Computime CTL35XXA Module User Manual

Computime Ltd. Module

User manual

Download: Computime CTL35XXA Module User Manual
Mirror Download [FCC.gov]Computime CTL35XXA Module User Manual
Document ID2708532
Application IDJ+iSENZSSEgiGQKSLPz01Q==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize20.88kB (260990 bits)
Date Submitted2015-08-09 00:00:00
Date Available2015-08-09 00:00:00
Creation Date2015-08-09 20:21:04
Producing SoftwareAcrobat Distiller 9.0.0 (Windows)
Document Lastmod2015-08-09 20:21:04
Document Titleuser manual.pdf
Document CreatorAcrobat PDFMaker 11 Word 版
Document Author: COMPUTIME

ZigBee-Ready RF Transceiver Module
(IEEE 802.15.4)
CTL3585
The reproduction of this datasheet is NOT allowed without approval of Computime Limited. All information and data
contained in this datasheet are subject to change without notice. This publication supersedes and replaces all information
previously supplied. Computime has no responsibility to the consequence of using the information described in this
document.
Copyright © 2015 Computime Limited. All rights reserved.
Rev.1
ZigBee- Ready RF Transceiver Module CTL3585
Revision
Rev.
Date
(DD-MM-YYYY)
21-1-2015
History
First Released
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
Table of Contents
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
General Description...................................................................................................................................... 1
Applications .................................................................................................................................................. 1
Features ....................................................................................................................................................... 1
Absolute Maximum Ratings.......................................................................................................................... 2
Recommended Operating Conditions .......................................................................................................... 2
Electrical Specifications................................................................................................................................ 2
Typical application block .............................................................................................................................. 3
Pin Assignment............................................................................................................................................. 4
Pin Description ............................................................................................................................................. 5
Block Diagram........................................................................................................................................... 9
RF Frequency Detail ............................................................................................................................... 10
PCB Layout Recommendations.............................................................................................................. 11
Mechanical Dimensions.......................................................................................................................... 12
Copyright © 2015 Computime Limited. All rights reserved.
Rev.1
ZigBee- Ready RF Transceiver Module CTL3585
1. General Description
The CTL3585 are compact surface mounted High Power Wireless RF Transceiver Module
specially designed for Ember ZigBee™ protocol stack for wireless networks, EmberZNet, based on
IEEE 802.15.4 standard in the 2.4GHz world-wide ISM band. The size of CTL3514 is 19.2 x 16 x
2.8 mm and the size of CTL3585 is 23.5x16 x2.8mm.It integrated a 2.4GHz, IEEE 802.15.4-2003
compliant transceiver with a 32-bit network processor (ARM Cortex-M3 Processor) to run
EmberZNet. It contains embedded FLASH and integrated RAM for program and data storage. It
utilizes the non-intrusive SIF module for powerful software debugging and programming of the
network processor.
2. Applications
Home
automation &
building control
Home
appliances &
alarms
Monitoring of
remote
systems
Security
systems &
lighting
controls
Sensor data
capture in
embedded
networks
3. Features
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Complete ZigBee-ready module with integrated PCB antenna
Integrated IEEE 802.15.4 PHY and MAC layer
Non-intrusive debug interface (SIF)
SPI interface for communication and controlled by the Host using the EmberZNet Serial Protocol
(EZSP)
Internal RC oscillator for timer
High performance direct sequence spread spectrum (DSSS) RF transceiver
16 channels in the 2.4 GHz ISM band
On-chip regulator for 2.1-3.6V operation.
Three deep low power modes
32-bit ARM® Cortex™-M3 processor
192KB FLASH ROM and 12KB RAM(EM357 internal)
+20dBm Max. transmission power
-100dBm sensitivity
Small footprint: 23.5x16x2.8mm
Extremely low Deep Sleep Current.
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
4. Absolute Maximum Ratings
Parameter
Test Conditions
Min.
Max.
