Cobra Electronics XRS9530 RADAR DETECTOR User Manual 9300 1a

Cobra Electronics Corporation RADAR DETECTOR 9300 1a

USERS MANUAL

Important Information and Customer AssistanceIntroductionA1 EnglishImportant Information •Federal Laws Governing the Use of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra radar/laser detector. The Communications Act of 1924 guarantees your right to receive radio transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action.Safety AlertUse of this product is not intended to, and does not, ensure that motorists orpassengers will not be involved in traffic accidents. It is only intended to alert the motorist that an emergency vehicle equipped with a Cobra Safety Alert transmitter is within range as defined by that product. Please call local fire and police departments to learn if coverage exists in your area.Safe Driving Motorists, as well as operators of emergency or service vehicles, are expected toexercise all due caution while using this product, and to obey all applicable traffic laws.Security of Your Vehicle Before leaving your vehicle, always remember to conceal your radar detector in order to reduce the possibility of break-in and theft.Customer Assistance •Should you encounter any problems with this product, or not understand its many features,please refer to this owner’s manual. If you require further assistance after reading thismanual, Cobra Electronics offers the following customer assistance services:For Assistance in the U.S.A. Automated Help Desk English only. 24 hours a day, 7 days a week 773-889-3087 (phone).Customer Assistance Operators English and Spanish. 8:00 a.m. to 6:00 p.m. CT Mon. through Fri. (except holidays) 773-889-3087 (phone).Questions English and Spanish. Faxes can be received at 773-622-2269 (fax).Technical Assistance English only. www.cobra.com (on-line: Frequently AskedQuestions). English and Spanish. productinfo@cobra.com (e-mail).For Assistance Outside the U.S.A. Contact Your Local Dealer ©2005 Cobra Electronics Corporation6500 West Cortland StreetChicago, Illinois 60707 USAwww.cobra.comCustomer AssistanceXRS 953012 BAND™HIGH-PERFORMANCE DIGITAL RADAR/LASERDETECTOR WITH XTREME RANGE SUPERHETERODYNE®TECHNOLOGYNothing Comes Close to a Cobra®EnglishOperating Instructions Printed in China Part No. 480-232-PVersion ANothing Comes Close to a Cobra®EnglishFor more information or to order any of our products, please visit our website:www.cobra.comCB RadiosmicroTALK®RadiosRadar/Laser Detectors Safety Alert®Traffic Warning SystemsHandheld GPS ReceiversMobile GPS Navigation SystemsHighGear®Accessories CobraMarineTM VHF Marine Radios Power InvertersAccessories The Cobra line of quality products includes:
Important Information and Customer AssistanceIntroduction Order FormNothing Comes Close to a Cobra®25Customer AssistanceDisplay and Product FeaturesIntroductionNothing Comes Close to a Cobra®A3Xtreme Range Superheterodyne TechnologyWith super-fast sweep circuitry, XRS provides extra detection range and the best possible advance warning to even the fastest radar gunsDetection and Separate Alerts For: Radar signals (X, K,Ka and Ku bands, with signal strength indicated), laser signals, Safety Alert signals, Strobe Alert signals, Spectre 1 signals,VG-2 signalsLaserEye For 360° detection of laser and strobe signalsInstant-On Ready Detects radar guns with “instant-on”(very fast) speed monitoring capabilitiesTone Alert or Voice Alert With adjustable volumeDigiView Data Display With easy-to-read alpha/numeric dotmatrix text readoutCity or Highway Modes to reduce false alertsSafety Alert Traffic warning system distinguishesimportant safety alerts from other K band signalsStrobe AlertEmergency vehicle warning systemManual Mute or Auto Mute A mute function of audio alertsIntelliMute A mute function which automatically reduces false alerts by sensing engine RPMsMounting Mounts easily on windshield or dashboardProduct Features •Congratulations! You’ve made a smart choice by purchasing a highperformance radar/laser detector from Cobra. Just look at some of thesophisticated features and capabilities your new unit includes:Display •This booklet describes the simple steps for mounting and setting up your detector. It also provides helpful information about how radar and laser guns are used and how you can interpret the alerts you receive.Alpha/Numeric Dot Matrix Text DisplaySee pages 6 – 16 for more information aboutdisplay features.hControls, Indicators and ConnectionsIntroductionA2 EnglishControls, Indicators and Connections •12V DCPower JackOn-Off/ Volume ControlAllows you to adjust thevolume of the tone alerts.IntelliMute ButtonEngine RPM sensing mute functionwhich reduces false alerts. Button turns IntelliMute on and off. (Also enters IntelliMute setting mode.