Continental Conair FF2115AT 900 MHz 40 Channel Cordless Phone with CID User Manual

Continental Conair Limited 900 MHz 40 Channel Cordless Phone with CID

Contents

User manual

STOP…DON’T TAKE ME BACK TO THE STORE.LOOK…FOR THE TOLL-FREE “HELP” TELEPHONE NUMBER.LISTEN…AS THE EXPERTS TALK YOU THROUGH THE PROBLEM.For immediate answers to your questions regarding operation,missing parts or installation, call theSOUTHWESTERN BELL FREEDOM PHONE® RETAIL SALES HELP LINE AT:1-800-366-0937Monday - Friday 8:30a.m. - 9:00p.m. ESTSaturday 8:30a.m. - 12:30p.m. ESThttp://www.swbfreedomphone.comSOUTHWESTERN BELL FREEDOM PHONE®7475 N. Glen Harbor Blvd., Glendale, AZ 85307FF2115AT IB- 3886 Printed in ChinaSouthwestern BellFreedom Phone®900MHz Cordless Telephone FF2115AT Owner’s ManualToll Free Helpline 1-800-366-0937http://www.swbfreedomphone.com
CONTENTSIMPORTANT SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS FOR BATTERIESNAME OF CONTROLS AND INDICATIONSFCC WANTS YOU TO KNOWINTRODUCTIONFEATURESBOX CONTENTSPREPARATIONOPERATING INSTRUCTIONSINSTALLATIONHANDSET BATTERY CHARGINGCALLER ID SETUPTELEPHONE OPERATIONCALLER ID OPERATIONTROUBLESHOOTINGPRODUCT CARESERVICELIMITED WARRANTY2345891010111314151922242526IMPORTANT SAFETY INSTRUCTIONSBEFORE USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY PRECAUTIONSSHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCKAND INJURY TO PERSONS, INCLUDING THE FOLLOWING:1. Read and understand all instructions.2. Follow all warnings and instructions marked on the product.3. Unplug this product from the wall telephone jack and power outlet before cleaning. Donot use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.4. Do not use this product near water, for example, near a bath tub, wash bowl, kitchensink, laundry tub, swimming pool, or in a wet basement.5. Do not place this product on an unstable cart, stand or table. The product may fall,causing serious damage.6. Slots or openings in the cabinet and the back and bottom are provided for ventilation, toprotect it from overheating. These openings must not be blocked or covered. The openingsshould never be blocked by placing the product on a bed, or other similar surface. This prod-uct should never be placed near or over a radiator or heat register.7. This product should be operated only from the type of power source indicated on themarking label. If you are not sure of the type of power supply to your home, consult yourdealer or local power company.8. Do not allow anything to rest on the power cord. Do not place this product where thecord will be damaged by persons stepping on it. 9. Do not overload wall outlets and extension cords, as this can result in fire or electric shock.10. Never push objects of any kind into this product through cabinet slots, as they maytouch dangerous voltage points or short out parts. This could result in fire or electric shock.Never spill liquid of any kind on the product.11. To reduce the risk of electric shock, do not disassemble this product. Instead, when serviceor repair work is required, take it to a qualified service technician. Opening or removing coversmay expose you to dangerous voltages or other risks. Incorrect reassembly can cause electricshock when the appliance is subsequently used.12. Unplug this product from the wall outlet and refer servicing to qualified service person-nel under the following conditions:a. When the power supply cord or plug is damaged or frayed.b. If liquid has been spilled into the product.c. If the product has been exposed to rain or water.d. If the product does not operate normally, and proper operating instructions have been fol-lowed, adjust only those controls that are covered by the operating instructions. Improperadjustment of other controls may result in damage and will often require extensive work by aqualified technician to restore the product to normal operation.e. If the product has been dropped or the cabinet has been damaged.f. If the product exhibits a distinct change in performance.13. Avoid using a telephone (other than a cordless type) during an electrical storm. Theremay be a remote risk of electric shock from lightning.14. Do not use the telephone to report a gas leak in the vicinity of the leak.15. Use only the power cord and batteries indicated in this manual. Do not dispose of batter-ies in a fire. They may explode. Check with local codes for possible special disposal instruc-tions.CAUTIONDanger of explosion if battery is incorrectly replaced.Replaced only with the same or equivalent type recommended by the manufacturer. 3
