Comba Telecom RA-5700-R Tri-band Distributed Antenna System User Manual REV2
Comba Telecom Ltd. Tri-band Distributed Antenna System REV2
User manual REV2
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1460049 |
| Application ID | ClqtINysFRShpRzZuQRGGQ== |
| Document Description | User manual REV2 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 302.1kB (3776273 bits) |
| Date Submitted | 2011-05-06 00:00:00 |
| Date Available | 2011-05-10 00:00:00 |
| Creation Date | 2011-04-06 09:57:21 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2011-04-06 09:57:21 |
| Document Title | User manual REV2 |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | D Shiu |
USER MANUAL FOR RA-5700
RA-5700
TRI-BAND DISTRIBUTED ANTENNA
SYSTEM
USER MANUAL
The information contained herein is the
responsibility of and is approved by the
following, to whom all enquiries should
be directed in the first instance:
Comba Telecom Ltd.
This is an unpublished work the copyright in which vests in Comba International ("Comba"). All rights reserved.
The information contained herein is confidential and the property of Comba and is supplied without liability for errors or
omissions. No part may be reproduced, disclosed or used except as authorised by contract or other written permission. The
copyright and the foregoing restriction on reproduction and use extend to all media in which the information may be embodied.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 1
USER MANUAL FOR RA-5700
0.2 CONTENTS
Section
Page
0.2
0.3
0.4
0.5
0.6
0.7
CONTENTS ........................................................................................................................... 2
INDEX TO FIGURES AND TABLES ..................................................................................... 4
HISTORY ............................................................................................................................... 6
GLOSSARY OF TERMS ....................................................................................................... 7
FCC SAFETY COMPLIANCE................................................................................................ 8
SAFETY NOTICES AND ADMONISHMENTS .................................................................... 10
GENERAL INFORMATION ................................................................................................. 11
2.1
2.2
2.2.1
2.3
2.4
2.5
EQUIPMENT DESCRIPTION .............................................................................................. 13
SYSTEM DIAGRAM ............................................................................................................ 13
TYPICAL APPLICATION ..................................................................................................... 14
SINGLE FIBER CONFIGURATION ..................................................................................... 14
EQUIPMENT LAYOUT ........................................................................................................ 15
EQUIPMENT CONSTITUTION ........................................................................................... 17
KIT OF PARTS .................................................................................................................... 18
3.1
3.2
3.2.1
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.3.6
3.3.7
3.3.8
3.4
3.4.1
3.4.2
3.5
3.5.1
3.5.2
3.5.3
3.5.4
3.5.5
3.5.6
INSTALLATION ................................................................................................................... 19
WARNINGS AND ALERTS ................................................................................................. 19
SITE PLANNING CONSIDERATIONS ................................................................................ 20
SYSTEM INSTALLATION CHECKLIST .............................................................................. 21
INSTALLATION PROCEDURES ......................................................................................... 22
GOODS INWARDS INSPECTION ...................................................................................... 22
TOOLS................................................................................................................................. 22
PREPARATION ................................................................................................................... 22
CABINET MOUNTING OF MU ............................................................................................ 23
RU MOUNTING RACK DIMENSION .................................................................................. 23
WALL MOUNTING OF RU .................................................................................................. 24
POLE MOUNTING OF RU .................................................................................................. 25
DRIP-LOOP ......................................................................................................................... 25
EQUIPMENT CONNECTORS ............................................................................................. 26
MU CONNECTORS............................................................................................................. 26
RU CONNECTORS ............................................................................................................. 27
EQUIPMENT CONNECTION .............................................................................................. 28
GROUNDING CONNECTION ............................................................................................. 28
LI-ION BATTERY CONNECTION ....................................................................................... 28
OPTICAL CONNECTION .................................................................................................... 28
EXTERNAL ALARM CONNECTION ................................................................................... 30
BTS ALARM CONNECTION ............................................................................................... 31
CONNECT TO PC ............................................................................................................... 32
4.1
4.2
4.3
4.3.1
4.3.2
4.4
4.4.1
COMMISSIONING ............................................................................................................... 33
PRE-COMMISSIONING TASKS ......................................................................................... 33
MU/RU RESET TIME DURATION ...................................................................................... 33
LED INDICATORS............................................................................................................... 34
MU LED INDICATORS ........................................................................................................ 34
RU LED INDICATORS ........................................................................................................ 34
WEB OMT ........................................................................................................................... 35
CONNECTION FROM PC TO EQUIPMENT ...................................................................... 35
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 2
USER MANUAL FOR RA-5700
4.4.2
4.4.3
4.4.4
4.4.5
4.4.6
4.4.7
4.4.8
4.4.9
OMT CONFIGURATION ..................................................................................................... 36
SYSTEM INFORAMTION .................................................................................................... 36
RF INFORMATION .............................................................................................................. 39
ALARM INFORMATION ...................................................................................................... 42
PROPERTIES INFORMATION ........................................................................................... 44
USER MANAGEMENT ........................................................................................................ 46
HELP ................................................................................................................................... 47
CHANGE PASSWORD ....................................................................................................... 48
TROUBLESHOOTING ........................................................................................................ 49
MAINTENANCE................................................................................................................... 50
7.1
7.1.1
7.1.2
7.1.3
7.1.4
7.1.5
7.1.6
7.1.7
7.1.8
7.2
7.3
7.4
7.5
APPENDICES ...................................................................................................................... 51
APPENDIX A: BAND SELECTIVE UNIT USER MANUAL .................................................. 51
BS-8132 BSU (BAND SELECTIVE UNIT) ........................................................................... 51
BS-1933 BSU ...................................................................................................................... 52
BS-8132&BS-1933 BSU LAYOUT ....................................................................................... 53
BS-8132&BS-1933 KOP ...................................................................................................... 53
BSU OMT ........................................................................................................................... 54
BS-1933 OMT ..................................................................................................................... 56
BS-8132 OMT ...................................................................................................................... 59
BS-8132&BS-1933 BSU CONNECTORS ........................................................................... 62
APPENDIX B: TOOLS FOR INSTALLATION AND MAINTENANCE .................................. 63
APPENDIX C: OVERDRIVE PROTECTION PROCEDURE ............................................... 64
APPENDIX D: SERVICING POLICY AND RETURN OF EQUIPMENT .............................. 65
APPENDIX E: RMA (RETURN MATERIAL AUTHORIZATION) FORM ............................. 66
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 3
USER MANUAL FOR RA-5700
0.3 INDEX TO FIGURES AND TABLES
Figure 1: View of MU Fully Equipped Shelf ........................................................................................................... 11
Figure 2: Front, Side and Bottom Views of RU Enclosure .................................................................................. 12
Figure 3: System Diagram ....................................................................................................................................... 13
Figure 4: Application of One MU with One RU through One Optical Module with WDM ................................ 14
Figure 5: Application of One MU with Four RUs through four Optical Modules with WDM ............................ 15
Figure 6: MU Equipment Layout ............................................................................................................................. 15
Figure 8: Cabinet Mounting of 19” Shelf ................................................................................................................ 23
Figure 9: RU Mounting Rack Dimension ............................................................................................................... 24
Figure 10: RU Wall Mounting .................................................................................................................................. 24
Figure 11: Pole Mounting of RU .............................................................................................................................. 25
Figure 12: MU Front Panel Connectors ................................................................................................................. 26
Figure 13: MU Back Panel Connectors.................................................................................................................. 26
Figure 14: RU Connectors ....................................................................................................................................... 27
Figure 15: Optical Connection ................................................................................................................................. 29
Figure 16: Pins Allocation for “EXT_ALM” Port for MU ....................................................................................... 30
Figure 17: Pins Allocation for “EXT_ALM” Port for RU ........................................................................................ 30
Figure 18: Pins Allocation for “BTS_ALM” Port .................................................................................................... 31
Figure 19: Web OMT Access .................................................................................................................................. 35
Figure 20: Log in ....................................................................................................................................................... 36
Figure 21: System Information ................................................................................................................................ 37
Figure 22: Firmware Update .................................................................................................................................... 37
Figure 23: Maintenance............................................................................................................................................ 38
Figure 24: Data Import ............................................................................................................................................. 38
Figure 25: Data Export ............................................................................................................................................. 39
Figure 26: Switch....................................................................................................................................................... 39
