Continental Automotive Systems FANW Module with Multi-Band LTE, WCDMA, 2.4/5 GHz WLAN User Manual FANW OEM Integration Manual v3

Continental Automotive Systems, Inc. Module with Multi-Band LTE, WCDMA, 2.4/5 GHz WLAN FANW OEM Integration Manual v3

Contents

User Manual

Operation Guide for FANW Module 1. Product Overview FANW wireless module is a proprietary modem designed and manufactured by Continental Automotive Systems, Inc. The modem will be integrated into Data Connectivity Modules (DCMs) designed and produced by Continental for use by automotive OEMs. DCMs will binstalled into vehicles during the OEM’s factory assembly process and will not be accessible without use of special tools. Primary useconnections to Telematics Service Providers (TSP). FANW also supports WiFi used provide WiFi Hotspot functionality within the vehicle. Fig. 1. Top view of FANW module. Fig. 2. Bottom view of FANW module. FANW Feature Table: Feature Cellular Operating Bands WiFi Operating Bands and ProtocolsApplication Interface FCC ID: LHJ:FANW, IC: 2807E-FANW Operation Guide for FANW Module FANW wireless module is a proprietary modem designed and manufactured by Continental Automotive Systems, Inc. The modem will be integrated into Data Connectivity Modules (DCMs) designed and produced by Continental for use by automotive OEMs. DCMs will binstalled into vehicles during the OEM’s factory assembly process and will not be accessible without use of special tools. Primary use-cases are data-centric with data and voice connections to Telematics Service Providers (TSP). FANW also supports WiFi used provide WiFi Hotspot functionality within the vehicle. Fig. 1. Top view of FANW module. Fig. 2. Bottom view of FANW module.Description LTE FDD: 17, 4, 2 and 5 WCDMA: II and V WiFi Operating Bands and Protocols 2.4 GHz: - 802.11b - 802.11g - 802.11n 5 GHz: - 802.11a - 802.11n USB 4 wire UART 2 wire UART Audio: PCM ACC_POWER_ON pinHardware Reset Pin FANW wireless module is a proprietary modem designed and manufactured by Continental Automotive Systems, Inc. The modem will be integrated into Data Connectivity Modules (DCMs) designed and produced by Continental for use by automotive OEMs. DCMs will be installed into vehicles during the OEM’s factory assembly process and will not be accessible centric with data and voice connections to Telematics Service Providers (TSP). FANW also supports WiFi and will be Fig. 1. Top view of FANW module. Fig. 2. Bottom view of FANW module. ACC_POWER_ON pin
Data Services 2. Regulatory Compliance Notes FCC: This device complies with Part 15, Part 22(H), Part 24(E) and Part 27 of the FCC Rules. The FCC ID for this device is LHJ1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesired operation. Industry of Canada: This device complies with Industry Canada’s licensethe following two conditions:(1) This device may not cause interference; and(2) This device must accept any interference, including interference that may cause undesiredoperation of the device.” « Le présent appareil est conformeradio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et(2) l'utilisateur de l'appareil doit accepter tout brouillagebrouillage est susceptible d'en compromettre le fonctionnement. » This radio transmitter (2807Ethe antenna types listed below with the maximum permissible gain inot included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. FCC ID: LHJ:FANW, IC: 2807E-FANW BOOT_OK status pin MSG indicator pin JTAG Antenna interface (Primary, MIMO)LTE data rates: up to 100MBps DL / 50Mbps UL WiFi data rates: - 802.11a up to 54 Mbit/s- 802.11b up to 11 Mbit/s- 802.11g up to 54 Mbit/s- 802.11n up to 150 Mbit/sRegulatory Compliance Notes This device complies with Part 15, Part 22(H), Part 24(E) and Part 27 of the FCC Rules. The FCC ID for this device is LHJ-FANW. Operation is subject to the following two conditions:This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired« Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si lebrouillage est susceptible d'en compromettre le fonctionnement. » This radio transmitter (2807E-FANW) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. JTAG Antenna interface (Primary, MIMO) LTE data rates: up to 100MBps DL / 50Mbps 802.11a up to 54 Mbit/s 802.11b up to 11 Mbit/s Mbit/s 802.11n up to 150 Mbit/s This device complies with Part 15, Part 22(H), Part 24(E) and Part 27 of the FCC Rules. The FANW. Operation is subject to the following two conditions: 2. This device must accept any interference received, including interference that may cause on is subject to (2) This device must accept any interference, including interference that may cause undesired aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : radioélectrique subi, même si le FANW) has been approved by Industry Canada to operate with ndicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type,