*)LaserEye For 360° detection of laser and strobe signals.Windshield Bracket Release ButtonMute ButtonFor manual mute or auto muteof audio alerts. (Also turns VoiceAlert on and off.*)* Press and hold for two seconds toaccess these functions.WindshieldBracket MountWARNINGModifications or parts substitutions not approved by Cobra Electronics Corporation may violate FCC Rules and void your authority to operate this equipment.Dim Button Allows you to adjust theDigiView Data Displaybrightness for easy reading. (Also turns Spectre 1 and VG-2alerts on and off.*)Order Form •NameAddress (No P.O. Boxes)City State/Province Zip CountryTelephoneCredit Card Number Type: ❒Visa ❒MasterCard ❒Discover Exp. DateCustomer SignatureItem # Description U.S. Cost Each Qty Amount420-030-N-001 Straight 12V Power Cord420-026-N-001 Coiled 12V Power Cord545-139-N-001 Windshield Mounting BracketCLP-2B Dual Port Power AdapterU.S. Subtotal(Tax if Applicable)Shipping/HandlingTotalOrdering From U.S.A.Call 773-889-3087 for pricing or visit www.cobra.com.For Credit Card OrdersComplete and return this order form to fax number 773-622-2269. Or call 773-889-3087 [Press one from the main menu] 8:00 a.m. to 6:00 p.m. Central Time, Monday through Friday (except holidays).Make Check or Money Order Payable ToCobra Electronics, Attn: Accessories Dept., 6500 West Cortland Street, Chicago, IL 60707 U.S.A.To Order OnlinePlease visit our website: www.cobra.comAmount Shipping/Handling*$10.00 or less . . . . . $3.00$10.01-$25.00 . . . . . $5.50$25.01-$50.00 . . . . . $7.50$50.01-$90.00 . . . . $10.50$90.01-$130.00 . . . $13.50$130.01-$200.00 . . $16.50$200.01 plus . . . . . 10% ofpurchaseTax TableWisconsin add 5%Indiana, Michigan, Ohio add 6%California add 7.25%Illinois add 9% *For AK, HI and PR add additional $26.95 for FedEx Next Day or $10.95 for FedEx 2nd Day. Excludes weekends and holidays shipments.Please allow two to three weeks for delivery in the U.S.A. Prices subject to change without notice.Audio JackCity Button For City or Highwaymodes to reducefalse alerts.Speaker
Nothing Comes Close to a Cobra®1ContentsIntroductionIntroductionImportant Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1Customer Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1Controls, Indicators and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3Your DetectorInstallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Highway/City Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6DigiView Data Display Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Muting an Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Auto Mute Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8IntelliMute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Voice/Tone Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Spectre 1 and VG-2 Alert Audio Settings & Ku Band Detection . . . . . . . 13Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Signals Detected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Audio Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Visual Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Instant-On Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Responding to Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Understanding Radar and Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21WarrantyLimited 1-Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Customer AssistanceProduct Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Trademark Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Order Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Nothing Comes Close to a Cobra®InstallationYour Detector3InstallationYour Detector2EnglishInstallation •Where to Mount Your UnitYou will get optimum performance from your detector if you Mount it at apoint approximately in the center of the vehicle, as low as possible on thefront