Comtrend NL3240U Wireless Gateway User Manual 1

Comtrend Corporation Wireless Gateway 1

Contents

User Manual-1

 NNWU     NexusNexusWAP-User      sLinksLink5895Manuk 324k 3125ua, ual 40u, 20ua,WR-6    Nexu, Nex6895usLinxusLi5 k 32nk 3 40, 120,
   1 Preface    This manual provides information related to the installation and operation of this device.  The individual reading this manual is presumed to have a basic understanding of telecommunications terminology and concepts.    If you find the product to be inoperable or malfunctioning, please contact technical support for immediate service by email at INT-support@comtrend.com    For product update, new product release, manual revision, or software upgrades, please visit our website at http://www.comtrend.com   Important Safety Instructions  With reference to unpacking, installation, use, and maintenance of your electronic device, the following basic guidelines are recommended:  •  Do not use or install this product near water, to avoid fire or shock hazard.  For example, near a bathtub, kitchen sink or laundry tub, or near a swimming pool.  Also, do not expose the equipment to rain or damp areas (e.g. a wet basement). •  Do not connect the power supply cord on elevated surfaces.    Allow it to lie freely.   There should be no obstructions in its path and no heavy items should be placed on the cord.  In addition, do not walk on, step on, or mistreat the cord. •  Use only the power cord and adapter that are shipped with this device. •  To safeguard the equipment against overheating, make sure that all openings in the unit that offer exposure to air are not blocked. •  Avoid using a telephone (other than a cordless type) during an electrical storm.  There may be a remote risk of electric shock from lightening.  Also, do not use the telephone to report a gas leak in the vicinity of the leak. •  Never install telephone wiring during stormy weather conditions.   CAUTION:   To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.   Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.     WARNING   Disconnect the power line from the device before servicing.    Power supply specifications are clearly stated in Appendix C - Specifications.
   2 FCC & ISED  User Information  Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.  Aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur.  Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:  —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected. —Consult the dealer or an experienced radio/TV technician for help.  This Class B digital apparatus complies with Canadian ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s).  Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device.  Cet appareil numérique de la classe B est conforme à la norme NMB-003 Canada. Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie.  Cet appareil est conforme à la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne peut pas provoquer d’interférences et 2. Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.
   3 Radiation Exposure  FCC ID: L9VNL3240U IC: 4013C-NL3240U US: 5SYDL01ANL3240U REN: 0.1A  FCC  1. This Transmitter must not be colocated or operating in conjunction with any other antenna or transmitter.  2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.  ISED  This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et votre corps. Cet émetteur ne doit pas être co-localisées ou opérant en conjonction avec une autre antenne ou transmetteur.  Operations in the 5.15-5.25Ghz band are restricted to indoor usage only.  Le fonctionnement sur la bande 5,15–5,25Ghz est limité à une utilisation intérieure uniquement.  This radio transmitter (identify the device by certification number) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.  Model Name: AN2450-64D03BBF Type: External Gain:  2.4G: 1.2 dBi 5G: 2.5 dBi  Model Name: AN2450-64D02BBF Type: External Gain:
   4 2.4G: 2.5 dBi 5G: 2.5 dBi  The REN statement is the following: "The Ringer Equivalence Number (REN) indicates the maximum number of devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed five."  Copyright Copyright©2016 Comtrend Corporation.  All rights reserved.  The information contained herein is proprietary to Comtrend Corporation.    No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of Comtrend Corporation.  This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.  This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for more details.  You should have received a copy of the GNU General Public License along with this program.  If not, see http://www.gnu.org/licenses/      NOTE:   This document is subject to change without notice.   Protect Our Environment This symbol indicates that when the equipment has reached the end of  its useful life, it must be taken to a recycling centre and processed  separate from domestic waste.  The cardboard box, the plastic contained in the packaging, and the parts that make up this router can be recycled in accordance with regionally established regulations.  Never dispose of this electronic equipment along with your household waste; you may be subject to penalties or sanctions under the law.  Instead, please be responsible and ask for disposal instructions from your local government.
   5 Table of Contents  CHAPTER 1 INTRODUCTION ........................................................................................................... 8CHAPTER 2 INSTALLATION ............................................................................................................. 92.1 HARDWARE SETUP ........................................................................................................................... 92.2 LED INDICATORS .......................................................................................................................... 11CHAPTER 3 WEB USER INTERFACE ............................................................................................ 133.1 DEFAULT SETTINGS ....................................................................................................................... 133.2 IP CONFIGURATION ........................................................................................................................ 143.3 LOGIN PROCEDURE ........................................................................................................................ 16CHAPTER 4 DEVICE INFORMATION ........................................................................................... 184.1 WAN ............................................................................................................................................. 194.2 STATISTICS ..................................................................................................................................... 204.2.1LAN Statistics ................................................................................................................. 204.2.2WAN Service ................................................................................................................... 214.2.3XTM Statistics ................................................................................................................. 224.2.4xDSL Statistics ................................................................................................................ 234.3 ROUTE ........................................................................................................................................... 284.4 ARP............................................................................................................................................... 294.5 DHCP ........................................................................................................................................... 294.6 NAT SESSION ................................................................................................................................ 314.7 IGMP INFO .................................................................................................................................... 324.8 IPV6 .............................................................................................................................................. 334.8.1 IPv6 Info ................................................................................................................................ 334.8.2 IPv6 Neighbor ....................................................................................................................... 344.8.3 IPv6 Route ............................................................................................................................. 354.9 CPU & MEMORY ........................................................................................................................... 364.10 NETWORK MAP ........................................................................................................................... 374.11 WIRELESS .................................................................................................................................... 374.11.1 Station Info ........................................................................................................................... 374.11.2 Site Survey............................................................................................................................ 39CHAPTER 5 BASIC SETUP ............................................................................................................... 405.1 WAN SETUP ................................................................................................................................... 415.1.1 WAN Service Setup ................................................................................................................ 425.2 NAT .............................................................................................................................................. 435.2.1Virtual Servers ................................................................................................................ 435.2.2Port Triggering ............................................................................................................... 455.2.3DMZ Host ....................................................................................................................... 475.2.4    IP Address Map............................................................................................................... 485.2.5    ALG/Pass-Through ......................................................................................................... 495.3 LAN .............................................................................................................................................. 505.3.1 LAN IPv6 Autoconfig ............................................................................................................. 535.3.2 Static IP Neighbor ................................................................................................................. 565.3.3 UPnP ..................................................................................................................................... 575.4 WIRELESS ...................................................................................................................................... 585.4.1 Basic 2.4GHz ......................................................................................................................... 585.4.2 Security 2.4GHz ..................................................................................................................... 605.4.3 Basic 5GHz ............................................................................................................................ 625.4.4 Security 5GHz ........................................................................................................................ 635.5 PARENTAL CONTROL ..................................................................................................................... 645.5.1Time Restriction .............................................................................................................. 645.5.2URL Filter ....................................................................................................................... 655.6 HOME NETWORKING ...................................................................................................................... 675.6.1 Print Server ........................................................................................................................... 675.6.2 DLNA ..................................................................................................................................... 675.6.3 Storage Service ...................................................................................................................... 685.6.4 USB Speed ............................................................................................................................. 69