Figure 27: Alarm Threshold ..................................................................................................................................... 40
Figure 28: Temperature ........................................................................................................................................... 40
Figure 29: ATT........................................................................................................................................................... 41
Figure 30: Power ....................................................................................................................................................... 41
Figure 31: Gain .......................................................................................................................................................... 42
Figure 33: Master Alarm........................................................................................................................................... 43
Figure 34: Channel Alarm ........................................................................................................................................ 43
Figure 35: External Alarm ........................................................................................................................................ 43
Figure 36: Equipment ID .......................................................................................................................................... 44
Figure 37: Equipment Info. ...................................................................................................................................... 44
Figure 38: Site Location ........................................................................................................................................... 45
Figure 39: System Clock .......................................................................................................................................... 45
Figure 40: Comm. Config......................................................................................................................................... 45
Figure 41: Firmware Information ............................................................................................................................. 46
Figure 42: User Information ..................................................................................................................................... 46
Figure 43: Set Session Time ................................................................................................................................... 47
Figure 44: Help .......................................................................................................................................................... 47
Figure 45: About ........................................................................................................................................................ 47
Figure 46: Password Configuration ........................................................................................................................ 48
Figure 47: Change Password .................................................................................................................................. 48
Figure 48: BSU Layout ............................................................................................................................................. 53
Figure 49: Connection Type .................................................................................................................................... 54
Figure 50: Serial Port Configuration ....................................................................................................................... 55
Figure 52: System Information ................................................................................................................................ 56
Figure 53: Auto-Read ............................................................................................................................................... 56
Figure 54: Switch....................................................................................................................................................... 57
Figure 55: Channel NO. ........................................................................................................................................... 57
Figure 56: Channel Alarm ........................................................................................................................................ 58
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 4
USER MANUAL FOR RA-5700
Figure 57: Equipment ID .......................................................................................................................................... 58
Figure 58: System Information ................................................................................................................................ 59
Figure 59: Auto-Read ............................................................................................................................................... 60
Figure 60: Switch....................................................................................................................................................... 60
Figure 61: Channel NO. ........................................................................................................................................... 61
Figure 62:Channel Alarm ......................................................................................................................................... 61
Figure 63: Equipment ID .......................................................................................................................................... 61
Figure 64: BSU Connectors ..................................................................................................................................... 62
Figure 65: BSU Connection Overview ................................................................................................................... 63
Table 1: MU Constitution.......................................................................................................................................... 17
Table 2: RU Constitution .......................................................................................................................................... 17
Table 3: MU KOP ...................................................................................................................................................... 18
Table 4: RU KOP ...................................................................................................................................................... 18
Table 5: MU Front Panel Connections ................................................................................................................... 26
Table 6: MU Back Panel Connections ................................................................................................................... 26
Table 7: RU Connections ......................................................................................................................................... 27
Table 8: Pin Definition of “EXT_ALM” Port for MU ............................................................................................... 30
Table 9: Pin Definition of “EXT_ALM” Port for RU ............................................................................................... 30
Table 10: MU LED Indicators .................................................................................................................................. 34
Table 11: RU LED Indicators ................................................................................................................................... 34
Table 12: IP Setting Quick Look-up Table............................................................................................................. 36
Table 13: Equipment ID ........................................................................................................................................... 44
Table 14: Alarms Diagnosis..................................................................................................................................... 50
Table 15: Bandwidth and Channel No. .................................................................................................................. 51
Table 16: BS-1933 KOP........................................................................................................................................... 53
Table 17: BS-8132 KOP........................................................................................................................................... 54
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 5
USER MANUAL FOR RA-5700
0.4HISTORY
Change No.
ENU
Details Of Change
1-0-0
1-1-0
1-1-1
This user manual first created on 28May2010 which referred to its
Chinese manual RA-5700-1001YH released in May 2010.
Updated Web OMT, added BUS layout in this document in Oct
2010.
Update the user manual based on the requirement in Dec 2010.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 6
USER MANUAL FOR RA-5700
0.5 GLOSSARY OF TERMS
ALC
Automatic Level Control
ATT
Attenuation
BS
Base Station
BTS
Base Transceiver Station
dB
Decibel
dBm
Decibels relative to 1 milliwatt
DL
Downlink
DPX
Duplexer
DT
Donor Terminal
EEPROM
Electrically Erasable Programmable Read Only Memory
E/O,O/E
Electrical/Optical, Optical/Electrical
Hz
Hertz
ID
Identification
LNA
Low Noise Amplifier
MCU
Main Control Unit
MHz
Megahertz
MT
Mobile Terminal
MTBF
Mean Time Between Failures
NC
Normally Closed
NF
Noise Figure
NO
Normally Open
OMC
Operation & Maintenance Center
OMT
Operation & Maintenance Terminal
OP
Optical Fiber
PA
Power Amplifier
PLL
Phase Locked Loop
POI
Point of Interconnects
PSU
Power Supply Unit
RF
Radio Frequency
RX
Receive
SMA
Sub-Miniature “A” Connector
TX/RX
Transmit/Receive
UL
Uplink
VAC
Volts Alternating Current
VSWR
Voltage Standing Wave Ratio
WCDMA
Wideband Code Division Multiple Access
WDM
Wavelength Division Multiplexer
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 7
USER MANUAL FOR RA-5700
0.6 FCC SAFETY COMPLIANCE
Comaba Tri-band Distributed Antenna System (DAS) has been tested and complies with the FCC rules.
FCC ID: PX8RA-5700-R
Environmental evaluation and exposure limit according to FCC CFR 47part 1, §1.1307, §1.1310
The below table shows the RF exposure for fixed repeater
Antenna Type
IXD120V06K02(17102500MHz)
IXD120V06N03(806960/17102500MHz)
IXD360V03K02(17102500MHz)
IXD360V03N02(806960/17102500MHz)
IXD360V03N03(806960/17102500MHz)
IXD360V03N033(698896/17102700MHz)
IXD360V03N052(806960/17102700MHz)
IXD360V03N054(698960/17102700MHz)
RA-5700 QI
ENU Status : 1-1-2
Safe
Distance
(cm)
Antenna
EIRP(mW)
Antenna
Input
Power(dBm)
Antenna
Gain(dBi)
Requirement
(mW/cm2)
Frequency(
MHz)
17.80
3981.07
30
1.00
1960
23.22
3981.07
30
0.59
881
17.80
3981.07
30
1.00
1960
11.36
1621.81
30
2.1
1.00
1960
18.45
2511.89
30
0.59
881
14.14
2511.89
30
1.00
1960
20.00
2951.21
30
4.7
0.59
881
15.32
2951.21
30
4.7
1.00
1960
25.39
3981.07
30
0.49
737
25.15
3981.07
30
0.50
751
23.22
3981.07
30
0.59
881
17.80
3981.07
30
1.00
1960
20.00
2951.21
30
4.7
0.59
881
15.32
2951.21
30
4.7
1.00
1960
20.17
2511.89
30
0.49
737
19.98
2511.89
30
0.50
751
18.45
2511.89
30
0.59
881
14.14
2511.89
30
1.00
1960
Copyright - refer to title page
Page 8
USER MANUAL FOR RA-5700
Antenna
Type
IXD360V03N06(806960/17102500MHz)
10
IWH090V08N02(806960/17102700MHz)
11
IWH120V06N01(806960/17102500MHz)
Safe
Distance
(cm)
Antenna
EIRP(mW)
Antenna
Input
Power(dBm)
Antenna
Gain(dBi)
Requirement
(mW/cm2)
Frequency(
MHz)
20.00
2951.21
30
4.7
0.59
881
15.32
2951.21
30
4.7
1.00
1900
29.45
6309.57
30
0.58
869
22.41
6309.57
30
1.00
1900
23.22
3981.07
30
0.59
881
17.80
3981.07
30
1.00
1900
*Antenna type: comtact Comba US office if any questions regarding out antenna product and service.
FCC ID: PX8RA-5700-D
PX8RA-5700-D is connected to BTS output via RF cable and coupler, the RF output power is less than 1
mW and far below the BTS output power, so the safety expossure distance is short than BTS safety
exposure distance, no additional notice for safety exposure distance.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 9
USER MANUAL FOR RA-5700
0.7 SAFETY NOTICES AND ADMONISHMENTS
This document contains safety notices in accordance with appropriate standards. In the interests of
conformity with the territory standards for the country concerned, the equivalent territorial admonishments
are also shown.
Any installation, adjustment, maintenance and repair of the equipment must only be carried out by trained,
authorized personnel. At all times, personnel must comply with any safety notices and instructions.
Specific hazards are indicated by symbol labels on or near the affected parts of the equipment. The labels
conform to international standards, are triangular in shape, and are coloured black on a yellow
background. An informative text label may accompany the symbol label.
Hazard labeling is supplemented by safety notices in the appropriate equipment manual. These notices
contain additional information on the nature of the hazard and may also specify precautions.
Warning:
These draw the attention of personnel to hazards that may cause death or injury to the operator or others.
Examples of use are cases of high voltage, laser emission, toxic substances, point of high temperature,
etc.
Alert:
These draw the attention of personnel to hazards that may cause damage to the equipment. An example
of use is the case of static electricity hazard.
Caution notices may also be used in the handbook to draw attention to matters that do not constitute a risk
of causing damage to the equipment but where there is a possibility of seriously impairing its performance,
e.g. by mishandling or gross maladjustment. Warnings and Cautions within the main text do not
incorporate labels and may be in shortened form.