windshield without obstructing the unit’s view of the road either to the front or rear. Make sure the unit is level with the road.You can also mountit directly on the dashboard. The unit’s lens must not be blocked and the LaserEye should have a clear viewout the back window to allow 360° detection.Radar and laser signals pass through glass but not through other materialsand objects. Objects that can block or weaken incoming signals include: ■Windshield wiper blades■Mirrored sun screens■Dark tinting at the top of the windshield■Heated windshields currently available on some vehicles (Instaclear for Ford, Electriclear for GM.) Consult your dealer to see if you have this option.1. Attach the rubber cups to the bracket.2. Make sure the rubber cups and your windshield are clean.3. Push the bracket firmlyonto the windshield.4. Attach the detector to the bracket. Check the angle of the unit.5. To adjust the angle ifnecessary, gently push orpull on the bracket to bendit. DO NOT use the detectorto bend the bracket.6. Plug the power cord into the detector.7. Plug the cigarette lighteradapter on the power cord into your vehicle’scigarette lighter.8. You can temporarily remove the detector whenever you wish by pressing the bracket release button and sliding it off the bracket.Windshield MountingThe LaserEye Should Have a Clear ViewWindshield Mounting Dashboard Mounting
Getting Started and SettingsGetting Started •Your DetectorNothing Comes Close to a Cobra®5InstallationYour Detector4English1. Place the detector on the dashboard to find a location where the unit has a clear, level view of the road. The angle can NOT be adjusted after mounting.2. Remove the paper backingfrom one side of the hook-and-loop fastener.3. Attach the pad to thedashboard at your chosenlocation and remove the other paper backing.4. Attach the detector to thehook-and-loop fastener. You can remove andreattach the unit as often as you like.6. Plug the power cord into the detector.7. Plug the cigarette lighteradapter on the power cord into your vehicle’scigarette lighter.Dashboard MountingSystem ReadyPower OnTestingVoice AlertOn-Off/Volume ControlRotate clockwise (away from you)NOTEIn some vehicles, power is supplied to the cigarette lighter even while the ignition is off. If this is the case with your vehicle, you should turn off or unplug your detector whenparking for lengthy periods.Secondary IconsTo Turn On the Unit and Adjust the Audio VolumeRotate the On-Off/Volume control clockwise (away from you).Tone Voice Visual DisplayThree beeps Testing, then three beepsSystem Ready, thenVoice AlertThe display willcycle through theuser mode settings(Voice Alert,Spectre 1 and VG-2,IntelliMute, City Xor Highway status).Start-up is complete when the display continuously shows the letters indicating the current user settings (c= City mode, h= Highway mode, i= IntelliMute on)Start-Up CompletehSettings •When changing the Settings on your detector, please keep in mind:■Buttons can have multiple functions.■Depending on your choice of Voice Alert or Tone Alert mode, you willhear either voice messages or tones confirming changes in settings. ■All settings will be stored in memory when the power is turned off and recalled when the power is turned back on.
SettingsYour DetectorNothing Comes Close to a Cobra®7SettingsYour Detector6EnglishHighway/City ModeSetting your detector to City mode delays all X band audio alerts until the signal strength reaches Level 3. (A single beep will sound when the signal is first detected.) This will reduce false alerts while you are driving in, or near, urban areas where there are many sources for conflicting X band signals such as microwave towers and automatic door openers. To change settings, follow the procedure listed below, which indicates what you will see and hear (either in Voice Alert or Tone Alert mode) as you complete each step. The factory setting is Highway mode.City ModeHighway ModeTo Change From Highway Mode to City ModePress and release the City button. Tone Voice Visual DisplayOne beep City cappears in the displayTo Change From City Mode Back to Highway ModePress and release the City button again. Tone Voice Visual DisplayTwo beeps Highway happears in the displayhcDigiView Data Display BrightnessYou can choose from four (4) settings for Brightness of the