Code Systems FRDPC2002 Car Alarm Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	172235
Application ID	YUs767Ck8jXnqsHBNk4R5g==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.13kB (289163 bits)
Date Submitted	2001-10-01 00:00:00
Date Available	2001-10-01 00:00:00
Creation Date	2001-09-03 15:34:54
Producing Software	Acrobat 4.0 Scan Plug-in for Windows
Document Lastmod	2001-09-03 15:43:14
Document Title	User Manual
Document Creator	Acrobat 4.0 Scan Plug-in for Windows

4 Using Your Remote Transmitter
Press to ARM the
Sammy System an
Lock; Doors i, W van
3 m turn: iinm min
Was“
Press TWICE to turn»
Rear Detroslér‘
titanic Alatm
Arming the Security System
To arm the system, exit the vehicle, close all doors, then press“ the
ARM button. The siren" will “chirp” twice’ and the parking lights will
flash twice, indicating the system is armed. The doors will also lock at
this time (if equipped and connected), The status indicator (red
warning light on the dash) will blink steadily, once per second.
Pre-arm Made
It the siren chirps and the parking lights flash only once, this indicates
that the vehicle courtesy light is on, or that an entrance is not closed
securely. Check to see that doors, hood, and trunk are properly
closed. Once all entrances are secured (and the courtesy light is off).
the system will chirp / flash again. The system is now lully armed.
(If the entrance is not secured within 4 minutes, the system will arm
and ignore the unsecured entrance until it is closed.)
Disc/Ming the Security System
To disarm the system, press the DISARM button. The siren will chirp
and the parking lights will llash once, and the doors will unlock,
The courtesy light will turn on for 1 minute, or until the vehicle is started
Attempted Intrusion Identification
It the siren chirps four times when disarming, this indicates that the
system was triggered in your absence. The status indicator will also
flash rapidly. Perlorm the following operation to determine the protected
zone that triggered the system:
Alter disarming, press the
emergency override button.
The siren will chirp to indicate 3 c in, Hood
the cause ol the alarm trigger: 4 chlrps Trunk/Optional Sensors
55 chi s I nition was tur ed on
~memo".itsmm,assassins“? 3’ 9 fl
tor isssim i mom; ‘press and hclfl' leietslople§lng aiming" i “ma.
4 chirp W—s‘“ Interior Theft Sensor
2 chirps Door
“ ‘siieii' dlsoleletslc'hevehicle ham 1 n is used asthe ahim soundingdevice,‘
- ii you have chosen IheSilenl Aiming Oplloluhe siiaii will iiai sound when aiiiiiiig oi dlSdelng untllthe
applopllale mum is present a second lime.
Using Your Remote Transmitter (co/rt.)
Disabling the 1715” Interior Theft Sensor
It may be necessary at times to disable the I'l‘-sTM Interior Theft Sensor,
especially when parking in areas (like parking garages) where
extreme vibration may cause false alarms. Press the ARM button and
then press the FIND/PANIC button within two seconds of pressing
ARM to disable the interior theft sensor. The siren will chirp three times
to indicate that the sensor is disabled. The sensor will become
enabled again the next time the system is armed normally.
Two-Stage Door Unlock
If this feature is enabled on your system, pressing DISAFtM one time
will unlock only the driver's door. Press DISARM again within 1 minute
to unlock all doors.
Activating the Trunk Release Feature
Press and hold TRUNK to open the vehicle trunk or hatch (if equipped
and connected). |r this button is used to operate another accessory
the accessory will stay active for as long as the button is held.
Turning on the Vehicle Headlights
Press and hold the ARM button to turn on the vehicle headlights.
(The alarm system will attempt to arm it not already armed, unless it is
in Valet mode.) The lights will stay on for 20 seconds, or until LIGHTS
is pressed again.
Using the Progressive Car Finder Feature
Press FIND on the remote control to locate your vehicle, The siren will
emit five short chirps at low volume. increasing in volume each ol
three times the button is pressed
Personal Protection Alarm (Panic)
Press and hold the PANIC button to activate the vehicle siren and
parking lights for 30 seconds. (If the vehicle horn is connected, the
horn will “pulse" for 30 seconds.) Press any remote control button to
turn oil the Panic alarm.
Remote Start /stop Feature
Press ARM, then press STAFIT within 2 seconds on the remote control.