End of Section
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 10
USER MANUAL FOR RA-5700
1 GENERAL INFORMATION
The RA-5700 Tri-Band Distributed Antenna System (hereinafter called “RA-5700”) is designed for working
on 700MHz, 850MHz and 1900MHz networks. It provides flexible and scalable solution of multi-band,
multi-operator coverage extension applications.It is the ideal solution to both indoor and outdoor as well.
RA-5700 consists of Master Unit (MU) RA-5700-D and Remote Unit (RU) RA-5700-R.
The low signal transmission loss of optical fiber is applicable for long distance transmission. RA-5700 can
support the optical transmission of up to 5dB signal transmission loss. It can extend BTS coverage and
eliminate blindspot, shadow area and weak-signal area to improve call quality.
Main feature:
High output power with high linearity, which supports multiple carrier operation and ensures the signal
source is of good quality.
Optical fiber transmission with long distance transition at the most path loss of 5dB.
Local Operation and Maintenance Terminal (OMT): operating status and parameters can be set or
monitored by OMT PC locally. And the point-to-point setting and inquiry between MU and RU is
realizable through the integrated wireline/wireless modem, which makes it convenient for on-site
configuration.
Operation Maintenance Center (OMC): system working parameters and communication configuration
can be set or inquired remotely through the integrated Ethernet adaptor. If alarm is generated, the
equipment will dial up to OMC automatically in the mode of GPRS.
Build-in Li-ion battery ensures that alarm information can automatically report to OMC in case of
equipment power failure.
RU is designed for all-weather outdoor operation - waterproof, damp-proof and omni-sealed.
17.2"
The figures below show the equipment enclosure layout of RA-5700 MU and RU:
5.2"
19"
Figure 1: View of MU Fully Equipped Shelf
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 11
20"
USER MANUAL FOR RA-5700
5"
10"
Figure 2: Front, Side and Bottom Views of RU Enclosure
End of Section
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 12
USER MANUAL FOR RA-5700
2 EQUIPMENT DESCRIPTION
2.1
SYSTEM DIAGRAM
MU
Optical Fiber
Optical Fiber
RU
RU
RU
Cable
Distribution
Cable
Distribution
Cable
Distribution
RU
Cable
Distribution
Figure 3: System Diagram
On the DL, combined signals as 700MHz, 850MHz and 1900MHz from the BTSs converted into optical
signals after amplification in the MU.Then the optical signals are transmitted to the RU via optical fiber.
The Optical TX/RX Module of RU converts the DL optical signals into RF signals. After amplification, the
signals are transmitted at the MT port to the service antenna.
On the UL, the signals transmitted by the mobile are converted into optical signals, and then via the UL
optical fiber. The signals are transmitted to MU, which then converts the optical signals back to RF
signals.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 13
USER MANUAL FOR RA-5700
2.2
TYPICAL APPLICATION
2.2.1 SINGLE FIBER CONFIGURATION
For equipments with WDM Unit, the single fiber configuration is applicable. Through using WDM
technique, one fiber is shared between optical signals.
Refer to the following two applications of single fiber configuration:
2.2.1.1 Typical Application of Single Fiber Configuration
Shown below is a typical application showing the ability to interwork RA-5700.
Tx/Rx
Coupler
ANT
Tx/Rx
BTS
MU
WDM
OP UL_DL
OP UL_DL WDM
1310nm/1550nm
RU
MT
Figure 4: Application of One MU with One RU through One Optical Module with WDM
2.2.1.2 Extension Application of Single Fiber Configuration
A fully equipped MU can host up to four RU (s) through optical module. This can be achieved by
accommodating four Optical Modules with WDM. Refer to the figure below:
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 14
USER MANUAL FOR RA-5700
ANT
Tx/Rx
ANT
OP UL_DL
1310nm/1550nm
WDM
WDM
OP UL_DL
1310nm/1550nm
WDM
WDM
OP UL_DL
1310nm/1550nm
WDM
RU
WDM
OP UL_DL
1310nm/1550nm
WDM
RU
Coupler
WDM
Tx/Rx
MT
RU
ANT
MT
RU
ANT
MU
BTS
MT
MT
Figure 5: Application of One MU with Four RUs through four Optical Modules with WDM
2.3
EQUIPMENT LAYOUT
The MU RA-5700-D is constructed into a 19” shelf. It is connected via the connectors located on the front
panel. The RU RA-5700-R is designed for all cables entries from the bottom of the enclosure.
Duplexer 1
Optical TX/RX
Module 4
Optical TX/RX
Module 3
Optical TX/RX
Module 2
DL Adaptor
Module
Li-ion Battery
Distribution Board
PSU
UL Adaptor
Module
Optical TX/RX
Module 1
The internal layout for the MU is shown below:
Duplexer 2
Duplexer 3
Duplexer 4
MCU
LED Indicator Board
MODEM
Figure 6: MU Equipment Layout
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 15
USER MANUAL FOR RA-5700
The internal layout for the RU is shown below:
DL PA
Integrated
RF Module
PSU
Li-ion
Battery
MCU
1900/850
Dualband
Combiner
700MHz Duplexer
Surge
Arrestor
Figure 7: RU Equipment Layout
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 16
USER MANUAL FOR RA-5700
2.4
EQUIPMENT CONSTITUTION
RA-5700 consists of MU and RU that consists of the modules described below:
The MU consists of:
Identifier
Functional Description
Supports tri-band UL/DLRF Module, it splits and
UL/DL Adaptor Module
combines UL/DL signal to complete filter, gain
control and power control.
Duplexer
Completes signal conversion.
Completes optical signal and RF signal
Optical TX/RX Module
conversion.
Is used to control and monitor the operation
Main Control Unit (MCU)
parameters of the MU and provides
telecommunication interface for local monitoring.
Connects with modules and MCU; local
Distribution Board
commissioning via RJ45 port.
Converts the input voltage into stable DC to
Power Supply Unit (PSU)
supply power for other modules and to charge the
internal Li-ion battery.
Li-ion Battery
Will supply power to MCU after power failure.
Table 1: MU Constitution
The RU consists of:
Identifier
Power Supply Unit (PSU)
700MHz Duplexer
1900/850 Dualband Combiner
Optical TX/RX Module
Integrated RF Module
DL PA Module
MCU
Li-ion Battery
Functional Description
Converts the input voltage into stable DC to supply
power for other modules and to charge the internal
Li-ion battery.
Fulfills 700MHz signal conversion.
Duplexes and combines both 1900MHz and
850MHz signals.
Completes optical signal and RF signal
conversion.
Combines the UL LNA and pre-amplifies the DL
signals.
Amplifies the desired signal.
Is used to control and monitor the operation
parameters of the RU and provides
telecommunication interface for local monitoring.
Will supply power to MCU after power failure.
Table 2: RU Constitution
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 17
USER MANUAL FOR RA-5700
2.5
KIT OF PARTS
For this system, the following are shipped:
Product Identifier
Description
Fuse
N/A
N to SMA Connector
N female to SMA male
Modem Antenna
OOA-360/V02-SD
Feeder Cable
N male to N male; customized length accordingly
Field Commissioning Cable
N/A
Optical Jumper
FC/APC, 1m
Power Supply Cable
N/A
Philips Pan Head Screw
GB/T818, M5x10
Table 3: MU KOP
Product Identifier
Description
Allen Key
5mm
Clamp
T3-099901-5202
Carriage Bolt (L>120)
M12x160
External Alarm Cable
N/A
Field Commissioning Cable
N/A
Fuse
N/A
Hex Bolt
M8x12
Mounting Rack
RA-5700-5825
Masonry Bolt
M10x110
Nut
M12
Optical Jumper
Quantity
Quantity
Power Supply Cable
N/A
Plain Washer
Φ8
Spring Washer
Φ8
Factory Test Report
This manual on CD
Table 4: RU KOP
End of Section
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 18
USER MANUAL FOR RA-5700
3 INSTALLATION
3.1
WARNINGS AND ALERTS
Laser
Laser light can cause damage to eyes. Laser light is not visible. Viewing it directly does not cause pain.
The iris of the eye will not close when viewing a bright light. Consequently, serious damage to the retina of
the eye is possible. NEVER LOOK INTO THE END OF A FIBER WHICH MAY HAVE A LASER
COUPLED TO IT.
Radio Frequency Energies
There may be situations, particularly for workplace environments near high-powered RF sources, where
recommended limits for safe exposure of human beings to RF energy could be exceeded. In such cases,
restrictive measures or actions may be necessary to ensure the safe use of RF energy.
High Voltage
The equipment has been designed and constructed to prevent, as far as reasonably, practicable danger.
Any work activity on or near equipment involving installation, operation or maintenance must be, as far as
reasonably, free from danger.
Where there is a risk of damage to electrical systems involving adverse weather, extreme temperatures,
wet, corrosive or dirty conditions, flammable or explosive atmospheres, the system must be suitably
installed to prevent danger.
Protective Earthing
Equipment provided for the purpose of protecting individuals from electrical risk must be suitable for the
purpose and properly maintained and used.
