Classic Tech Development HP1292-001R Wireless Headphone Receiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	416202
Application ID	D7MZmJSMbRiXJus8IKT2JQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.42kB (80191 bits)
Date Submitted	2004-04-21 00:00:00
Date Available	2004-04-20 00:00:00
Creation Date	2004-04-14 23:05:58
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2004-04-14 23:05:59
Document Title	Users Manual

HP1290
(HP1291 + HP1292S)
Cordless Stereo 900Mhz
Headphone System
User's Manual
(draft)
INTRODUCTION
This 900Mhz compact stereo headphone takes advantage of the very latest
advances in wireless transmission technology and unique SRS surround effect
so that you can listen to music or the sound from your TV set both in the house
and outdoors. All you have to do is connect the transmitter to any audio source:
DVD player, CD player, TV set, VCR, Hi-Fi system or radio (range 100 meters).
FEATURES
1.
SRS Surround Effect
2.
Automatic Phases Lock Loop (PLL) scanning system on headphone
3.
Phase Lock Loop (PLL) transmission system on transmitter
4.
Automatic battery recharging (batteries supplied).
5.
900 MHz RF technology.
6.
RF technology leaves you completely free to move around.
7.
Transmission is not restricted solely to line of sight.
8.
Rechargeable receiver headphones.
9.
Charger built into the transmitter.
10.
High quality stereo sound that is virtually interference-free.
11. Automatic Level Control (ALC) and Auto On/Off function.
INSTALLATION
TRANSMITTER
1.
Connect the mains adapter provided to an electrical outlet.
2.
Connect the mains adapter cable to the DC IN input connector located on
the transmitter rear panel.
3.
A cable is provided from the transmitter rear panel that can be connected to
the audio outputs (Left and Right) present on a TV set, Hi-Fi system, VCR or
radio-cassette player, or to a headphones/earphones output using the
connector supplied.
The red Auto On indicator light will light up as soon as you have connected the
power adapter to the mains outlet and the audio cable to a signal source. If the
Auto On indicator light remains off, switch on the audio source and increase its
output level until the red indicator light comes on.
HEADPHONE
1.
Two rechargeable LR03/AAA size batteries have been built-in in the battery
compartment and no insertion is required.
OPERATION
1.
Switch on the sound source (TV set or audio component) that the
transmitter is connected to.
2.
Place the headphones On/Off switch in the On position.
3.
Place the headphones on your head and adjust the volume to obtain the
desired sound level.
4.
If you cannot find the best reception frequency, press the "Auto Scan"
button on the headphones. The corresponding indicator light will come on.
5.
Press “SRS” button to activate Surround Effect for unique audio
enjoyment.
, SRS and
symbol are trademarks of SRS Labs, Inc.
NOTE:
You should then be able to move around freely from one room to another without
any interference. If interference does occur (interruptions in the signal), press
the "Auto Scan" button once to find a better reception channel.
For better stereo reception, stay approximately seven meters away from
the transmitter when you press the "Auto Scan" button.
If it is impossible to find a satisfactory frequency, change the setting on
your transmitter, then press the "Auto Scan" button on the headphones to
find the corresponding channel.
To both protect the transmitter and save power, the transmitter automatically
switches off after approximately one minute if the signal that it receives from the
audio source is too weak for proper reception. If however the signal returns to an
acceptable level, then the transmitter automatically switches back on.
CHARGING THE BATTERIES
1. Place the On/Off switch on the receiver headphones in the Off position.
2. To recharge the headphone batteries, place the headphones on the
transmitter, taking care to ensure that the charge contacts touch the
transmitter's charge prongs.
3. The charge process starts automatically and the green indicator light comes
on. Be sure to charge new batteries for 24 hours before using them for the
first time in the headphones.
WARNING:
Never attempt to recharge conventional dry cells.
Never use another type of battery or non-rechargeable batteries to replace the
rechargeable (LR03/AAA) batteries supplied. When the headphones are not in
use, move the switch to the OFF position to avoid damaging the batteries.
The batteries must always be fully charged before use. An initial 24 hour charge
is required to guarantee an acceptable service life for the rechargeable batteries.
Always ensure that the headphones are switched to the Off position while the
batteries are charging.
IMPORTANT:
This unit can be operated with rechargeable batteries only. When replacing the
batteries or when disposing of the unit, always comply with applicable laws
relating to the disposal of batteries. Please place them in a proper disposal
container
to
ensure
that
they
are
environmentally-friendly way. Thank you.
eliminated
safely
and
in
an
REPLACING BATTERIES
Rechargeable batteries have a long service life. If it is however necessary to
replace them, proceed as described below:
Carefully
remove
the
cloth
padding
around the left and right headphones.
Install the new batteries in their housings
as illustrated. Check for correct +/polarity.
Bring the cloth padding up over the sloped
guide slot. Hold it in place with your thumb
just after the slope to ensure that it does
not leave the guide.
Turn the padding as illustrated. It will slide
into the guide slot by itself. Keep turning it
until it is correctly in place. Once it has
taken on an oval shape, then it is correctly
positioned.
Only use rechargeable batteries of the type specified under the “Technical
specifications” heading.
The rechargeable batteries supplied with the headphones must absolutely not
be taken apart, disposed of in an open fire or short circuited.
TECHNICAL SPECIFICATIONS
Transmission mode
: UHF stereo
Carrier frequency
: 900Mhz
Operating voltage
: Transmitter – 12.5 V 150 mA
Receiver
– 2.4 V (two rechargeable batteries,
LR03/AAA size)
Frequency response
: 30 Hz – 11 KHz
Distortion
: 1%
Signal-to-noise ratio
: 55 dB
Channel separation
: 30 dB)
Range
: 165 feet max.
This Device complies with Part 15 of the FCC Rules. Operation of this device is subject
to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
WARNING:
Modification of this device to receive cellular radio-telephone service signals is
prohibited under FCC rules and Federal Law.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment
TROUBLESHOOTING
NO SOUND
Ensure that the mains adapter is pushed fully into the power outlet
and that its cable is properly connected to the DC IN 12V connector
on the transmitter.
Ensure that the headphones On/Off switch is switched to the On.
The headphones battery charge level may be too low. Recharge the
batteries or replace them with fully charged batteries.
Ensure that your TV set, Hi-Fi system or audio component is switched
on and set to a channel that broadcasts an audio signal.
Use the headphones volume control to increase the sound level.
The connected audio/video equipment may not be in playback mode.
Start playback on by the equipment.
Check the battery compartments if batteries are at right positions.
DISTORTION
Ensure that the "Stereo" indicator is lit. If not, adjust the tuning control
(Auto Scan) on the headphones until it lights.
Use the channel selector to change the transmitter's transmission
frequency. Then you will need to adjust the tuning control on the
headphones until the "Stereo" indicator comes on.
The headphones battery charge level may be too low. Recharge the
batteries or replace them with fully charged batteries.
Ensure that the volume knob setting is correct.
The headphones may be too far away from the transmitter. Move
closer to it.
The audio signal input level is too low. Increase the volume from the audio
source.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 2004:04:14 23:05:58
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2004:04:14 23:05:59+08:00
Page Count                      : 8

EXIF Metadata provided by EXIF.tools