Combi Catalyst 3011 Owner S Manual
2014-07-05
: Combi Combi-Catalyst--3011-Owner-S-Manual combi-catalyst--3011-owner-s-manual combi pdf
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
Catalyst Instruction Manual CombiUSA.com Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTION FOR FUTURE USE. Record the following information for quick reference. Note: Illustrations and photographs are only representative and not actual. Attach copy of sales receipt for future reference. Date of Purchased: _________________________ Model Number:___________ - ________________ (Located near rear of basket) Color: ______________________________________ Combi USA, Inc. ©2012 CombiUSA 3520 Westinghouse Blvd., Suite B • Charlotte, NC 28273 Customer Service 1.800.992.6624 WARNINGS & GENERAL SAFETY INFORMATION CombiUSA.com WARNING/////////////////////// AVOID SERIOUS INJURY FROM FALLING OR SLIDING OUT – ALWAYS USE RESTRAINT SYSTEM. NEVER LEAVE CHILD UNATTENDED! PLEASE READ THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE. In the event of damage or problems, discontinue use and contact Combi Customer Service for instructions: 1-800-992-6624 All operating and assembly procedures should be performed by an adult: • Avoid serious injury from falling or sliding out. Always use restraint system. • Never lift and carry the stroller while occupied. The stroller may fold. • Never allow your child to stand in or on the stroller.. • Never carry more than one child in stroller. Do not allow a child to ride or sit on areas of the stroller other than seat. • Never leave child unattended. • Never use the stroller on steep slopes, stairs, escalators, beaches, rough roads, mud, etc. • Never hang items on the handle or place items on canopy. This could cause the stroller to become unbalanced or tip over. • Always engage the brake when parking the stroller. • Never allow children to lean over sides of stroller. It may become unbalanced and tip over. • Excessive weight in basket (or items placed in basket which overflow the top or side of basket) may cause a hazardous condition. Do not load more than 10 lbs (4.5kg) in the basket. • To avoid finger entrapment or pinching, use care when folding and unfolding the stroller. Be certain the stroller is fully erected or folded, and locked in position before allowing your child near the stroller. • Completely remove all plastic bags and packing material before using this product to prevent a possible choking hazard. 2 Catalyst Instruction Manual • ALWAYS secure your child with the infant carrier restraint system before using it with the stroller. • This stroller is intended for walking speed only. NEVER use while jogging, skating, etc. • Child may slip into leg opening and strangle. Never use in reclined carriage position unless the restraint system is fully secured. • Completely remove all plastic bags and packing material before using this product to prevent a possible choking hazard. • Never carry stroller by using the approved infant car seat handle. • If unable to securely attach the approved Infant Seat to your stroller, discontinue use and contact Combi Customer Service. • TIPPING HAZARD: Never place weight on rear of infant seat while attached to the stroller. This could cause the stroller to become unbalanced and tip over. • Use only approved infant carriers with this stroller. • To ensure your child’s safety, please refer to an approved Infant Seat instruction manual before using it with the stroller. • WARNING: Do not use the seat in bassinet mode as a stand-alone unit. Serious injury may occur. Total Maximum weight of the child MUST NOT exceed 50 lb (22.7 kg). Note: All products specifications are subject to change without notice. Sizes and weights are intended as guides and are approximations. Combi® reserves the right to modify the products in its line during the course of the year. Non contractual media. Colors are as accurate as the media in which they appear allows. PARTS LIST VIEWING WINDOW CombiUSA.com HANDLE ADJUSTMENT BUTTON CANOPY BUMPER BAR FOLDING LEVERS RECLINE ADJUSTMENT STRAP HARNESS AND BUCKLE (NOT SHOWN) STROLLER FRAME SEAT STORAGE BASKET BRAKE SWIVEL LOCK & WHEEL RELEASE REAR WHEELS SWIVEL LOCK & WHEEL RELEASE FRONT WHEELS CAR SEAT ADAPTER* *CAR SEAT NOT INCLUDED Catalyst Instruction Manual 3 STROLLER ASSEMBLY CombiUSA.com INSTALL/REMOVE WHEELS TO INSTALL THE BACK WHEELS: Slide the wheel into the axle until it locks into place. TO REMOVE THE BACK WHEELS: Press the gray button on axle and pull the wheel out. TO INSTALL THE FRONT WHEELS: Slide each front wheel into the housing until it locks into place. TO REMOVE THE FRONT WHEELS: Press the gray button and pull wheel out from housing. UNFOLD STROLLER NOTE: Apply the brake before unfolding. STEP 1: Pull latch outward with your thumb to release locking mechanism. STEP 2: Pull up on the handle until frame locks open. STEP 3: Check that the frame is locked properly by gently pushing down on the handle. 