4SAFETY INSTRUCTIONS FOR BATTERIESSafety Instructions for BatteriesHandset Battery PackCAUTION:Use only a Southwestern Bell Freedom Phone® approved battery pack in the handsetof your FF2115 Cordless Telephone. To reduce the risk of fire or injury, always do thefollowing when replacing, discarding or charging batteries. When handling the batter-ies, be careful not to short the battery with conducting materials such as rings,bracelets, and keys. The battery or conducting material may overheat and cause burns.Use only the following type and size of battery pack:FOR HANDSET UNIT :a. GP40AAK3BMX 3.6V 400mAHr, GPI International Ltd orb. BYD D-2/3AA400BC 3.6V 400mAHr, BYD Battery Co.,Ltd orc. JB40AA2/3N3BMX 3.6V 400mAHr, JB Energy (HK) Ltd.a. Do not dispose of the battery pack in a fire. The cell may explode. Check with localcodes for possible special disposal instructions.b. Do not attempt to open or mutilate the battery pack. The chemicals are dangerousand may cause damage to the eyes or skin, and may be toxic if swallowed.c. Follow the charge instructions outlined in this manual.(See page 13)The EPA certified RBRC®* Battery Recycling Seal on the nickel-cadmium (Ni-Cd) bat-tery indicates that Southwestern Bell Freedom Phone® Retail Sales is voluntarily par-ticipating in an industry program to collect and recycle these batteries at the end oftheir useful life, when taken out of service in the United States or Canada. The RBRC®program provides a convenient alternative to placing used Ni-Cd batteries into thetrash or the municipal waste stream, which may be illegal in your areas. Please call 1-800-8-BATTERY for information on Ni-Cd battery recycling and disposal bans / restric-tions in your area. Southwestern Bell Freedom Phone® Retail Sales’s involvement inthis program is part of our commitment to preserving our environment and conservingour natural resources.*RBRC® is a trademark of the Rechargeable Battery Recycling Corporation.Save These InstructionsCONTAINS NICKEL-CADMIUM BAT-TERY. BATTERY MUST BE RECYCLEDOR DISPOSED OF PROPERLY.5NAME OF CONTROLS AND INDICATIONSHandset Controls, IndicatorsAntennaEarpieceLCD DisplayNew Call IndicatorFlashes to indicate thereare calls that have notbeen reviewedMemory ButtonUsed to store or recallnumbers in memoryDelete ButtonUsed for deleting CallerID entriesRedial ButtonRedials the last number oradds a pauseFlash ButtonUsed to access call wait-ing (if available)MicrophoneReceiver VolumeSwitchTo adjust the receiver vol-ume levelRinger On/Off SwitchCaller ID ReviewButtonsMemory scroll buttonsCaller ID Calls ButtonUsed to dial the displayednumberTalk ButtonUsed to make or to termi-nate callsKeypadNumber buttonsChannel ButtonUsed to select anotherchannel for clearer recep-tionMute ButtonRingerHeadset Jack
6LCD Display IndicatorNew Call /Call Counter Repeated CallIndicator Clock DateClock Ticker12-digit Number Line 12-character Text Line VIP IndicatorNew Call / Call CounterShows the amount of calls / new calls in standby mode.When there is a new call that has not been reviewed, the display will show “NEWCALL” and the New Call LED on the handset will blink.Repeated Call IndicatorLights up to indicate the displayed phone number called more than once.ClockShows the real time clock (AM/PM) format, or the time stamp of a Caller ID record.Clock TickerBlinks when real time clock is being displayed.DateShows the date (MM/DD) format, or the date stamp of a Caller ID record.12-digit Number LineDisplays the caller’s number, or displays your dialed digits.12-character Text LineDisplays caller’s name, call timer and system prompt (such as RINGING, TALK).VIP IndicatorIndicates that priority ringer has been set for the displayed number.7Base Unit Controls and IndicatorsTelephone Lineconnect the telephone linecord hereDC Inconnect the AC adaptor cordhereTone / Pulsesets the unit to pulse or tonedialingIn Use/Charge LEDLights when the handset is in Talk mode orthe handset is on the cradle and the bat-tery is being charged.Flashes when an incoming call is received.Page buttonused to locate thehandsetAntenna
FCC WANTS YOU TO KNOWThis equipment complies with Part 68 of the FCC rules. On the bottom of the base ofthis equipment is a label that contains, among other information, the FCC RegistrationNumber and Ringer Equivalence Number (REN) for this equipment. You must, uponrequest, provide this information to your telephone company.An FCC compliant telephone cord and modular plug is provided with this equipment.This equipment is designed to be connected to the telephone network or premises wiringusing a compatible modular jack which is Part 68 compliant. See Installation Instructionsfor details.The REN is useful to determine the quantity of devices you may connect to your tele-phone line and still have all of those devices ring when your telephone number iscalled. In most, but not all areas, the sum of the REN’s of all devices connected to oneline should not exceed five (5.0). To be certain of the number of devices you may con-nect to your line, as determined by the REN, you should contact your local telephonecompany to