   6 CHAPTER 6 ADVANCED SETUP ..................................................................................................... 706.1 AUTO-DETECTION SETUP ............................................................................................................... 706.2 SECURITY ...................................................................................................................................... 756.2.1IP Filtering ..................................................................................................................... 756.2.2    MAC Filtering ................................................................................................................. 796.3 QUALITY OF SERVICE (QOS) ..........................................................................................................  816.3.1QoS Queue ...................................................................................................................... 826.3.1.1QoS Queue Configuration .............................................................................................. 826.3.1.2Wlan Queue .................................................................................................................... 866.3.2    QoS Classification .......................................................................................................... 876.3.3    QoS Port Shaping ........................................................................................................... 896.4 ROUTING ....................................................................................................................................... 906.4.1Default Gateway ............................................................................................................. 906.4.2Static Route ..................................................................................................................... 916.4.3Policy Routing ................................................................................................................ 926.4.4RIP .................................................................................................................................. 936.5 DNS .............................................................................................................................................. 946.5.1DNS Server ..................................................................................................................... 946.5.2Dynamic DNS ................................................................................................................. 956.5.3    DNS Entries .................................................................................................................... 966.5.4    DNS Proxy/Relay ............................................................................................................ 976.6 DSL ............................................................................................................................................... 986.7 DSL BONDING ............................................................................................................................... 996.8 INTERFACE GROUPING ................................................................................................................. 1006.9 IP TUNNEL ................................................................................................................................... 1036.9.1 IPv6inIPv4 ........................................................................................................................... 1036.9.2 IPv4inIPv6 ........................................................................................................................... 1046.10 CERTIFICATE .............................................................................................................................. 1056.10.1Local ............................................................................................................................. 1056.10.2Trusted CA .................................................................................................................... 1076.11 POWER MANAGEMENT .............................................................................................................. 1086.12 MULTICAST ............................................................................................................................... 1096.13 WIRELESS .................................................................................................................................. 1116.13.1 Basic 2.4GHz ..................................................................................................................... 1116.13.2 Security 2.4GHz ................................................................................................................. 1136.13.3 WPS 2.4GHz ...................................................................................................................... 1166.13.4 MAC Filter 2.4GHz ........................................................................................................... 1196.13.5 Wireless Bridge 2.4GHz ..................................................................................................... 1216.13.6 Advanced 2.4GHz .............................................................................................................. 1226.13.7 Basic 5GHz ........................................................................................................................ 1256.13.8 WPS 5GHz ......................................................................................................................... 1266.13.9 MAC Filter 5GHz .............................................................................................................. 1286.13.10 Advanced 5GHz ............................................................................................................... 129CHAPTER 7 VOICE .......................................................................................................................... 1307.1 SIP BASIC SETTING – GLOBAL PARAMETERS ............................................................................... 1317.2 SIP BASIC SETTING – SERVICE PROVIDER ................................................................................... 1327.3 SIP ADVANCED SETTING – GLOBAL PARAMETERS ....................................................................... 1357.4 SIP ADVANCED SETTING – SERVICE PROVIDER ........................................................................... 1367.5 SIP DEBUG SETTING – GLOBAL PARAMETERS ............................................................................. 1397.6 SIP DEBUG SETTING – SERVICE PROVIDER .................................................................................. 1407.7 TELEPHONE CALLS ...................................................................................................................... 141CHAPTER 8 DIAGNOSTICS ........................................................................................................... 1438.1 DIAGNOSTICS – INDIVIDUAL TESTS ............................................................................................. 1438.2 ETHERNET OAM ......................................................................................................................... 1448.3 UPTIME STATUS ........................................................................................................................... 1468.4 PING ............................................................................................................................................ 1478.5 TRACE ROUTE ............................................................................................................................. 148CHAPTER 9 MANAGEMENT ........................................................................................................ 1499.1 SETTINGS ..................................................................................................................................... 149
   7 9.1.1Backup Settings ............................................................................................................. 1499.1.2Update Settings ............................................................................................................. 1509.1.3Restore Default ............................................................................................................. 1509.2 SYSTEM LOG ............................................................................................................................... 1529.3 SNMP AGENT ............................................................................................................................. 1549.4 TR-069 CLIENT ........................................................................................................................... 1559.5 INTERNET TIME ........................................................................................................................... 1579.6 ACCESS CONTROL ....................................................................................................................... 1589.6.1  Accounts ........................................................................................................................... 1589.6.2  Services ............................................................................................................................. 1609.6.3  IP Address ......................................................................................................................... 1619.7 WAKE-ON-LAN ........................................................................................................................... 1629.8 UPDATE SOFTWARE ..................................................................................................................... 1639.9 REBOOT ....................................................................................................................................... 164CHAPTER 10 LOGOUT ................................................................................................................... 165APPENDIX A - FIREWALL ............................................................................................................. 166APPENDIX B - PIN ASSIGNMENTS .............................................................................................. 169APPENDIX C – SPECIFICATIONS ................................................................................................ 170APPENDIX D - SSH CLIENT .......................................................................................................... 172APPENDIX E - PRINTER SERVER ................................................................................................ 173APPENDIX F - CONNECTION SETUP .......................................................................................... 179
   8 Chapter 1 Introduction NexusLink 3240 is a Multi-DSL bonding solution with optional VoIP service (FXS port x2) for high-performance Internet access. In addition, NexusLink 3240 supports high power (400mw) dual bands (802.11n 2.4GHz & 802.11ac 5GHz) to create a large Wi-Fi footprint for the most seamless video experience as well as blazing fast data speed.
   9 Chapter 2 Installation 2.1 Hardware Setup  Follow the instructions below to complete the hardware setup.  Non-stackable This device is not stackable – do not place units on top of each other, otherwise damage could occur.  BACK PANEL  The figure below shows the back panel of the device.    Power ON Press the power button to the OFF position (OUT). Connect the power adapter to the power port. Attach the power adapter to a wall outlet or other AC source. Press the power button to the ON position (IN). If the Power LED displays as expected then the device is ready for setup (see section 2.2 LED Indicators).  Caution 1: If the device fails to power up, or it malfunctions, first verify that the power cords are connected securely and then power it on again. If the problem persists, contact technical support. Caution 2: Before servicing or disassembling this equipment, disconnect all power cords and telephone lines from their outlets. Reset Button Restore the default parameters of the device by pressing the Reset button for 10 seconds. After the device has rebooted successfully, the front panel should display as expected (see section 2.2 LED Indicators for details).    NOTE:    If pressed down for more than 60 seconds, the NexusLink 3240 will go into a firmware update state (CFE boot mode).  The firmware can then be updated using an Internet browser pointed to the default IP address.
   10 Phone Ports For VoIP service, connect telephone(s) to these ports with RJ11 cables.  ETH WAN PORT This port has the same features as the LAN ports described below with additional Ethernet WAN functionality.  Ethernet (LAN) Ports Use 1000-BASE-T RJ-45 cables to connect up to four network devices to a Gigabit LAN, or 10/100BASE-T RJ-45 cables for standard network usage. These ports are auto-sensing MDI/X; so either straight-through or crossover cable can be used.  USB Host Port (Type A) This port can be used to connect the router to a printer, or supported USB devices. DSL Port  Connect to an ADSL2/2+ or VDSL with this RJ11 Port.    This device contains a micro filter which removes the analog phone signal.  If you wish, you can connect a regular telephone to the same line by using a POTS splitter.       FRONT PANEL     2.4G WiFi On/Off & WPS Button Press and release the WiFi-WPS button to activate WPS for the 2.4GHz WiFi interface (make sure the WPS is enabled in Wireless->2.4GHz->Security page).Press and hold WiFi-WPS button more than 10 seconds to enable/disable 2.4GHz WiFi.   5G WiFi On/Off & WPS Button Press and release the WiFi-WPS button to activate WPS for the 5GHz WiFi interface (make sure the WPS is enabled in Wireless->5GHz->Security page).Press and hold WiFi-WPS button more than 10 seconds to enable/disable 5GHz WiFi.
   11 2.2 LED Indicators The front panel LED indicators are shown below and explained in the following table. This information can be used to check the status of the device and its connections.      LED  Color  Mode  Function POWER GREEN  On  The device is powered up. Off  The device is powered down. RED On POST (Power On Self Test) failure or other malfunction.  A malfunction is any error of internal sequence or state that will prevent the device from connecting to the DSLAM or passing customer data.  PHONE 1  GREEN  On  An FXS port is off hook. Off  An FXS port is on hook. PHONE 2  GREEN  On  An FXS port is off hook.  Off  An FXS port is on hook. ETH WAN GREEN  On  WAN is connected in 1000 Mbps. Off  Ethernet WAN is not connected. Blink  In TX/RX over 1000 Mbps YELLOW  On  Ethernet is connected in 10/100 Mbps. Off  Ethernet WAN is not connected. Blink  In TX/RX over 10/100 Mbps. ETH 4 to 1 GREEN  On  Ethernet is connected at 1000 Mbps. Off  Ethernet is not connected. Blink  In TX/RX over 1000 Mbps. YELLOW  On  Ethernet is connected at 10/100 Mbps. Off  Ethernet is not connected. Blink  In TX/RX over 10/100 Mbps. WPS  GREEN On WPS(2.4G) WPS enabled and client connected to WLAN. Off WPS(2.4G) WPS disabled. Blink  WPS(2.4G) WPS connection in progress, 120 seconds or until client connected. YELLOW On  WPS(5G WPS enabled and client connected to WLAN. Off  WPS(5G) WPS disabled. Blink  WPS(5G) WPS connection in progress, 120 seconds or until client connected.
