Continental Automotive 5WK49147 Key User Manual

Continental Automotive GmbH Key

User Manual

Annex No.5 Technical Description Key: 5WK4 9147
Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49147 FCC ID:KR55WK49147 I:\POSTZULA\BMW\PL2_ID-ext\Technische_Doku_doc\Func_PL2ext_ID.doc Page 1 of 6 User Manual of the Siemens VDO Remote Control System Type: 5WK4 9145 5WK4 9146 5WK4 9147 5WK4 9148
Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49147 FCC ID:KR55WK49147 I:\POSTZULA\BMW\PL2_ID-ext\Technische_Doku_doc\Func_PL2ext_ID.doc Page 2 of 6 General description of the RF transmitter The RF remote control system consists of a RF transmitter and a RF receiver mounted within the control unit. The RF transmitter is mechanically integrated in the head of the key. This transmitter is used to transmit an information for locking or unlocking the vehicle by an unidirectional RF transmission line for normal remote operation by pressing a button. In general the following functions are provided: - Lock the car - Unlock the car - Unlock the trunk of the car Power supply The transmitter is provided with 1 Lithium battery (CR 2032) that gives a power supply of +3V. Buttons There are three buttons which enable to lock and unlock the doors and to unlock the trunk. During activation, the button is forced to the ground via a “pull-up” within the microcontroller. Typical usage pattern (for Europe only) 10 lock/unlock operations in 24 hours with typical transmission duration of 2 seconds → 0,42 lock/unlock operations with one hour Transmitter ON 0.84 seconds / hour Transmitter OFF 3599.16 seconds / hour Duty Cycle: TON / T (ON+OFF) x 100% = 0.84 / 3,600 x 100 % = 0.02%
Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49147 FCC ID:KR55WK49147 I:\POSTZULA\BMW\PL2_ID-ext\Technische_Doku_doc\Func_PL2ext_ID.doc Page 3 of 6 Block diagrams of the transmitter Button's PLL TransmitterIC9,84375 MHzCrystal125 kHzLF Circuit(L/C)315 MHzLoop AntennaµC for LF communication /RF - transmittionPower Supply2,2 to 3,3 VµC reference frequency616,54kHzTx, RF data4,807 kBit/sec315 MHzButton's PLL TransmitterIC13,5687 MHzCrystal125 kHzLF Circuit(L/C)µC for LF communication /RF - transmittionPower Supply2,2 to 3,3 VµC reference frequency847,5kHzTx, RF data5,3 kBit/sec434,2MHz434 MHzLoop Antenna
Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49147 FCC ID:KR55WK49147 I:\POSTZULA\BMW\PL2_ID-ext\Technische_Doku_doc\Func_PL2ext_ID.doc Page 4 of 6 Button's PLL TransmitterIC13,5687 MHzCrystal125 kHzLF Circuit(L/C)µC for LF communication /RF - transmittionPower Supply2,2 to 3,3 VµC reference frequency847,5kHzTx, RF data5,3 kBit/sec868,4MHz868,4 MHzLoop Antenna
Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49147 FCC ID:KR55WK49147 I:\POSTZULA\BMW\PL2_ID-ext\Technische_Doku_doc\Func_PL2ext_ID.doc Page 5 of 6 Variants Model Description 5WK4 9145 868.4MHz variant for Europe 5WK4 9146 434.2MHz variant for Europe 5WK4 9147 315MHz variant for USA 5WK4 9148 315MHz variant reduced power for Japan Technical Data Carrier frequency model 5WK4 9145: 868.4 MHz ± 0.05% Carrier frequency model 5WK4 9146: 434.2 MHz ± 0.05% Carrier frequency model 5WK4 9147: 315.0 MHz ± 0.05% Carrier frequency model 5WK4 9148: 315 MHz ± 0.05% Output power model 5KW4 9145/6/7: < 10 mW Field strength model 5WK49148: < 500µV/m @ 3m Type of modulation model 5KW4 9145/6/7: FSK Type of modulation model 5KW4 9148: ASK Method of frequency generation: PLL Number of channels: 1 Power supply: battery (CR2032) - Nominal voltage: 3 V - Lowest voltage: 2, 1 V - Highest voltage: 3, 3 V Type of battery: lithium Transmission range: <10 m Type of RF-antenna: Loop antenna Length of RF-antenna: 30, 35 mm
Siemens VDO Automotive AG SV C BC P2 RF IC: 267T-5WK49147 FCC ID:KR55WK49147 I:\POSTZULA\BMW\PL2_ID-ext\Technische_Doku_doc\Func_PL2ext_ID.doc Page 6 of 6 Label design Europe: (434 MHz) Europe: (868 MHz) Siemens VDO Siemens VDO 5WK4 9146 5WK4 9145 Japan: (315 MHz) Siemens VDO 5WK4 9148 USA/CAN: (315 MHz) Siemens VDO 5WK49147 IC: 267T-5WK49147 FCC ID:KR55WK49147 This device complies with part 15 of the FCC Rules and RSS-210. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation.

Navigation menu