determine the maximum REN for your calling area.If your telephone equipment causes harm to the telephone network, the telephonecompany may discontinue your service temporarily. If possible, they will notify you inadvance. But if advance notice isn’t practical, you will be notified as soon as possible.You will be informed of your right to file a complaint with the FCC.Your telephone company may make changes in its facilities, equipment, operations, orprocedures that could affect the proper functioning of your equipment. If they do, youwill be notified in advance to give you an opportunity to maintain uninterrupted tele-phone service. If you experience trouble with this telephone equipment, disconnectfrom the network until the problem has been corrected or until you are sure that theequipment is not malfunctioning.This equipment may not be used on coin service provided by the telephone company.Connection to party lines is subject to state tariffs.This equipment is hearing aid compatible.Warning: Changes or modifications to this unit not expressly approved by the partyresponsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation.Some cordless telephones operate at frequencies that may cause interference tonearby TV’s and VCR’s. To minimize or prevent such interference, the base of the cord-less telephone should not be placed near or on top of a TV or VCR. If interference isexperienced, moving the cordless telephone farther away from the TV or VCR will oftenreduce or eliminate the interference. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interfer-ence to radio or television reception, which can be determined by turning the equip-ment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio TV technician for help. 9INTRODUCTIONABOUT THE FF2115ATThe FF2115AT is a 900 MHz Cordless Phone with Caller Identifier. Itis designed and engineered to exacting standards for reliability, long life,and outstanding performance.FEATURES• Caller ID (64 call data memory locations) with call waiting• 40 Channels (auto or manual selection)• LCD on the handset with three-language selection• 10-Number Two-touch Dial Memory• Direct dialing from caller list• Extended battery life• Digital security codingThe FF2115AT features include AutoTalk™ and AutoStandby™.AutoTalk™ allows you to answer a call by just removing the Handsetfrom the Base so you don’t have to waste time pushing buttons or flip-ping switches. AutoStandby™ allows you to hang up by simply return-ing the handset to the Base.The UltraClear Plus™ true compander circuitry virtually eliminatesbackground noise. This innovative technology, together with 40 differ-ent channels, provides you with the best possible reception during allyour conversations.TO PROTECT YOU AGAINST MISBILLED CALLS, THE FF2115AT HASRANDOM CODE™ DIGITAL SECURITY WHICH AUTOMATICALLYSELECTS ONE OF OVER 65,000 DIGITAL SECURITY CODES FORTHE HANDSET AND BASE UNIT. ALSO, THE AUTOSECURER™ FEA-TURE ELECTRONICALLY LOCKS YOUR PHONE WHEN THE HAND-SET IS IN THE BASE. TO GET THE MOST FROM YOUR FF2115AT,PLEASE READ THIS OPERATING GUIDE THOROUGHLY.8
10INTRODUCTION (CONT.)•Base unit•Handset with rechargeable battery•Owner’s manual•Memory card•Telephone line cordPreliminary PreparationTelephone Line Installation1. Never install telephone jacks during a lightning storm.2. Never install telephone jacks in wet locations unless the jack is specificallydesigned for wet locations.3. Never touch uninsulated telephone wires or terminals unless the telephone linehas been disconnected at the network interface.4. Use caution when installing or modifying telephone lines.Box Contents •AC adaptor with cord•Desk/Wall mounting bracket•Quick reference guide•Registration cardNOTE:a. Keep the shipping carton and packaging, in case you need to transport your phone.b. If any of these items are missing or damaged, contact your place of purchase.Modular OutletThe FF2115 cordless telephone operates from a standard 110/120 volt outlet. Thehandset is powered by a rechargeable battery pack. Batteries are charged automati-cally when the handset is placed in the cradle of the base unit.11INSTALLATIONDesk or Table Installation1. To connect Desk/Wall mount bracket in the desk/table position, simply align thebracket with the bracket slots on the Base until it is securely in place.2. Plug the AC adaptor cord into the 9V DC input jack on the Base unit.3. Plug one end of the telephone cord into the TEL LINE jack on the Base unit.4. Raise the antenna on the Base unit.5. Plug the other end of the telephone cord into the telephone wall jack.6. Plug the AC adaptor into a standard 120V AC wall outlet.NOTE:Use only with the AC adaptor supplied with FF2115.Place the telephone and power cords where they will notcreate a trip hazard, or where they could become chafedand create a fire or other electrical hazards.
