Cisco Systems IR510OFDM Cisco IR510 WPAN Industrial Router User Manual

Cisco Systems Inc Cisco IR510 WPAN Industrial Router

User Manual

1Cisco Systems, Inc. www.cisco.comDraft version 3.0 — Cisco ConfidentialIR510 and IR530 Hardware-Cisco IOSLast Updated: 2018-03-07<internally>First Published: 2018-02-08 <internally>OrganizationThis guide includes the following sections:ConventionsThis document uses the following conventions. Conventions, page 1 Details on style conventions used in the guide.Overview, page 2 Provides hardware and software specifications on IR510 and IR530.Installation Guidelines, page 8 Provides a summary of warnings to note before you install the IR510 and IR530.Configuring IR510 and IR530 Systems, page 8 Provides hardware and software specifications on the Cisco IR510 and IR530 Series Resilient Mesh Range Extender and supported antennas; and, configuration details using IoT FND 4.2.x and Cisco command line interface (CLI).Conventions Indicationbold font Commands and keywords and user-entered text appear in bold font.italic font Document titles, new or emphasized terms, and arguments for which you supply values are in italic font.[ ] Elements in square brackets are optional.
2IR510 and IR530 Hardware-Cisco IOSDraft version 3.0 — Cisco ConfidentialOverviewNote: Means reader take note. Notes contain helpful suggestions or references to material not covered in the manual.Caution: Means reader be careful. In this situation, you might perform an action that could result in equipment damage or loss of data.Warning: IMPORTANT SAFETY INSTRUCTIONSMeans danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.Caution: Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), article 800, Grounding of Outer Conductive Shield of a Coaxial Cable. WARNING : Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030SAVE THESE INSTRUCTIONSRegulatory: Provided for additional information and to comply with regulatory and customer requirements. OverviewThis chapter describes the Cisco Industrial Router 510 (IR510) WPAN Distribution Automation (DA) Gateway and includes the following topics:IR 510 Hardware Overview, page 2IR530 Hardware Overview, page 5IR 510 Hardware OverviewThe IR510 WPAN Distribution Automation (DA) Gateway operates within a wireless mesh network, providing intelligent control over endpoint devices that use Serial (RS232/RS485), USB (LS/FS/HS), or Fast Ethernet (10/100 Fast Ethernet) ports. Additionally, the gateway employs GPS for time synchronization and location tracking.The IR510 DA Gateway works with the CGR1000 series of routers, primarily in the electrical grid to provide a low cost, low power, small size DA solution. The IR510 DA Gateway (Figure 1 IR510 in IP30 Enclosure, page 3) comes within a ruggedized IP30 enclosure. The enclosure allows installation of IR510 within outdoor cabinets.{x | y | z } Required alternative keywords are grouped in braces and separated by vertical bars.[ x | y | z ] Optional alternative keywords are grouped in brackets and separated by vertical bars.string A nonquoted set of characters. Do not use quotation marks around the string or the string will include the quotation marks.courier font Terminal sessions and information the system displays appear in courier font.< > Nonprinting characters such as passwords are in angle brackets.[ ] Default responses to system prompts are in square brackets.!, # An exclamation point (!) or a pound sign (#) at the beginning of a line of code indicates a comment line.Conventions Indication
3 Draft version 3.0 — Cisco ConfidentialIR510 and IR530 Hardware-Cisco IOSOverviewFigure 1 IR510 in IP30 EnclosureIR510 System SpecificationsTable 1 IR510 Hardware SpecificationsItem Description Dimensions 5.9 x 5 x 1.75 (Inches)Operating ambient temperature range -40C to +60 (Celsius)DC Power Supply Supports 12-48Vdc nominal, 9.6-60Vdc maximum rangeReset button Allows factory reset when you press button for approximately 5 seconds.
