Compal Electronics TP00062BWD Digitizer I/O Device User Manual
Compal Electronics Inc Digitizer I/O Device Users Manual
Users Manual
Wacom Digitizer
Wacom Digitizer
Implementation Guide
Implementation Guide
Contents
1. Principle of Wacom EMR
2. General Specification
W Di iti U it
x
W
acom
Di
g
iti
zer
U
n
it
㼼
㼼
㼼㼼
㼻
x
x
x
3-1. Structure
x
3-2. Structure
x
4-1. Digitizer Lineup
x䡡䡡䡡
䡡䡡䡡
䡡䡡䡡
4-2. Digitizer Lineup
x
4-3. Digitizer Line up
x
䡡䡡䡡
䡡䡡䡡
4-4. Digitizer Lineup
x
4-5. Digitizer Lineup
5. Display Lineup
x䞉
6-1. Customizing Digitizer
xCondition for digitizer customization
6-2. Customizing Digitizer
xSensor Board Design
OK
NG
6-3. Customizing Digitizer
xSensor Board Design (continued)
6-4. Customizing Digitizer
xBaby Board Design
x
x
C t di iti DF19L
14P
1H (HIROSE) i l t
z
C
onnec
t
or on
di
g
iti
zer:
DF19L
-
14P
-
1H (HIROSE)
or equ
i
va
l
en
t
zCounterpart connector: DF19-14S-1S, DF19G-14S-1C (HIROSE) or
equivalent
6-5. Customizing Digitizer
Dl tShdl
x
D
eve
l
opmen
tS
c
h
e
d
u
l
e
No. Step Lead Time
1
1
2
3
3
4
5
6
7
7
8
8
9
7-1. System Designing
Prevention of EM noise problem
7-2. System Designing
B
EM Noise Countermeasure
B’
!
As far as you can,please
SEPARATE the Digitizer Unit
!
from the Inverter
7-3. System Designing
EM Noise Countermeasure2
7-4. System Designing
7-5. System Designing
8-1. System Designing2
Reduction of metal influence
8-2. System Designing2
8-3. System Designing2
8-4. System Designing2
9-1. System Calibration
x
x
x
x
9-2. System Calibration
x
9-3. System Calibration
x
x
x
9-4. System Calibration
x
x
x
x
9-5. System Calibration
x
9-6. System Calibration
xBefore sending calibration machine, please check
below items.
xNote:
x
x
10. Driver
xDevice Driver
x
Note:
x
Note:
x
10. Driver
xDevice Driver
x
Note:
x
Note:
x
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
® Reorient or relocate the receiving antenna.
® Increase the separation between the equipment and receiver.
® Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
® Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any interference received, including interference
that may cause undesired operation
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
The system integrated this radio module should have similar label to indicate contains approved RF module.
Label such as “ Contains FCC ID: GKR-TP00062BWD , IC : 2533B-TP00062BWD “.
This radio should not be installed and operated simultaneously with other radios.