12INSTALLATION (CONT.)Wall MountingThe FF2115 may be mounted on a wall phone plate or onto two screws (not included)that you fasten to the wall. For either type of installation, complete the following stepsfirst.1. In case of using the standard wall plate, this step is not necessary.Place the Desk/Wall bracket on the wall and mark the location of the screws. Installthe screws leaving 3/16” extending out from the wall. Use anchors to securescrews.2. To connect the Desk/Wall bracket in the wall mount position, simply align thebracket with the slots on the base until it is securely in place.3. Insert the AC adaptor into the back of the unit.4. Plug one end of the telephone line cord into the TEL LINE jack on the Base unit.5. Thread the adaptor cord and telephone line cord through the grooves in the backof the unit. The cord will exit from the bottom.DO NOT CONNECT THE AC ADAPTOR TO THE WALL POWER OUTLET YET.6. Plug the other end of the line cord into the wall jack.7. Mount the phone on the wallplate studs or on the screws as in step 1, and pressuntil the unit locks in place.8. Plug the AC adaptor into the power outlet.INSTALLATION (CONT.)Handset Battery Charging:The battery pack in the handset must be fully charged for about 10-14 hours beforeusing the telephone.After connecting to AC power, leave the handset unused in the cradle for ten to four-teen hours. Later, it will take less time for the battery to recharge. The IN USE/CHARGELED on the base will be lit when the handset is in the cradle.NOTE:a. When the battery gets low, the LCD display will show “BATTERY LOW”, and theunit will beep every 10 seconds.b. If the battery becomes low while you are on a call, you will be disconnected afterabout 3 minutes. Terminate the call quickly, and put the handset in the base torecharge the battery.c. The battery will hold its charge for several days out of the cradle, depending on use. NOTE:The handset will not ring when the ringer is in the “OFF” position. If the handset is outof the cradle, the LCD display will show “RINGING” during an incoming call.To Replace Batteries:1. Remove battery cover.2. Remove old battery.3. Plug the cord of the battery pack into the handset and placethe battery in the case.4. Slide battery cover until it clicks in place. Charge 10-14 hoursbefore first use.To maximize your battery’s life, we recommend that you periodically fully discharge thebattery, and then recharge it. To do this, unplug your phone line cord from the wallphone jack. Press the TALK button, and allow the handset to remain on for 10 to 12hours. Reconnect the phone cord to the wall phone jack. Return the handset to thebase and allow it to fully charge for 12 hours. If this process is completed monthly, itwill reduce the memory buildup that occurs from frequent partial charging. 13
14CALLER ID SETUPTo Set Language1. After the Handset battery is fully charged, the LCDdisplay will show “SET LANGUAGE”.2. Press the REVIEW “!” or “"” button to select ENG-LISH, FRENCH or SPANISH.3. Press the MEMO key to confirm the displayed lan-guage. The unit will to set area code.To Set Area Code1. Simply enter your area code number using the num-ber pad on the handset. Press the MEMO key toconfirm. 2. The unit will begin to set the contrast.NOTE: If there is no input within 20 seconds, the pro-gram will go back to the “SET LANGUAGE” step.To Set Contrast1. Press the “!” or “"” button to adjust the displaycontrast to the desired level (darker or lighter). Ifthere is no input within 20 seconds, the program willgo back to the “SET LANGUAGE” step.2. Press the MEMO key to confirm the displayed contrastlevel. The unit will show the default Time/Date (12:00 A.M.1/01). The time and date will be automatically updatedwhen the first incoming Caller ID call is received.NOTE:1. The Caller ID setup procedure will not begin until the handset is fully charged.2. To set up your FF2115 again, press and hold the “MEMO” button for 2 seconds inDate/Time screen.3. Your FF2115 will always stay in setup mode, until you complete the setup steps.However, it will still record the Caller ID information. This information can bereviewed only after set up is complete.4. To adjust the LCD