« Le présent émetteur radio (2807Efonctionner avec les types d'antenne énumérés cimaximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. 3. Device Installation and User Manual The FANW module is a proprietary product designed and manufactured by ContinentalAutomotive Systems, Inc. for integration into telematics control units manufactured byContinental Automotive Systems, Inc. for automo i. The module is limited to installation ONLY in an integrated device manufactured by Continental Automotive Systems, Inc.ii. During manufacturing process of the integrated device, the module is soldered onto the pcb of the integrated device.iii. The integrated device must provide RF connectors to external antennas or RF traces to connect the FANW modules to antennas inside the integrated device. The typical reference design for the trace layout, including pcb stackdescribed and shown in a Figure 3 below: Typical RF trace layout between the FANW module and RF Connector:- Recommended RF Connector Type: Fakra- Main LTE/WCDMA antenna connector (MIMO1) is X203.o Recommended RF trace length is less than 40 mm.- Diversity LTE/WCDMA antenna connector (MIMO2) is X202.o Recommended RF trace length is less than 45 mm.- WiFi antenna connector is X201.o Recommended RF trace length is less than 50 mm. FCC ID: LHJ:FANW, IC: 2807E-FANW « Le présent émetteur radio (2807E-FANW) a été approuvé par Industrie Canada pour ctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.»Device Installation and User Manual The FANW module is a proprietary product designed and manufactured by ContinentalAutomotive Systems, Inc. for integration into telematics control units manufactured byContinental Automotive Systems, Inc. for automotive OEMs. The module is limited to installation ONLY in an integrated device manufactured by Continental Automotive Systems, Inc. During manufacturing process of the integrated device, the module is soldered onto the pcb of the integrated device. The integrated device must provide RF connectors to external antennas or RF traces to connect the FANW modules to antennas inside the integrated device. The typical reference design for the trace layout, including pcb stack-up and trace length is asdescribed and shown in a Figure 3 below: Typical RF trace layout between the FANW module and RF Connector: Recommended RF Connector Type: Fakra Main LTE/WCDMA antenna connector (MIMO1) is X203. Recommended RF trace length is less than 40 mm. LTE/WCDMA antenna connector (MIMO2) is X202. Recommended RF trace length is less than 45 mm. WiFi antenna connector is X201. Recommended RF trace length is less than 50 mm. FANW) a été approuvé par Industrie Canada pour dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain » The FANW module is a proprietary product designed and manufactured by Continental Automotive Systems, Inc. for integration into telematics control units manufactured by The module is limited to installation ONLY in an integrated device manufactured by During manufacturing process of the integrated device, the module is soldered onto the The integrated device must provide RF connectors to external antennas or RF traces to up and trace length is as
Fig. 3. Typical trace routing recommended for use with the FANW module. FCC ID: LHJ:FANW, IC: 2807E-FANW Fig. 3. Typical trace routing recommended for use with the FANW module. Fig. 3. Typical trace routing recommended for use with the FANW module.
- PCB Material: FR 4 - PCB design information:- Microstrip on layer 1 with ground on layer 2 / 50 ohm Single Ended Line/ 840 mm W 840 mm - Stripline on layer 2 with ground on layers 1&3 / 50 Ohm Single Ended Line/ 405 mm W Fig. 4. Recommended PCB stack FCC ID: LHJ:FANW, IC: 2807E-FANW PCB design information: Microstrip on layer 1 with ground on layer 2 / 50 ohm Single Ended Line/ 840 Stripline on layer 2 with ground on layers 1&3 / 50 Ohm Single Ended Line/ 405 Fig. 4. Recommended PCB stack-up information for use while integrating FANW module.Microstrip on layer 1 with ground on layer 2 / 50 ohm Single Ended Line/ 840 Stripline on layer 2 with ground on layers 1&3 / 50 Ohm Single Ended Line/ 405 information for use while integrating FANW module.
iv. Automotive OEM is responsible for ensuring that the endto remove or install module.v. The module is limited to installation in mobile applications, according to Parvi. No other operation configurations are allowed.vii. Changes or modifications to this system by other than a facility authorized by Continental could void authorization to use this equipment.viii. The module must be installed to provide a separation distance of at least 20 cm from all persons and must not be cotransmitter. ix. The integrator is responsible for fulfilling FCC and IC requirdevice. If Continental chooses to re-use modular approval, then the TCU shall be clearly labeled withan external label containing the integrated modem’s FCC ID. For example, the label caninclude text “Contains device with FCC I 4. Antenna requirements for use with FANW module: · The module must be installed to provide a separation distance of at least 20cm from allpersons and must not be co-located or operating in conjunction with any other antenna transmitter. · The FANW module is for use with external antennas ONLY.· For all LTE/WCDMA operating bands the maximum antenna gain is 6 dBi including cable loss. · For WiFi 2.4 GHz operating band the maximum antenna gain is 2 dBi including cable loss. · For WiFi 5 GHz operating band the maximum antenna gain is 6 dBi including cable loss.