   12 WiFi 2.4G  GREEN On  The wireless module is ready. (i.e. installed and enabled). Off  The wireless module is not ready. (i.e. either not installed or disabled). Blink  Data transmitting or receiving over WLAN. WiFi 5G  GREEN On  The wireless module is ready. (i.e. installed and enabled). Off  The wireless module is not ready. (i.e. either not installed or disabled). Blink  Data transmitting or receiving over WLAN. DSL 1  GREEN On  xDSL Link is established. Off  xDSL Link is not established. Blink  The xDSL link is training or some traffic is passing through xDSL. DSL 2  GREEN On  xDSL Link is established. Off  xDSL Link is not established. Blink  The xDSL link is training or some traffic is passing through xDSL. INTERNET GREEN  On  IP connected and no traffic detected.  If an IP or PPPoE session is dropped due to an idle timeout, the light will remain green if an ADSL connection is still present. Off  Modem power off, modem in bridged mode or ADSL connection not present.  In addition, if an IP or PPPoE session is dropped for any reason, other than an idle timeout, the light is turned off. Blink  IP connected and IP Traffic is passing thru the device (either direction) RED On Device attempted to become IP connected and failed (no DHCP response, no PPPoE response, PPPoE authentication failed, no IP address from IPCP, etc.)
   13 Chapter 3 Web User Interface This section describes how to access the device via the web user interface (WUI) using an Internet browser such as Internet Explorer (version 5.0 and later).   3.1 Default Settings The factory default settings of this device are summarized below.  •  LAN IP address: 192.168.1.1 •  LAN subnet mask: 255.255.255.0 •  Administrative access (username: root, password: 12345) •  User access (username: user, password: user) •  Remote (WAN) access (username: support, password: support) •  WLAN access: enabled     Technical Note  During power on, the device initializes all settings to default values.  It will then read the configuration profile from the permanent storage section of flash memory.  The default attributes are overwritten when identical attributes with different values are configured.  The configuration profile in permanent storage can be created via the web user interface or telnet user interface, or other management protocols.  The factory default configuration can be restored either by pushing the reset button for more than ten seconds until the power indicates LED blinking or by clicking the Restore Default Configuration option in the Restore Settings screen.
   14 3.2 IP Configuration DHCP MODE  When the NexusLink 3240 powers up, the onboard DHCP server will switch on. Basically, the DHCP server issues and reserves IP addresses for LAN devices, such as your PC.  To obtain an IP address from the DCHP server, follow the steps provided below.    NOTE:  The following procedure assumes you are running Windows.  However, the general steps involved are similar for most operating systems (OS). Check your OS support documentation for further details. STEP 1:   From the Network Connections window, open Local Area Connection (You may also access this screen by double-clicking the Local Area Connection icon on your taskbar). Click the Properties button. STEP 2:  Select Internet Protocol (TCP/IP) and click the Properties button.  STEP 3:  Select Obtain an IP address automatically as shown below.      STEP 4:  Click OK to submit these settings.  If you experience difficulty with DHCP mode, you can try static IP mode instead.
   15 STATIC IP MODE  In static IP mode, you assign IP settings to your PC manually.  Follow these steps to configure your PC IP address to use subnet 192.168.1.x.  NOTE:  The following procedure assumes you are running Windows.  However, the general steps involved are similar for most operating systems (OS). Check your OS support documentation for further details.  STEP 1:  From the Network Connections window, open Local Area Connection (You may also access this screen by double-clicking the Local Area Connection icon on your taskbar). Click the Properties button. STEP 2:  Select Internet Protocol (TCP/IP) and click the Properties button. STEP 3:  Change the IP address to the 192.168.1.x (1<x<255) subnet with subnet mask of 255.255.255.0. The screen should now display as shown below.      STEP 4:  Click OK to submit these settings.
   16  3.3 Login Procedure Perform the following steps to login to the web user interface.    NOTE:  The default settings can be found in section 3.1 Default Settings.     STEP 1:  Start the Internet browser and enter the default IP address for the device in the Web address field. For example, if the default IP address is 192.168.1.1, type http://192.168.1.1.  NOTE:  For local administration (i.e. LAN access), the PC running the browser must be attached to the Ethernet, and not necessarily to the device.   For remote access (i.e. WAN), use the IP address shown on the Device Information screen and login with remote username and password.  STEP 2:  A dialog box will appear, such as the one below.  Enter the default username and password, as defined in section 3.1 Default Settings.       Click OK to continue.      NOTE:   The login password can be changed later (see section 9.6.1 Accounts).
   17  STEP 3:  After successfully logging in for the first time, you will reach this screen.        You can also reach this page by clicking on the following icon located at the top of the screen.
   18 Chapter 4 Device Information You can reach this page by clicking on the following icon located at the top of the screen.   The web user interface window is divided into two frames, the main menu (on the left) and the display screen (on the right). The main menu has several options and selecting each of these options opens a submenu with more selections.  NOTE:   The menu items shown are based upon the configured connection(s) and user account privileges. For example, user account has limited access to configuration modification.  Device Info is the first selection on the main menu so it will be discussed first.  Subsequent chapters will introduce the other main menu options in sequence.  The Device Info Summary screen displays at startup.    This screen shows hardware, software, IP settings and other related information.
   19 4.1 WAN Select WAN from the Device Info submenu to display the configured PVC(s).    Heading  Description Interface   Name of the interface for WAN Description  Name of the WAN connection Type  Shows the connection type  VlanMuxId  Shows 802.1Q VLAN ID IPv6  Shows WAN IPv6 status Igmp Pxy  Shows Internet Group Management Protocol (IGMP) proxy status Igmp Src Enbl  Shows the status of WAN interface used as IGMP source MLD Pxy  Shows Multicast Listener Discovery (MLD) proxy status MLD Src Enbl  Shows the status of WAN interface used as MLD source  NAT  Shows Network Address Translation (NAT) status Firewall  Shows the status of Firewall Status  Lists the status of DSL link IPv4 Address  Shows WAN IPv4 address IPv6 Address  Shows WAN IPv6 address
   20 4.2 Statistics This selection provides LAN, WAN, ATM and xDSL statistics.  NOTE:  These screens are updated automatically every 15 seconds.  Click Reset Statistics to perform a manual update. 4.2.1 LAN Statistics This screen shows data traffic statistics for each LAN interface.    Heading  Description Interface  LAN interface(s) Received/Transmitted: - Bytes  - Pkts  - Errs  - Drops Number of Bytes  Number of Packets  Number of packets with errors Number of dropped packets
   21 4.2.2 WAN Service This screen shows data traffic statistics for each WAN interface.    Heading  Description Interface  WAN interfaces Description  WAN service label Received/Transmitted   -  Bytes                         -  Pkts                         -  Errs                         -  Drops Number of Bytes  Number of Packets  Number of packets with errors Number of dropped packets
   22 4.2.3 XTM Statistics The following figure shows ATM (Asynchronous Transfer Mode)/PTM (Packet Transfer Mode) statistics.   XTM Interface Statistics  Heading  Description Port Number  ATM PORT (0-1) In Octets  Number of octets received over the interface Out Octets  Number of octets transmitted over the interface In Packets  Number of packets received over the interface Out Packets  Number of packets transmitted over the interface In OAM Cells  Number of OAM Cells received over the interface Out OAM Cells  Number of OAM Cells transmitted over the interface In ASM Cells  Number of ASM Cells received over the interface Out ASM Cells  Number of ASM Cells transmitted over the interface In Packet Errors  Number of packets in Error In Cell Errors  Number of cells in Error
   23 4.2.4 xDSL Statistics The xDSL Statistics screen displays information corresponding to the xDSL type. The two examples below (VDSL & ADSL) show this variation.   VDSL
   24  ADSL    Click the Reset Statistics button to refresh this screen.  Field  Description Mode  VDSL, VDSL2 Traffic Type  ATM, PTM Status  Lists the status of the DSL link Link Power State  Link output power state phyR Status  Shows the status of PhyR™ (Physical Layer Re-Transmission) impulse noise protection Line Coding (Trellis)  Trellis On/Off
   25 Field  Description SNR Margin (0.1 dB)  Signal to Noise Ratio (SNR) margin Attenuation (0.1 dB)  Estimate of average loop attenuation in the downstream direction Output Power  (0.1 dBm)  Total upstream output power Attainable Rate (Kbps)  The sync rate you would obtain Rate (Kbps)  Current sync rates downstream/upstream   In VDSL mode, the following section is inserted.  MSGc  Number of bytes in overhead channel message B  Number of bytes in Mux Data Frame M  Number of Mux Data Frames in a RS codeword T   Number of Mux Data Frames in an OH sub-frame R   Number of redundancy bytes in the RS codeword S   Number of data symbols the RS codeword spans L   Number of bits transmitted in each data symbol D   The interleaver depth I  The interleaver block size in bytes N  RS codeword size Delay   The delay in milliseconds (msec) INP DMT symbol  Super Frames  Total number of super frames Super Frame Errors  Number of super frames received with errors RS Words  Total number of Reed-Solomon code errors RS Correctable Errors  Total Number of RS with correctable errors RS Uncorrectable Errors  Total Number of RS words with uncorrectable errors  OH Frames  Total number of OH frames OH Frame Errors  Number of OH frames received with errors RS Words  Total number of Reed-Solomon code errors RS Correctable Errors  Total Number of RS with correctable errors RS Uncorrectable Errors  Total Number of RS words with uncorrectable errors  HEC Errors  Total Number of Header Error Checksum errors OCD Errors  Total Number of Out-of-Cell Delineation errors LCD Errors  Total number of Loss of Cell Delineation Total Cells  Total number of ATM cells (including idle + data cells) Data Cells  Total number of ATM data cells Bit Errors  Total number of bit errors
   26 Total ES  Total Number of Errored Seconds Total SES  Total Number of Severely Errored Seconds  Total UAS  Total Number of Unavailable Seconds    xDSL BER TEST Click xDSL BER Test on the xDSL Statistics screen to test the Bit Error Rate (BER). A small pop-up window will open after the button is pressed, as shown below.  Click Start to start the test or click Close to cancel the test. After the BER testing is complete, the pop-up window will display as follows.
