Coleman 2300 511 Users Manual Hot Water On Demand Hose Adapter

2300-511 to the manual 99c7b10d-d89f-499a-955b-aa9a5d7b3868

: Coleman Coleman-2300-511-Users-Manual-365388 coleman-2300-511-users-manual-365388 coleman pdf

Open the PDF directly: View PDF .
Page Count: 4

The Water Hose Adapter connects a

standard water hose to

Hot Water on DemandTM.Once adapter

is in place and water is turned on at the

source, use Hot Water on DemandTM

to turn water on & off and to select

desired water temperature.

WATER HOSE

ADAPTER

Instructions for Use

Model 2300-511

Attach Water Hose Adapter to Hot

Water on DemandTM:

1. Remove water pump assembly:

a. Disconnect water pump electrical connection from

Hot Water on DemandTM (fig. 1).

b. Remove water

pump by releasing

the quick connector

(fig. 1). Electrical Connection

Quick Connector

fig. 1

Be sure Hot Water on DemandTM is turned off and no

water is running through unit. Operate unit from a

camp table or picnic table. Do not set it on ground to

use. (Water will drain when unit is off, preventing dam-

age in freezing temperatures.

Adapter Water

Inlet Fitting

Electrical

Connection

Quick Connector

Water Tubing

Clips

WATER HOSE ADAPTER

Parts Identifier

2. Connect Water Hose Adapter to Hot Water on

DemandTM:

a. Connect Water Hose Adapter electrical connec-

tion to Hot Water on DemandTM.

b. Connect Water Hose Adapter to Hot Water on

DemandTM by inserting Quick Connector.

c. Connect and tighten water hose to adapter water

inlet fitting.

d. Connect water hose to water source.

To Start Hot Water on DemandTM:

1. Turn on water at source (fig. 2).

2. Turn Hot Water on DemandTM Control Knob to

“COOL” until water

dispenses (fig. 3).

3. Turn Control Knob

to “OFF” (fig. 4).

4. To select desired

temperature setting,

turn Control Knob,

counterclockwise.

To Start Hot Water on DemandTM (continued):

fig. 2

fig. 3 fig. 4

To Remove from Hot Water on

DemandTM:

1. Disconnect Water Hose Adapter electrical con-

nection from Hot Water on DemandTM .

2. Disconnect adapter hose from Hot Water on

DemandTM by releasing the Quick Connector.

3. Reconnect Water Pump electrical connection

to Hot Water on DemandTM .

4. Reconnect Water Pump hose to Hot Water on

DemandTM by inserting the Quick Connector.

Attach Water Hose Adapter to

Hot Water on DemandTM (continued):

The Coleman Co., Inc. • 3600 N. Hydraulic • Wichita, KS 67219 U.S.A.

1-800-835-3278 • TDD: 316-832-8707

©2003 The Coleman Company, Inc. All Rights reserved.

Coleman® is a registered trademark of The Coleman Company, Inc.

For information regarding other

Hot Water on DemandTM accessories:

Visit us at

www.coleman.com

2300-052 (05/03)

Maintenance:

To Clean:

1. In a clean container mix one-gallon of water with 6 oz. of a calcium, lime, and rust remover solution

(available at hardware, general merchandise and food stores).

2. Disconnect water hose adapter from unit.

3. Unscrew water tubing from adapter body.

4. Detach clips from water tubing.

5. Submerge water tubing in cleaning solution. Allow to set five (5) minutes.

6. Run clean water through water tubing.

7. Air dry.

8. Reattach tubing to Water Hose Adapter and reattach clips to water tubing.