Handling Precautions
This covers a range of activities including lifting, lowering, pushing, pulling, carrying, moving, holding or
restraining an object, animal or person. It also covers activities that require the use of force or effort, such
as pulling a lever, or operating power tools.
Electrostatic Discharge (ESD)
Observe standard precautions for handling ESD-sensitive devices. Assume that all solid-state electronic
devices are ESD-sensitive. Ensure the use of a grounded wrist strap or equivalent while working with
ESD-sensitive devices. Transport, store, and handle ESD-sensitive devices in static-safe environments.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 19
USER MANUAL FOR RA-5700
3.2
SITE PLANNING CONSIDERATIONS
Site Considerations
The MU can be located indoors to facilitate coupling of BTS signals and power supply connections. The
ALC range of received BTS signal is -10~10 dBm. Hence, an appropriate coupler must be used according
to the BTS output power.
The site consideration for RU is listed below:
The distance between the service antenna of RU and coverage area should satisfy line of sight
requirements for maximum coverage area.
The maximum fiber length is 13km, with a maximum path loss of 5dB.
The system delay of the optical system must be taken into consideration when there are neighboring
BTS sites overlapping in coverage.
Installation Location
Mounting surface shall be capable of supporting the weight of the equipment.
In order to avoid electromagnetic interference, a proper mounting location must be selected to minimize
interference from electromagnetic sources such as large electrical equipment.
Environmental
Humidity has an adverse effect on the reliability of the equipment. It is recommended to install the
equipment in locations having stable temperature and unrestricted air-flow.
The installation location for the system should be well ventilated. The equipment has been designed to
operate at the temperature range and humidity level as stated in the product specifications that of
temperature ranges from 32~104 F (MU)/ -27~122 F (RU) and the relative humidity is at most
85%(MU)/95%(RU).
Direct day light to the RU should be avoided. If the direct day light temperature exceeds 104 F, a shelter
should be provided for it.
Powering
The power supply unit (PSU) provides power to all modules within the equipment. Depending on the
product variant, it is recommended that the PSU operates on a dedicated AC circuit breaker or fused
circuit.
Grounding Requirement
Verify that the equipment has been well grounded. This includes antennas and all cables connected to the
system. Ensure lightning protection for the antennas is properly grounded.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 20
USER MANUAL FOR RA-5700
Cable Routing
Depending on equipment configuration, a variety of types of cables are connected to the MU and RU:
coaxial cables, optical fibers, power cable, communication cable, and commissioning cable. Where
applicable, ensure cables are properly routed and secured so that they are not damaged.
Manual Handling
During transportation and installation, take necessary handling precautions to avoid potential physical
injury to the installation personnel and the equipment.
3.2.1 SYSTEM INSTALLATION CHECKLIST
Working space available for installation and maintenance for each mounting arrangement. Ensure
unrestricted airflow.
Ensure earthing point is within reach of the ground wire.
Ensure a power source is within reach of the power cord and the power source has sufficient capacity.
Where appropriate, ensure unused RF connectors are terminated.
Where appropriate, ensure unused optical fiber connectors are protected.
Do not locate the equipment near large transformers or motors that may cause electromagnetic
interference.
Reduce signal loss in feeder cable by minimizing the length and number of RF connections.
Ensure the equipment will be operated within the stated environment (refer to datasheet).
Where needed, couple BTS RF signal with a coupler to prevent damaging the equipment.
Where appropriate, confirm available of suitably terminated grade of RF and optical fiber.
Observe handling of all cables to prevent damage.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 21
USER MANUAL FOR RA-5700
3.3
INSTALLATION PROCEDURES
3.3.1 GOODS INWARDS INSPECTION
RA-5700 was factory tested, inspected, packed, and delivered to the carrier with utmost care. Do not
accept shipment from carrier which shows damage or shortage until the carrier's agent endorses a
statement of the irregularity on the face of the carrier's receipt. Without documentary evidence, a claim
cannot be processed.
Open and check each package against the packing list. For any shortage, contact Comba Telecom
Systems. Do not remove items from packing materials until installation.
3.3.2 TOOLS
See Appendix B for a full list of tools required for installation and maintenance.
3.3.3 PREPARATION
Optical Fiber:
Fiber optic cables require proper handling. Do not stretch, puncture, or crush the fiber cable(s) with
staples, heavy equipment, doors, etc.
Always maintain the minimum bending radius specified by the cable manufacturer. The minimum
bend radius is usually 10 times as the cable's outer diameter. In the case of single optical fiber that is
not in a cable, the minimum bending radius to be observed is 1.181inch.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 22
USER MANUAL FOR RA-5700
3.3.4 CABINET MOUNTING OF MU
Depending on the installation, should 2-post open-rack are to be used, the mid-mounting brackets are to
be used. For rack or cabinet mounting, the mid-mounting brackets are to be removed from the 4U shelf.
Cage nut and screws are not supplied. Unless being recommended by rack manufacturer, M5 cage nut /
bolt are to be used.
Master Unit
19" Shelf
Figure 8: Cabinet Mounting of 19” Shelf
3.3.5 RU MOUNTING RACK DIMENSION
The mounting arrangement of the RU is used for mounting the RU to a wall. The figure below shows the
location of the holes for the mounting tabs.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 23
0.51
USER MANUAL FOR RA-5700
8- 0.51
10.63
0.51
3.35
4.72
7.87
Figure 9: RU Mounting Rack Dimension
3.3.6 WALL MOUNTING OF RU
Hereinafter are the mounting steps for wall mounting:
Drill holes on the wall for masonry bolts according to the dimension of the upper/lower mounting tabs
indicated above.
Insert the masonry bolts (M10x110) to the wall.
Hook the enclosure onto the masonry bolts, and then lower the whole enclosure to make sure that
the bolts are fastened into the narrow slots of the mounting tabs.
Tighten nuts to secure the hex bolts and enclosure onto the wall.
Masonry Bolt
Mounting Rack
Plain Washer
Spring Washer
M10 Nut
M8x12 Hex Bolt
Figure 10: RU Wall Mounting
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 24
USER MANUAL FOR RA-5700
3.3.7 POLE MOUNTING OF RU
Secure the Mounting rack onto the pole using U bolt.
Hook the enclosure up onto the mounting rack and align the hole positions to that of the mounting
rack, then installed the rack bolts.
Use spanner to tighten hex bolts (M8x12) to mounting rack to complete the installation.
Clamp
Mounting Rack
Plain Washer
Carriage Bolt
Spring Washer
M8x12 Hex Bolt
Figure 11: Pole Mounting of RU
3.3.8 DRIP-LOOP
Comba recommends that every horizontal cable entry to the equipment forms a 'U' before it‟s entry to the
equipment. Any accumulated water on the cable will drip down at the bottom of the loop and will not climb
up to the equipment.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 25
USER MANUAL FOR RA-5700
3.4
EQUIPMENT CONNECTORS
The MU is connected via the connectors located on the front and back panel. The RU is designed for all
cables entries from the bottom of the enclosure. The figures below present the connectors of MU and RU.
3.4.1 MU CONNECTORS
Connectors on the MU are identified as below:
700MHz 850MHz 1900MHz AWS
OP1
OP2
OP3
OP4
PWR
RUN
ALM
MOD
OP1
OP2
OP3
OP4
MODEM
BTS_ALM
EXT_ALM
OMT
Figure 12: MU Front Panel Connectors
Identifier
700MHz, 850MHz,
1900MHz, AWS
EXT_ALM
OP1~OP4
MODEM
BTS_ALM
OMT
Functional Description
RF connector for various network systems.
DB9 (female) connector, for external alarm.
FC/APC optic interface, each interface is used to connect with a RU.
Includes SIM insertor, MODEM indicator and MODEM RF connector.
DB9 (female) connector.BTS external alarm reporting,
RJ45 connector, local OMT commissioning port, connects with PC to realize
local commissioning.
Table 5: MU Front Panel Connections
100-240V~
50/60Hz
Figure 13: MU Back Panel Connectors
Identifier
100-240V~50/60Hz
Functional Description
A power supply cable for power supply
Table 6: MU Back Panel Connections
The voltage identification is a variant due to electricity system diversity of global regions. The power cable gland
might be identified for AC 220V, AC 110V, AC 220V/110V, DC -48V, or DC +24V respectively. Please refer to
specific product or contact local sales if any doubt.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 26
USER MANUAL FOR RA-5700
3.4.2 RU CONNECTORS
Connectors on the RU are identified below:
OMT
EXT_ALM
OP OUT/IN
100-240V~ 50/60Hz
RX_EXT
ANT 700
ANT
850+1900
TX_EXT
Figure 14: RU Connectors
Identifier
100-240V~50/60Hz
ANT 850+1900,
ANT700
OP OUT/IN
OMT
EXT_ALM
TX_EXT
RX_EXT
ALM LED Indicator
RA-5700 QI
ENU Status : 1-1-2
Functional Description
A power supply cable for power supply
Connect with TX/RX antenna via coaxial cable.
