Cixi City Yidong Electronic RC5U RC-5U User Manual RLCT 3U RC 5U 20170705
Cixi City Yidong Electronic Co., Ltd. RC-5U RLCT 3U RC 5U 20170705
User manual_RC 5U
The Manual of Light Sensor Timer with Remote Control
Please read the following instructions carefully before connecting this timer to electrical
appliances.
Specification
Model No.: RLCT-3U+RC-5U
Battery:
12V, 23A
Radio Frequency: 433.92MHz
Transmitter duty cycle<10%
Receiver category:Class 3
Power supply:125VAC,60Hz.
Max.load: 15A Resistive or General purpose; 1250W 10A Tungsten, TV-5, 1/2HP .
Feature:
Remote Control
- Random/Learning code.
- Operation code is 24 bit address code and CRC check.
- Remote control works up to 80 feet in the open area.
Timer Dial: OFF, ON, Dusk-Dawn, 2Hrs, 4Hrs, 6Hrs, 8Hrs, repeat daily.
Power Light: Indicates if timer is turned on or off
Light Sensor: Turns timer on at dusk and off at dawn
Operation
1. Remote control
- Put Receiver into outlet, LED indicator of Receiver flashes (Enter into learning mode).
Notes: Receiver will exit leaning mode after 29 seconds without any operation. Then please
pull out Receiver and operate again.
- Press Transmitter’s ON key once to connect with Receiver.
- Then you can use it normally by pressing Transmitter’s ON/OFF key. LED indicator turns on,
it means power is on. In contrast, power is off
2. Timer dial function
Simply twist the timer dial:
- OFF Position: Timer is always OFF.
- ON Position: Timer is always ON.
- DUSK-DAWN Position: Turn timer on at dusk and off at dawn, repeat daily.
- 2, 4, 6 or 8Hrs Position: Turn timer on at dusk for 2, 4, 6 or 8 hours, then off, repeat daily.
PLEASE NOTE:
- After dusk, a temporary light source (like headlights, flashlight and other external lights) will
not interfere with the active timer program. BUT, if timer (in DUSK-DAWN program) receives
a temporary light source with continuous 8 seconds or above, timer will turn off until darkness
is restored. If timer (in 2, 4, 6 or 8H program) receives a temporary light source with continuous
8 seconds or above, timer will turn off. When this temporary light source is gone, timer will
turn on and restart 2, 4, 6 or 8 hours count down.
-
Once using remote control function, light sensor timer function is invalid. Twist timer dial
manually to reactivate light sensor timer function.
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de
brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.