   27 xDSL TONE GRAPH  Click Draw Graph on the xDSL Statistics screen and a pop-up window will display the xDSL statistics graph, including SNR, Bits per tone, QLN and Hlog of the xDSL line connection, as shown below.
   28 4.3 Route Choose Route to display the routes that the NexusLink 3240 has found.     Field  Description Destination  Destination network or destination host Gateway  Next hop IP address Subnet Mask  Subnet Mask of Destination Flag  U: route is up  !: reject route G: use gateway H: target is a host R: reinstate route for dynamic routing D: dynamically installed by daemon or redirect M: modified from routing daemon or redirect Metric  The 'distance' to the target (usually counted in hops).  It is not used by recent kernels, but may be needed by routing daemons. Service  Shows the WAN connection label Interface  Shows connection interfaces
   29 4.4 ARP Click ARP to display the ARP information.    Field  Description IP address  Shows IP address of host PC Flags  Complete, Incomplete, Permanent, or Publish HW Address  Shows the MAC address of host PC Device  Shows the connection interface    4.5 DHCP Click DHCP to display all DHCP Leases.    Field  Description Hostname  Shows the device/host/PC network name MAC Address  Shows the Ethernet MAC address of the device/host/PC IP Address  Shows IP address of device/host/PC Expires In  Shows how much time is left for each DHCP Lease
   30      Field  Description IPv6 Address  Shows IP address of device/host/PC MAC Address  Shows the Ethernet MAC address of the device/host/PC Duration  Shows leased time in hours Expires In  Shows how much time is left for each DHCP Lease
   31 4.6 NAT Session This page displays all NAT connection session including both UPD/TCP protocols passing through the device.    Click the “Show All” button to display the following.     Field  Description Source IP     The source IP from which the NAT session is established  Source Port     The source port from which the NAT session is established  Destination IP    The IP which the NAT session was connected to Destination Port   The port which the NAT session was connected to Protocol    The Protocol used in establishing the particular NAT session Timeout  The time remaining for the TCP/UDP connection to be active
   32 4.7 IGMP Info Click IGMP Info to display the list of IGMP entries broadcasting through IGMP proxy enabled wan connection.     Field  Description Interface  The Source interface from which the IGMP report was received WAN  The WAN interface from which the multicast traffic is received Groups  The destination IGMP group address Member  The Source IP from which the IGMP report was received Timeout  The time remaining before the IGMP report expires
   33 4.8 IPv6 4.8.1 IPv6 Info Click IPv6 Info to display the IPv6 WAN connection info.       Field  Description Interface  WAN interface with IPv6 enabled Status  Connection status of the WAN interface Address  IPv6 Address of the WAN interface Prefix  Prefix received/configured on the WAN interface Device Link-local Address  The CPE's LAN Address Default IPv6 Gateway  The default WAN IPv6 gateway IPv6 DNS Server The IPv6 DNS servers received from the WAN interface / configured manually
   34 4.8.2 IPv6 Neighbor Click IPv6 Neighbor to display the list of IPv6 nodes discovered.   Field  Description IPv6 Address  Ipv6 address of the device(s) found Flags  Status of the neighbor device HW Address  MAC address of the neighbor device Device  Interface from which the device is located
   35 4.8.3 IPv6 Route Click IPv6 Route to display the IPv6 route info.        Field  Description Destination  Destination IP Address Gateway  Gateway address used for destination IP Metric  Metric specified for gateway Interface  Interface used for destination IP
   36 4.9 CPU & Memory  Displays the system performance graphs. Shows the current loading of the CPU and memory usage with dynamic updates.    Note: This graph is unavailable for Internet Explorer users.
   37 4.10 Network Map The network map is a graphical representation of router’s wan status and LAN devices.   Note: This graph is unavailable for Internet Explorer users.   4.11 Wireless 4.11.1 Station Info This page shows authenticated wireless stations and their status. Click the Refresh button to update the list of stations in the WLAN.    Consult the table below for descriptions of each column heading.
   38   Field  Description MAC  Lists the MAC address of all the stations. Associated  Lists all the stations that are associated with the Access Point, along with the amount of time since packets were transferred to and from each station. If a station is idle for too long, it is removed from this list. Authorized  Lists those devices with authorized access. SSID  Lists which SSID of the modem that the stations connect to. Interface  Lists which interface of the modem that the stations connect to.
   39 4.11.2 Site Survey The graph displays wireless APs found in your neighborhood by channel.
   40 Chapter 5 Basic Setup You can reach this page by clicking on the following icon located at the top of the screen.      This will bring you to the following screen.
   41 5.1 Wan Setup Add or remove ATM, PTM and ETH WAN interface connections here.     Click Add to create a new Layer 2 Interface (see Appendix F - Connection Setup). NOTE:  Up to 8 ATM interfaces can be created and saved in flash memory.  To remove a connection, click the Remove button.
   42 5.1.1 WAN Service Setup This screen allows for the configuration of WAN interfaces.    Click the Add button to create a new connection. For connections on ATM or PTM or ETH WAN interfaces see Appendix F - Connection Setup.   To remove a connection, select its Remove column radio button and click Remove.    Heading  Description Interface   Name of the interface for WAN Description  Name of the WAN connection Type  Shows the connection type  Vlan8021p  VLAN ID is used for VLAN Tagging (IEEE 802.1Q) VlanMuxId  Shows 802.1Q VLAN ID VlanTpid  VLAN Tag Protocol Identifier IGMP Proxy  Shows Internet Group Management Protocol (IGMP) Proxy status IGMP Source  Shows the status of WAN interface used as IGMP source NAT  Shows Network Address Translation (NAT) status Firewall  Shows the Security status IPv6  Shows the WAN IPv6 address MLD Proxy  Shows Multicast Listener Discovery (MLD) Proxy status Mld Source  Shows the status of WAN interface used as MLD source Remove  Select interfaces to remove Edit  Click the Edit button to make changes to the WAN interface.  To remove a connection, select its Remove column radio button and click Remove.  NOTE:  Up to 16 PVC profiles can be configured and saved in flash memory.
   43 5.2 NAT For NAT features under this section to work, NAT must be enabled in at least one PVC.  5.2.1 Virtual Servers Virtual Servers allow you to direct incoming traffic from the WAN side (identified by Protocol and External port) to the internal server with private IP addresses on the LAN side. The Internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side.  A maximum of 32 entries can be configured.    To add a Virtual Server, click Add. The following will be displayed.    Click Apply/Save to apply and save the settings.     Consult the table below for field and header descriptions.
   44 Field/Header  Description Choose All InterfaceVirtual server rules will be created for all WAN interfaces. Choose One Interface  Use Interface  Select a WAN interface from the drop-down menu. Select a Service Or  Custom Service User should select the service from the list. Or User can enter the name of their choice. Server IP Address  Enter the IP address for the server. Enable NAT Loopback  Allows local machines to access virtual server via WAN IP Address External Port Start  Enter the starting external port number (when you select Custom Server). When a service is selected, the port ranges are automatically configured. External Port End  Enter the ending external port number (when you select Custom Server). When a service is selected, the port ranges are automatically configured. Protocol  TCP, TCP/UDP, or UDP. Internal Port Start  Enter the internal port starting number (when you select Custom Server). When a service is selected the port ranges are automatically configured Internal Port End  Enter the internal port ending number (when you select Custom Server). When a service is selected, the port ranges are automatically configured.
