Cobra Electronics PR900DX GMRS Held To Face User Manual

Download:
Mirror Download [FCC.gov]
Document ID	151714
Application ID	EufV6Re6GrB2heiDlvOvVA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	66.75kB (834422 bits)
Date Submitted	2001-05-25 00:00:00
Date Available	2001-06-29 00:00:00
Creation Date	2001-05-01 12:33:58
Producing Software	Acrobat 4.05 Scan Plug-in for Windows
Document Lastmod	2001-05-24 13:50:45
Document Title	Users Manual
Document Creator	Acrobat 4.05 Scan Plug-in for Windows

Safety information For UNIT
Your Wireless handheld portable transceiver contains a low power
transmitter.
When the Push-to Taik(P’lT) button ls pushed it sends out radio
trequency (RF) signals. This device is authorized to operate at a duty
factor not to exceed 5036.
In August 1996, the Federal Communications Commission (FCC) adopted
RF exposure guidelines with safety levels tor hand-held wireless devices.
important Note: To maintain compliance with the FCC's RF
exposure guidelines, hold the transmitter and antenna at least 1 inch (2.5
centimeters) from your face and speak in a normal voice, with the antenna
pointed up and away from the lace.
Ii you wear the handset on your body while using the headset accessory,
use only the manufacturers supplied belt clip tor this product and ensure
that the antenna is at least 1 inch(2.5 centimeters) trom your body when
transmitting.
Use only the supplied antenna. Unauthorized antennas, modifications, or
attachments could damage the transmitter and may violate FCC
regulations.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANV INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDERSIRED
OPERATION
3. OPERATION
3.1 ICONS on LCD
‘MG
“-
90:0 3
W N m
TIIII- saw
fit
1) Key lock indicator: Indicates that the key lock function is in use.
2) Receive signal indicator : Appears when receiving signal or squelch
noise is existing.
3) Monitor indicator : Appears when v‘" "TC“ ‘sn‘t in use and
squelch is open.
4) Emergency channel indicator : Indicates while receiving a emergency channel.
5) Scan indicator : Indicates that scan is enabled.
6) CTCSS indicator : Appears when the CTCSS function is in use
7) Priority scan indicator 1 Indicates that the priority scan function is in use.
8) Beep ON/OFF indicator : Appears while key tone is in use.
9) Battery indicator: Indicates the battery status
10) CTCSS readout : Shows the operating CTCSS frequency or code.
1 l) BCLO (Busy Channel Lock Out) Indicator : Appears to inhibit transmitting
whenever there is another conversation is on the channel.
I2) VOX (Voice Activated Transmit) Indicator : Turning on the
power while pressing PTT button activates VOX function.
13) Channel readout : Shows the current channel number.
14) Skip channel indicator : Appears when a non-select scan
channel is selected.
COBRA ELECTRONICS COR
P,
FCC ID : BBOPRQOODX
JOB # : 432AKI
EXHIBIT {it : 15 A J, z,
3.2 Key Function
1) Volume controls 1 Turn the power on and adjusts the audio level.
2) PTT switch : Push and hold to transmit ; release to receive.
3) Monitor/ Lamp Key : Press and hold this key for over 2 seconds to enable
the receive CTCSS feature And Push this button
momentarily to switch on for off the LCD back»lightingr
4) Channel Up/Down key : Push to select the operating channel Push and hold
to change the current channel rapidly.
5) Mode (Function) key : Push to select the following function setting mode.
Btiefpress mode : l'st press -- CTCSS 2’nd press -- VOX level ,
3’rd press -- Scan skip list 4'th press — Beep ON/OFF,
5’th press -~ BCLO ON/OFF 6‘th press --Priority channel
7’th press — Squelch level.
Lon ress mode : Function settin mode continue 1
6) Scan / Eek key : Push this key to mgmentarily to enafiey or disable the
scan Press and hold this key for over ZSeconds to look or
unlock keypad.
7) Emergency Channel key : Push this key to momentarily change to
emergency channel (462,6750Mhz).
8) Speaker / Microphone
9) External DC power jack : Connect a 4.8 to 6,5V DC power source with the
cable to the GCH-lZONC wall charger for charging.
10) LCD (Liquid Crystal Display)
11) Transmit indicator : Light red while transmitting.
12)Extemal speaker/mic jacks : Connect an optional speaker/mic or headset,
if desired. The internal mic and speaker will not function when
either is connected.
2) Function display
lid“
l\/I' N
EMG
P H l 1. "1
1) Key lock indicator : Indicates that the key lock function is in
2) Receive signal indicator : Appears when receiving signal
or squelch noise is existing .
3) Monitor indicator : Appears when any CTCSS
isn‘t in use and squelch is open.
4) Emergency Channel indicator : Appears when emergency
channel is in use,
5) Scan indicator : Indicates that scan is enabled.
6) CTCSS indicator: Appears when the CTCSS function is in
use.
7) Priority scan indicator: Indicates that the priority scan function is
in use .
8) Beep ON/OFF indicator : Appears while key tone is in use.
9) Battery indicator : Indicates the battery status.
10) CTCSS Frequency readout : Shows the operating CTCSS
frequency
11) BCLO (Busy Channel Lock Out) Indicator : Appears to
inhibit transmitting whenever there is another
conversation on the channel.
12) VOX (Voice Activated Transmit) Indicator : Turning on the
power while Dressing PTT button activates VOX function.
13) Skip channel indicator : Appears when a non-select scan
channel is selected.
14) Channel readout : Shows the current channel number .
3-3. SETTING AND OPERATION
1) Basic Channel Selection
In order to communicate with other GMRS units, both you and the
receiving party must be on the same channel.
PR-900 has lSchannels indicated by the large digits on the
LCD display panel. Before trying to transmit on the selected channel,
