Coleman Elite Montana 8 Tent 2000004679 Users Manual

2000004679 to the manual c364a272-71c3-4b6a-8a17-84958bbab54a

: Coleman Coleman-Elite-Montana-8-Tent-2000004679-Users-Manual-365097 coleman-elite-montana-8-tent-2000004679-users-manual-365097 coleman pdf

Open the PDF directly: View PDF .
Page Count: 2

STITCH LINE

ELITE MONTANATM 8 TENT MODEL 2000001584

To Set Up Tent

1. Unfold tent and spread out on a clean, level surface with the door

facing the desired direction. (Fig. 1)

2. Assemble all poles by interlocking the shock-corded, sections

together.

3. Insert grey Side Body Poles through the grey trimmed sleeves on

both sides of tent; then insert black Main Body Poles through black

trimmed sleeves, in center of tent, forming a “X”. Make sure black

Main Body Poles overlap the grey Side Body Poles. (Fig. 1) To Attach Rainfly

1. Insert black Rainfly Pole with through sleeve in underside of

Rainfly. (Fig. 9)

2. Drape Rainfly over tent with Rainfly Pole centered above front door

& the dark blue vestibule flaps located in the front. (Fig 9)

(continued on other side)

Fig. 2

Door

2C

Fig. 1

Door

Front of Tent

Black, Shock-corded Main Body Poles

Grey, Shock-corded Side Body Poles

Sleeve with

Grey Trim

Sleeves with Black Trim

Sleeve with

Grey Trim

Fig. 9

Black Rainfly

Pole

Door

Rainfly Sleeve

Pole Descriptions

Pole Pole Pole

Description Qty. Dia. Repair Kit Replacement Kit

Main Body Pole, black 2 11mm 501000539 501000549

Side Body Pole, grey 2 9.5mm 501000540 501000548

Rainfly Pole, black 1 11mm 501000539 501000549

Vertical Door Pole, black,

short w/rubber tips 1 6.3mm 501000543 501000545

Door Pole, black,

long w/rubber tips 1 6.3mm 501000543 501000545

Before you begin

Read all instructions before set up.

• Select a level site clear of rocks, branches, and other hard or sharp

objects, to install your tent.

WARNING: Keep clear of overhead power lines.

• Do not set up your tent under trees because of potential lightning

strikes or falling tree limbs in inclement weather.

• Secure with all stakes and guylines provided to prevent property

damage or personal injury.

• For best results in windy conditions, position narrow end of tent into

the wind.

• Enlist the help of at least one other person to assist you when it is

time to assemble the tent.

Self-Rolling Window Spring Descriptions

Color Code Description Qty. Length Replacement Part No.

Red 2 360mm 5010000624

Yellow 1 550mm 5010000626

CAUTION: “Springs” may have sharp edges. Handle with care to avoid

injury. Keep out of reach of children.

4. Insert end of each black Main Body Poles & grey Side Body Poles

into pins. (Fig. 2 & 2A)

5. Go to opposite end of each pole and gradually apply pressure to

each forming arches. Insert the pin into each pole end at the sides

and corners of tent. (Fig. 2 & 2A)

6. Attach frame clips along edges of tent to the black Main Body Poles

& grey Side Body Poles. (Fig. 2B)

7. Stretch tent until taut, then secure metal loops located on both

sides and web loops located at four corners of tent with stakes.

(Fig. 2C)

Hinged, Rigid Door

1. Assemble Vertical Door Pole (shorter black pole with plastic tips);

then insert through zippered vertical pole sleeve on hinged side of

door. (Fig. 3)

2. Insert end of Vertical Door Pole into bottom hinge plate, apply

pressure to form a slight bow, then insert other tip of pole into top

hinge. Zip up vertical pole sleeve. (Fig. 4 & 5)

3. Assemble Door Pole (longer black pole with plastic cap tips); then

insert into zippered pole sleeve at top of door. (Fig. 6)

4. Insert end of Door Pole into top hinge plate, apply pressure to form

a bow, then insert other tip of pole into the bottom hinge. (Fig. 7)

5. Zip up pole sleeve to enclose Door Pole. (Fig. 8)

Fig. 3 Fig. 4 Fig. 5

Fig. 6 Fig. 7

Fig. 8

Vertical Pole

Sleeve

Door Hinge

Pole

Sleeve

Top

Door

Hinge Pole

Sleeve

Top

Door

Hinge

Rainfly

2B 2A

STITCH LINE

To Attach Rainfly continued

3. Insert end of each black Rainfly Pole into pin on either side of front

door. (Fig. 10 & 10A)

4. Go to opposite end of Rainfly Pole and gradually apply pressure to

form an arch. Insert the pin into pole end at other side of the door.