· The maximum gain of the antenna path (cable loss + antenna gain) shall not exceed the above mentioned values. This radio transmitter (FCC ID: LHJand Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are str « Le présent émetteur radio (ID: LHJIndustrie Canada pour fonctionner avec les types d'antenne énumérés cigain admissible maximal. Les types d'antennFCC ID: LHJ:FANW, IC: 2807E-FANW Automotive OEM is responsible for ensuring that the end-user has no manual instructions to remove or install module. The module is limited to installation in mobile applications, according to ParNo other operation configurations are allowed. Changes or modifications to this system by other than a facility authorized by Continental could void authorization to use this equipment. The module must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operate in conjunction with any other antenna or The integrator is responsible for fulfilling FCC and IC requirements for the integrated use modular approval, then the TCU shall be clearly labeled withan external label containing the integrated modem’s FCC ID. For example, the label caninclude text “Contains device with FCC ID: LHJ-FANW and IC: 2807E-FANAntenna requirements for use with FANW module: The module must be installed to provide a separation distance of at least 20cm from alllocated or operating in conjunction with any other antenna The FANW module is for use with external antennas ONLY. For all LTE/WCDMA operating bands the maximum antenna gain is 6 dBi including For WiFi 2.4 GHz operating band the maximum antenna gain is 2 dBi including cable For WiFi 5 GHz operating band the maximum antenna gain is 6 dBi including cable loss.The maximum gain of the antenna path (cable loss + antenna gain) shall not exceed the This radio transmitter (FCC ID: LHJ-FANW; IC: 2807E-FANW) has been approved by FCC and Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.« Le présent émetteur radio (ID: LHJ-FANW; IC: 2807E-FANW) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est user has no manual instructions The module is limited to installation in mobile applications, according to Part 2.1091(b). Changes or modifications to this system by other than a facility authorized by The module must be installed to provide a separation distance of at least 20 cm from all located or operate in conjunction with any other antenna or ements for the integrated use modular approval, then the TCU shall be clearly labeled with an external label containing the integrated modem’s FCC ID. For example, the label can FANW”. The module must be installed to provide a separation distance of at least 20cm from all located or operating in conjunction with any other antenna or For all LTE/WCDMA operating bands the maximum antenna gain is 6 dBi including For WiFi 2.4 GHz operating band the maximum antenna gain is 2 dBi including cable For WiFi 5 GHz operating band the maximum antenna gain is 6 dBi including cable loss. The maximum gain of the antenna path (cable loss + antenna gain) shall not exceed the ) has been approved by FCC and Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than ictly prohibited for use with this device. FANW) a été approuvé par dessous et ayant un e non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.» 5. Instructions to OEMs: Continental must instruct the automotive OEM and provide them to include the followinformation into the car user’s manual (i.e. for the DCM):1. End-users must be provided with transmitter/antenna installation requirements and operating conditions for satisfying RF exposure compliance:2. A separate section should clearly state “FCC RF Exposure requirements:”3. Required operating conditions for end users.4. The antenna used with this device must be installed to provide a separation distance of at least 20cm from all persons, and must nottransmitter, except in accordance with FCC multi5. The Maximum ERP/EIRP and maximum antenna gain required for compliance with Parts 15, 22H, 24E, and 27. 6. Clear instructions describing the other party’s responsibility to obtain station licensing. FCC ID: LHJ:FANW, IC: 2807E-FANW supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de Continental must instruct the automotive OEM and provide them to include the followinformation into the car user’s manual (i.e. for the DCM): users must be provided with transmitter/antenna installation requirements and operating conditions for satisfying RF exposure compliance: A separate section should clearly state “FCC RF Exposure requirements:” Required operating conditions for end users. The antenna used with this device must be installed to provide a separation distance of at least 20cm from all persons, and must not transmit simultaneously with any other transmitter, except in accordance with FCC multi-transmitter product procedures.The Maximum ERP/EIRP and maximum antenna gain required for compliance with Parts ing the other party’s responsibility to obtain station licensing.supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de Continental must instruct the automotive OEM and provide them to include the following users must be provided with transmitter/antenna installation requirements and The antenna used with this device must be installed to provide a separation distance of at transmit simultaneously with any other transmitter product procedures. The Maximum ERP/EIRP and maximum antenna gain required for compliance with Parts ing the other party’s responsibility to obtain station licensing.

Navigation menu