you should press the Monitor Button to check the activity on that channel.
If someone is already on the selected channel, you should try another
channel that is clear
To change the basic channel,
-. In the standby mode, press the Up Button briefly to move to the next
higher main channel number.
». Press the Down Button briefly to move to the next lower main
channel number.
2) Sub Channel Selection
CTCSS (Continuous Tone Coded Squelch System) with 38 Sub-Frequency.
This feature allows you to utilize a less used channel range (00 ~ 38) within
a main channel,
This enables you to communicate with another party on the same main
Channel using the same sub—code,
This helps to avoid congestion on the main channel and filters out unwanted
Noise and static, v“
There are 38 CTCSS Sub-channels for each main channelt
To change the CTCSS Sub-channel,
-. Press the Mode Button until the Icon (CTC) appears in the LCD panel.
-. Press the Up Button or Down Button to choose the desired sub-channel
to use,
-. The corresponding sub-code frequency will be displayed in the lower
right comer.
«. Press the PTT Button to confirm your selection.
NOTE : To communicate with other GMRS units, they must be switched to
the same channel and C TCSS sub-code. To communicate
with other GMRS units that do not have sub-codes, switch your unit
to the same channel with the sub-code set to OFF
3) Auto Channel Scan List Selection Mode
This feature allows you to scan for an active channel and communicate with
the party transmitting.
To access the Auto Channel Scan Skip List menu,
. Press the Mode Button until the Icon (SKIP) blinks on the LCD panel.
. Press the Up Button to choose the desired Scan access channel, or
Down Button to choose the desired Scan skip channel.
, Press the PTT Button to confirm your selection.
. The unit will begin scanning for an active main channel.
4) Priority Scan Channel Selection Mode
This feature allows you monitor one special channel and all scan channels at
the same time. If you pre-set any priority channel other than the current
channel in use, the pre—set channel will be scanned every 0.5 second and
signals you when a call is received.
To access the Priority Scan menu,
-. Press the Mode button until the (PRIO) icon blinks on the LCD panel.
». Press the Up button or Down button to select the desired channel number
You wish to closely monitor.
-. Press the FTT button to confirm your selection,
-. To turn off the Priority Scan feature while scanning mode, simply press the
Scan button once. 1‘
5) VOX Selection Mode
The Voice Activated Transmission (VOX) function allows your voice to
activate transmission automatically when the Communicator is used with the
optional hands-free mic/head-set (refer to enclosed Accessory Order Form).
It also allows hands-free use when a mic/head-set is not being used without
having to the PTT button.
To access the VOX Selection menui
-. Press the Mode button until the VOX icon blinks and (V0 01) appears on
the LCD Panel.
-. Press the Up button or Down button to select from 01 ~ 10 Voice Level.
-. 01 ~ 10 Level setting determines VOX response sensitivity.
-. Press the PTT button to confirm your selection.
—i To turn on the VOX feature, press PTT button + Power ON,
-. To turn off the VOX feature, Power ON again
6) Auto Key Lock Selection Mode
This feature prevents accidental channel change and disturbance to the
preferred settings of the communicator. Auto Key Lock temporarily
disables to Up,Down and PTT button.
To access the Auto Key Lock selection menu,
-, Press and hold the Scan button for over 2 seconds to Lock or Unlock the
Key except PTT and On/Off switch.
7) BCLO (Busy Channel Lock Out) Selection Mode
This feature inhibit transmitting whenever there is another conversation is
on the same channel
To access the Busy Channel Lock Out selection menu,
-. Press the Mode button until the BCLO icon blanks on the LCD panel
-. Press the Up button or Down button to select the BCLO ON/OFF option.
-. Press the PTT button to confirm your select.
8) Call Ringer Selection Mode
This feature provides 5 user selectable call ringer signal to alert you of a
callong partyi
To select your favorite call ringer signal. it
». Press Emergency button + Power ON. Appears the (C 01 ) icon blanks
on the LCD panel.
-. Press the Up button or Down button to preview the 5 available signal“
». Press the PTT button to confirm your selection.
-. To quickly activate the Call , Simply press PTT button 2 time click.
9) TOT(Time Out Timer) Selection Mode
This feature is sometimes necessary or desirable to restrict a single transmission
to a specific maximum times,
This feature can be useful when particularly trying to conserve battery Poweri
To access the Time Out Timer selection menu,
-. Press Mode button + Power ON . Appears the (T OFF) on the LCD panel
~. Press the Up button or Down button to select the 305m,605ec,180sec or Off.
-4 Press the PTT button to confirm your selection.
10) Emergency Channel Mode
The Emergency Channel can be used to special frequency ( lOChannel :
462.6750Mhz) within your transceiver. No matter what mode the transceiver
is in, the, Emergency Channel always can be Selected quickly.
To access the Emergency Channel mode,
-A Press Emergency button , Appears the (EMG) and 10 channel readout
on the LCD panel.
-. To turn off the Emergency Channel feature while Emergency Channel mode,
simply press the Emergency button once

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2001:05:24 13:50:45-04:00
Create Date                     : 2001:05:01 12:33:58-07:00
Creator                         : Acrobat 4.05 Scan Plug-in for Windows
Producer                        : Acrobat 4.05 Scan Plug-in for Windows
Page Count                      : 8

EXIF Metadata provided by EXIF.tools