Communication Components CE-1819-125MC PCS Band Multi Carrier Cell Extender User Manual

Communication Components Inc PCS Band Multi Carrier Cell Extender Authority to Act as Agent to a TCB

a href="https://usermanual.wiki/Communication-Components" itemprop="url"> Communication Components >

User Manual

Communication Components, Inc. 89 Leuning Street Phone: 201-342-3338South Hackensack, NJ 07606 Fax: 201-342-3339 PCS Band Multi Carrier Cell Extender CCI Model Number CE-1819-125MC-XXXX USER’S GUIDE Product Description: Communication Components, Inc. PCS CDMA Multi-carrier Cell Extender improves the performance of CDMA Base Stations (BTS) in indoor and outdoor locations, allowing for cost efficient implementation of high capacity radio networks. By increasing both the downlink power and receive sensitivity, CCI’s Cell Extender increases the overall coverage area and improves the performance of the site. Operation Description: CCI’s Multi-channel CDMA Cell Extender is designed to improve overall site performance by boosting both forward and reverse link parameters in a balanced manner. The system is designed to provide 125 Watts of usable CDMA output power per sector antenna (63 W per sector antenna for Canada) and can serve up to three sectors with two feeder antennas per sector. As such, a CE-1819-125MC system used in six-carrier sector with 3 carriers per antenna can delivers 40 W per carrier (21 W per carrier for Canada). • CCI supplies Cell Extender cabinet that requires a dual 30A 208/240V breaker and two batteries for backup purposes. RF Connection Cell Extender cabinet must be bolted to the frame. • Connect Cell Extender input Tx/Rx and Rx ports (connectors type N located on the connectors plate inside of the main cabinet) with DO and D1 ports of BTS in the proper sector using two DIN-N jumpers.
• Connect Cell Extender output Tx/Rx and Rx ports (Bias-T blocks with DIN connectors located on the connectors plate inside of the main cabinet) with Tx/Rx and Rx ports of Main Lines of the proper sector using two DIN-DIN jumpers. AC Connection • 20A Breakers must be installed in the main electrical box (or A-box). • 3-conductor AC-wire gage 12-14 must be run through metal conduit to the electrical junction box inside of the CCI Cell Extender cabinet. The entry point to this junction box is from the bottom of the cabinet via a corrugated shield. • Run a standard 6 gauge grounding wire from the site’s main grounding bar (Bus-bar in the A-box) to the CCI Cell Extender cabinet and secure it to the electrical junction box inside the cabinet. • Run Alarm cable through 1” conduit to the alarm card in BTS. Site technician will make actual connection. • Install the batteries: a. Place the batteries in the bottom of the cabinet b. Use the short jumper to connect the positive terminal of one battery to the negative terminal of the other battery. c. Cover the battery terminals with the supplied terminal boots. • Confirm proper electrical connection a. Turn off all breakers on PSU modules located in the Cell Extender cabinet; b. Turn on breakers in the main electrical box (A-box) c. Confirm that the green Power LED on PSU’s turn on. Setting the RF Output Power on the CE-1819-125MC-XXXxX Cell Extender The RF output power is adjustable on the Cell Extender. Use Gain Control Block that contains a set of the input signal attenuators. The user must adjust the RF input power to the Cell Extender connecting the proper pad such that the combined RF output power level of any number of the individual carriers does not exceed the levels shown below in order for the RF output spectral emissions to be compliant with the FCC spurious emissions limit of -13 dBm outside of the assigned frequency block. These levels must not exceed Channel Center Frequency (MHz) Maximum RF 0utput (Watt)* Maximum RF 0utput for Canada (Watt) 1930-1990 125 63
Download:
Mirror Download [FCC.gov]
Document ID789403
Application IDqiqCdmNpUdvd0wgPvGMzhA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize18.13kB (226673 bits)
Date Submitted2007-05-07 00:00:00
Date Available2007-05-08 00:00:00
Creation Date2007-05-03 16:14:18
Producing SoftwareAcrobat Distiller 5.0.5 (Windows)
Document Lastmod2007-05-03 16:14:31
Document TitleAuthority to Act as Agent to a TCB:
Document CreatorAcrobat PDFMaker 5.0 for Word
Document Author: RUBY DULMAGE
FCC ID Filing: NT3CE-1819-125MC

Navigation menu