Unit
Regulator input voltage (VDD_PADS)
-0.3
+3.6
Voltage on any GPIO (PA[7:0], PB[7:0],
PC[7:0]),
SWCLK,
nRESET,
VREG_OUT
-0.3
VDD_PADS
+0.3
Voltage on any GPIO pin (PA4, PA5, PB5,
PB6, PB7, PC1), when used as an input to the
general purpose ADC with the low voltage
range selected
-0.3
2.0
Voltage on OSCA, OSCB, NC
-0.3
VDD_PADSA
+0.3
Storage temperature
-40
+85
°C
5. Recommended Operating Conditions
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
Regulator input voltage (VDD_PADS)
2.1
3.6
Operating temperature range
-40
+85
°C
Max
Unit
2.48
GHz
MSL3
Moisture Sensitivity Level(MSL)
6. Electrical Specifications
T=25ć, VCC = 3.0V, Fo =2450MHz, if nothing else stated.
Parameter
Condition / Note
Min
Typ.
RF Operating frequency
Programmable in 5MHz steps, 5 MHz
steps for IEEE 802.15.4 compliance
Number of channels
For IEEE 802.15.4 compliance
16
Channel spacing
For IEEE 802.15.4 compliance
2.405
Frequency stability
MHz
+/-40
ppm
+20
dBm
Transmit power
Programmable from firmware
Sensitivity
PER = 1% PER, 20byte packet
defined by IEEE 802.15.4 Boost
mode
-100
dBm
Adjacent channel rejection +/-5 MHz
IEEE 802.15.4 compliance at -82
dBm
35/35
dB
Adjacent channel rejection +/-10 MHz
IEEE 802.15.4 compliance at -82
dBm
40/40
dB
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
Parameter
Condition / Note
Min
Supply voltage
Typ.
2.1
Current consumption,
RX mode
Max
Unit
3.6
Max RX sensitivity (normal mode)
28
mA
Max RX sensitivity (boost mode)
30
mA
Current
consumption,
TX mode
CTL3585
190
mA
Deep sleep current
CTL3585
2.8
uA
512
KB
24
MHz
32.768
KHz
Flash Memory
FLASH memory in EM3585
MCU clock frequency
External crystal or Ext 32.768KHz
clock
MCU Low Speed Clock
7. Typical application block
HOST
MCU
VDD_PADS=2.1- 3.6V
NREST
PTI_EN
Debug and
PTI-DATA
programming
SIF_CLK
interface
CTL3585
RF Module
LINK_ACTIVITY
SIF-MISO
SIF-MOSI
NSIF LOAD
32.768 kHz CL=12.5 pF
Figure 1: Example of application circuit
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
8. Pin Assignment
Pin 8
Pin 9
Pin 1
Pin 18
Pin 1
Pin 18
Figure 2: CTL3585 pin assignment
Copyright © 2015 Computime Limited. All rights reserved.
Pin 29
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
9. Pin Description
Pin#
CTL3585
Direction
Description
PB0
I/O
Digital I/O
VREF
Analog O
ADC reference output
VREF
Analog I
ADC reference input
IRQA
External interrupt source A
TRACECLK
Synchronous CPU trace clock
TIM1CLK
Timer 1 external clock input
TIM2MSK
Timer 2 external clock mask input
NC
NC
PC0
I/O High
current
JRST
JTAG reset input from debugger
IRQD
Default external interrupt source D
TRACEDATA1
Synchronous CPU trace data bit 1
PB7
I/OHigh current
ADC2
Analog
IRQC
Default external interrupt source C
TIM1C2
Timer 1 channel 2 output
TIM1C2
Timer 1 channel 2 input
PB6
I/O High
current
Digital I/O
ADC1
Analog
ADC input 1
IRQB
External interrupt source B
TIM1C1
Timer 1 channel 1 output
TIM1C1
Timer 1 channel 1 input
NC
Digital I/O Either Enable with GPIO_DBGCFG[5]
Digital I/O
ADC input 2
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
Pin#
CTL3585
Direction
Description
PB5
I/O
Digital I/O
ADC0
Analog
TIM2CLK
Timer 2 external clock input
TIM1CLK
Timer 1 external clock mask input
ADC input 0
GND
GND
NC
NC
10
nRESET
PC6
I/O
Digital I/O
OSC32B
I/O
32.768KHz crystal oscillator.
NTX_ACTIVE
Inverted TX_ACTIVE signal
PC7
I/O
Digital I/O
OSC32A
I/O
32.768KHz crystal oscillator.
OSC32_EXT
VDD_PADS
Power
PA7
I/O High current
TIM1C4
Timer 1 channel 4 output
TIM1C4
Timer 1 channel 4 input
REG_EN
External regulator open drain output
PB3
I/O
Digital I/O
TIM2C3
Timer 2 channel 3 output
TIM2C3
Timer 2 channel 3 input
SC1nCTS
UART CTS handshake of Serial Controller 1
SC1SCLK
SPI master clock of serial Controller 1
SC1SCLK
SPI slave clock of serial Controller 1
11
12
13
NC
Active low chip reset(internal pull-up)
Digital 32.768KHz clock input source
Pads supply(2.1-3.6V)
Digital I/O Disable REG_EN with GPIO_DBGCFG [4]
14
15
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
Pin#
16
17
CTL3585
Direction
Description
PB4
I/O
Digital I/O
TIM2C4
Timer 2 channel 4 output
TIM2C4
Timer 2 channel 4 input
SC1nRTS
UART RTS handshake of serial controller 1
SC1nSSEL
SPI slave select of serial controller 1
PA0
I/O
Digital I/O
TIM2C1
Timer 2 channel 1 output
TIM2C1
Timer 2 channel 1 input
SC2MOSI
SPI master data out of serial controller 2
SC2MOSI
SPI slave data in of serial controller 2
PA1
I/O
Digital I/O
TIM2C3
Timer 2 channel 3 output
TIM2C3
Timer 2 channel 3 input
SC2SDA
I/O
TWI data of serial controller 2
SC2MISO
SPI slave data out of serial controller 2
SC2MISO
SPI master data in of serial controller 2
PA2
I/O
Digital I/O
TIM2C4
Timer 2 channel 4 output
TIM2C4
Timer 2 channel 4 input
SC2SCL
I/O
TWI clock of serial controller 2
SC2SCLK
SPI master clock of serial controller 2
SC2SCLK
SPI slave clock of serial controller 2
PA3
I/O
SC2Nssel
SPI slave select of serial controller 2
TIM2C2
Timer 2 channel 2 output
TIM2C2
Timer 2 channel 2 input
18
19
Digital I/O
20
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
Pin#
CTL3585
Direction
Description
PA4
I/O
Digital I/O
ADC4
Analog
PTI_EN
Frame signal of packet trace interface
TRACEDATA2
Synchronous CPU trace data bit 2
PA5
I/O
Digital I/O
ADC5
Analog
PTI_DATA
Data signal of packet trace interface
NBOOTMODE
Embedded serial bootloader activation out of reset
TRACEDATA3
Synchronous CPU trace data bit 3
PA6
I/O High current
TIM1C3
Timer 1 channel 3 output
TIM1C3
Timer 1 channel 3 input
PB1
I/O
Digital I/O
SC1MISO
SPI slave data out of serial controller 1
SC1MOSI
SPI master data out of serial controller 1
SC1SDA
I/O
TWI data of serial controller 1
SC1TXD
UART transmit data of serial controller 1
TIM2C1
Timer 2 channel 1 output
TIM2C1
Timer 2 channel 1 input
PB2
I/O
SC1MISO
SPI master data in of serial controller 1
SC1MOSI
SPI slave data in of serial controller 1
SC1SCL
I/O
SC1RXD
UART receive data of serial controller 1
TIM2C2
Timer 2 channel 2 output
TIM2C2
Timer 2 channel 2 input
JTCK
JTAG clock input from debugger
SWCLK
I/O
ADC input 4
21
22
23
24
25
ADC input 5
Digital I/O
Digital I/O
TWI clock of serial controller 1
26
Serial Wire Clock input/output with debugger
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
Pin#
CTL3585
Direction
Description
PC2
I/O
Digital I/O Enable with GPIO_DBGCFG[5]
JTDO
JTAG data out to debugger
SWO
Serial Wire Output asynchronous trace output to debugger
TRACEDATA0
Synchronous CPU trace data bit3
PC3
I/O
Digital I/O Enable with GPIO_DBGCFG[5]
JTDI
JTAG data in from debugger
TRACECLK
Synchronous CPU trace clock
PC4
I/O
Digital I/O Either Enable with GPIO_DBGCFG[5]
JTMS
SWDIO
I/O
27
28
29
JTAG mode select from debugger
Serial Wire bidirectional data to/from debugger
10. Block Diagram
2.1 – 3.6V
PCB antenna
32 Bit ARM Processor
User
Application
UART/SPI/I2C
Communication
24MHz
FEM
TM
Zigbee
Network
IEEE 802.15.4
RF Transceiver
IEEE 802.15.4
MAC
CTL3585
Figure 3: Block Diagram
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
11. RF Frequency Detail
The following table shows the RF channels as defined by the IEEE 802.15.4 standard.
RF channel
Frequency
11
2405MHz
12
2410MHz
13
2415MHz
14
2420MHz
15
2425MHz
16
2430MHz
17
2435MHz
18
2440MHz
19
2445MHz
20
2450MHz
21
2455MHz
22
2460MHz
23
2465MHz
24
2470MHz
25
2475MHz
26
2480MHz
The use of RF frequencies and maximum allowed RF power should according to different national
regulations. The CTL3585 are complying with the applicable regulations for the world wide 2.4GHz
ISM band.
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
12. PCB Layout Recommendations
Please reference Mechanical Dimensions shown in next section for PCB layout.
The area underneath the module should be covered with solder mask in order to prevent short
circuit on the test pads on the back side of the module. A solid ground plane under the module is
preferred.
As the module integrated with onboard PCB trace antenna, the mounting position of the module will
have great impact on the RF performance. There should not be any trace, ground plane or metal
part underneath or nearby the area of the onboard PCB trace antenna. The figure below shows an
example how the module positioned on the mother PCB.
Figure 4: A recommended placement of the module on a main PCB
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
13. Mechanical Dimensions
Figure 5: Mechanical Dimensions of CTL3585
Figure 5: Mechanical Dimensions of CTL3585
For further details on the SoC transceiver (Ember EM351), please consult the data sheet at
http://www.ember.com
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
Contact information
COMPUTIME CORPORATE HQ
9/F Tower One, Lippo Centre,
89 Queensway,
Hong Kong
Tel: +852.2260.0300
Fax: +852.2790.3996
e-mail: hq@computime.com
COMPUTIME NORTH AMERICA HQ,
4700 Duke Dr.
Suite 200
Mason OH 45040
USA
Tel: +1(513).398.2579
Fax: +1(513).754.8955
e-mail: na@computime.com
Cincinnati Technologies
4700 Duke Dr.
Suite 200
Mason OH 45040
USA
Tel: +1(513).754.8935
Fax: +1(513).754.8955
e-mail: ctws@computime.com
About Computime
Founded in 1974, Computime is a global technology, brand and manufacturing company
providing innovative automation and control solutions to customers in commercial, industrial
and consumer markets.
The Company provides technologies and products that save energy and make people's
lives more productive and comfortable.
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
Regulatory Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
The devices must be installed and used in strict accordance with the instructions as
device may not cause harmful interference, and (2) this device must accept any interference received, including
described in the user documentation that comes with the product.
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
If the
FCC identification
number is not visible when the module is installed inside another
FCC
Radiation
Exposure Statement
device,
then
of integrated
the device
into which
module
is installed
must also
display
The
modular
canthe
be outside
installed or
in mobile
or fix the
devices
only. This
modular cannot
be installed
in any
portable
device, fortoexample,
USB dongle
like transmitters is forbidden.
label referring
the enclosed
module.
This
withuse
FCC wording
RF radiation
exposure
set forth for an uncontrolled environment. This
Thismodular
exteriorcomplies
label can
such
as thelimits
following:
transmitter
not be co-located
or operating
in conjunction with any other antenna or transmitter. This
“Containsmust
Transmitter
Module FCC
ID: 2AAUQ-CTL35XXA”
modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.
If the FCC identification number is not visible when the module is installed inside another device, then the outside
of the device into which the module is installed must also display a label referring to the enclosed module. This
When the module is installed inside another device, the user manual of this device must
exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2AAUQ-CTL35XXA Or
contain below warning statements:
Contains FCC ID: 2AAUQ-CTL35XXA ā
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
when the module is installed inside another device, the user manual of this device must contain below warning
two conditions:
statements;
(1)
This
device
may
notPart
cause
interference,
(2)toThis
device must
accept any
1.
This
device
complies
with
15 of harmful
the FCC Rules.
Operation isand
subject
the following
two conditions:
interference
received,
interference that may cause undesired operation.
(1)
This device may
not causeincluding
harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2.
Changes or
not expressly
approved
by the party
for compliancefor
could
void the user's
Changes
ormodifications
modifications
not expressly
approved
by responsible
the party responsible
compliance
authority
to operate
the equipment.
could void
the user's
authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the
user
that be
comes
with theinproduct
Thisdocumentation
modular could
installed
the fix or mobile devices only, installed in the portable
device, like USB dongle is forbidden. This modular complies with FCC RF radiation
exposure limits set forth for an uncontrolled environment. This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. This modular must
be installed and operated with a minimum distance of 20 cm between the radiator and user
body.
For manufacturer:
The end product into which the module will be installed should be the fix or mobile devices
only, the portable device, like USB dongle is forbidden.
The end product into which the module will be installed should be installed and operated
with a minimum distance of 20 cm between the radiator and user body.
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1
ZigBee- Ready RF Transceiver Module CTL3585
IC Statement:
This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to
the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son
fonctionnement est soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent
causer un mauvais fonctionnement de l'appareil.
IC Radiation Exposure Statement
The modular can be installed or integrated in mobile or fix devices only. This modular
cannot be installed in any portable device, for example, USB dongle like transmitters is
forbidden.
This modular complies with IC RF radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This modular must be installed and operated with a minimum
distance of 20 cm between the radiator and user body. Cette modulaire doit être installé et
utilisé à une distance minimum de 20 cm entre le radiateur et le corps de l'utilisateur.
If the IC number is not visible when the module is installed inside another device, then the
outside of the device into which the module is installed must also display a label referring to
the enclosed module. This exterior label can use wording such as the following: “Contains
IC: 1700A-CTL35XXA”
when the module is installed inside another device, the user manual of this device must
contain below warning statements;
1. This device complies with Industry Canada's licence-exempt RSSs. Operation is subject
to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
2. Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada . Son
fonctionnement est soumis aux deux conditions suivantes :
( 1 ) Ce dispositif ne peut causer d'interférences ; et
( 2 ) Ce dispositif doit accepter toute interférence , y compris les interférences qui peuvent
causer un mauvais fonctionnement de l'appareil.
The devices must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the product
Copyright © 2015 Computime Limited. All rights reserved.
Rev. 1

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : COMPUTIME
Create Date                     : 2015:08:09 20:21:04+08:00
Modify Date                     : 2015:08:09 20:21:04+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Metadata Date                   : 2015:08:09 20:20:44+08:00
Creator Tool                    : Acrobat PDFMaker 11 Word 版
Document ID                     : uuid:e220a8c7-66b7-4f38-9e43-694a9f46f1b0
Instance ID                     : uuid:d5d4286a-fc0e-4b4a-a2e3-87b7953c8cac
Subject                         : 21
Format                          : application/pdf
Creator                         : COMPUTIME
Title                           : user manual.pdf
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Source Modified                 : D:20150805030803
Company                         : COMPUTIME
Tag Ad Hoc Review Cycle ID      : -1172179898
Tag Email Subject               : MARS SPECIFICATION
Tag Author Email                : esoder@core.com
Tag Author Email Display Name   : ernie soderlund
Tag Reviewing Tools Shown Once  : 
Page Count                      : 18
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2AAUQ-CTL35XXA

Navigation menu