display. You can cycle through the settings by repeatedly pushing the Dim button. The factory setting is Bright.Dim ButtonPress andreleaseBrightDark DimDimmerPress andrelease Dim buttonTo Change the Brightness to DimPress and releasethe Dim buttononce.Tone Voice Visual DisplayOne beep Dim Display dimsTo Change the Brightness to DimmerPress and releasethe Dim buttonagain.Tone Voice Visual DisplayNone Dimmer Display dims furtherTo Change the Brightness to DarkPress and release the Dim button a third time.Tone Voice Visual DisplayOne beep Dark Display remainsdim (no visualalerts will be seen)To Change the Brightness to BrightPress and release the Dim button a fourth time.Tone Voice Visual DisplayTwo beeps Bright Display returns to full brightnessDark Indicator.City ButtonPress and release
SettingsYour DetectorNothing Comes Close to a Cobra®9SettingsYour Detector8EnglishMuting an AlertYour detector allows you to quickly turn off an audio Alert by momentarilypressing the Mute button. If you press the Mute button a second time during the Alert, the audio Alert will be turned back on.Auto Mute ModeAuto Mute will automatically reduce the audio volume of all alerts after four seconds for as long as the signal is detected. The factory setting for Auto Mute is on.IntelliMuteIntelliMute is a unique new feature that allows you to avoid alerts you don’t need to hear because you are stopped or moving slowly. By sensing the “revs” (RPMs) of your engine, IntelliMute knows when you are at lowspeed and automatically mutes alerts (except for strobe signals fromemergency vehicles).Before IntelliMute will work, you must set an activation point for your engine’srevs (see page 11). Whenever the revs are below that point, IntelliMute willbegin muting. The activation point will be stored in memory and recalled each time the power is turned on. The factory setting is IntelliMute off.NOTEIntelliMute may not work with some vehicles because it cannot sensethe engine’s revs. In such cases, you can reduce unwanted audio alertsby using Auto Mute and City mode when appropriate.IntelliMute ButtonPress and releaseMute ButtonPress and releaseTo Turn Auto Mute OffPress and release the Mute button while no alert is occurring.Tone Voice Visual DisplayOne beep Auto Mute Off NoneTo TurnAuto Mute OnPress and release the Mute button again while no alert is occurring.Tone Voice Visual DisplayTwo beeps Auto Mute On NoneTo Turn IntelliMute OnPress and release the IntelliMute button.Tone Voice Visual DisplayTwo beeps IntelliMute On iappears in the displayTo Turn IntelliMute OffPress and release the IntelliMute button again.Tone Voice Visual DisplayOne beep IntelliMute Off NoneIntelliMute Onih
To Set the IntelliMute Activation PointPress and hold the IntelliMutebutton for two seconds.Tone Voice Visual DisplayTwo beeps Set Engine Revs Press IntelliMute button again at desired RPMsRev your engine tothe level you wish to set (recommendslightly above idle)and hold revs steadyfor two seconds. None None NoneAt the desired rev level, press and release theIntelliMute button.Three beeps IntelliMute Set IntelliMute Set!SettingsYour DetectorNothing Comes Close to a Cobra®11SettingsYour Detector10 EnglishWhat to Remember While Using IntelliMuteIntelliMute works with both City and Auto Mute modes.Whenever engine revs are below the activation point, an arrow pointing down will appear in the display. Above the activation point, an arrow pointing up will appear.If, for any reason, the unit stops sensing your engine’s revs, IntelliMute will indicate an error and automatically turn off.The rev point you set will be stored in the unit’s memory when power is turned off and recalled each time the power is turned on.NOTEThe rev point must be reset if you use your detector in a different vehicle.NOTEWhen initially choosing your IntelliMute activation point, a setting of approximately 300 to 600 RPMs above idle is recommended. You can reset the activation point at any time to fit your individualpreferences and driving style.Setting the IntelliMute Activation PointYour detector must be installed in your vehicle.CAUTIONDo not attempt to set the rev point while driving. Your vehicle should be parked and idling. IntelliMute must be turned on before setting the activation point. Dependingon whether the unit is in Tone Alert or