display contrast while in the standby or review mode, press theFLASH button.15TELEPHONE OPERATIONTone / Pulse OperationThe FF2115 will operate on tone or rotary(pulse) systems.1. If your house is wired for rotary serv-ice, move the Tone/Pulse switch to thePulse position.2. If your house is wired for ToneService, move the Tone/Pulse switch tothe Tone position.3. If you are unsure of the type of dial-ing service you have, set the switch toTone. On the handset, press the TALKbutton and dial any digit on the keypad.If the dial tone persists, switch to Pulse.To disconnect, press the TALK buttonagain, or set the handset in the cradle.Digital Security SystemYour FF2115 Cordless Telephone isequipped with a digital security codingsystem to protect your base unit frombeing accessed by other cordless tele-phones.The code allows your base and handsetto recognize each other so that othercordless phones will not make calls onyour line.If the AC adaptor is disconnected or aloss of power occurs while the handset isaway from the base unit, the securitycode will be lost and the phone will beinoperable. If this occurs, reconnect theAC adaptor and return the handset to thebase unit so that the security code isreset.When the handset is not in the base, onlya handset having the identical securitycode and operating on the same channelcan access the base and use your phoneline.When the handset is in the base, noother handset, even those having theidentical security code and operating onthe same channel can access the baseand use your phone line.Digital security coding will also eliminatethe “false” ringing associated with cord-less telephones not equipped with thisfeature.
16TELEPHONE OPERATION (CONT.)40 Channel AutoScanOperationYour cordless telephone has 40 operat-ing channels. The phone will automati-cally search and select the clearest chan-nel when you press the TALK button. Ifyou hear noise or other interference dur-ing your conversation, you can manuallyselect a clearer channel by pressing andreleasing the CH button on the handsetto switch to another spare channel. Yourcall will not be interrupted.NOTE:You must be in usable range to changechannels. If you press the CH buttonwhen you are close to being out ofrange, you may lose the call. If thisoccurs, place the handset back into thebase for a few seconds to reset the secu-rity code and then make the call again.Receiver Volume ControlYour FF2115 allows you to adjust thehandset volume to a more comfortablelistening level. Slide the RECEIVER VOL-UME CONTROL on the side of the hand-set to NORM, MID or HIGH.Making a Call1. Make sure the base antenna is inupright position.2. Lift the handset and press the TALKbutton to be connected to the phoneline. The LCD display will show “TALK”and the TALK timer will start. The IN USE/CHARGE LED on the base will light. 3. After hearing a dial tone, dial thedesired number. Or you may predial the number (withoutpressing the TALK button), then pressthe CALLS button.4. If you misdial, simply press the TALKbutton, wait for a couple of seconds, andpress the TALK button again for a newdial tone.5. After your conversation is complet-ed, press the TALK button once to dis-connect the line, or return the handset tothe base.Receiving a CallWhen the phone rings:1. IF THE HANDSET IS OUT OF THECRADLE, press the TALK button. 2. IF THE HANDSET IS IN THE CRA-DLE, lift the handset. DO NOT press theTALK button, as you will be connectedautomatically.Temporary Tone (*):In Pulse dialing mode, you can accessbank facilities, telephone answeringmachines, etc., by simply pressing theTONE( * ) key to get into the tone modeand input the required tone codes. It willreset automatically after you end your call. 17TELEPHONE OPERATION (CONT.)NOTE:If you experience difficulty with placing orreceiving calls, the lost security codemay be the cause of the problem. Whenthis occurs, the handset can no longercommunicate with its base. The loss ofthe code can occur any of the followingways: if the battery is drained and needsrecharging; the handset is out of rangeof the base unit; the AC adaptor is dis-connected or a power loss has occurred;or anything that causes electrical inter-ference, for