OP uplink/downlink FC/APC optic connector, connects with MU OP
connector via optical fiber.
Connects with PC to fulfill local commissioning.
7-pin CPC connector, for external alarm..
N-female connector, for TX output extension of a new band.
N-female connector, for RX input extension of a new band.
Synchronized indicator of LED4 on MCU
Table 7: RU Connections
Copyright - refer to title page
Page 27
USER MANUAL FOR RA-5700
3.5
EQUIPMENT CONNECTION
3.5.1 GROUNDING CONNECTION
Ground connection
To ensure safe operation of the product, a ground (earth) connection is required. For single phase AC
power source, the product must be grounded by connecting the “earth wire” of the power cord to the
ground terminal of the AC supply. For operating this product with DC power system (such as rectifiers),
the product should not be connected to power systems that switch open the return lead because the
return lead could function as the ground (earth) connection for the equipment.
Protective Ground Connection
The enclosure must be grounded securely by connecting a copper wire (CSA 16mm ) to the grounding
terminal on the equipment/rack, and the other end to a protective ground (i.e. building earth point). An
internationally acceptable colour code of the ground connection wire is green/yellow.
Such a ground connection implements the “Protective Ground Connection”, and must be connected to the
equipment at the designated ground point. In general, do not connect the supply before establishing an
adequate ground (earth) connection.
MU Grounding Connection
Connect the grounding terminal located on the back panel of MU to a protective ground (i.e. building earth
point).
RU Grounding Connection
The equipment must be grounded securely. Connect a copper wire to the grounding terminal on the
mounting tab/enclosure, and connect the other end to a protective ground (i.e. building earth point). An
internationally acceptable coloring code of the ground connection wire is green/yellow.
3.5.2 LI-ION BATTERY CONNECTION
Li-ion battery is provided with this system to ensure power is supplied to the system monitoring unit and
MCU and to ensure the alarm message could be sent to OMC effectively in case of mains power failure.
Caution: Be careful of the risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
3.5.3 OPTICAL CONNECTION
MU is connected to RU via optical fiber (length<13km). Connect MU front panel‟s OP1-OP4 with RU‟s OP
interfaces respectively.
Refer to the following connection:
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 28
USER MANUAL FOR RA-5700
OMT
EXT_ALM
OP OUT/IN
100-240V~50/60Hz
ANT
700
RX_EXT
ANT
850+1900
TX_EXT
700MHz 850MHz 1900MHz AWS
OP1
OP2
OP3
OP4
PWR
RUN
ALM
MOD
OP1
OP2
OP3
OP4
MODEM
BTS_ALM
EXT_ALM
OMT
Figure 15: Optical Connection
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 29
USER MANUAL FOR RA-5700
3.5.4 EXTERNAL ALARM CONNECTION
For MU, this is a DB9 connector. The following figure and table show the pin allocation and definition. Pin
numbering are shown looking-into the connector on the enclosure.
EXT_ALM 1
7 EXT_ALM
EXT_ALM 3
EXT_ALM 5
Figure 16: Pins Allocation for “EXT_ALM” Port for MU
Pin
number
Alarm
definition
EXT.
Alarm 1
Reserved
EXT.
Alarm
8~9
Reserved
EXT.
Alarm 3
Reserved
EXT.
Alarm 4
Reserved
Table 8: Pin Definition of “EXT_ALM” Port for MU
For RU, this is a 7-pin CPC connector. The following figure and table show the pin allocation and
definition. Pin numbering are shown looking-into the connector on the enclosure.
Figure 17: Pins Allocation for “EXT_ALM” Port for RU
Pin number
Alarm
definition
EXT.
Alarm 1
EXT.
Alarm 2
EXT.
Alarm 3
GND
Reserved
Reserved
Reserved
Table 9: Pin Definition of “EXT_ALM” Port for RU
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 30
USER MANUAL FOR RA-5700
3.5.5 BTS ALARM CONNECTION
The equipment alarms can be signaled to the BTS via voltage-free relay contacts. The voltage-free relay
connections are connected to the DB-9 port “BTS_ALAM” located on the MCU of MU. The following figure
and table shows the pin allocation and definition.
BTS_OPEN
BTS_ COM
BTS_CLOSE
Figure 18: Pins Allocation for “BTS_ALM” Port
Pin Number
4~9
Definition
BTS_OPEN
BTS_COM
BTS_CLOSE
NC
Description
Connects to the open terminal of the voltage free relay.
Connects to the common terminal of the voltage free relay.
Connects to the close terminal of the voltage free relay.
Reserved.
Depending on OMT/OMC configuration, alarm to BTS can be signalled equipment by either: a) pin1 and
pin2 „open‟ or b) Pin2 and Pin3 „close‟.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 31
USER MANUAL FOR RA-5700
3.5.6 CONNECT TO PC
The local commissioning and management for MU and RU is achieved through connecting to the OMT
PC locally.
Connect MU to PC
Connect”OMT” port (RJ45) to the serial port of PC with ethernet cable supplied to achieve local monitoring
and management. A build-in wireless modem is available for OMC connection to realize remote
commissioning.
Connect RU to PC
Local commissioning and management of RU is achieved through “OMT” port and the OMT PC via field
commissioning cable supplied.
With the equipment enclosure opened, the engineering OMT can be used to connect internally.
End of Section
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 32
USER MANUAL FOR RA-5700
4 COMMISSIONING
4.1
PRE-COMMISSIONING TASKS
After equipment installation, perform the following steps before equipment powering and commissioning,
check that the expected voltage, current, and power levels do not violate any ratings. Double check all
connections including ground before applying power. Do not manipulate circuits or make changes when
power is applied:
Visually inspect the power connection within the equipment. Ensure that the power cable is correctly
and securely connected, including grounding wire, RF cable and optical cable.
Check grounding connection and verify that the ground resistance is less than 5Ω.
Connect the equipment to the PC installed with OMT software.
With the MU switched on, RU installed and all cablings connected, apply power to the RU by switching
on the PSU switch on the integrated PSU.
Monitor the initialization of the MU though the LEDs on the front panel of MCU unit, while for RU, it is
through the LEDs on the MCU unit integrated. Refer to detailed LEDs information in the next section.
4.2
MU/RU RESET TIME DURATION
To reset the MU and RU, system takes MU<90s and RU<50s.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 33
USER MANUAL FOR RA-5700
4.3
LED INDICATORS
4.3.1 MU LED INDICATORS
Diagnostic LEDs are located on the MU; each indicates the status of a particular function:
Identifier
POWER
Color
Green
RUN
Green
ALM
Red
MOD
Red
OP1-OP4
Green
Indication
It stands in green when power on.
Operation indicator – power is supplied to the MU. Flashes once every
second to indicate normal system operation.
Alarm indicator. ON = alarm; OFF = no alarm
Diagnostic LED for FSK communication and MODEM operation. Flashes
once every two seconds to indicate normal communication between MU and
RU.
When the green indicators are on, the relative optical channel is in normal
reception.
Table 10: MU LED Indicators
4.3.2 RU LED INDICATORS
LED Diagnostic indicators are located on the MCU integrated in the RU; each indicates the status of a
particular function.
Identifier
ALM (on
bottom panel)
Colour
Red
LED 5
Green
LED 4
Red
LED 3
Red
Indication
Synchronized LED indicator of LED4 on MCU. Alarm indicator. ON = alarm;
OFF = no alarm
Operation indicator – power is supplied to the RU. Flashes twice every 2
seconds to indicate normal system operation.
Alarm indicator. ON = alarm; OFF = no alarm
Diagnostic LED for FSK communication. Flashes once every two seconds to
indicate normal communication between MU and RU.
Table 11: RU LED Indicators
All LEDs in MU (except power indicator) will flash simultaneously 3 times after equipment power-up. Then
RUN indicator flashes every second to indicate system normal operation.
The LEDs LED5, LED4, LED3 will flash simultaneously 3 times after equipment power-up. During system
self-checking, LED5 flashes slowly. Then it flashes every second to indicate system commissioning can
be proceeded with.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 34
USER MANUAL FOR RA-5700
4.4
WEB OMT
4.4.1 CONNECTION FROM PC TO EQUIPMENT
Before accessing to the OMT, physical connection between the PC and the equipment must be made. A
straight-through RJ45 cable shall be applied for the connection.
Comba recommends an IE8 browser to connect with Web OMT.
The default IP address of RA-5700 MU is 192.168.8.101 and RU is 192.168.8.102. Subnet mask is
255.255.255.0.
Execute the IE browser and enter 192.168.8.101/102 in the address bar. A pop-up window will be shown,
requiring user name and password. The default user is admin and password is 123456.