Voice Alert mode, you will hear aseries of beeps or voice messages as you follow the steps on page 11.Tone Voice Visual DisplayFour beeps IntelliMute NotSet, Please TryAgain followed byIntelliMute not setPlease try againOne beep IntelliMute Off IntelliMute OffNOTEIf the unit is unable to sense usable pulses within threeseconds or if you do not set a rev point within 20 seconds of beginning these steps, IntelliMute will indicate an errorand automatically turn off.Below Activation PointihAbove Activation PointihPress Int...button ag...desired RPMsHold IntelliMute ButtonIntelliMuteSet!Rev Level SetIntelliMu...Please tr...IntelliMuteNot SetIntelliMuteOffIntelliMute OffIntelliMute ButtonPress and hold for two seconds
SettingsYour DetectorNothing Comes Close to a Cobra®13SettingsYour Detector12 EnglishSpectre 1 and VG-2 Alert Audio Settings & Ku Band DetectionThe detector is undetectable by police Spectre 1 and VG-2 radar detector detectors andwill alert you when such a device is in use near your vehicle. During the alert, the unitcontinues to detect other signals. You can choose whether or not you want your unit toshow Spectre 1 and VG-2 alerts. The factory setting is Spectre 1 and VG-2 alert on.The new Ku band may be introduced to North America in the future. To prevent false alerts until it is, the factory default for Ku band detection is off.Dim ButtonPress and hold for two secondsVoice/Tone SettingYou can set your detector to sound alerts with either a Voiceor a Tone. You can change settings by using the Mute button. In Voice Alert mode, you will first hear several tones, then a voice message announcing the type of signal detected, followed by more tones. In Tone Alert mode, you will hear the tones only.The factory setting is Voice Alert mode.Mute ButtonPress and hold fortwo secondsTo Change From Voice Alert to Tone AlertWhile no signal is being detected, press and hold the Mute button for two seconds.Tone Voice Visual DisplayOne beep Tone Alert NoneTo Change From Tone Alert Back to Voice AlertWhile no signal is being detected, press and hold the Mute button for two secondsagain.Tone Voice Visual DisplayNone Voice Alert NoneTo Turn Spectre 1 and VG-2 Alerts Off and OnWhile no signal is being detected, press and hold the Dim button for two seconds.Tone Voice Visual DisplayOne beep Spectre VG-2 OffSpectre1 & VG 2 OffTwo beeps Spectre VG-2 OnSpectre1 & VG 2 OnTo Turn Ku Band Detection On or OffTone Voice Visual DisplayTwo beeps Ku On Ku OnOne beep Ku Off Ku OffSpectre 1 and VG-2 OffSpectre1& VG2OffSpectre 1 and VG-2 OnSpectre1& VG2OnWhile no signal is being detected, press and hold theDim button for twoseconds to setSpectre 1 and VG-2alerts on or off.Then, press and holdthe Dim button fortwo seconds again.
DetectionYour DetectorNothing Comes Close to a Cobra®15DetectionYour Detector14 EnglishX Signal Detected K Signal Detected Ka Signal DetectedRadar Signals, Voice and Visual DisplaysType of Signal Voice Visual DisplayX Band Radar X Alert X and Signal StrengthK Band Radar K Alert K and Signal StrengthKa Band Radar Ka Alert Ka and Signal StrengthKu Band Radar Ku Alert Ku and Signal StrengthLaser Signals, Voice and Visual DisplaysType of Signal Voice Visual DisplayLTI 20-20* Laser Alert Laser 20/20LTI Ultra-Lyte* Laser Alert Laser UltraLyteKustom Signals ProLaser* Laser Alert Laser Pro LaserKustom Signals ProLaser III* Laser Alert Laser Pro Laser 3* Your detector provides 360˚ detection of these signals.NOTEBeep rate changes with different laser alerts.Detection •Signals DetectedThe tables on the following pages show you the types of Signals your detectorwill detect, as well as the voice and visual alerts it provides for each of them.Audio AlertsIn Voice Alert mode you will first hear several tones, then a voice messageannouncing the type of signal detected, followed by more tones. In Tone Alertmode, you will hear the tones only.In both Voice Alert and Tone Alert modes, a distinctly different alert tone isused for each type of signal detected (including separate tones for each lasersignal). For X, K, Ka and Ku band radar signals, the tones will repeat faster as you approach the signal source. The repeat rate of the tones gives you usefulinformation about the signal detected. (See responding to alerts on page 17.)Visual DisplayAn indication of the type of signal detected will appear in the DigiView DataDisplay. During X, K, Ka and Ku alerts, you will also see from 1 to 5 verticalbars, indicating the strength of the signal detected.Signal Strength ChartSignal Strength = 1(Weakest Signal)-Signal Strength = 2-- -Signal Strength = 3-------Signal Strength = 4------------Signal Strength = 5(Strongest Signal)--_------ - -- - - -----_X2--- K-3------ --_--Ka ---5-----------_Ku Signal Detected_-Ku --4---------LTI 20-20Laser20/20LTI Ultra-LyteLaserUltraLyteKustom SignalsProLaserLaserPro LaserKustom SignalsProLaser IIILaserPro Laser 3
