Continental Automotive Systems FANW Module with Multi-Band LTE, WCDMA, 2.4/5 GHz WLAN User Manual FANW OEM Integration Manual v3

Download:
Mirror Download [FCC.gov]
Document ID	3033317
Application ID	A0aEeA3k0QjXFXHceakKVQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	33.88kB (423460 bits)
Date Submitted	2016-06-20 00:00:00
Date Available	2016-12-15 00:00:00
Creation Date	2016-06-08 13:12:10
Producing Software	GPL Ghostscript 9.05
Document Lastmod	2016-06-08 13:12:10
Document Title	FANW_OEM_Integration_Manual_v3
Document Creator	PDFCreator Version 1.5.0
Document Author:	ais068

FCC ID: LHJ:FANW, IC: 2807E-FANW
Operation Guide for FANW Module
1. Product Overview
FANW wireless module is a proprietary modem designed and manufactured by Continental
Automotive Systems, Inc. The modem will be integrated into Data Connectivity Modules
(DCMs) designed and produced by Continental for use by automotive OEMs. DCMs will be
installed into vehicles during the OEM’s factory assembly process and will not be accessible
without use of special tools. Primary use
use-cases are data-centric
centric with data and voice
connections to Telematics Service Providers (TSP). FANW also supports WiFi and will be
used provide WiFi Hotspot functionality within the vehicle.
Fig. 1. Top view of FANW module.
Fig. 2. Bottom view of FANW module.
FANW Feature Table:
Feature
Cellular Operating Bands
WiFi Operating Bands and Protocols
Application Interface
Description
LTE FDD: 17, 4, 2 and 5
WCDMA: II and V
2.4 GHz:
- 802.11b
- 802.11g
- 802.11n
5 GHz:
- 802.11a
- 802.11n
USB
4 wire UART
2 wire UART
Audio: PCM ACC_POWER_ON pin
Hardware Reset Pin
FCC ID: LHJ:FANW, IC: 2807E-FANW
Data Services
BOOT_OK status pin
MSG indicator pin
JTAG Antenna interface (Primary, MIMO)
LTE data rates: up to 100MBps DL / 50Mbps
UL
WiFi data rates:
- 802.11a up to 54 Mbit/s
- 802.11b up to 11 Mbit/s
- 802.11g up to 54 Mbit/s
- 802.11n up to 150 Mbit/s
2. Regulatory Compliance Notes
FCC:
This device complies with Part 15, Part 22(H), Part 24(E) and Part 27 of the FCC Rules. The
FCC ID for this device is LHJ
LHJ-FANW.
FANW. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
Industry of Canada:
This device complies with Industry Canada’s license
license-exempt RSSs. Operation
on is subject to
the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.”
« Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement. »
This radio transmitter (2807E
(2807E-FANW)
FANW) has been approved by Industry Canada to operate with
the antenna types listed below with the maximum permissible gain iindicated.
ndicated. Antenna types
not included in this list, having a gain greater than the maximum gain indicated for that type,
are strictly prohibited for use with this device.
FCC ID: LHJ:FANW, IC: 2807E-FANW
« Le présent émetteur radio (2807E
(2807E-FANW)
FANW) a été approuvé par Industrie Canada pour
fonctionner
ctionner avec les types d'antenne énumérés ci
ci-dessous
dessous et ayant un gain admissible
maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain
maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
l'émetteur.»
»
3. Device Installation and User Manual
The FANW module is a proprietary product designed and manufactured by Continental
Automotive Systems, Inc. for integration into telematics control units manufactured by
Continental Automotive Systems, Inc. for automo
automotive OEMs.
i. The module is limited to installation ONLY in an integrated device manufactured by
Continental Automotive Systems, Inc.
ii. During manufacturing process of the integrated device, the module is soldered onto the
pcb of the integrated device.
iii. The integrated device must provide RF connectors to external antennas or RF traces to
connect the FANW modules to antennas inside the integrated device.
The typical reference design for the trace layout, including pcb stack
stack-up
up and trace length is as
described and shown in a Figure 3 below:
Typical RF trace layout between the FANW module and RF Connector:
- Recommended RF Connector Type: Fakra
- Main LTE/WCDMA antenna connector (MIMO1) is X203.
o Recommended RF trace length is less than 40 mm.
- Diversity LTE/WCDMA antenna connector (MIMO2) is X202.
o Recommended RF trace length is less than 45 mm.
- WiFi antenna connector is X201.
o Recommended RF trace length is less than 50 mm.
FCC ID: LHJ:FANW, IC: 2807E-FANW
Fig. 3. Typical trace routing recommended for use with the FANW module.
FCC ID: LHJ:FANW, IC: 2807E-FANW