4IR510 and IR530 Hardware-Cisco IOSDraft version 3.0 — Cisco ConfidentialOverviewTable 2 IR510 Device InterfacesItem DescriptionAlarm port Port has one Isolated input for open and closed relay detection.QMA Antenna Port 900 MHz ISM band, Omni stick, 24 inch, 5 dBi, N(f), Cisco PID ANT-WPAN-OM-OUT-N.Panel-mounted, 50-ohm connector for connecting the antenna to the WPAN gateway.Supports the IR509 antenna (ANT-WPAN-OM-OUT-N)RJ45 Fast Ethernet 10/100 port Provides 10/100 Mb/s device connections.RJ45 RS232-DCE or RS485 port Provides user the option to configure either port interface via software on the same RJ45 port.RS232 operates in full duplex mode portRS485 operates in half duplex or full duplex mode.Use the IoT Field Network Director (FND) 4.1 (and higher) User Guide to configure the port and provide statistics about the serial port including bytes sent and received information.RS232 Console port To access the console port, remove the front cover.RS232-DTE port Provides for direct connection to a DCE port. Use theIoT Field Network Director (FND) 4.1 (and higher) User Guide to configure the port and get statistics about the port including bytes sent and bytes received information.USB-A (LS/FS/HS) Host port Supports the following signaling rates: 1Mb/s (low speed), 12Mb/s (full speed) and 480 Mb/s (high speed).Table 3 IR510 LEDsLED Green Yellow RedPWR (Power) OK: All Power OK: 12K PSU only ---SYS (System) Blinking: Master Controller Unit (MCU) is running system softwareBlinking: MCU is booting up ---CPU (System) Blinking: CPU is actively running user application Blinking: CPU is booting up ---ALM --- --- Solid: Alarm DetectedFE Solid: Ethernet Link EstablishedBlinking: Ethernet Activity Detected--- ---RS232-DCE Solid: S0 Port is RS232 DCE --- ---RS485 Solid: S0 Port is RS485 --- ---RS232-DTE Solid: S1 Port is RS232 DTE --- ---
5 Draft version 3.0 — Cisco ConfidentialIR510 and IR530 Hardware-Cisco IOSOverviewIR530 Hardware OverviewFor details on Environmental Compliance, Immunity, EMC, Safety and Ingress Protection (dust/water) or to confirm any IR530 Hardware Specifications, please refer to the Cisco IR530 Series Resilient Mesh Range Extenders Data Sheet.For details on Environmental Compliance, Immunity, EMC, Safety and Ingress Protection (dust/water) or to confirm any IR530 Hardware Specifications, please refer to the Cisco IR530 Series Resilient Mesh Range Extenders Data Sheet.Table 4 IR510 Product IDs and AccessoriesProduct ID DescriptionIR510-OFDM-FCC/K9 Cisco 510 WPAN Industrial RouterIR510-DINRAIL= DIN Rail spare assemblyANT-UN-MP-OUT-QMA Antenna with QMA connector and 5 ft cable for use with IR510ANT-UN-MP-OUT-QMA= Antenna with QMA connector and 5 ft cable for use with IR510 (Spare)ANT-WPAN-OM-OUT-N Omni antenna for 900 MHz WPAN (Outdoor)Table 5 IR530 Hardware SpecificationsItem Description Dimensions (W x D x H) 5.2” x 7.23” x 10.37”Typical weight fully configured 8.4 lbs (3.8 kg)Pole mount YesOperating temperature 40°C to +70°C (-40°F to 158°F) with IEEE 1613 type test up to 85°C (185°F) for 16 hoursTypical power consumption or dissipation Normal operation: 6W max with BBU charging: 23W maxIEEE 802.15.4 WPAN IEEE 802.15.4g/e/vFrequency supportSpread spectrum technology OFDM Option 2 802.15.4gFrequency hopping between up to quantity 31 800 kHz channelsPHY data rates of 50 kb/s, 200 kbps, 800 kbps, and 1200kbpsTransmitter output (conducted) 28 dBm typical, at 50 kb/s, and 200 kbps25 dBm typical, at 800 kb/s,24 dBm typical, at 1200 kb/s,Antenna connector RF Mesh QMA N connector (female)RS 232 serial console port 1Digital alarm inputs 1Integrated AC/DC power supply input range 85 – 264 VAC, 47 – 63 HzPower Consumption 6W (no BBU charging) 20W (BBU charging)
6IR510 and IR530 Hardware-Cisco IOSDraft version 3.0 — Cisco ConfidentialOverview
