Condeco PN41831 Infra-red sensor User Manual Condeco Sense Proposal for Company

Download:
Mirror Download [FCC.gov]
Document ID	2370448
Application ID	9xM8iXR9UIlomaCCLFue7Q==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	24.77kB (309678 bits)
Date Submitted	2014-08-27 00:00:00
Date Available	2014-08-27 00:00:00
Creation Date	2014-06-25 11:24:16
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2014-08-12 14:31:58
Document Title	Condeco Sense Proposal for [Company]
Document Creator	Microsoft® Office Word 2007
Document Author:	Peter Otto

Condeco Sense
User Manual
PN41831
Version 1.0 prepared by Condeco
Manufacturer:NOTE Electronics (Dongguan) Ltd
Contents
Operational Description ............................................................................................................................ 3
Primary Function ................................................................................................................................... 3
Block Diagram ........................................................................................................................................ 3
Sensor Registration .................................................................................................................................... 4
Condeco Sense
Page 2 of 4
Operational Description
The sensor contains a passive infra-red sensor and a wireless transmitter on 2.4 GHz IEEE
802.15.4. The device is battery powered using a 9Volt PP3 battery.
The device can also be powered using a micro usb connection and a low voltage power
supply. The power supply is not under tests as this is not supplied with the device
Primary Function
The device under test contains a passive infra-red detector that detects motion and
transmits the details on the number of activations to a central system every 5 minutes. The
transmission is intended for the recording of activity and is not intended as a live monitoring
solution.
The sensor is battery powered and is normally located under a desk or within a workspace.
Block Diagram
EUT
EUT Sensor
Condeco Sense
Not EUT
Gateway Reciver
Page 3 of 4
Sensor Registration
1. Ensure the sensor is powered using a 9V battery.
2. Ensure that the sensor is within range of the gateway sensor.
3. Using the end if a paper clip or similar tool, activate the registration switch to register
the sensor onto the network. When depressed the LED’s will illuminate and an entry
will appear in the gateway software table view as described in step 11 of the
software installation section.
Condeco Sense
Page 4 of 4
FCC ID: 2ACMLPN41831
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment。
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Language                        : en-GB
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : Peter Otto
Title                           : Condeco Sense Proposal for [Company]
Create Date                     : 2014:06:25 11:24:16+01:00
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2014:08:12 14:31:58+08:00
Metadata Date                   : 2014:08:12 14:31:58+08:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:587b6d81-36f3-42bb-b918-5deada367e2c
Instance ID                     : uuid:df86d9c5-c35e-4ec9-a579-a9b5f7c72e25
Page Count                      : 5
Author                          : Peter Otto

EXIF Metadata provided by EXIF.tools