Figure 19: Web OMT Access
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 35
USER MANUAL FOR RA-5700
Figure 20: Log in
Items
PC IP Address
PC Subnet Mask
PC Gateway
System IP Address
System Subnet Mask
User name
Password
Default Value
Automatically distributed by system
255.255.255.0
Automatically distributed by system
192.168.8.101 (for MU) / 192.168.8.102 (for
RU)
255.255.255.0
admin
123456
Table 12: IP Setting Quick Look-up Table
4.4.2 OMT CONFIGURATION
OMT parameters include: Common Information, RF Information, Alarm Information, Properties
Information, User Manager and Help.
4.4.3 SYSTEM INFORAMTION
Click on [System Information], system information will be displayed in the right interface of the OMT
screen. In the interface the site ID of MU is described and the currently accessed unit is indicated.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 36
USER MANUAL FOR RA-5700
Figure 21: System Information
As illustrated, MU in green is under monitoring,
To switch to the RU or other sites, customer can choose RU (in grey) or other site by clicking to
switch to RU or other sites. It usually takes less than 40s.
Firmware Update
Figure 22: Firmware Update
For fiemware update, system takes approx 10mins based on the current version. Normally it takes
less than 3mins.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 37
USER MANUAL FOR RA-5700
Maintenance
Figure 23: Maintenance
1> Firmware Switch: can switch to the previous firmware version which was saved in the system when
update to current firmware. It is to say there are 2 firmware versions available in same system. This
function is not available in current phase.
2> Device Reboot: restart the device
3> Clear History Alarm: delete all history alarm records
Config. Data Import
Figure 24: Data Import
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 38
USER MANUAL FOR RA-5700
Data Export
Figure 25: Data Export
[Export]: Export all site records. The records can be exported to a CSV file.
1> Config Data Export: can export the config. data and save in PC. The exported data can be input to the
same kind of equipment if necessary.
2> Status Data Export: can export status data and save in PC. The data is save-only, can not import.
3> Usally, cofig a data import and export, it takes less than 5s.
4.4.4 RF INFORMATION
It is recommended to configure the following RF parameters for the first installation.
Switch
Switch is to enable/disable power for internal modules. When user checks and sets non-RF parameters,
such as checking physical antenna connection, switching off will disable equipment power temporarily to
protect PA in operation.
Figure 26: Switch
Config:
Select the required state in setting columns of RF information window for RF switch, then press [ON] or
[OFF] button to finish the configuration operation.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 39
USER MANUAL FOR RA-5700
Alarm Threshold
Users can set alarm threshold according to the specific situation. If the measured value is lower than the
threshold lower limit or more than the threshold upper limit, the appropriate alarm will be generated.
Figure 27: Alarm Threshold
Temperature
Figure 28: Temperature
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 40
USER MANUAL FOR RA-5700
ATT
Figure 29: ATT
[ATT]: read-only parameters. ATT = Rating Gain - Gain
Power
Figure 30: Power
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 41
USER MANUAL FOR RA-5700
Gain
Figure 31: Gain
Rating Gain: be set before delivery. Comba recommends no change of rating gain value.
Gain: User can set according to the real application.
Miscellaneous
Figure 32: Miscellaneous
4.4.5 ALARM INFORMATION
Click any tree node in [Alarm Info] group, [Alarm Information] window will appear in the right side. The
figures below show the alarm information.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 42
USER MANUAL FOR RA-5700
Master Alarm
Figure 33: Master Alarm
Channel Alarm
Figure 34: Channel Alarm
External Alarm
Figure 35: External Alarm
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 43
USER MANUAL FOR RA-5700
4.4.6 PROPERTIES INFORMATION
Equipment ID
Equipment ID is to be configured after local commission has been completed, which includes Site ID and
Site Sub ID.
Item
Site ID
Site Sub ID
Description
Site ID is the unique equipment identification. It is a hexadecimal string of eight
characters in the range of [0x00000000-0xFFFFFFFF]. e.g. 12345678
Site Sub ID is used for Master-Slave System. It is the unique identification of each
Master/ Slave Unit and is a hexadecimal string of two characters in the range of
[0x00-0xFF]
For the system located with single equipment, the Site Sub ID should be 0xFF.
e.g. 00
For Master-Slave system, the Site Sub ID for Master Unit is 0x00, and the Site
Sub ID for each Slave Unit is represented in the range of [0x00-0xFE] in
ascending order. e.g. Master Site ID: 00 Slave Site ID: 01
Table 13: Equipment ID
Figure 36: Equipment ID
Equipment Info.
Figure 37: Equipment Info.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 44
USER MANUAL FOR RA-5700
Site Location
Figure 38: Site Location
[Site Location]: input the current longitude and latitude in the blank.
System Clock
Figure 39: System Clock
[System Clock]: it shows the current time/date information. It is settable.
Comm. Config
The Comm. Config information requires to be manually entered by users after successful connection to
the equipment.
Figure 40: Comm. Config.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 45
USER MANUAL FOR RA-5700
SMSC NO. (Equipment
SIM Card)
OMC Server IP
OMC IP Port No.
GPRS User Name
GPRS Password
Alarm Notice Phone NO.
Alarm Notice Phone NO.
Enable
The SMS centre number of SIM card in equipment.
OMC IP Address. For equipment which support TCP/IP.
OMC IP Port No. For equipment which support TCP/IP.
Login GPRS network user name.
Login GPRS network password.
The telephone number of alarm receiver.
Enable the telephone number of alarm receiver.
Firmware Information
Figure 41: Firmware Information
4.4.7 USER MANAGEMENT
User Info.
Figure 42: User Information
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 46
USER MANUAL FOR RA-5700
Set Session Time
Figure 43: Set Session Time
[Set Session Time] is to set the automatic log-off time.
4.4.8 HELP
Help
Figure 44: Help
About
Figure 45: About
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 47
USER MANUAL FOR RA-5700
4.4.9 CHANGE PASSWORD
Click [User Info.]-> select the wanted user as illustrated.
Figure 46: Password Configuration
Sumit the request of buttom in the bottom, a pop-up window might shown out to indicate an
on-going step.
Figure 47: Change Password
End of section
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 48
USER MANUAL FOR RA-5700
5 TROUBLESHOOTING
Following installation and commissioning, occasional operation tasks to handle alarms may be required:
Alarm
Alarmcondition
condition
Diagnosis
Diagnosis
AC Power Failure Alarm/ DC
Power Fault Alarm
Check AC power cable and verify AC mains supply is normal.
During Power Fault alarm, DC power supply has no output. Check if
DC output power is overloaded or short-circuited. The PSU could be
faulty.
Li-ion Battery Fault Alarm
Check the connection between battery and power supply cable. Or
replace the faulty modules and return it to the factory for repair.
DL Input Power Overload alarm
External Alarm
Check to make sure if the external device connected is working
Eliminate alarm by correct setting ofnormally
DL Input Power Overload threshold. If the setting is OK but alarm
persists, the DL input power might be higher than the threshold. Increase the attenuator to reduce the
Eliminate
correct
setting
of temperature
if alarmof
OverTemperature
alarm
input
power
or replace
the coupler with
a newalarm
one ofbyhigh
coupling
effect.
Check the threshold,
cable connection
can not be cleared, apply climatic protection to the system under
the DT port to the BTS.
severe environment.
Door Open Alarm
Check whether the enclosure door is closed.
ALC Alarm
Check to see if PA alarm or DL input power overload alarm occur
via OMT/OMC. If so, adjust DL input power or replace a new PA.
Alarm occurs when automatically shut off the system. Turn on the
Shutdown
Alarm
External
Alarm
system and check if the DL output power overload alarm persists,
Check to make sure if the external adjust
device the
connected
is working
normallythreshold to a proper value.
DL output
power overload
Alarm occurs when manually shut off the system. Turn on the
Manual Shutdown Alarm
system to eliminate the alarm.
Alarm occurs when the module software failed. Reboot the system
Module Software Alarm
or update the software.
Optical TX Alarm
The optical power at the TX port of the Optical TX/RX Module is
Li-ion Battery Fault Alarm
lower than the minimum requirement, which is resulted by the faulty
of the
TX part
Optical TX/RX Module or damaged optical
Replace the faulty modules and return
it tooptical
the factory
forofrepair.
fiber link. If so, replace the optical TX/RX module. If not, check the
working status of the optical fiber to eliminate the alarm.
The optical RX part of Optical TX/RX Module is faulty. Check and
Optical RX Alarm
replace the faulty module and return it to the factory for repair.
Check power and signal connections of respective modules. If the
UL LNA, DL PA alarms
power and signal wire connections are OK, then the respective
Over- Temperature alarm
modules may be faulty. Replace the faulty modules and return it to
Eliminate alarm by correct setting ofthe
temperature
including normal and severe. If alarm can not
factory for threshold,
repair.
be cleared, apply climatic protection to the equipment.
Master/Slave Unit Link Alarm
The communication between the MU and RU is abnormal. Check
the working status of Optical TX/RX Module and FSK.
DL Input Power Overload
Alarm
Eliminate alarm by correct setting of DL Input Power Overload
threshold. If the setting is OK but alarm persists, the DL input power
might be higher than the threshold. Decrease the gain to reduce the
Optical TX Alarm
input power or replace the coupler with a new one of high coupling
effect.
