.7 Remote Monitoring Specification Alarm Thresholds
    • Procedure: Creating Ethernet RMON Alarm Thresholds
• Alarm Monitoring and Management
  • 10.1 Overview
  • 10.2 Viewing ONS 15454 Alarms
    • 10.2.1 Controlling Alarm Display
    • 10.2.2 Viewing Alarm-Affected Circuits
      • Procedure: View Affected Circuits for a Specific Alarm
    • 10.2.3 Conditions Tab
      • 10.2.3.1 Retrieve and Display Conditions
      • 10.2.3.2 Conditions Column Descriptions
    • 10.2.4 Viewing History
    • 10.2.5 Viewing Alarms on the LCD
      • Procedure: View Alarm Counts on a Specific Slot and Port
  • 10.3 Alarm Profiles
    • 10.3.1 Creating and Modifying Alarm Profiles
      • Procedure: Create an Alarm Profile
      • 10.3.1.1 Alarm Profile Menus
      • 10.3.1.2 Alarm Profile Editing
      • 10.3.1.3 Alarm Severity Option
      • 10.3.1.4 Row Display Options
    • 10.3.2 Applying Alarm Profiles
      • Procedure: Apply an Alarm Profile at the Card View
      • Procedure: Apply an Alarm Profile at the Node View
  • 10.4 Suppressing Alarms
    • Procedure: Suppressing Alarms
• SNMP
  • 11.1 SNMP Overview
  • 11.2 SNMP Basic Components
  • 11.3 SNMP Support
    • Procedure: Set Up SNMP Support
  • 11.4 SNMP Management Information Bases
  • 11.5 SNMP Traps
  • 11.6 SNMP Community Names
  • 11.7 SNMP Remote Network Monitoring
    • 11.7.1 Ethernet Statistics Group
    • 11.7.2 History Control Group
    • 11.7.3 Ethernet History Group
    • 11.7.4 Alarm Group
    • 11.7.5 Event Group
• Circuit Routing
  • Automatic Circuit Routing
    • Circuit Routing Characteristics
    • Bandwidth Allocation and Routing
    • Secondary Sources and Drops
  • Manual Circuit Routing
  • Constraint-Based Circuit Routing
• Regulatory and Compliance Requirements
  • Regulatory Compliance
  • Japan Approvals
    • Label Information
    • Class A Notice
  • Installation Warnings
    • DC Power Disconnection Warning
    • DC Power Connection Warning
    • Power Supply Disconnection Warning
    • Outside Line Connection Warning
    • Class 1 Laser Product Warning
    • Class I and Class 1M Laser Warning
    • Restricted Area Warning
    • Ground Connection Warning
    • Qualified Personnel Warning
    • Invisible Laser Radiation Warning (other versions available)
    • More Than One Power Supply
    • Unterminated Fiber Warning
    • Laser Activation Warning
• Acronyms
• Glossary
• index