   45 5.2.2 Port Triggering Some applications require that specific ports in the firewall be opened for access by the remote parties.  Port Triggers dynamically 'Open Ports' in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the 'Triggering Ports'.  The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the 'Open Ports'.  A maximum 32 entries can be configured.    To add a Trigger Port, click Add. The following will be displayed.    Click Save/Apply to save and apply the settings.   Consult the table below for field and header descriptions.    Field/Header  Description Use Interface  Select a WAN interface from the drop-down menu.
   46 Field/Header  Description Select an Application Or  Custom Application User should select the application from the list. Or  User can enter the name of their choice. Trigger Port Start  Enter the starting trigger port number (when you select custom application).   When an application is selected, the port ranges are automatically configured. Trigger Port End  Enter the ending trigger port number (when you select custom application).   When an application is selected, the port ranges are automatically configured. Trigger Protocol  TCP, TCP/UDP, or UDP. Open Port Start  Enter the starting open port number (when you select custom application).   When an application is selected, the port ranges are automatically configured. Open Port End  Enter the ending open port number (when you select custom application).   When an application is selected, the port ranges are automatically configured. Open Protocol  TCP, TCP/UDP, or UDP.
   47 5.2.3 DMZ Host The DSL router will forward IP packets from the WAN that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer.    To Activate the DMZ host, enter the DMZ host IP address and click Save/Apply.  To Deactivate the DMZ host, clear the IP address field and click Save/Apply.  Enable NAT Loopback allows PC on the LAN side to access servers in the LAN network via the router’s WAN IP.
   48 5.2.4 IP Address Map  Mapping Local IP (LAN IP) to some specified Public IP (WAN IP).    Field/Header  Description Rule  The number of the rule Type  Mapping type from local to public Local Start IP  The beginning of the local IP Local End IP  The ending of the local IP Public Start IP  The beginning of the public IP Public End IP  The ending of the public IP Remove  Remove this rule  Click the Add button to display the following.   Select a Service, then click the Save/Apply button.  One to One: mapping one local IP to a specific public IP  Many to one: mapping a range of local IP to a specific public IP  Many to many(Overload): mapping a range of local IP to a different range of public IP  Many to many(No Overload): mapping a range of local IP to a same range of public IP
   49 5.2.5  ALG/Pass-Through Support ALG Pass-through for the listed protocols.    To allow/deny the corresponding ALG protocol, select Enable / Disable and then click the Save button.  After reboot, the protocol will be added/removed from the system module.
   50 5.3 LAN Configure the LAN interface settings and then click Apply/Save.    Consult the field descriptions below for more details.  GroupName: Select an Interface Group. 1st LAN INTERFACE IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port.
   51 Enable IGMP Snooping:    Standard Mode:  In standard mode, multicast traffic will flood to all            bridge ports when no client subscribes to a multicast group           even if IGMP snooping is enabled.  Blocking Mode:    In blocking mode, the multicast data traffic will be blocked and not            flood to all bridge ports when there are no client subscriptions to any multicast group. Enable IGMP LAN to LAN Multicast: Select Enable from the drop-down menu to allow IGMP LAN to LAN Multicast forwarding Enable Enhanced IGMP: Enable by ticking the checkbox . IGMP packets between LAN ports will be blocked. Enable LAN side firewall: Enable by ticking the checkbox .  DHCP Server:  To enable DHCP, select Enable DHCP server and enter Start and End IP addresses and the Leased Time. This setting configures the router to automatically assign IP, default gateway and DNS server addresses to every PC on your LAN.   Setting TFTP Server: Enable by ticking the checkbox . Then, input the TFTP                            server address or an IP address.   Static IP Lease List:  A maximum of 32 entries can be configured.   To add an entry, enter MAC address and Static IP address and then click      Apply/Save.  To remove an entry, tick the corresponding checkbox  in the Remove column and then click the Remove Entries button, as shown below.
   52   Select Enable DHCP Server Relay (not available if NAT enabled), and enter the DHCP Server IP Address.  This allows the Router to relay the DHCP packets to the remote DHCP server.  The remote DHCP server will provide the IP address.    2ND LAN INTERFACE  To configure a secondary IP address, tick the checkbox  outlined (in RED) below.    IP Address: Enter the secondary IP address for the LAN port. Subnet Mask: Enter the secondary subnet mask for the LAN port.   Ethernet Media Type:  Configure auto negotiation, or enforce selected speed and duplex mode for the Ethernet ports.
   53 5.3.1 LAN IPv6 Autoconfig Configure the LAN interface settings and then click Save/Apply.     Consult the field descriptions below for more details.
   54 LAN IPv6 Link-Local Address Configuration  Heading  Description EUI-64  Use EUI-64 algorithm to calculate link-local address from MAC address User Setting  Use the Interface Identifier field to define a link-local address  Static LAN IPv6 Address Configuration  Heading  Description Interface Address  (prefix length is required): Configure static LAN IPv6 address and subnet prefix length  IPv6 LAN Applications  Heading  Description Stateless  Use stateless configuration Refresh Time (sec):  The information refresh time option specifies how long a client should wait before refreshing information retrieved from DHCPv6 Stateful  Use stateful configuration  Start interface ID:  Start of interface ID to be assigned to dhcpv6 client  End interface ID:  End of interface ID to be assigned to dhcpv6 client  Leased Time (hour):  Lease time for dhcpv6 client to use the assigned IP address  Static IP Lease List:  A maximum of 32 entries can be configured.   To add an entry, enter MAC address and Interface ID and then click Apply/Save.   To remove an entry, tick the corresponding checkbox  in the Remove column and
   55 then click the Remove Entries button, as shown below.    Heading  Description Enable RADVD  Enable use of router advertisement daemon RA interval Min(sec):  Minimum time to send router advertisement RA interval Max(sec): Maximum time to send router advertisement Reachable Time(ms):  The time, in milliseconds that a neighbor is reachable after receiving reachability confirmation Default Preference:  Preference level associated with the default router MTU (bytes):  MTU value used in router advertisement messages to insure that all nodes on a link use the same MTU value Enable Prefix Length Relay   Use prefix length receive from WAN interface Enable Configuration Mode  Manually configure prefix, prefix length, preferred lifetime and valid lifetime used in router advertisement Enable ULA Prefix Advertisement Allow RADVD to advertise Unique Local Address Prefix Randomly Generate  Use a Randomly Generated Prefix Statically Configure  Prefix  Specify the prefix to be used  Preferred Life Time (hour)  The preferred life time for this prefix  Valid Life Time (hour)  The valid life time for this prefix Enable MLD Snooping  Enable/disable IPv6 multicast forward to LAN ports Standard Mode Blocking Mode  In standard mode, IPv6 multicast traffic will flood to all bridge ports when no client subscribes to a multicast group even if MLD snooping is enabled  In blocking mode, IPv6 multicast data traffic will be blocked and not flood to all bridge ports when there are no client subscriptions to any multicast group Enable MLD LAN To LAN Multicast  Enable/disable IPv6 multicast between LAN ports
   56 5.3.2 Static IP Neighbor This page is used to configure a static IPv4 or IPv6 Neighbor entry.  Static ARP entries will be created for these neighbor devices.     Click the Add button to display the following.    Click Apply/Save to apply and save the settings.  Heading  Description IP Version  The IP version used for the neighbor device IP Address  Define the IP Address for the neighbor device MAC Address  The MAC Address of the neighbor device Associated Interface  The interface where the neighbor device is located
   57 5.3.3 UPnP Select the checkbox  provided and click Apply/Save to enable UPnP protocol.
   58 5.4 Wireless  5.4.1 Basic 2.4GHz The Basic option allows you to configure basic features of the wireless LAN interface. Among other things, you can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements.    Click the Apply/Save button to apply the selected wireless options.  Consult the table below for descriptions of these options.  Option  Description Enable Wireless  A checkbox  that enables or disables the wireless LAN interface.  When selected, a set of basic wireless options will appear. Enable Wireless Hotspot2.0 Enable Wireless Hotspot 2.0 (Wi-Fi Certified Passpoint) on the wireless interface.