7 Draft version 3.0 — Cisco ConfidentialIR510 and IR530 Hardware-Cisco IOSOverviewTable 6 LEDs for IR530Table 7 IR530 AntennasFor more details on the supported antenna, please refer to the document below:Connected Grid Antennas Installation GuideCable OptionsRefer to the Cisco IR530 Series Resilient Mesh Range Extenders Data Sheet for a summary of all supported cables, see Table 4.LED Name Definition StateRSSI Measure of power present in the received radio signal.Yellow (Off) / Green (Off): RSSI less than -105 dBmYellow (On) / Green (Off): RSSI is -105 to -95 dBmYellow (Off) / Green (Slow Blink): RSSI is -95 to -75 dBmYellow (Off) / Green (Fast Blink): RSSI is -75 to -60 dBmYellow (Off) / Green (Solid On): RSSI greater than -60 dBmWPAN WPAN traffic activity detect. Yellow (Off) / Green (Off): WPAN port is disabled.Yellow (On) / Green (Off): Searching for network.Yellow (Off) / Green (Slow Blink): WPAN port is up.Yellow (Off) / Green (Fast Blink): Route is available and DHCPv6 configuration is starting.Yellow (Off) / Green (On): Global IPv6 address is available.SYS Indicates module status. Green (Blinking): Broadcast slot time completeYellow (Blinking): Bootload in processYellow (Solid): Software update mode in processCisco Part Number Description ANT-WPAN-OM-OUT-N Omni antenna for 900 MHz WPAN, outdoor
8IR510 and IR530 Hardware-Cisco IOSDraft version 3.0 — Cisco ConfidentialInstallation GuidelinesIR530 WPAN RF900 Range Extender (RE) Product IDsInstallation GuidelinesCAUTION : Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not stack routers on a desktop. Excessive weight on top of the router could damage the chassis.CAUTION : Do not install the router or power supplies next to a heat source of any kind, including heating vents.WARNING : In order to comply with FCC radio frequency (RF) exposure limits, antennas for this product should be located a minimum of 7.9 in (20cm) or more from the body of all persons. Statement 332WARNING : Read the installation instructions before connecting the system to the power source. Statement 1004WARNING : Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030WARNING : No user-serviceable parts inside. Do not open. Statement 1073WARNING : Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040WARNING : Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death. For proper installation and grounding of the antenna, please refer to national and local codes (for example, U.S.:NFPA 70, National Electrical Code, Article 810, Canada: Canadian Electrical Code, Section 54). Statement 1052WARNING : This product is not intended to be directly connected to the Cable Distribution System. Additional regulatory compliance and legal requirements may apply for direct connection to the Cable Distribution System. This product may connect to the Cable Distribution System ONLY through a device that is approved for direct connection. Statement 1078Configuring IR510 and IR530 SystemsIoT Field Network Director (IoT-FND) 4.2.x release provides the user interface for IR510 and IR530 configuration as well as the configuration and management and the CGM-WPAN-OFDM Module.IoT-FND Configuration NotesThe following guides provide information on installing and configuring the Cisco IR510 and IR530 systems:Cisco IoT Field Network Director Installation Guide, Release 4.2.xCisco IoT Field Network Director User Guide, Release 4.2.xTable 8 IR530 Product IDs and AccessoriesProduct ID DescriptionR530-OFDM-FCC/K9 IR530 with 915MHz-WPAN, utility-grade DC power. For all North and South America except Brazil.IR530-OFDM-BRZ/K9 IR530 with 915MHz-WPAN, utility-grade DC power. For Brazil.IR530-OFDM-ANZ/K9 IR530 with 915MHz-WPAN, utility-grade DC power. For Australia and New Zealand.
9 Draft version 3.0 — Cisco ConfidentialIR510 and IR530 Hardware-Cisco IOSConfiguring IR510 and IR530 SystemsCLI Configuration NotesTable 9 Summary of New CLI Interface commands for the IR510 and IR530Command Definitionieee154 phy-mode <64|96|66|98|144|146|147|149| 150|192>Defines the IEEE154 phy-mode. Possible options noted below, default value is 149.
10IR510 and IR530 Hardware-Cisco IOSDraft version 3.0 — Cisco ConfidentialConfiguring IR510 and IR530 Systems

Navigation menu