Description Interpretation RecommendedResponseTone repeats slowly atfirst, then speeds uprapidly.Probably police radar FULL ALERTTone sounds one time only. Probably a false alarm, but possibly pulsed radar,Spectre 1 or VG-2 nearbyExercise cautionTone instantly begins repeating rapidly. Radar, Spectre 1 or VG-2nearby has been activatedsuddenlyFULL ALERTTone repeats slowly as youapproach a hill or bridge,then speeds up sharply asyou reach it.Probably police radar beyond the hill or bridgeFULL ALERTTone repeats slowly for a short period. Probably a false alarm Exercise cautionAny type of laser alert. Laser alerts are never false alarms FULL ALERTAny Safety Alert or Strobe Alert. You are nearing anemergency vehicle,railroad crossing, or road hazard(construction, accident, etc.)Exercise cautionDetectionYour DetectorNothing Comes Close to a Cobra®17DetectionYour Detector16 EnglishInstant-On DetectionYour detector is designed to detect Instant-On speed monitoring signals,which can suddenly appear at full strength.NOTEYou should take appropriate action immediately whenever an instant-on alert is given.Responding to AlertsStrobe and Safety Alert Signals, Voice and Visual DisplaysType of Signal Voice Visual Display3M Opticom or Tomar* Emergency Vehicle Approaching Emergency VehicleEmergency Vehicles Emergency Vehicle Approaching Emergency VehicleRoad Hazards Road Hazard Ahead Road HazardTrains Train Approaching Train* Your detector provides 360˚ detection of this signal.VG-2 Alert Signal, Voice and Visual DisplayType of Signal Voice Visual DisplayInterceptor VG-2 VG-2 Alert VG2NOTEThere are different tones for each Safety Alert.NOTEThere are different tones for each alert.NOTEThere are different tones for each alert.Emergency AlertSignal DetectedVG-2 Alert SignalDetectedVG2Spectre 1 Alert Signal, Voice and Visual DisplayType of Signal Voice Visual DisplaySpectre Spectre Alert Spectre1Spectre 1 Alert SignalDetectedSpectre1Road Hazard AlertSignal DetectedRoadHazardTrain Alert SignalDetectedTrainEmergency...Strobe Alert Display (Flashing)Emergency...
Understanding Radar and LaserYour DetectorNothing Comes Close to a Cobra®19Understanding Radar and LaserYour Detector18 EnglishUnderstanding Radar and Laser •Radar Speed Monitoring SystemsFour band frequencies have been approved by the Federal CommunicationsCommission (FCC) for use by speed monitoring radar equipment: X band 10.525 GHzK band 24.150 GHzKa band 33.400 – 36.00 GHzKu band 13.435 GHzYour detector detects signals in all four radar bands.Spectre 1 and VG-2Spectre 1 and VG-2 are “detector detectors” that work by detecting low-levelsignals emitted by most radar detectors. Your detector does not emit signalsthat can be detected by Spectre 1 or VG-2, but does detect Spectre 1 and VG-2signals and will alert you when a device is in use near your vehicle, if you so choose.Safety Alert Traffic Warning SystemFCC-approved Safety Alert transmitters emit microwave radar signals thatindicate the presence of a safety-related concern. Depending on the frequencyof the signal emitted, it can indicate a speeding emergency vehicle or train, or a stationary road hazard. Because these microwave signals are within the K band frequency, mostconventional radar detectors will detect Safety Alert signals as standard K band radar. Your detector, however, is designed to differentiate betweenstandard K band and Safety Alert signals, and give separate alerts for each.Safety Alert technology is relatively new. Safety Alert transmitters can be found in limited numbers in all 50 states, but the number is growing.Depending on your location, you may not receive these alerts regularly and may often encounter emergency vehicles, trains and road hazards without being alerted. As the