Colorado vNet APEXLT 802.15.4 Transceiver Module User Manual APEX LT Manual Colorado vNet

Download:
Mirror Download [FCC.gov]
Document ID	877568
Application ID	tdqxCeyRggHXcFL+Vx1/4g==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.48kB (81027 bits)
Date Submitted	2007-12-10 00:00:00
Date Available	2007-12-10 00:00:00
Creation Date	2007-11-29 16:27:33
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2007-11-30 07:43:26
Document Title	Microsoft Word - APEX LT Manual Colorado vNet.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ericr

COLORADO vNET APEX LT PRODUCT SUMMARY
Product Description
The Colorado vNet APEX LT module is a 2.4 GHz transceiver for integration in Colorado
vNet’s proprietary home automation products. The module is based on the Ember
EM260 network processor providing an IEEE 802.15.4 radio transceiver with a SPI base
interface. The SPI interface gives the flexibility to choose the external microprocessor to
best fit the application.
Key Features
•
•
•
•
•
•
•
•
•
•
•
100 mW output power
Integrated antenna
Supports MHF1 connector for external antenna
16 RF channels (Channel 16 at a reduced power level)
Output power is software controlled
AES-128 encryption
Constant RF output power over operating voltage range of 2.1 – 3.6V
Integrated IEEE 802.15.4 PHY and MAC
Dedicated network processor
SPI-slave or UART interface to application microprocessor
Handles all data processing and timing intensive tasks of ZigBee protocol
Specifications
Operating voltage range:
RF Frequency range:
RF Data rate:
Nominal output power:
Transmitter current:
Receive current:
Error Vector Magnitude:
Receiver Sensitivity:
2.1 – 3.6 V
2400 – 2483.5 MHz
250 kbps
100 mW (20 dBm)
170 mA
37 mA
15% typical
-96 dBm (1% PER)
I/O Summary
•
•
•
Connection to the API is made over SPI to allow application development on host
microprocessor.
Two additional signals (nHOST_INT and nWAKE) provided for handshaking.
Module is a slave device only. All transactions are initiated by the host.
Page 1 of 3
Colorado vNet
29 November 2007
Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC Interference Statement (Part 15.105 (b))
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure (OET Bulletin 65)
To comply with FCC’s RF exposure limits for general population / uncontrolled exposure,
the antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
Industry Canada Statement per Section 4.0 of RSP-100
The term "IC:" before the certification / registration number only signifies that the
Industry Canada technical specifications were met.
Section 7.1.5 of RSS-GEN
Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received,
including interference that may cause undesired operation.
Page 2 of 3
Colorado vNet
29 November 2007
OEM Responsibility to the FCC Rules and Regulations
The Apex LT Module has been certified per FCC Part 15 rules for integration into
Colorado vNet products without further testing or certification. To fulfill the FCC
certification requirements Colorado vNet must ensure that the information provided on
the Apex LT Label is placed on the outside of the final product.
The Apex LT Module is labeled with its own FCC ID Number. If the FCC ID is not visible
when the module is installed inside another device, then the outside of the device into
which the module is installed must also display a label referring to the enclosed module.
This exterior label can use wording such as the following:
“Contains Transmitter Module FCC ID: VOX-APEXLT”
or
“Contains FCC ID: VOX-APEXLT”
Colorado vNet must only use the approved antenna, which has been certified with this
module.
Colorado vNet must test their final product configuration to comply with Unintentional
Radiator Limits before declaring FCC compliance per Part 15 of the FCC Rules.
Page 3 of 3
Colorado vNet
29 November 2007

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 6.0 (Windows)
Modify Date                     : 2007:11:30 07:43:26-06:00
Create Date                     : 2007:11:29 16:27:33-07:00
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2007:11:30 07:43:26-06:00
Document ID                     : uuid:a0c94c34-1c07-4451-98da-3e4a579af63d
Instance ID                     : uuid:da827031-0e6a-41d1-93dd-9ebcc384569f
Format                          : application/pdf
Title                           : Microsoft Word - APEX LT Manual Colorado vNet.doc
Creator                         : ericr
Page Count                      : 3
Author                          : ericr

EXIF Metadata provided by EXIF.tools