If all safety parameters are correct, the engine will start within 5 seconds
(diesel engines will take longer.) Press and hold START again to turn
off the vehicle. (Turn to page 6 for more on remote start leatures.)
6 Using Your Remote Transmitter (cont)
Using Valet Mode
If the Passive Arming feature is enabled on your system, Valet mode
temporarily prevents the alarm system from arming automatically.
This is useful when fueling or sen/icing your vehicle.
To enter Valet Made:
With the vehicle ignition on, press the ARM button. The red dashboard
warning light (status indicator) will turn on for one second, then turn
off. This indicates that the system is in Valet mode. Once the ignition is
turned oif, the status indicator will emit a quick doubletiash pattern.
Note: In Valet mode, all keyless entry, convenience and remote start
features operate normally.
To exit Vale! Made:
With the vehicle ignition on, press the DISARM button. The red
dashboard warning light (status indicator) will turn on for one second,
then turn off. This indicates that the system has exited Valet mode.
Hlnt: To prevent your security system from automatically arming while
unloading or refueling your vehicle, without placing the system in
Valet mode, simply press the disarm button on your remote control
transmitter after turning the ignition key oll. Doing so places your
system into a temporary or onetime Valet mode. Next time you exit
your vehicle the system will arm in the normal manner,
Using Your Remote Starter
Starling Your Vehicle
The remote start function is activated by pressing the ARM button,
then pressing the START button on the remote control within 2
seconds. The system will check the vehicle to ensure that it is safe to
start, and if all safety parameters are correct, the engine will start
within 5 seconds (diesel engines will take longer.) Press and hold
START again to turn off the vehicle.
If your vehicle stalls or does not sled...
If the vehicle stalls or does not start, the 04500 will pause 5 seconds,
then try 3 more times to start the vehicle (a total of four attempts). The
system pauses 5 seconds between each start attempt. If the vehicle
does not start after the fourth attempt, the 04500 will abort the start
process.
Vour vehicle can be started by remote control whether the alarm is
armed or disarmed. When the alarm is armed, the impact sensor turns
off when the vehicle is started to prevent the engine vibration from
setting off the alarm.
Using Your Remote Starter (cont'd)
Remote Start Safety Features
For safety and security reasons. the 04500 will shut off the vehicle
during remote start it any of the following occur:
- The vehicle hood is opened
- The brake is pressed before the vehicle ignition is turned on
with the key
' The engine reaches 3 times its normal idle”
- The alarm is triggered
As a safety precaution, the vehicle will shut off if Iett unattended tor 12
or 24 minutes, depending on the time preset by your installer.
Entering the Vehicle While It is Running via Remote Start
|.Press DISAFlM to unlock the door(s) and turn off the alarm
system (if it is not already off).
2. Enter the vehicle. Do not press the brake pedal.
3, Insert the key into the ignition and turn to the ON position.
4 Press the brake pedal. The remote starter disengages and the
vehicle will operate normally.
Pre-Heeting or Pie-Cooling the Interior of the Vehicle
Before exiting the vehicle, set the temperature controls to the desired
setting and operation. After the 04500 starts the vehicle, the heater or
air-conditioning will activate and heat or cool the interior to your
setting.
Turning on the Hear- Window Defroster (if connected)
While the vehicle is running via remote start, press DEFRST on the
remote control. The vehicle defroster will activate and run tor 10
minutes or for your vehicle's preset time limit,
Using the "Quick-stop ”Feature
If you want to make a short stop and leave your vehicle running (to keep
the interior warm or cool, tor instance), the quick stop feature allows
you to do this while keeping your vehicle secure and your keys with you.
To engage quick stop:
1.3top the vehicle and place the transmission in PARK.
2.With your foot oil the brake pedal, press the ARM button, then
press the START button on the remote control within 2 seconds
The parking lights will turn on, indicating that the vehicle is now
running via remote start.
3. Remove the keys from the ignition and exit the vehicle Press
ARM to arm the alarm system if desired.
Note: Do not leave children or animals unattended in the vehicle
when using the quick stop feature,
Notice : The changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2001:09:03 15:43:14+08:00
Create Date                     : 2001:09:03 15:34:54+08:00
Creator                         : Acrobat 4.0 Scan Plug-in for Windows
Producer                        : Acrobat 4.0 Scan Plug-in for Windows
Page Count                      : 4

EXIF Metadata provided by EXIF.tools