Cixi City Yidong Electronic RC2U RC-2U User Manual RC 2U RCS 7U20151222

Cixi City Yidong Electronic Co., Ltd. RC-2U RC 2U RCS 7U20151222

Contents

user manual RC-2U with RCS-7U_REV1

RC-2U+RCS-7U Operation Instruction A. Function 1. Random/Learning code. 2. Operation code is 24 bit address code and CRC check,repeat probability is 1 / 16,777,216. 3. Receiver has a built-in memory,it can remember the data for 10 years. 4. Remote control works up to 80 feet. B. Diagram C. Operation 1. Pull out insulating strip from battery cover of transmitter. Then press ON/OFF key to check whether it can work. If LED indicator of transmitter turns on, it means this Transmitter works well. 2. Put Receiver into outlet, LED indicator of Receiver flashes. Enter into leaning mode. Notes: Receiver will exit leaning mode after 29 seconds without any operation. Then please pull out Receiver and operate again. 3. Press Transmitter’s ON/OFF key once to connect with Receiver. 4. Then you can use it normally by pressing Transmitter’s ON/OFF key. LED indicator turns on, it means power is on. In contrast, power is off. D. Specification 1. Battery:1 pc CR2032.3V 2. Radio Frequency: 433.92MHz 3. Receiver category:Class 3 4. Power supply:125VAC,60Hz. Max.load: 125VAC,60Hz 8A Resistive or General purpose; 600W(4.8A) Tungsten .
Caution: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Navigation menu