PCB Material: FR 4
PCB design information:
- Microstrip on layer 1 with ground on layer 2 / 50 ohm Single Ended Line/ 840
mm W 840 mm
- Stripline on layer 2 with ground on layers 1&3 / 50 Ohm Single Ended Line/ 405
mm W
Fig. 4. Recommended PCB stack
stack-up information for use while integrating FANW module.
FCC ID: LHJ:FANW, IC: 2807E-FANW
iv. Automotive OEM is responsible for ensuring that the end
end-user
user has no manual instructions
to remove or install module.
v. The module is limited to installation in mobile applications, according to Part
Par 2.1091(b).
vi. No other operation configurations are allowed.
vii. Changes or modifications to this system by other than a facility authorized by
Continental could void authorization to use this equipment.
viii. The module must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co
co-located
located or operate in conjunction with any other antenna or
transmitter.
ix. The integrator is responsible for fulfilling FCC and IC requir
requirements
ements for the integrated
device.
use modular approval, then the TCU shall be clearly labeled with
If Continental chooses to re-use
an external label containing the integrated modem’s FCC ID. For example, the label can
include text “Contains device with FCC IID: LHJ-FANW and IC: 2807E-FAN
FANW”.
4. Antenna requirements for use with FANW module:
· The module must be installed to provide a separation distance of at least 20cm from all
persons and must not be co-located
located or operating in conjunction with any other antenna or
transmitter.
· The FANW module is for use with external antennas ONLY.
· For all LTE/WCDMA operating bands the maximum antenna gain is 6 dBi including
cable loss.
· For WiFi 2.4 GHz operating band the maximum antenna gain is 2 dBi including cable
loss.
· For WiFi 5 GHz operating band the maximum antenna gain is 6 dBi including cable loss.
· The maximum gain of the antenna path (cable loss + antenna gain) shall not exceed the
above mentioned values.
This radio transmitter (FCC ID: LHJ
LHJ-FANW; IC: 2807E-FANW)) has been approved by FCC
and Industry Canada to operate with the antenna types listed below with the maximum
permissible gain indicated. Antenna types not included in this list, having a gain greater than
the maximum gain indicated for that type, are str
strictly
ictly prohibited for use with this device.
« Le présent émetteur radio (ID: LHJ
LHJ-FANW; IC: 2807E-FANW)
FANW) a été approuvé par
Industrie Canada pour fonctionner avec les types d'antenne énumérés ci
ci-dessous
dessous et ayant un
gain admissible maximal. Les types d'antenn
d'antennee non inclus dans cette liste, et dont le gain est
FCC ID: LHJ:FANW, IC: 2807E-FANW
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur.»
5. Instructions to OEMs:
Continental must instruct the automotive OEM and provide them to include the following
follow
information into the car user’s manual (i.e. for the DCM):
1. End-users
users must be provided with transmitter/antenna installation requirements and
operating conditions for satisfying RF exposure compliance:
2. A separate section should clearly state “FCC RF Exposure requirements:”
3. Required operating conditions for end users.
4. The antenna used with this device must be installed to provide a separation distance of at
least 20cm from all persons, and must not transmit simultaneously with any other
transmitter, except in accordance with FCC multi
multi-transmitter
transmitter product procedures.
5. The Maximum ERP/EIRP and maximum antenna gain required for compliance with Parts
15, 22H, 24E, and 27.
6. Clear instructions describing
ing the other party’s responsibility to obtain station licensing.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 7
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:0c0a128f-3000-11e6-0000-92f0d2b24a0c
Producer                        : GPL Ghostscript 9.05
Keywords                        : ()
Modify Date                     : 2016:06:08 13:12:10-05:00
Create Date                     : 2016:06:08 13:12:10-05:00
Creator Tool                    : PDFCreator Version 1.5.0
Document ID                     : uuid:0c0a128f-3000-11e6-0000-92f0d2b24a0c
Format                          : application/pdf
Title                           : FANW_OEM_Integration_Manual_v3
Creator                         : ais068
Description                     : ()
Author                          : ais068
Subject                         : 

EXIF Metadata provided by EXIF.tools