Contec DS540-MPCI6 Wireless LAN MiniPCI Card User Manual Chapter1 General Description

Contec Co., Ltd. Wireless LAN MiniPCI Card Chapter1 General Description

Contents

User Manual

IEEE802.11a/b/g Wireless LAN MiniPCI Module
FX-DS540-MPCI6
User’s Manual (Installation Manual)
CONTEC CO., LTD.
Chapter 1: General Description
This document contains the specifications pertinent to the wireless LAN module (FX-DS540-MPCI6),
which comply with IEEE802.11a, IEEE802.11b and IEEE802.11g.
FX-DS540-MPCI6 is used attaching in the wireless LAN access point.
Features
2.4GHz Wireless LAN module
・ IEEE802.11b and IEEE802.11g compatible
・ BPSK, QPSK, CCK, and DSSS modulation schemes supported Data rates 1, 2, 5.5 and 11Mbps
・ BPSK, QPSK, 16QAM, 64QAM and OFDM modulation schemes supported Data rate 6, 9, 12, 18,
24, 36, 48 and 54Mbps
・ Coax. RF connectors: HIROSE U.FL equivalent
5GHz Wireless LAN module
・ IEEE802.11a compatible
・ BPSK, QPSK, 16QAM, 64QAM and OFDM modulation schemes supported Data rate 6, 9, 12, 18,
24, 36, 48 and 54Mbps
・ Coax. RF Connectors : HIROSE U.FL equivalent
System Functions
・ Low power sleep mode control
・ MiniPCI Interface
・ Radio circuit ON/OFF (RF Disable)
Chapter 2: Characteristics
Table1: Mechanical Characteristics
Dimensions 31.3 x 59.6 x 2.4 (mm)
Weight 10g
Figure1: FX-DS540-MPCI6
25.5
59.6
(mm)
Table2: Electrical Characteristics
Supply voltage Vcc Nominal : 3.3V
Extreme : 3.3V +/- 10%
Storage temperature
Humidity
-20 to 80 deg.C
10 to 90
Operating Temperature
Humidity
0 to 70 deg.C
10 to 90%no-condensing)
Chapter 3: Setup
FX-DS540-MPCI6 is used attaching in the wireless LAN access point. The wireless LAN access point is
restricted only to CONTEC products.
As an example, the case where it attaches in FX-DS540-STB-NR52 is introduced.
A
ttach a coaxial cable and fix.
(2 places)
Coaxial cable:
U.FL-2LP-04N1-A-(80) (HIROSE)
Fix with a screw lock. (2places)
Figure2: How to attach in FX-DS540-STB-NR52
-
-
-
Chapter 4: Notes
When FX-DS540-MPCI6 is installed in the wireless LAN access point, the following remarks are
to be considered:
1. FX-DS540-MPCI6 is designated its own FCC ID Number: PQRDS540-MPCI6 and IC
Number:4564A-MPCI6; therefore, the FCC ID and IC Number should be appeared on the
label on the exterior of the wireless LAN access point unless it is visible from outside.
Such label on the exterior should include a statement, either “Contains Wireless LAN
Module FCC ID: PQRDS540-MPCI6, IC Number: 4564A-MPCI6” or “Contains FCC ID:
PQRDS540-MPCI6, IC Number: 4564A-MPCI6”.
2. FX-DS540-MPCI6 is in compliance with the requirements of sub-sections 15.203, 15.205,
15.207, 15.209, 15.247 and 15.407 of FCC Rules Part 15. FX-DS540-MPCI6 is to be
installed in accordance with their requirements.
3. User Manual of the wireless LAN access point, in which is FX-DS540-MPCI6 installed, will
include the following statements required by FCC.
- FCC WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment
- This device complies with Part 15 of the FCC Rules and RSS-Gen of the IC Rules.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
In according with 47 CFR Part15.407 (e) U-NII devices operating in
5.15-5.25GHz frequency bands are restricted to indoor operations only.
This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for
uncontrolled equipment and meets the FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65. This equipment should be installed and
operated with at least 20cm and more between the radiator and person’s body
(excluding extremities: hands, wrists, feet and legs).
4. The installers must ensure that the public is not exposed to radio frequency energy levels in
excess of FCC guidelines in accordance with FCC Rules: Part 15 and FCC OET Bulletin 65,
Supplement C.
5. The installer of this radio equipment must ensure that antenna is located or pointed such that
it does not emit RF field in excess of Health Canada limits for the general population; consult
Safety Code 6, obtainable from Health Canada's website www.hc-sc.gc.ca/rpb
6. This class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Navigation menu