(Fig. 10 & 10A)

5. Locate all hook & loop fasteners on underside of Rainfly and wrap

around black and grey poles to secure. (Fig. 10B)

6. Stretch elastic straps and hook clip on each to the metal loops at

the front and back of the tent. (Fig. 10C)

7. Extend out vestibule flaps and secure with metal stakes through the

loops in the web straps (Fig. 10 & 5D)

8. Stretch guylines until taut, then secure with stakes. (Fig. 10 & 10E)

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219

1-800-835-3278 • www.coleman.com

MADE IN CHINA • PRINTED IN CHINA

© 2008 The Coleman Company, Inc.

Coleman®, , and are registered trademarks and MontanaTM is a trademark of

The Coleman Company, Inc.

4010003991 (20080928)

Self-rolling Windows

CAUTION: “Springs” may have sharp edges. Handle with care to avoid

injury. Keep out of reach of children.

NOTE: Carefully unroll metal “springs” stored in bag with stakes. The

color marking on each “spring” should match the color of the fabric

“flag” sewn to the window or door sleeve opening. (Fig. 11)

1. Locate sleeve(s) in window panel, open hook & loop fastener; then

insert “spring(s)” with matching color marking. (Fig. 11 & 12)

NOTE: When inserting into the sleeve(s), the

color marking on the “spring(s)” should always

face the operator.

2. Close hook & loop fastener to secure.

3. Before unzipping and opening the window,

push in at top to engage “spring(s)” to activate

the self-rolling feature. (Fig. 13)

4. Unzip to allow the window panel to roll down

automatically; zip back to close window panel.

(Fig. 14 & 15)

NOTE: Repeat steps above for inserting the color

matching “spring(s)” into sleeve(s) for the rest of

the windows.

Fig. 11

Sleeve

Color “Flag”

Door

Window

Panel

Window Panel

Push in at top

to engage

“spring(s)”

Color

Dot

Fig. 13

Fig. 12

Sleeves

Fig. 14

Fig. 15

Color

“Flag”

Tent Lighting System

Your tent comes pre-wired with the Coleman®Tent

Lighting System. See manual that came with the light

and carefully read all instructions before use then save

for future reference.

Things You Should Know:

• Under certain conditions (cold weather, high humidity, etc.) condensa-

tion will form on the inside of your tent. Condensation is caused by water

vapor from your breath, perspiration, or any wet clothing inside the tent.

It is NOT LEAKAGE through the shelter fabric. It can be minimized by

removing wet clothing from your shelter and by providing good ventila-

tion through the tent.

• Tree limbs, tree sap, bird droppings, or moisture steadily dripping off

tree limbs can cause damage to the tent fabric and its coating resulting

in leaks or loss of flame-resistant properties.

• Never store tent, even for a short period of time, without drying it

thoroughly and brushing off caked dirt. Do not pack stakes or poles

inside your tent. Use a separate storage bag.

• Stakes should be removed by pulling on the stake itself. NEVER PULL ON

THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY

DAMAGE OR PERSONAL INJURY.

• Tent poles should not be left telescoped together during storage.

• Do not leave your tent set-up for weeks at a time. Be aware that exposure

to ultraviolet rays from the sun can seriously damage material and/or

cause it to become discolored.

WARNING: Keep all flame and heat sources away

from this shelter fabric.

This shelter meets the flammability requirements of CPAI-84. The

fabric may burn if left in continuous contact with any flame source.

The application of any foreign substance to the tent fabric may

render the flame-resistant properties ineffective.

Self-rolling Windows continued

CAUTION: All “springs” must be removed from sleeves before tearing

down tent to avoid damage to the tent fabric or part. To avoid injury,

carefully roll up “springs”. Keep out of reach of children. Store rolled

“springs” in bag with stakes.

Cooler Access

The smaller zippered opening at the side of tent is

designed for added ventilation and easy access to

your beverage cooler.

1. To use as a vent, unzip flap to expose screen.

2. To use as a cooler access, unzip other flap to

make an avenue to bring beverages into tent. (Fig. 17)

To Store

1. All “springs” must be rolled up and placed in bag with stakes.

2. All poles and stakes must be placed in the storage bag to prevent

damage to the fabric items placed in the carry case.

3. Make sure tent is clean and dry before placing in carry case.

4. Remove rainfly, spread out on floor of tent, then unzip door & vents

before taking tent down for storage.

5. Neatly fold tent to width of pole storage bag, place on tent, roll

tightly, and place in carry case.

5. Store in a clean, dry area.

Electrical Cord Access

1. Unzip the access panel in the lower

left corner of tent and bring in an

electrical cord.

NOTE: Use only UL approved cords

rated for outdoor usage. (Fig. 16)

Fig. 17

Fig. 16

Fig. 10

10A10B

10C

10E 10D

Guylines