number of transmitters increases, these alerts will become more common. When you receive such an alert, please watch for emergency vehicles ahead of you, on cross streets and behind you. If you see an emergency vehicleapproaching, please pull over to the right side of the road and allow it to pass.Strobe AlertSpecial strobes mounted on the light bars of authorized emergency vehicles (fire trucks, police cars, ambulances) automatically change trafficsignals as the vehicle approaches an intersection. These strobes and thespecial strobe detectors located on the traffic signals, introduced fairlyrecently by 3M and Tomar, are already in use in more than 1000 citiesnationwide. Cobra’s exclusive Strobe Alert detector will detect these special strobes and give an emergency vehicle alert. When you receive such an alert, please watch for an approaching emergency vehicle and pull over to allow it to pass. To inquire about coverage in your area, contact your local fire and police departments.LIDAR (Laser)The correct name for the technology that most people refer to as laser is actually LIDAR, which stands for Light Detection and Ranging.LIDAR operates much like radar. Its signal spreads out like a radar signal, though not as widely. Unlike radar, LIDAR must have a clear line of sight to its target vehicle throughout the entire measurement interval. Obstructions such as sign posts, utility poles, tree branches, etc., will prevent valid speed measurement.Some common questions about LIDAR include:■Does weather have any affect on LIDAR?Yes. Rain, snow, smoke, fog, or airborne dust particles will reduce the effective range of LIDAR and can, if dense enough, prevent its operation.■Can LIDAR operate through glass?Yes. Newer LIDAR guns can obtain readings through most types of glass.However, the laser pulse also can be received through glass to trigger an alarm by your detector.■Can LIDAR operate while in motion?No. Because LIDAR operates by line of sight, the person using it cannotdrive the vehicle, aim and operate the gun all at the same time.■Is LIDAR legal to use?Yes. It is legal in all 50 states.
SpecificationsNothing Comes Close to a Cobra®21Maintenance20 EnglishMaintenance •Maintenance of Your Radar DetectorYour detector is designed and built to give you years of trouble-free performance without the need for service.No routine Maintenance is required.If your unit does not appear to be operating properly, please follow these troubleshooting steps:■Make sure the power cord is properly connected.■Make sure the socket of your vehicle’s cigarette lighter is clean and free of corrosion.■Make sure the power cord’s cigarette lighter adapter is firmly seated in your cigarette lighter.■Check the power cord fuse. (Unscrew the ribbed end cap of the cigarette lighter adapter and examine the fuse. If required, replace it with a 2-amp fuse only.)Specifications •Band and FrequenciesBand FrequenciesX Band 10.525 ± 0.050 GHzK Band 24.125 ± 0.125 GHzSafety Alert 24.070 ± 0.010 GHzTraffic Warning 24.110 ± 0.010 GHzSystem 24.190 ± 0.010 GHz24.230 ± 0.010 GHzKa Band 34.700 ± 1.300 GHzKu Band 13.435 ± 0.050 GHzLaser 910 ± 50 nmStrobe 700 ± 300 nmUnit Dimensions and WeightDimensions* (H x W x D) Weight*11⁄3" x 23⁄4" x 41⁄3" 5.11 oz. (34 mm x 70 mm x 110 mm) (145 g)* Dimensions and weight measurements are approximate.This radar detector is covered by one or more of the following U.S. patents: 5,497,148; 5,594,432;5,612,685; 6,078,279; 6,094,148. Additional patents may be listed inside the product or pending. Your DetectorYour Detector
Product Service andTrademark AcknowledgementCustomer AssistanceNothing Comes Close to a Cobra®23Warranty22 EnglishLimited 1-Year Warranty •For Products Purchased in the U.S.A.Cobra Electronics Corporation warrants that its Cobra 12 Band Radar/Laser Detectors, and the component parts thereof, will be free of defects inworkmanship and materials for period of one year from the date of firstconsumer purchase. This warranty may be enforced by the first consumerpurchaser, provided that the product is utilized within the U.S.A.Cobra will, without charge, repair or replace, at its option, defective 12 BandRadar/Laser Detectors, products or component parts upon delivery to theCobra Factory Service Department, accompanied by proof of the date of firstconsumer purchase, such as a duplicated copy of a sales receipt.You must pay any initial shipping charges required to ship the product forwarranty service, but the return charges will be at Cobra’s expense, if theproduct is repaired or replaced under warranty.This warranty gives you specific rights, and you may also have other rights which vary from state to state.Exclusions: This limited warranty does not apply: 1. To any product damaged by accident. 