Continental Advanced Antenna TRANSCVRP01 Transceiver P001 User Manual Kathrein Briefkopf
KATHREIN Automotive GmbH Transceiver P001 Kathrein Briefkopf
Users Manual
Page 1
Bluetooth LE Transceiver
TRANSCVRP01
PORSCHE Part Number: 9Y0.051.515
Kathrein Part Number: 50110316
Page 2
Contents
1. Introduction ........................................................................................................................................ 3
2. Installation Options ............................................................................................................................ 3
3. Antenna Kitting ................................................................................................................................... 4
4. Technical Specifications ...................................................................................................................... 4
5. Safety and Recommendations ............................................................................................................ 5
Page 3
1. Introduction
The TRANSCVRP01 is an automotive ECU with an integrated Bluetooth LE transceiver for special
usage. The Bluetooth circuit and electronics are designed to tunnel a not public described data
stream via Bluetooth generic protocol. The device rejects any communication requests from
Bluetooth devices not supporting the nonpublic payload format. The device is fully integrated to the
electronics of the car and is connected with the CAN-Bus of the car to communicate with the rest of
the ECUs.
The device will be integrated in the car only by the car-manufacturer or in case of replacement by a
professional garage. The end-user does not have to do any installations or adjustments. There will
be no aftermarket modules available since the device needs to have a full range of ECUs available
to communicate with.
2. Installation Options
Example for a principle setup in a car.
The BT-Transceiver is designed for in-car use only. It is designed according the detailed specification
of the OEM (car-manufacturer). It MUST be well integrated into the automotive environment
(Tambient max. 85 °C) and needs to be installed by the OEM or in case of replacement by a professional
garage. Only the antennas listed at the Antenna Kitting section are allowed to be used along with
this BT-Transceiver.
Page 4
3. Antenna Kitting
Bluetooth Antenna Options: PORSCHE PART No.
Antenna Bluetooth 9Y0.051.506
4. Technical Specifications
General Specifications
Supported Bands
Band
Frequency
Service
Supported
[MHz]
ISM-Band
2402 – 2480
BTLE
Output Power
Output Power
Max. Value
Unit
Output 1
-4
dBm
Output 2
-4
dBm
Each device is individually tested and factory set to ensure FCC compliance and cannot be
adjusted without factory reprogramming or disabling the hardware.
Model Number
TRANSCVRP01
Antenna Connectors
FAKRA (male) DIN 72594-1/ISO 20860-1
Impedance
50 Ohm
DC Connector
MQS-Type
Power Requirements
DC 9 V - 16 V; 100 mA
Page 5
5. Safety and Recommendations
WARNING: The TRANSCVRP01 is designed for in-car use only. It MUST be well integrated
into the automotive environment (Tambient max. 85 °C) and needs to be installed
by the OEM (car-manufacturer) or in case of replacement by a professional
garage.
WARNING: Only the antennas listed at the Antenna Kitting section are allowed to be used
along with the TRANSCRVP01. The use of other antennas will cause the cease
of operating license of the BT-Transceiver.
This device complies with Part 15 of FCC rules. Operation is subject to two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by KATHREIN Automotive could void the
authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.