example multiple cordlesstelephones, baby monitors, televisions,VCR’s etc. Reset the security code byplacing the handset on the base for 10seconds. If that does not work, makesure the AC adaptor is connected. If nec-essary, unplug the AC adaptor from thepower source. Disconnect the battery for5 seconds and then reconnect. Place thehandset on the base and then replug theAC adaptor (see Troubleshooting).Ringer ControlIf you do not want the unit to ring, set theRINGER switch on the side of the hand-set to OFF. The handset will no longerring when a call is being received. Thehandset LCD display will show “RING-ING” when a call comes in.Out of RangeIf you try to place a call when you are toofar away from the base, you will hear stat-ic. If this occurs, move closer to the base.FlashYou can use your cordless telephonewith special services such as CallWaiting or Three Way Calling (Specialsubscription from your local telephonecompany is required). During a tele-phone conversation, you may hear atone or click, which indicates that you arereceiving another call. To speak to thesecond caller and put the first caller onhold, press the FLASH button. PressFLASH button again to return to the orig-inal call. You may also press the FLASHbutton to obtain a new dial tone.Page/Handset LocatorYou can send a page signal from thebase to the handset.Press the PAGE button on the base. Thehandset will beep for 3 seconds.Press and hold the PAGE button on thebase for 4 seconds, the handset willbeep for 60 seconds. Press any key onthe handset to stop paging.
18TELEPHONE OPERATION (CONT.)Memory FeatureYour FF2115 is equipped with 10 memo-ries for programming your most fre-quently dialed telephone numbers. Youcan store up to 16 digits in each of thememory locations 0 through 9 by follow-ing the steps outlined.A record of the numbers to be speed-dialed may be kept on the memory indexchart on page 24 in this manual. To Program Frequently CalledNumbers 1. Pick up the handset. DO NOTPRESS TALK button.2. Press the MEMO button; the LCDdisplay will show the number stored inMEM0 (zero).3. Press “!” or “"” buttons to select anavailable location.4. Dial phone number (up to 16 digits). Each TONE (*) entered uses one of theavailable digits. If you pause more than20 seconds in programming, the unit willexit the memory programming. If youaccidentally press a 17th digit, 3 errortone will sound, press DEL button toerase digits or press CH button to exit.4. Press the MEMO button again. theLCD display will show “LOCATION ? Mx”where “x” is the location you selected.5. Press MEMO button again to con-firm. The LCD display will show “MEMxSTORED” to confirm the number hasbeen successfully stored in memory.NOTE: Press CH button at any time willexit memory programming.To Retrieve Stored Numbers:1. Pick up Handset.2. Press TALK, and then MEMO button.3. Press the desired memory locationnumber. The number you programmedwill be dialed automatically.Or1. Press MEMO button, then press “!”or “"” buttons to select desired memorylocation.2. Press CALLS button. The numberyou programmed will be dialed automat-ically.To Change a Stored Number:1. Press MEMO button and “!” or “"”buttons to select memory location.2. Press DEL button to erase memory.The LCD display will show “ERASE ?”.3. Press DEL button to confirm.4. Reprogram the new number.RedialYour FF2115 remembers the last numberdialed. 1. Press the TALK button on the hand-set. When you hear a dial tone, press theREDIAL button. Or2. Press the REDIAL button, the lastnumber will be shown on the LCD dis-play. Press the CALLS button.PauseYou can insert a 4-second PAUSE intothe dialing of long distance numbers.Press the REDIAL button on the handsetduring dialing.CALLER ID OPERATIONReceiving a CallAfter the first ring, the caller’s name andtelephone number will display on theLCD. The New Call LED will flash untilyou review ALL your new calls.The Caller ID information (of up to 64callers) will be stored in the orderreceived. If the received call informationis the same as any of the new calls, theunit will display the “RPT” icon to indi-cate a repeat call. If the unit receivesmore than 64 calls, the oldest Caller IDinformation will be erased.NOTE:If