   59 Option  Description Hide Access Point  Select Hide Access Point to protect the access point from detection by wireless active scans. To check AP status in Windows XP, open Network Connections from the start Menu and select View Available Network Connections. If the access point is hidden, it will not be listed there. To connect a client to a hidden access point, the station must add the access point manually to its wireless configuration.   Clients Isolation  When enabled, it prevents client PCs from seeing one another in My Network Places or Network Neighborhood. Also, prevents one wireless client communicating with another wireless client. Disable WMM Advertise        Stops the router from ‘advertising’ its Wireless Multimedia (WMM) functionality, which provides basic quality of service for time-sensitive applications (e.g. VoIP, Video). Enable Wireless Multicast Forwarding Select the checkbox  to enable this function. SSID  [1-32 characters] Sets the wireless network name. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the WLAN. If the SSID does not match, that user will not be granted access.   BSSID  The BSSID is a 48-bit identity used to identify a particular BSS (Basic Service Set) within an area.  In Infrastructure BSS networks, the BSSID is the MAC (Media Access Control) address of the AP (Access Point); and in Independent BSS or ad hoc networks, the BSSID is generated randomly. Country  A drop-down menu that permits worldwide and specific national settings.  Local regulations limit channel range:  US= worldwide, Japan=1-14, Jordan= 10-13, Israel= 1-13 Country RegRev  Wireless country code for transmit power limit. Max Clients  The maximum number of clients that can access the router. Wireless - Guest / Virtual Access Points This router supports multiple SSIDs called Guest SSIDs or Virtual Access Points. To enable one or more Guest SSIDs select the checkboxes  in the Enabled column. To hide a Guest SSID, select its checkbox  in the Hidden column.    Do the same for Isolate Clients and Disable WMM Advertise.  For a description of these two functions, see the previous entries for “Clients Isolation” and “Disable WMM Advertise”. Similarly, for Enable WMF, Max Clients and BSSID, consult the matching entries in this table.  NOTE: Remote wireless hosts cannot scan Guest SSIDs.
   60 5.4.2 Security 2.4GHz The following screen appears when Wireless Security is selected. The options shown here allow you to configure security features of the wireless LAN interface.      Please see 6.13.3 for WPS setup instructions.  Click Apply/Save to implement new configuration settings. WIRELESS SECURITY  Setup requires that the user configure these settings using the Web User Interface (see the table below).   Select SSID Select the wireless network name from the drop-down menu. SSID stands for Service Set Identifier.  All stations must be configured with the correct SSID to access the WLAN. If the SSID does not match, that client will not be granted access.  Network Authentication This option specifies whether a network key is used for authentication to the wireless network.  If network authentication is set to Open, then no authentication is provided.  Despite this, the identity of the client is still verified.    Each authentication type has its own settings.  For example, selecting 802.1X authentication will reveal the RADIUS Server IP address, Port and Key fields.  WEP Encryption will also be enabled as shown below.
   61    The settings for WPA2-PSK authentication are shown next.    WEP Encryption This option specifies whether data sent over the network is encrypted. The same network key is used for data encryption and network authentication. Four network keys can be defined although only one can be used at any one time. Use the Current Network Key list box to select the appropriate network key.   Security options include authentication and encryption services based on the wired equivalent privacy (WEP) algorithm.  WEP is a set of security services used to protect 802.11 networks from unauthorized access, such as eavesdropping; in this case, the capture of wireless network traffic.   When data encryption is enabled, secret shared encryption keys are generated and used by the source station and the destination station to alter frame bits, thus avoiding disclosure to eavesdroppers.  Under shared key authentication, each wireless station is assumed to have received a secret shared key over a secure channel that is independent from the 802.11 wireless network communications channel.
   62 Encryption Strength This drop-down list box will display when WEP Encryption is enabled.  The key strength is proportional to the number of binary bits comprising the key.  This means that keys with a greater number of bits have a greater degree of security and are considerably more difficult to crack.  Encryption strength can be set to either 64-bit or 128-bit.  A 64-bit key is equivalent to 5 ASCII characters or 10 hexadecimal numbers.  A 128-bit key contains 13 ASCII characters or 26 hexadecimal numbers.  Each key contains a 24-bit header (an initiation vector) which enables parallel decoding of multiple streams of encrypted data.  Please see 6.13 for MAC Filter, Wireless Bridge and Advanced Wireless features. 5.4.3 Basic 5GHz The Basic option allows you to configure basic features of the wireless LAN interface. Among other things, you can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and configure the channel setting for the wireless LAN interface.    Click the Apply/Save button to apply the selected wireless options.  Consult the table below for descriptions of these options.  Option  Description Enable Wireless  A checkbox  that enables or disables the wireless LAN interface.  When selected, a set of basic wireless options will appear. Hide Access Point  Select Hide Access Point to protect the access point from detection by wireless active scans. To check AP status in Windows XP, open Network Connections from the start Menu and select View Available Network Connections. If the access point is hidden, it will not be listed there. To connect a client to a hidden access point, the station must add the access point manually to its wireless configuration.
   63 Option  Description SSID  [1-32 characters] Sets the wireless network name. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the WLAN. If the SSID does not match, that user will not be granted access.   BSSID  The BSSID is a 48-bit identity used to identify a particular BSS (Basic Service Set) within an area.  In Infrastructure BSS networks, the BSSID is the MAC (Media Access Control) address of the AP (Access Point); and in Independent BSS or ad hoc networks, the BSSID is generated randomly. Channel  Drop-down menu that allows selection of a specific channel.  Encryption  The encryption mode used for the wireless LAN interface.   Passphrase  Entering a passphrase of at least 8 digits is required for WPA2 mode and mixed mode wireless encryption. Enable Guest SSID  Click Enable Guest SSID to enable an additional SSID to provide varied access. 5.4.4 Security 5GHz The following screen appears when Wireless Security is selected. The options shown here allow you to configure security features of the wireless LAN interface.      Please see 6.13.3 for WPS setup instructions.  Click Apply/Save to implement new configuration settings.     Please see 6.13 for MAC Filter, Wireless Bridge and Advanced Wireless features.
   64 5.5 Parental Control   This selection provides WAN access control functionality.  5.5.1 Time Restriction This feature restricts access from a LAN device to an outside network through the device on selected days at certain times. Make sure to activate the Internet Time server synchronization as described in section 9.5 Internet Time, so that the scheduled times match your local time. Clicking on the checkbox in the Enable field allows the user to select all / none entries for Enabling/Disabling.   Click Add to display the following screen.   See below for field descriptions. Click Apply/Save to add a time restriction.  User Name: A user-defined label for this restriction. Browser's MAC Address: MAC address of the PC running the browser. Other MAC Address: MAC address of another LAN device.  Days of the Week: The days the restrictions apply. Start Blocking Time: The time the restrictions start. End Blocking Time: The time the restrictions end.
   65 5.5.2 URL Filter This screen allows for the creation of a filter rule for access rights to websites based on their URL address and port number.   Select URL List Type: Exclude or Include.   Tick the Exclude radio button to deny access to the websites listed.  Tick the Include radio button to restrict access to only those listed websites.  Then click Add to display the following screen.    Enter the URL address and port number then click Apply/Save to add the entry to the URL filter.  URL Addresses begin with “www”, as shown in this example.
   66   A maximum of 100 entries can be added to the URL Filter list.
   67 5.6 Home networking  5.6.1 Print Server  This page allows you to enable or disable printer support.    Please reference Appendix E to see the procedure for enabling the Printer Server.   5.6.2 DLNA Enabling DLNA allows users to share digital media, like pictures, music and video, to other LAN devices from the digital media server.  Insert the USB drive into the USB host port on the back of the router.   Click Enable on-board digital media server, a dropdown list of directories found on the USB driver will be available for selection.  Select media path from the drop-down list or manually modify the media library path and click Apply/Save to enable the DLNA media server.
   68 5.6.3 Storage Service Enabling Samba service allows the user to share files on the storage device.   Different levels of user access can be configured after samba security mode is enabled.  This page also displays storage devices attached to the USB host.     Display after storage device attached (for your reference).
   69 5.6.4 USB Speed  This page allows you to enable / disable USB 3.0 device support. Note: Enabling USB 3.0 can cause interference with the built-in 2.4GHz wireless radio. It is advised leaving the default value as USB 2.0
   70 Chapter 6 Advanced Setup  You can reach this page by clicking on the following icon located at the top of the screen.  6.1 Auto-detection setup The auto-detection function is used for CPE to detect WAN service for either ETHWAN or xDSL interfaces. The feature is designed for the scenario that requires only one WAN service in different applications.   The Auto Detection page simply provides a checkbox allowing users to enable or disable the feature. Check the checkbox to display the following configuration options.
   71        Enter the PPP username/password given by your service provider for PPP service detection.   Select a LAN-as-WAN Ethernet port for auto-detect: Select the Ethernet Port that will be used as ETH WAN during auto-detection. For models with ETH WAN port, only ETH WAN port is available to be used as WAN port.
   72   WAN services list for ATM mode: A maximum of 7 WAN services with corresponding PVC are required to be configured for ADSL ATM mode. The services will be detected in order. Users can modify the 7 pre-configured services and select disable to ignore any of those services to meet their own requirement and also reduce the detection cycle.    WAN services list for PTM mode: A maximum of 7 WAN services with corresponding VLAN ID (-1 indicates no VLAN ID is required for the service) are required to be configured for ADSL/VDSL PTM mode and ETHWAN. The services will be detected in order. Users can modify the 7 pre-configured services and select disable to ignore any of the services to meet their own requirements and also reduce the detection cycle.
   73    Click "Apply/Save" to activate the auto-detect function.     Options for each WAN service: These options are selectable for each WAN service. Users can pre-configure both WAN services and other provided settings to meet their deployed requirements.            Auto Detection status and Restart  The Auto-detection status is used to display the real time status of the Auto-detection feature.     The Restart button is used to detect all the WAN services that are either detected by the auto-detection feature or configured manually by users.    The following window will pop up upon clicking the Restart button. Click the OK button to proceed.
   74 Auto Detection notice  Note: The following description concerning ETHWAN is for multiple LAN port devices only.  1) This feature will automatically detect one WAN service only. If customers require multiple WAN services, manual configuration is required. 2) If a physical ETHWAN port is detected, the Auto Detection for ETHWAN will be fixed on the physical ETHWAN port and cannot be configured for any LAN port; if the physical ETHWAN port is not detected, the Auto Detection for ETHWAN will be configured to the 4th LAN port by default and allows it to be configured for any LAN port as well. 3) For cases in which both the DSL port and ETHWAN port are plugged in at the same time, the DSL WAN will have priority over ETHWAN. For example, the ETHWAN port is plugged in with a WAN service detected automatically and then the DSL port is plugged in and linked up. The Auto Detection feature will clear the WAN service for ETHWAN and re-detect the WAN service for DSL port. 4) If none of the pre-configured services are detected, a Bridge service will be created.
   75 6.2 Security For detailed descriptions, with examples, please consult Appendix A - Firewall.  6.2.1 IP Filtering This screen sets filter rules that limit IP traffic (Outgoing/Incoming). Multiple filter rules can be set and each applies at least one limiting condition. For individual IP packets to pass the filter all conditions must be fulfilled.  NOTE:  This function is not available when in bridge mode. Instead, MAC Filtering performs a similar function. OUTGOING IP FILTER  By default, all outgoing IP traffic is allowed, but IP traffic can be blocked with filters.   To add a filter (to block some outgoing IP traffic), click the Add button. On the following screen, enter your filter criteria and then click Apply/Save.   Consult the table below for field descriptions.
   76  Field  Description Filter Name  The filter rule label. IP Version  Select from the drop down menu. Protocol  TCP, TCP/UDP, UDP, or ICMP. Source IP address  Enter source IP address. Source Port (port or port:port)  Enter source port number or range. Destination IP address  Enter destination IP address. Destination Port (port or port:port) Enter destination port number or range.  INCOMING IP FILTER By default, all incoming IP traffic is blocked, but IP traffic can be allowed with filters.  To add a filter (to allow incoming IP traffic), click the Add button.  On the following screen, enter your filter criteria and then click Apply/Save.  Consult the table below for field descriptions.
   77 Field  Description Filter Name  The filter rule label. IP Version  Select from the drop down menu. Protocol  TCP, TCP/UDP, UDP, or ICMP. Policy  Permit/Drop packets specified by the firewall rule. Source IP address  Enter source IP address. Source Port (port or port:port)  Enter source port number or range. Destination IP address  Enter destination IP address. Destination Port (port or port:port) Enter destination port number or range.  At the bottom of this screen, select the WAN and LAN Interfaces to which the filter rule will apply. You may select all or just a subset. WAN interfaces in bridge mode or without firewall enabled are not available.
   78 Denial of Service  Denial of Services currently provides Syn-flood protection, furtive port scanner protection and Ping of death protection. This web page allows you to activate/de-activate them and to set the maximum average limit (packet per second) and the maximum burst (packet amount) for each protection.      Click the Apply/Save button to save and (de)activate the protection.
   79 6.2.2 MAC Filtering NOTE:  This option is only available in bridge mode. Other modes use IP Filtering to perform a similar function. Each network device has a unique 48-bit MAC address. This can be used to filter (block or forward) packets based on the originating device. MAC filtering policy and rules for the NexusLink 3240 can be set according to the following procedure.   The MAC Filtering Global Policy is defined as follows. FORWARDED means that all MAC layer frames will be FORWARDED except those matching the MAC filter rules.  BLOCKED means that all MAC layer frames will be BLOCKED except those matching the MAC filter rules. The default MAC Filtering Global policy is FORWARDED. It can be changed by clicking the Change Policy button.    Choose Add or Remove to configure MAC filtering rules. The following screen will appear when you click Add. Create a filter to identify the MAC layer frames by specifying at least one condition below. If multiple conditions are specified, all of them must be met.   Click Save/Apply to save and activate the filter rule.
   80 Consult the table below for detailed field descriptions.   Field  Description Protocol Type  PPPoE, IPv4, IPv6, AppleTalk, IPX, NetBEUI, IGMP Destination MAC Address  Defines the destination MAC address Source MAC Address  Defines the source MAC address Frame Direction  Select the incoming/outgoing packet interface WAN Interfaces  Applies the filter to the selected bridge interface
   81 6.3 Quality of Service (QoS) NOTE:  QoS must be enabled in at least one PVC to display this option.  (See Appendix F - Connection Setup for detailed PVC setup instructions).   To Enable QoS tick the checkbox and select a Default DSCP Mark.    Click Apply/Save to activate QoS.     QoS and DSCP Mark are defined as follows:  Quality of Service (QoS): This provides different priority to different users or data flows, or guarantees a certain level of performance to a data flow in accordance with requests from Queue Prioritization.  Default Differentiated Services Code Point (DSCP) Mark: This specifies the per hop behavior for a given flow of packets in the Internet Protocol (IP) header that do not match any other QoS rule.
   82 6.3.1 QoS Queue   6.3.1.1  QoS Queue Configuration Configure queues with different priorities to be used for QoS setup.  In ATM mode, a maximum of 16 queues can be configured. In PTM mode, a maximum of 8 queues can be configured. For each Ethernet interface, a maximum of 8 queues can be configured. For each Ethernet interface, a maximum of 8 queues can be configured.  (Please see the screen on the following page).
   83
   84 To remove queues, check their remove-checkboxes (for user created queues), then click the Remove button.  The Enable button will scan through every queue in the table. Queues with the enable-checkbox checked will be enabled. Queues with the enable-checkbox un-checked will be disabled.  The enable-checkbox also shows status of the queue after page reload.  Note that if WMM function is disabled in the Wireless Page, queues related to wireless will not take effect. This function follows the Differentiated Services rule of IP QoS. You can create a new Queue entry by clicking the Add button.   Enable and assign an interface and precedence on the next screen. Click Save/Reboot on this screen to activate it. Click Add to display the following screen.  Name: Identifier for this Queue entry. Enable: Enable/Disable the Queue entry. Interface: Assign the entry to a specific network interface (QoS enabled).    After selecting an Interface the following will be displayed.
   85    The precedence list shows the scheduler algorithm for each precedence level. Queues of equal precedence will be scheduled based on the algorithm. Queues of unequal precedence will be scheduled based on SP.   Shaping Rate: Specify a shaping rate limit to the defined queue.  Click Apply/Save to apply and save the settings.
   86 6.3.1.2 Wlan Queue   Displays the list of available wireless queues for WMM and wireless data transmit priority.
   87 6.3.2  QoS Classification The network traffic classes are listed in the following table.    Click Add to configure a network traffic class rule and Enable to activate it. To delete an entry from the list, click Remove.  This screen creates a traffic class rule to classify the upstream traffic, assign queuing priority and optionally overwrite the IP header DSCP byte. A rule consists of a class name and at least one logical condition. All the conditions specified in the rule must be satisfied for it to take effect.    Click Apply/Save to save and activate the rule.