2. In the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs. 3. If the serial number has been altered, defaced or removed. 4. If the owner of the product resides outside the U.S.A. All implied warranties, including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty.Cobra shall not be liable for any incidental, consequential or other damages;including, without limitation, damages resulting from loss of use or cost of installation.Some states do not allow limitations on how long an implied warranty lastsand/or do not allow the exclusion or limitation of incidental or consequentialdamages, so the above limitations may not apply to you.Product Service •For any questions about operating or installing this new Cobra product, or ifparts are missing…PLEASE CALL COBRA FIRST…do not returnthis product to the store! See customer assistance on page A1.If this product should require factory service, please call Cobra first at 773-889-3087 BEFORE sending the product. This will ensure the fastestturnaround time on any repair.If Cobra asks that the product be sent to its factory, the following must befurnished to have the product serviced and returned: 1) Send the completeunit, including power cord. (It is not necessary to include the mountingbracket.) 2) For warranty repair, enclose some form of proof-of-purchase,such as a photocopy or carbon copy of a sales receipt. If you send the original receipt, it cannot be returned. 3) Enclose a typed or clearly writtendescription of the problem you are having with your unit, plus the name andaddress where you want the unit returned. 4) Pack the unit securely toprevent damage during transit. If possible, use the original packing materials.5) Ship prepaid and insured using a traceable carrier such as United ParcelService (UPS), Federal Express, or Priority mail with delivery confirmation.Ship to: Cobra Factory Service, Cobra Electronics Corporation, 6500 WestCortland Street, Chicago, IL 60707 U.S.A. 6) Please allow three to four weeksbefore contacting us about the status of your service. Call 773-889-3087 forassistance. If your unit is under warranty, it will either be repaired or replacedupon receipt, depending on the model. If your unit is out of warranty, you willreceive a letter informing you of the repair or replacement charge.Trademark Acknowledgement •Cobra®, 6 Band®, 9 Band®, DigiView®, EasySet®, Extra Sensory Detection®, IntelliShield®, LaserEye®, Nothing Comes Close to a Cobra®, Safety Alert®Traffic Warning System, Strobe Alert®, VG-2 Alert®, Xtreme Range Superheterodyne®and the snake design are registered trademarks of Cobra Electronics Corporation, USA.Cobra Electronics Corporation™, 12 Band™, IntelliMute™, Revolution™ Series, RoadReady™,SmartPower™, Spectre Alert™, UltraBright™, and Voice Alert™ are trademarks of Cobra Electronics Corporation, USA.Opticom™ is a trademark of 3M Corporation. Instaclear®for Ford is a registered trademark of Ford Motor Company, Inc. Electriclear®for GM is a registered trademark of General MotorsCorporation. 20-20™ and Ultra-Lyte™ are trademarks of Laser Technology, Inc. ProLaser™ andProLaser III™ are trademarks of Kustom Signals, Inc. Bee III™ and Pop™ are a trademarks of MPH Industries. Spectre™ is a trademark of Stalcar. Interceptor VG-2™ is a trademark ofTechniSonic Industries LTD. Tomar®is a registered trademark of TOMAR Electronics, Inc.Warranty
Optional Accessories24 EnglishOptional Accessories •You can find quality Cobra products and accessories at your local Cobra dealer, or in the U.S.A., you can order directly from Cobra.Windshield Mounting BracketIncludes suction cupsItem # 545-139-N-001Straight 12V DC Power CordIncludes plug and fuseItem # 420-030-N-001Coiled 12V DC Power CordIncludes plug and fuseItem # 420-026-N-001Dual Port Power AdapterIncludes adjustable plug (up to 90˚) and fuse Item # CLP-2BCustomer Assistance

Navigation menu