4 Catalyst Instruction Manual STROLLER ASSEMBLY ATTACH/REMOVE SEAT CombiUSA.com STEP 1: Insert the posts on the sides of the seat into the slots of the frame. Push until you hear it “click” on both sides. STEP 3: To remove, push both release buttons (gray) and lift seat from the frame. STEP 2: Gently pull up on seat to be sure it is properly attached to the frame. NOTE: Seat can attach in either forward or rear-facing direction. ATTACH/REMOVE THE BUMPER BAR STEP 1: Insert metal post into bumper bar attachment slots found on both sides of seat. NOTE: The metal post can only be installed one way. Match oval guides beside the metal post to the oval guides on seat adapter. STEP 2: To remove, locate release lever on the inside of bumper bar latch. Use one finger to release button, and the other hand to release locking mechanism. Repeat on the other side. NOTE: White dot indicates location of release lever CANOPY INSTALLATION STEP 1: Snap each side of canopy attachment to seat frame, just above bumper bar. STEP 2: Pull canopy fabric over seat back. Attach snaps at the rear of the seat (x2). NOTE: Canopy coverage is adjustable. Catalyst Instruction Manual 5 STROLLER OPERATION SET THE BRAKE CombiUSA.com USING THE SWIVEL/LOCKING SYSTEM TO LOCK WHEEL SWIVEL: Align swivel wheel for forward travel, then push lever down to lock. TO UNLOCK: Slide button up NOTE: Lock wheel swivel if traveling through rough terrain or sand for improved stroller performance. HARNESS ADJUSTMENT TO LOCK THE BRAKE: STEP 1: Brake is located on the rear axel at the bottom center of the stroller frame. STEP 2: Push down on pedal to lock stroller. TO RELEASE BRAKE: Push the pedal up. ADJUST CANOPY STEP 1: Detach adjustment clip from the 5-point harness. TO ADJUST CANOPY: Pull sunshade out until you hear a “click”. Repeat until desired coverage is reached. VIEWING WINDOW Back Side Front Side STEP 2: While holding clip on strap, move the loop of the strap up or down to adjust. (Remove harness pad, if needed) STEP 3: Once adjust is complete, place harness pad back on to the strap and clip back into 5-point harness. 6 Catalyst Instruction Manual TO USE VIEWING WINDOW: To open window, lift window cover and fold forward, over canopy. To close window, fold window cover rearward and attach with magnet. STROLLER OPERATION SEAT POSITIONS RECLINE THE SEAT BACK CombiUSA.com POSITION #1 INFANT MODE POSITION #2 TODDLER RECLINE MODE POSITION #3 TODDLER UPRIGHT MODE TO ADJUST THE SEAT BACK RECLINE: Locate the recline mechanism on the rear of the seat back. Position fingers on the front and back of the red recline release lever, then pull down to desired position. WARNING: TO AVOID SERIOUS INJURY OR DEATH, never use Position #2 or #3 with an infant. ALWAYS use the restraint system. ADJUST SEAT POSITION RETURN TO UPRIGHT POSITION: While holding the recline strap, push recline mechanism to the desired position. Pull the lever near the top of the seat and tilt to desired position. Release the lever to lock in one of three preset positions. USING THE HARNESS ADJUST THE HANDLE POSITION TO LOCK: Slide both belt ends together until it locks. TO OPEN: Depress button at center and pull apart TO ADJUST THE HANDLE POSITION: Push the grey button, the slide handle to the desired position. WARNING: Use the 5-point harness to restrain the child while in the stroller at all times. Adjust harness to fit child securely. Catalyst Instruction Manual 7 INFANT MODE CombiUSA.com SETUP STEP 1: Lift rear lever firmly and completely. STEP 2: Shift seat to a horizontal position. STEP 3: Unlatch secure buckle strap located under STEP 4: Gently press down on the leg rest to the foot rest. complete the conversion to Infant Position. WARNING Remove child before removing or adjusting seat. 8 Catalyst Instruction Manual DO NOT carry seat by Bumper Bar