Coleman 2000001643 Users Manual 4010004158 Legacy Tent
2000001643 to the manual 2008e047-ba54-45d2-a038-931c24303ef2
2015-02-04
: Coleman Coleman-2000001643-Users-Manual-365349 coleman-2000001643-users-manual-365349 coleman pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
LEGACY TENT TM MODEL 2000001643 Before you begin Fig. 2 Read all instructions before set up. • Select a level site clear of rocks, branches, and other hard or sharp objects, to install your tent. WARNING: Keep clear of overhead power lines. • Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather. • Secure with all stakes and guylines provided to prevent property damage or personal injury. • For best results in windy conditions, position narrow end of tent into the wind. • Enlist the help of at least one other person to assist you when it is time to assemble the tent. Door 2B Pole Descriptions Description Main Body Pole, black Side Body Pole, grey Rainfly Pole, black Vertical Door Pole, black, short w/rubber tips Door Pole, black, long w/rubber tips Qty. Pole Dia. Pole Repair Kit Pole Replacement Kit 2 2 1 11mm 9.5mm 11mm 501000539 501000540 501000539 501000549 501000548 501000549 1 6.3mm 501000543 501000545 1 6.3mm 501000543 501000545 STITCH LINE To Set Up Tent 1. Unfold tent and spread out on a clean, level surface with the door facing the desired direction. (Fig. 1) 2. Assemble all poles by interlocking the shock-corded, sections together. 3. Insert grey Side Body Poles through the grey trimmed sleeves on both sides of tent; then insert black Main Body Poles through black trimmed sleeves, in center of tent, forming a “X”. Make sure black Main Body Poles overlap the grey Side Body Poles. (Fig. 1) 2C Hinged, Rigid Door 1. Assemble Vertical Door Pole (shorter black pole with plastic tips); then insert through zippered vertical pole sleeve on hinged side of door. (Fig. 3) 2. Insert end of Vertical Door Pole into bottom hinge plate, apply pressure to form a slight bow, then insert other tip of pole into top hinge. Zip up vertical pole sleeve. (Fig. 4 & 5) 3. Assemble Door Pole (longer black pole with plastic cap tips); then insert into zippered pole sleeve at top of door. (Fig. 6) 4. Insert end of Door Pole into top hinge plate, apply pressure to form a bow, then insert other tip of pole into the bottom hinge. (Fig. 7) 5. Zip up pole sleeve to enclose Door Pole. (Fig. 8) Fig. 3 Sleeve with Grey Trim Fig. 4 Fig. 5 Vertical Pole Sleeve Door Hinge Fig. 7 Fig. 6 Sleeves with Black Trim 2A Fig. 1 Sleeve with Grey Trim Top Door Hinge Pole Sleeve Fig. 8 Door To Attach Rainfly Front of Tent Black, Shock-corded Main Body Poles Grey, Shock-corded Side Body Poles 1. Insert black Rainfly Pole with through sleeve in underside of Rainfly. (Fig. 9) 2. Drape Rainfly over tent with Rainfly Pole centered above front door & the dark blue vestibule flaps located in the front. (Fig 9) Fig. 9 4. Insert end of each black Main Body Poles & grey Side Body Poles into pins. (Fig. 2 & 2A) 5. Go to opposite end of each pole and gradually apply pressure to each forming arches. Insert the pin into each pole end at the sides and corners of tent. (Fig. 2 & 2A) 6. Attach frame clips along edges of tent to the black Main Body Poles & grey Side Body Poles. (Fig. 2B) 7. Stretch tent until taut, then secure metal loops located on both sides and web loops located at four corners of tent with stakes. (Fig. 2C) Rainfly Sleeve Rainfly Door (continued on other side) Black Rainfly Pole To Attach Rainfly (continued) To Store 3. Insert end of each black Rainfly Pole into pin on either side of front door. (Fig. 10 & 10A) 4. Go to opposite end of Rainfly Pole and gradually apply pres sure to form an arch. Insert the pin into pole end at other side of the door. (Fig. 10 & 10A) 5. Locate all hook & loop fasteners on underside of Rainfly and wrap around black and grey poles to secure. (Fig. 10B) 6. Stretch elastic straps and hook clip on each to the metal loops at the front and back of the tent. (Fig. 10C) 7. Extend out vestibule flaps and secure with metal stakes through the loops in the web straps (Fig. 10 & 5D) 8. Stretch guylines until taut, then secure with stakes. (Fig. 10 & 10E) 1. All poles and stakes must be placed in the storage bag to pre vent damage to the fabric items placed in the carry case. 2. Make sure tent is clean and dry before placing in carry case. 3. Remove rainfly, spread out on floor of tent, then unzip door & vents before taking tent down for storage. 4. Neatly fold tent to width of pole storage bag, place on tent, roll tightly, and place in carry case. 5. Store in a clean, dry area. 10B 10A 10C Things You Should Know: • Under certain conditions (cold weather, high humidity, etc.) condensation will form on the inside of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent. • Tree limbs, tree sap, bird droppings, or moisture steadily dripping off tree limbs can cause damage to the tent fabric and its coating resulting in leaks or loss of flame-resistant properties. • Never store tent, even for a short period of time, without drying it thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate storage bag. • Stakes should be removed by pulling on the stake itself. NEVER PULL ON THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. • Tent poles should not be left telescoped together during storage. • Do not leave your tent set-up for weeks at a time. Be aware that exposure to ultraviolet rays from the sun can seriously damage material and/or cause it to become discolored. WARNING: Keep all flame and heat sources away from this tent fabric. Fig. 10 Guylines 10E Electrical Cord Access 10D Fig. 16 1. Unzip the access panel in the lower left corner of tent and bring in an electrical cord. NOTE: Use only UL approved cords rated for outdoor usage. (Fig. 16) Cooler Access The smaller zippered opening at the side of tent is designed for added ventilation and easy access to your beverage cooler. Fig. 17 1. To use as a vent, unzip flap to expose screen. 2. To use as a cooler access, unzip other flap to make an avenue to bring beverages into tent. (Fig. 17) The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219 1-800-835-3278 • www.coleman.com MADE IN CHINA • PRINTED IN CHINA © 2008 The Coleman Company, Inc. Coleman®, , and are registered trademarks and LegacyTM is a trademark of The Coleman Company, Inc. 4010004158 (20081029)) STITCH LINE This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Trapped : False GTS PDFX Version : PDF/X-1:2001 GTS PDFX Conformance : PDF/X-1a:2001 Producer : Acrobat Distiller 7.0.5 for Macintosh Keywords : Manuals Modify Date : 2011:09:15 13:40:15-05:00 Creator Tool : QuarkXPress: pictwpstops filter 1.0 Create Date : 2008:11:04 10:00:25-06:00 Metadata Date : 2011:09:15 13:40:15-05:00 Format : application/pdf Creator : System Administrator Title : 4010004158-Legacy Tent Description : PDF Subject : Manuals Document ID : uuid:86d2c2ba-047f-4516-a39b-f98efa469c4f Instance ID : uuid:3515cc12-2ec5-49a4-8167-fb55d06cc6c8 Page Count : 2 Author : System AdministratorEXIF Metadata provided by EXIF.tools