The optical TX part of Optical TX/RX Module is faulty. Check and replace the faulty module and return it to
the
repair.
DLfactory
Outputfor
Power
Overload
Eliminate alarm by correct setting of DL Output Power Overload
Alarm
threshold. If the setting is OK but alarm persists, the DL output
power might be higher than the threshold. Decrease the gain to
reduce the output power.
DL Output Power Low Alarm
Eliminate alarm by correct setting of DL Output Power Low
Optical RX Alarm
RA-5700
QI power at the RX port of the Optical
Copyright
- refer to
title page
Page 49
The optical
TX/RX
Module
is lower than the minimum requirement,
ENU
Status
: 1-1-2 by the faulty of the optical TX part of Optical TX/RX Module or damaged optical fiber link.
which
is resulted
If so, replace the optical TX module. If not, check the working status of the optical fiber to eliminate the
alarm.
USER MANUAL FOR RA-5700
threshold. If the setting is OK but alarm persists, the DL output
power might be lower than the threshold. Increase the gain to high
up the output power.
External Alarm
Check to make sure if the external device connected is working
normally
Table 14: Alarms Diagnosis
End of Section
6 MAINTENANCE
The RA-5700 system is designed for trouble-free operation and generally does not need maintenance.
Maintenance activities should only be carried out by trained personnel.
The equipment operation status can be observed remotely through OMT/OMC.
Periodic inspection of the system is recommended. The recommended tasks include:
Measurement of the return loss of the feeder system.
Ensure the stable connection of cables, power cords and facilities located indoor.
Inspect and record operation status and parameters, such as receive signal level, DL output power of
the system, from OMC or OMT.
Check the PSU voltage of MU.
Verify that the actual coverage effects have not degraded.
Check the working status of optical TX/RX power.
Check the controlling and monitoring function.
Verify lightning and grounding protection is in good condition.
End of Section
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 50
USER MANUAL FOR RA-5700
7 APPENDICES
7.1 APPENDIX A: BAND SELECTIVE UNIT USER MANUAL
7.1.1 BS-8132 BSU (BAND SELECTIVE UNIT)
1) Working frequency:
1) Applications:
1> A1+A2
2> B1+B2
3> A band + B band
To realize the channel function, please refer to the following table;
Channel 1/2 ON
Channel 1 ON, Channel 2 OFF
Channel 1
A2+B2 (1.5MHz~4MHz set available)
A band + B band (total 25MHz)
NOTE that Channel 2 can only realize A1 + B1 (1.5MHz~21MHz set avilable) bandwidth.
2) Set channel No. as center channel number
Bandwidth= (Upper edge No. – Lower edge No.) x 30KHz + 1.23MHz
3) CDMA850 channel No.
Working Band
Channel
DL Channel No.
UL Channel No.
A1
1011
314
B1
354
647
A2
687
697
B2
737
779
A band + B band
1011
779
Table 15: Bandwidth and Channel No.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 51
USER MANUAL FOR RA-5700
7.1.2 BS-1933 BSU
1) Working frequency:
PCS Band (1850-1990 MHz): Up to 20 MHz of spectrum in no more than 3 non-contiguous PCS subbands of 5, 10 or 15 MHz each based on VZW‟s PCS licenses.
2) Applications:
Channel 1~3 is 5MHz~15MHz bandwidth settable while 60MHz can be set and which can not be
iterant set.
The minimum interval between Lower edge No. and Upper edge No. is 75, while the maximum is 275.
3) Set channel No. as center channel number
Bandwidth= (Upper edge No. – Lower edge No.) x 50KHz + 1.25MHz
4) CDMA1900 channel No.
RA-5700 QI
ENU Status : 1-1-2
Working Band
DL Channel No.
UL Channel No.
13
288
313
388
413
688
713
788
813
888
913
1186
C1
913
1050
Copyright - refer to title page
Page 52
USER MANUAL FOR RA-5700
C2
1063
1188
C3
913
988
C4
1013
1088
C5
1113
1188
7.1.3 BS-8132&BS-1933 BSU LAYOUT
5.2"
17.2"
19"
17.3"
DT
MT
RUN
ALM
PWR
RS-232
Figure 48: BSU Layout
7.1.4 BS-8132&BS-1933 KOP
For the system, the following are shipped.
Product Identifier
Description
Power Supply Cable
Field Commissioning Cable
Quantity
R-9122C/R-9122AC
RF Jumper
N to SMA Connector
N female to SMA male
Feeder Cable
N male to N male; customized length accordingly
Philips Pan Head Screw
GB/T818, M5x10
Table 16: BS-1933 KOP
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 53
USER MANUAL FOR RA-5700
Product Identifier
Description
Quantity
Power Supply Cable
Field Commissioning Cable
R-9122C/R-9122AC
RF Jumper
N to SMA Connector
N female to SMA male
Feeder Cable
N male to N male; customized length accordingly
Philips Pan Head Screw
GB/T818, M5x10
Table 17: BS-8132 KOP
7.1.5 BSU OMT
7.1.5.1 LOCAL TO OMT
After installing OMT software on the PC, connection to the equipment can be done locally.
Double click the OMT explorer icon, the OMT Explorer main screen window will appear.
7.1.5.2 LOCAL CONNECTION TO OMT
After database configuration is done successfully, the following window will pop up and select [Local
connection via RS-232] for local connection.
Figure 49: Connection Type
Select the desired communication port and click “OK”, it will enter into the main window of OMT.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 54
USER MANUAL FOR RA-5700
Figure 50: Serial Port Configuration
7.1.5.3 OMT CONFIGURATION
After entering the OMT main screen, click the “Connect” button on the toolbar, to connect the equipment
to the OMT. Successful connection will be indicated by a message “Online Ok” and equipment
parameters can be read and/or set.
Users can configure the parameters, and then offset the parameters according to desired coverage level
and interference to other BTS signals.
OMT parameters include: Common Information, RF Information, Alarm Information, and Properties
Information.
Figure 51: Main Window
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 55
USER MANUAL FOR RA-5700
7.1.6 BS-1933 OMT
7.1.6.1 Common Information
System Information
Click on [System Info.] within Equipment Information, system information will be displayed in the right
interface of the OMT screen.
Figure 52: System Information
Auto-Read
Customer can set which parameters to be read automatically at a particular time interval.
Click on the [Auto-Read] node in the right interface the parameters will be displayed in the right interface.
Select the desired parameters and click [Save] button. Input a number in the time interval field and click
the adjacent [Save] button to admit the setting.
Example: If the time interval is 3 seconds, then the selected alarm parameters will be read automatically
every 3-second.
Figure 53: Auto-Read
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 56
USER MANUAL FOR RA-5700
7.1.6.2 RF Parameter
It is recommended to configure the following RF parameters for the first installation.
SWITCH
Switch is to enable/disable power for internal modules. When user checks and sets non-RF parameters,
such as checking physical antenna connection, switching off will disable equipment power temporarily to
protect PA in operation.
Figure 54: Switch
Config:
Select the required state in setting columns of RF information window for RF switch, then press [Enter] or
[Config] button to finish the configuration operation.
CHANNEL NO.
Channel No. includes Low Edge Channel No. and High Edge Channel No. The value in [MaxValue]
column is the upper limit of the range, while the value in [MinValue] column is the lower limit of the range.
Figure 55: Channel NO.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 57
USER MANUAL FOR RA-5700
7.1.6.3 Alarm Information
Figure 56: Channel Alarm
Config:
Tick the check box of [Item select] and [Enable] of the desired parameters and click [config] button to
finish configuration operation.
Notice: [Enable] box
is to enable the alarm monitoring for system. Only if users enable the alarm by
ticking the [Enable] box, the alarms can be monitored by the OMT/OMC.
7.1.6.4 Properties Information
EQUIPMENT ID
Equipment ID is to be configured after local commission has been completed, which includes Site ID, and
Site Sub ID.
Figure 57: Equipment ID
See the table below for configuration details of each parameter.
Item
Site ID
Site Sub ID
RA-5700 QI
ENU Status : 1-1-2
Description
Site ID is the unique equipment identification. It is a hexadecimal string of eight
characters in the range of [00000000~FFFFFFFF]. e.g. 00000000
Site Sub ID is used for Master-Slave System. It is the unique identification of each
Master/ Slave Unit and is a hexadecimal string of two characters in the range of
Copyright - refer to title page
Page 58
USER MANUAL FOR RA-5700
[00~FF].
For the system located with single equipment, the Site Sub ID should be FF.
For Master-Slave system, the Site Sub ID for Master Unit is 00, and the Site Sub
ID for each Slave Unit is represented in the range of [01~FE] in ascending order.
e.g. Master Site ID: 00, Slave Site ID: 01
7.1.7 BS-8132 OMT
7.1.7.1 Common Information
System Information
Click on [System Info.] within Equipment Information, system information will be displayed in the right
interface of the OMT screen.