   88   Field  Description Traffic Class Name  Enter a name for the traffic class. Rule Order  Last is the only option. Rule Status  Disable or enable the rule. Classification Criteria Ingress Interface Select an interface: (i.e. LAN, WAN, local, ETH1, ETH2, ETH3, wl0) Ether Type  Set the Ethernet type (e.g. IP, ARP, IPv6). Source MAC Address  A packet belongs to SET-1, if a binary-AND of its source MAC address with the Source MAC Mask is equal to the binary-AND of the Source MAC Mask and this field. Source MAC Mask  This is the mask used to decide how many bits are checked in Source MAC Address. Destination MAC Address  A packet belongs to SET-1 then the result that the Destination MAC Address of its header binary-AND to the Destination MAC Mask must equal to the result that this field binary-AND to the Destination MAC Mask. Destination MAC Mask  This is the mask used to decide how many bits are checked in the Destination MAC Address. Classification Results Specify Egress Interface  Choose the egress interface from the available list.  Specify Egress Queue  Choose the egress queue from the list of available for the specified egress interface. Mark Differentiated Service Code Point   The selected Code Point gives the corresponding priority to packets that satisfy the rule. Mark 802.1p Priority  Select between 0-7.  - Class non-vlan packets egress to a non-vlan interface will be tagged with VID 0 and the class rule p-bits. - Class vlan packets egress to a non-vlan interface will have the packet p-bits re-marked by the class rule p-bits. No additional vlan tag is added. - Class non-vlan packets egress to a vlan interface will be tagged with the interface VID and the class rule p-bits. - Class vlan packets egress to a vlan interface will be additionally tagged with the packet VID, and the class rule p-bits. Set Rate Limit  The data transmission rate limit in kbps.
   89 6.3.3  QoS Port Shaping  QoS port shaping supports traffic shaping of the Ethernet interface.Input the shaping rate and burst size to enforce QoS rule on each interface. If "Shaping Rate" is set to "-1", it means no shaping and "Burst Size" will be ignored.    Click Apply/Save to apply and save the settings.
   90 6.4 Routing    The following routing functions are accessed from this menu: Default Gateway, Static Route, Policy Routing, and RIP.  NOTE:   In bridge mode, the RIP menu option is hidden while the other menu options are shown but ineffective.  6.4.1 Default Gateway The default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected. Priority order can be changed by removing all and adding them back in again.    Click Apply/Save to apply and save the settings.
   91 6.4.2 Static Route This option allows for the configuration of static routes by destination IP.  Click Add to create a static route or click Remove to delete a static route.    After clicking Add the following will display.       IP Version: Select the IP version to be IPv4.   Destination IP address/prefix length: Enter the destination IP address.   Interface: Select the proper interface for the rule.   Gateway IP Address: The next-hop IP address.   Metric: The metric value of routing. After completing the settings, click Apply/Save to add the entry to the routing table.
   92 6.4.3 Policy Routing This option allows for the configuration of static routes by policy.  Click Add to create a routing policy or Remove to delete one.    On the following screen, complete the form and click Apply/Save to create a policy.      Field  Description Policy Name  Name of the route policy Physical LAN Port  Specify the port to use this route policy Source IP  IP Address to be routed Use Interface  Interface that traffic will be directed to Default Gateway IP  IP Address of the default gateway
   93 6.4.4 RIP To activate RIP, configure the RIP version/operation mode and select the Enabled checkbox  for at least one WAN interface before clicking Save/Apply.
   94 6.5 DNS  6.5.1 DNS Server Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. DNS Server Interfaces can have multiple WAN interfaces served as system DNS servers but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected. Priority order can be changed by removing all and adding them back in again.      Click Apply/Save to save the new configuration.
   95 6.5.2 Dynamic DNS The Dynamic DNS service allows you to map a dynamic IP address to a static hostname in any of many domains, allowing the NexusLink 3240 to be more easily accessed from various locations on the Internet.    To add a dynamic DNS service, click Add. The following screen will display.    Click Apply/Save to save your settings.  Consult the table below for field descriptions.  Field  Description D-DNS provider  Select a dynamic DNS provider from the list Hostname  Enter the name of the dynamic DNS server Interface  Select the interface from the list Username  Enter the username of the dynamic DNS server Password  Enter the password of the dynamic DNS server
   96 6.5.3 DNS Entries The DNS Entry page allows you to add domain name and IP address pairs desired to be resolved by the DSL router.   Choose Add or Remove to configure a DNS Entry. The entries will become active after save/reboot.   Enter the domain name and IP address that needs to be resolved locally, and click the Add Entry button.
   97 6.5.4 DNS Proxy/Relay DNS proxy receives DNS queries and forwards DNS queries to the Internet. After the CPE gets answers from the DNS server, it replies to the LAN clients. Configure DNS proxy with the default setting, when the PC gets an IP via DHCP, the domain name, Home, will be added to PC’s DNS Suffix Search List, and the PC can access route with “Comtrend.Home”.     Click Apply/Save to apply and save the settings.
   98 6.6 DSL  The DSL Settings screen allows for the selection of DSL modulation modes.   For optimum performance, the modes selected should match those of your ISP.      DSL Mode  Data Transmission Rate - Mbps (Megabits per second) G.Dmt  Downstream: 12 Mbps   Upstream: 1.3 Mbps G.lite  Downstream:  4 Mbps   Upstream: 0.5 Mbps T1.413  Downstream:  8 Mbps   Upstream: 1.0 Mbps ADSL2   Downstream: 12 Mbps   Upstream: 1.0 Mbps AnnexL   Supports longer loops but with reduced transmission rates ADSL2+   Downstream: 24 Mbps   Upstream: 1.0 Mbps AnnexM   Downstream: 24 Mbps   Upstream: 3.5 Mbps VDSL2  Downstream: 100 Mbps   Upstream: 60 Mbps   VDSL Profile  Maximum Downstream Throughput- Mbps (Megabits per second) 8a  Downstream 50  8b  Downstream 50 8c  Downstream: 50
   99 8d  Downstream: 50 12a  Downstream: 68 12b  Downstream: 68 17a  Downstream: 100 30a  Downstream: 100 Mbps      Upstream: 100 Mbps Options  Description US0  Band between 20 and 138 kHz for long loops to upstream Bitswap Enable  Enables adaptive handshaking functionality SRA Enable  Enables Seamless Rate Adaptation (SRA) G997.1 EOC xTU-R Serial Number Select Equipment Serial Number or Equipment MAC Address to use router’s serial number or MAC address in ADSL EOC messages 6.7 DSL Bonding This page displays the bonding status of the connected xDSL line.
   100 6.8 Interface Grouping  Interface Grouping supports multiple ports to PVC and bridging groups. Each group performs as an independent network. To use this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button.  The Remove button removes mapping groups, returning the ungrouped interfaces to the Default group. Only the default group has an IP interface.    To add an Interface Group, click the Add button. The following screen will appear.  It lists the available and grouped interfaces. Follow the instructions shown onscreen.
   101    Automatically Add Clients With Following DHCP Vendor IDs:  Add support to automatically map LAN interfaces to PVC's using DHCP vendor ID (option 60). The local DHCP server will decline and send the requests to a remote DHCP server by mapping the appropriate LAN interface. This will be turned on when Interface Grouping is enabled.  For example, imagine there are 4 PVCs (0/33, 0/36, 0/37, 0/38). VPI/VCI=0/33 is for PPPoE while the other PVCs are for IP set-top box (video). The LAN interfaces are ETH1, ETH2, ETH3, and ETH4.    The Interface Grouping configuration will be:  1. Default: ETH1, ETH2, ETH3, and ETH4. 2. Video: nas_0_36, nas_0_37, and nas_0_38. The DHCP vendor ID is "Video".
   102 If the onboard DHCP server is running on "Default" and the remote DHCP server is running on PVC 0/36 (i.e. for set-top box use only). LAN side clients can get IP addresses from the CPE's DHCP server and access the Internet via PPPoE (0/33).  If a set-top box is connected to ETH1 and sends a DHCP request with vendor ID "Video", the local DHCP server will forward this request to the remote DHCP server. The Interface Grouping configuration will automatically change to the following:  1. Default: ETH2, ETH3, and ETH4 2. Video: nas_0_36, nas_0_37, nas_0_38, and ETH1.

Navigation menu