STROLLER OPERATION FOLD STROLLER CombiUSA.com STEP 1: Activate the brake (Press downward on brake pedal) to prevent stroller from rolling forward while folding. STEP 2: Place handle in lowest position. STEP 3: Slide Folding Levers to release stroller frame. STEP 4: Lower stroller frame until locking mechanism engages on the left side of stroller. STEP 5: Gently lift stroller by handle to ensure locking mechanism is engaged. NOTE: When folding frame with seat attached, seat must be in forward facing and upright position. WARNING: To avoid finger entrapment or pinching, use care when folding and unfolding the stroller. Be certain the stroller is fully erected or folded, and locked in position before allowing your child near the stroller . Catalyst Instruction Manual 9 CAR SEAT ADAPTER INSTRUCTIONS CombiUSA.com Combi Car Seat Adapters are Compatible with the following infant car seats: Combi® Shuttle, Combi® Shuttle 33, Combi® Navette 22, Chicco® Key Fit® 30, Graco® SnugRide® 35 and Graco® SnugRide® 30. Instructions are slightly different for each manufacturer. *To attach an infant car seat: 1. Lock stroller wheels to prevent stroller movement. 2. Hold car seat above the mounting points on stroller. To attach car seat adaptor: Insert the posts on the sides of the car seat adapter into the slots of the frame. Push until you hear a “click” on both sides. 3. Push car seat downward onto the mounting points on stroller. Listen for the “click” to indicate the car seat is secured to the stroller. 4. Route car seat attachment remove car seat adaptor: To Pull inward on both red levers, then pull adapter upward. straps through the car seat’s vehicle belt path. (Refer to Car Seat Instruction Manual for additional information) 5. Pull upward on car seat to be sure car seat is secured to stroller. *Special Instruction for Combi® Shuttle Car Seat: Insert the rear portion of Shuttle car seat into the car seat adaptor as shown on the right. Align the orange tabs on each side of the Shuttle car seat with the red arrow on the car seat adaptor. Push down on the front portion of the Shuttle car seat. Listen for the audible “click” to indicate proper insertion of the car seat. Pull upward on car seat to be sure car seat is secured to stroller. Route the car seat attachment straps through the car seat vehicle belt path. NOTE: You must ALWAYS use the safety belt to secure the car seat. Always pull upward on the car seat to ensure that it is secure before routing the car seat attachment straps. If the seat is not secured to the car seat adaptor, then remove the car seat and re-start. 10 Catalyst Instruction Manual CAR SEAT ADAPTER INSTRUCTIONS CombiUSA.com *Special Instruction for Chicco® KeyFit Car Seat: Insert the rear portion of car seat into the car seat adaptor as shown on the right. Push down on the front portion of the car seat. Pull upward on car seat to be sure car seat is secured to stroller. The car seat attachment straps connected to the car seat adaptor must be placed over the seat. Routing the car seat attachment straps through the car seat vehicle belt path is not required. *Special Instruction for Graco® Snug Ride Seat: Hook the rear portion of the seat onto the car seat adaptor as shown on the right. Push down on the front portion of the car seat to ensure that the two metal U-shaped brackets at the bottom of the seat are secured onto the plastic hooks on the car seat adaptor. Pull upward on car seat to be sure car seat is secured to stroller. Route the car seat attachment straps through the car seat vehicle belt path. ROUTINE MAINTENANCE Store in a cool and dry area, especially in the summer. To avoid damaging stroller, NEVER place items on top of stroller during storage. Canopy, Restraint System, and Basket: Hand wash with a soft bristle brush. Wipe out excess water with a dry cloth and allow to dry in a shaded area. For stubborn dirt, dilute a mild detergent with warm water and apply directly to the dirty area. Wipe away the detergent with a warm, damp cloth. Stroller Frame Briskly wipe off any mud and dirt. To clean the frame, wipe with a damp cloth then wipe out any traces of moisture on the frame with a dry cloth. Excessive exposure to the sun could cause premature color fading of stroller plastic and fabric. Wheel Assemblies: After prolonged normal use, the wheels of your stroller may not swivel or turn as easily as when the stroller was new. This is usually due to a buildup of dirt in the swivel mechanism. Before adding lubrication, remove the swivel wheels by pressing in the release button, then wipe off mud and dirt. Do not use soap and water to wash wheels. Periodically check that all screws, bolts and nuts are tight. Avoid lubricating the swivel wheels whenever possible. Excessive lubrication or adding lubricant to swivel wheels when new may cause them to develop a shimmy or wobble that may quicken their deterioration. Add silicone* to the wheel assemblies in small amounts. Do not use oil-based lubricants because oil attracts dust and would hinder the movement rather than improve it. *Silicone spray is available at most hardware stores. CLEANING THE SEAT Hand Wash Do Not Use Bleach Dry Flat Do Not Iron Do Not Dry Clean Catalyst Instruction Manual 11 ROUTINE MAINTENANCE CombiUSA.com REMOVING SEAT SEAT BELT REMOVAL STEP 1: Remove the canopy (Refer to Canopy Installation) STEP 1: Route shoulder belt retainer at the rear of the seat through the slot. STEP 2: Unfasten the snaps (x12) around the edge of seat frame. Unfasten the snaps (x3) under the seat. STEP 2: Detach adjustment clip from the 5-point harness. STEP 3: Unfasten Velcro® straps located near the footrest on the seat frame. Follow the above direction in reverse to assemble STEP 4: Remove the lap portion of the harness straps. Combi USA, Inc. 12 Catalyst Instruction Manual 3520 Westinghouse Blvd., Suite B • Charlotte, NC 28273 Customer Service 1.800.992.6624 10/12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:30 Instance ID : uuid:2f7a0d1d-10f6-d04f-8eec-ac9951334351 Document ID : adobe:docid:indd:c27f227f-1538-11e2-924f-f3f2a5a5808c Rendition Class : proof:pdf Derived From Instance ID : 90f54f06-f4d6-11e1-95ca-d807c258554d Derived From Document ID : adobe:docid:indd:90f54f05-f4d6-11e1-95ca-d807c258554d Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 300.00, 300.00, 300.00, 762.00, 762.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 762.00, 762.00, 762.00, 72.00 Manifest Placed Y Resolution : 300.00, 300.00, 300.00, 762.00, 762.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 762.00, 762.00, 762.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:89829A48DB8EE111B078C614E33ABAEE, uuid:2C1754A4858CE111AEED9A6FD7C43E06, uuid:56ADBE6FDB8EE111B078C614E33ABAEE, uuid:85CD5EEC3C15E211A6F3D7794F1B043A, uuid:8DCD5EEC3C15E211A6F3D7794F1B043A, uuid:C8B6416ABD8EE111B078C614E33ABAEE, uuid:802688E3C08EE111B078C614E33ABAEE, uuid:78E11DC2C08EE111B078C614E33ABAEE, uuid:4FEF6712C18EE111B078C614E33ABAEE, uuid:B76C8006C18EE111B078C614E33ABAEE, uuid:368AC17DC396E1119BDE9B625C495E2E, uuid:F0F0804F828CE111AEED9A6FD7C43E06, uuid:7DEF951F828CE111AEED9A6FD7C43E06, uuid:FBEA331DDC8EE111B078C614E33ABAEE, uuid:F5AA1F0F858CE111AEED9A6FD7C43E06, uuid:318AC17DC396E1119BDE9B625C495E2E, uuid:97918728848CE111AEED9A6FD7C43E06, uuid:1CB0F56CDC8EE111B078C614E33ABAEE, uuid:0C63E242DC8EE111B078C614E33ABAEE, uuid:21B0F56CDC8EE111B078C614E33ABAEE, uuid:82EF951F828CE111AEED9A6FD7C43E06, uuid:1634EF78C996E1119BDE9B625C495E2E, uuid:1961B048C28EE111B078C614E33ABAEE, uuid:16936195DB8EE111B078C614E33ABAEE, uuid:1B936195DB8EE111B078C614E33ABAEE, uuid:96C0478D1495E111B285F68A2D055F4D, uuid:C995BCA7DB8EE111B078C614E33ABAEE, uuid:877C6FC2DB8EE111B078C614E33ABAEE, uuid:EBF0804F828CE111AEED9A6FD7C43E06, uuid:B4CA7764DD8EE111B078C614E33ABAEE, uuid:ACCA7764DD8EE111B078C614E33ABAEE, uuid:F59EDF0ADD8EE111B078C614E33ABAEE, uuid:77F9F477C78EE111B078C614E33ABAEE, uuid:303C6C143D15E211A6F3D7794F1B043A, uuid:2A3C6C143D15E211A6F3D7794F1B043A, uuid:099A41D93E15E211A6F3D7794F1B043A, uuid:4b927de7-6fcc-a041-b50c-105cb4f65fa9 Manifest Reference Document ID : uuid:1DE6C69E3C15E211A6F3D7794F1B043A, uuid:6253E6F53B15E211A6F3D7794F1B043A, uuid:68707416C896E1119BDE9B625C495E2E, uuid:2F3C6C143D15E211A6F3D7794F1B043A, uuid:293C6C143D15E211A6F3D7794F1B043A, uuid:089A41D93E15E211A6F3D7794F1B043A, uuid:183FA1070096E111A444D17031C9044A Create Date : 2012:10:11 14:40:04-04:00 Modify Date : 2012:11:05 10:43:22-05:00 Metadata Date : 2012:11:05 10:43:22-05:00 Creator Tool : Adobe InDesign CS3 (5.0.4) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 12345 bytes, use -b option to extract) Format : application/pdf Producer : Adobe PDF Library 8.0 Trapped : False Page Count : 12 Creator : Adobe InDesign CS3 (5.0.4)EXIF Metadata provided by EXIF.tools