Figure 58: System Information
Auto-Read
Customer can set which parameters to be read automatically at a particular time interval.
Click on the [Auto-Read] node in the right interface the parameters will be displayed in the right interface.
Select the desired parameters and click [Save] button. Input a number in the time interval field and click
the adjacent [Save] button to admit the setting.
Example: If the time interval is 3 seconds, then the selected alarm parameters will be read automatically
every 3-second.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 59
USER MANUAL FOR RA-5700
Figure 59: Auto-Read
7.1.7.2 RF Parameter
It is recommended to configure the following RF parameters for the first installation.
SWITCH
Switch is to enable/disable power for internal modules. When user checks and sets non-RF parameters,
such as checking physical antenna connection, switching off will disable equipment power temporarily to
protect PA in operation.
Figure 60: Switch
Config:
Select the required state in setting columns of RF information window for RF switch, then press [Enter] or
[Config] button to finish the configuration operation.
CHANNEL NO.
Channel No. includes Low Edge Channel No. and High Edge Channel No. The value in [MaxValue]
column is the upper limit of the range, while the value in [MinValue] column is the lower limit of the range.
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 60
USER MANUAL FOR RA-5700
Figure 61: Channel NO.
7.1.7.3 Alarm Information
Figure 62:Channel Alarm
Config:
Tick the check box of [Item select] and [Enable] of the desired parameters and click [config] button to
finish configuration operation.
Notice: [Enable] box
is to enable the alarm monitoring for system. Only if users enable the alarm by
ticking the [Enable] box, the alarms can be monitored by the OMT/OMC.
7.1.7.4 Properties Information
EQUIPMENT ID
Equipment ID is to be configured after local commission has been completed, which includes Site ID, and
Site Sub ID.
Figure 63: Equipment ID
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 61
USER MANUAL FOR RA-5700
See the table below for configuration details of each parameter.
Item
Site ID
Site Sub ID
Description
Site ID is the unique equipment identification. It is a hexadecimal string of eight
characters in the range of [00000000~FFFFFFFF]. e.g. 00000000
Site Sub ID is used for Master-Slave System. It is the unique identification of each
Master/ Slave Unit and is a hexadecimal string of two characters in the range of
[00~FF].
For the system located with single equipment, the Site Sub ID should be FF.
For Master-Slave system, the Site Sub ID for Master Unit is 00, and the Site Sub
ID for each Slave Unit is represented in the range of [01~FE] in ascending order.
e.g. Master Site ID: 00, Slave Site ID: 01
7.1.8 BS-8132&BS-1933 BSU CONNECTORS
DT
MT
RUN ALM PWR
RS232
Front Panel
AC 100V-240V
50Hz/60Hz
Rear Panel
Figure 64: BSU Connectors
Identifier
DT
MT
RUN
ALM
PWR
RS232
AC 100-240V
50Hz~50Hz
RA-5700 QI
ENU Status : 1-1-2
Functional Description
SMA connector, connects with BTS
SMA connector, BS-8132_MT connects with RA-5700D_850MHz connector
while BS-1933_MT connects with RA-5700D_1900MHz connector
Operation indicator
Alarm indicator
Power supply indicator
DB9 connector, connects to PC via engineering OMT.
Power supply
Copyright - refer to title page
Page 62
USER MANUAL FOR RA-5700
Coaxial cable
Female N
connector
SMA connector
Signal source
FC/APC
700Mhz Output
700Mhz
850Mhz
BS8132 Band
Selective Unit
1900Mhz
BS1933 Band
Selective Unit
SMA connector
RA5700
Triband
Master Unit
RA5700
Triband
Remote Unit
850Mhz+1900Mhz
Output
SMA connector
Figure 65: BSU Connection Overview
7.2 APPENDIX B: TOOLS FOR INSTALLATION AND MAINTENANCE
The following are the recommended list of tools new installation and routine maintenance:
Electronic drill
Allen Key
Adjustable spanner (Assorted size: 0.31~0.79 inch)
Philips Screwdriver
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 63
USER MANUAL FOR RA-5700
7.3 APPENDIX C: OVERDRIVE PROTECTION PROCEDURE
Overdrive Protection
Procedures
DL output power level >
DL output power level >
shutdown protection power
shutdown threshold
threshold
No overdrive detected
Threshold overtime
when detection is over.
Clean shutdown protection
Shutdown counter clear to
counter
null
Over threshold duration reaches
threshold persistent time > 5s
5 secs(Duration configurable)
100% (time can set)
and all detections over threshold
Automatic shutdown
Overdrive protection
protection ON (RF switch
activated, RF switch off.
OFF)
Overdrive
Shutdownprotection
protectioncounter
count ++11
Set
Start
timer
timer
of shutdown
of overdrive
protection
protection
time
shutdown protection time
Overdrive protection counter > 3
duration > 3 times (times: 1~255
(Range: 1~255)
available)
Overdrive
Shutdown
protection
protection
duration
time > >
15mins
15mins( Range:10mins~24hrs)
(time:10mins~24hrs)
Irreversible
Shutdown protection
RF swtich
turned
alarm:off,
permanent
overdrive
protectionshutdown
alarm is triggered
Restart RF signal switch
Turn on RF switch
Threshold overtime
Reset over threshold duration timer
Shutdown protection time
Reset overdrive protection duration timer
Clean shutdown protection
Reset overdrive protection counter
count
End
Extra time until RF
stablized
延延延延延延延延延延延
System initiation
RF signal “ON” manually
Reset over threshold
Threshold
durationovertime
timer
Y Shutdown
Reset overdrive
protection
protection
timeduration
Cleantimer
shutdown
protection
Reset overdrive
count
protection counter
Reboot automatic
Reactivate
overdrive
shutdownProcedures
protection
Protection
procedure
NOTE: 1. Independent control for each channel (850/1900/700)
2. Activate RF signal switch manually when the system is under permanent shutdown.
3. Overdrive protection procedures will be activated after manually turning on RF
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 64
USER MANUAL FOR RA-5700
7.4
APPENDIX D: SERVICING POLICY AND RETURN OF EQUIPMENT
The repair of individual units and modules of this equipment is not considered practicable without factory
facilities. It is, therefore, the policy of Comba whereby faulty units or modules are returned to the local
agent for repair.
To enable an efficient, prompt after sales service to be provided for the diagnosis, repair and return of any
faulty equipment, please comply with the following requirements.
Items to be sent for repair should be packaged so as to provide both electrostatic and physical protection
and a Repair Material Authorization (RMA) should be completed giving the required information. A sample
RMA form is provided in Appendix.
This request must be included with the item for repair. Items for repair should be sent to the nearest
Comba office:
COMBA TELECOM LTD.
Hong Kong Office
Address: 611 East Wing, No. 8 Science Park West Avenue, Hong Kong Science Park, Tai Po, Hong
Kong.
Tel: +852 2636 6861 Fax: +852 2637 0966
Singapore Office
Address: No. 1 Kaki Bukit View, #02-10 Techview, Singapore 415941
Tel: + 65 6345 4908 Fax: + 65 6345 1186
Thailand Office
Address: 240/34 Ayothaya Tower 18th Floor, Ratchadapisek Road, Huaykwang, Bangkok 10320, Thailand
Tel: +66 2274 1618-9 Fax: +66 2274 1620
India Office
Address: Suite No. 2, E-172, TSH House, Greater Kailash – I, New Delhi – 110 048, India
Tel: + 91 11 4173 9997 / 8 Fax: + 91 11 4173 9996
Sweden Office
Address: Gustavslundsvagen 147, S- 167 51 Bromma, Stockholm, Sweden
Tel: +46 8 25 38 70 Fax: +46 8 25 38 71
Brazil Office
Address: Avenida Engenheiro Luiz Carlos Berrini 1297, cj 122, 04571-090 Brooklin Novo, São Paulo,
Brazil
Tel: +55 11 35093700 Fax: +55 11 35093720
Dubai Office
Address: P.O. Box 450583, DUBAI, U.A.E.
Tel: +971 0 4 433 5320 Fax: +971 0 4 422 6774
US Office
Address: Comba Telecom Inc. 2390 Bering Drive, San Jose, CA 95131, USA
Tel: +1 408 526 0180 Fax: +1 408 526 0181
China Office
Address: No.10, Shenzhou Road, Guangzhou Science City, Guangzhou, China
Tel: + 86 20 2839 0000 Fax: + 86 20 2839 0136
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 65
USER MANUAL FOR RA-5700
7.5 APPENDIX E: RMA (RETURN MATERIAL AUTHORIZATION) FORM
End of Section
End of Document
RA-5700 QI
ENU Status : 1-1-2
Copyright - refer to title page
Page 66
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 66 Language : zh-CN Tagged PDF : Yes Title : Author : D Shiu Creator : Microsoft® Office Word 2007 Create Date : 2011:04:06 09:57:21 Modify Date : 2011:04:06 09:57:21 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools