Continental Automotive TIS-15 Tyre Pressure Monitoring Sensor User Manual TIS 15 Functional Description v6
Continental Automotive GmbH Tyre Pressure Monitoring Sensor TIS 15 Functional Description v6
User Manual
Tire Pressure Monitoring System
-Wheel Unit-
Type
TIS-15
- 2 -
1. SYSTEM OVERVIEW
The tire pressure monitoring system (referred as TG for Tire Guard = TG1C_G3) consists of
the following units:
- Tire guard wheel unit type TIS-15 which includes an integrated pressure, temperature and
acceleration sensor and a RF transmitter.
- LF receiver unit which includes a LF receiver (not described in this document)
The TG monitors a vehicle's tire pressure whilst driving or stationary. An electronic unit
(wheel unit) inside each tire, mounted to the valve stem, periodically measures the actual tire
pressure.
By means of RF communication, this pressure information is transmitted to the RF
transmitter.
2. TECHNICAL DESCRIPTION
Carrier frequency: 433.92 MHz
Number of channels: 1
Type of modulation: Frequency Shift Keying (FSK)
Amplitude Shift Keying (ASK)
Baud rate: 9600bps
Rated Output Power: < 10mW
Antenna: Internal
Voltage supply range: 2.1 up to 3.2V
Temperature Range: -40°C to +100°C
- 3 -
4. PICTURE
5. Label
- 4 -
5.1 EU Label
Continental
TIS-15
5.2 US label and owner manual entry
Continental TIS-15
FCC ID: KR5TIS-15
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for
help.
5.3 Canada label and owner manual entry
Continental Model: TIS-15
IC: 7812D-TIS15
Information Owner Manual:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
Interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Operation is subject to the following two conditions: (1) this device may not cause
Interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
- 5 -
5.4 Mexico warning statement on owner manual
Para su uso en México, la operación de este equipo está sujeta a las
siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia
perjudicial y (2) este equipo o dispositivo debe aceptar
cualquier interferencia, incluyendo la que pueda causar su operación
no deseada.