you answer your incoming call beforethe second ring, the unit will not displaythe call information.Receiving Call Waiting Caller IDWhen you are on an existing phone call,your FF2115 will display incoming callwaiting Caller ID information.1. You will hear a beep and the tele-phone will be muted momentarily whilethe LCD display shows the Caller IDinformation of the second caller.2. When you access the call waitingcall, the Caller ID information will disap-pear and the Time/Day screen will be dis-played.IMPORTANT:You must subscribe to Call Waiting andCall Waiting Caller ID service from yourlocal telephone company in order toreceive Call Waiting Caller ID informa-tion.Reviewing New Call Records1. When Time/Date screen is dis-played, pressing the “!” or “"” buttonwill display the information for the lastnew call received.2. Continue pressing “!” or “"” but-ton to review all new call records in theorder the calls were received.When a name received exceeds 12 char-acters, the first 12 characters will beshown first with “"” showing on the righthand side. Press the “"” button to viewthe remaining characters.3. After the final call has been dis-played, press the “!” or “"” buttonagain. The New Call LED will stop blink-ing and the LCD will show “END NEWCALL”.NOTE:If you do not review all new calls, theTime/Date screen will display after 20seconds and the new call counter willshow the total number of new callsreceived (including those you justreviewed). 19
20CALLER ID OPERATION (CONT.)Reviewing All Call Records1. After you have reviewed all of the newcalls, press “!” or “"” buttons. The LCDdisplay will show the calls stored in memo-ry.2. After the last call record is reviewed,the LCD will show “-- END --”.Caller ID RedialTHE LOCAL AREA CODE MUST BEPROGRAMMED IN ORDER TO FULLYUTILIZE THE REDIAL FEATURE (SEEPAGE 14). The FF2115 allows you toredial a phone number stored in theCaller ID memory.1. Press the “!” or “"” button to selectthe Caller ID number that you want to dial.2. Press and release the CALLS buttonwhich activates the handset to dial thedesired number. The number will scrollacross the screen from right to left as it isdialed.To Stored a Caller ID Numberto Memory:1. Press “!” or “"” buttons to selectnumber from Caller ID list.2. Press MEMO button.3. Press MEMO button again to con-firm. The LCD display will show “LOCA-TION ?Mx”4. Press the location number. The LCDWith current telecom redialing situations,there are 4 redial options:(1) 7 digits without a 1 prefix(2) 7 digits with a 1 prefix(3) 10 digits without a 1 prefix, and(4) 10 digits with a 1 prefix.(1) 7 digits without a 1 :If the area code of the Caller ID numbermatches to the setting of your FF2115,redial your local call by pressing theCALLS button ONCE.(2) 7 digits with a 1 :If it is necessary to insert a 1 prefix toyour local call, simply press the CALLSbutton TWICE WITHIN 2 SECONDS.(3) 10 digits without a 1 :In some areas of the country, the areacode must be included even when dial-ing a local call. In this situation, set yourFF2115 area code to another 3 digits notbeing used in the U.S. i.e. 100,etc. Onceyour area code is programmed asabove, your FF2115 will record all 10 dig-its for every incoming call. Since the pre-fix 1 will be added automatically whendialing a 10 digit number, press theCALLS button TWICE WITHIN 2 SEC-ONDS for a local 10 digit call without aprefix 1.(4) 10 digits with a 1 :Since the prefix 1 will be added automat-ically when dialing a 10 digit number,simply press the CALLS button ONCE tomake your call.NOTE:Use caution when pressing the CALLSbutton. Press and release rapidly. If theCALLS button is pressed and held formore than 2 seconds, the VIP CALL fea-ture will be activated.21CALLER ID OPERATION (CONT.)Caller ID EraseTo Erase a Single Call1. Press the “!” or “"” button toreview the Caller ID records youreceived.2. Press DEL button to erase the calldisplayed; the display will show “ERASE?” on the bottom line.3. Press DEL button again; the Caller IDwill be erased and the display will showthe next message.NOTE:If the current message displayed is thelast message, then the display will backto standby mode.To Erase All Calls1. Press the “!” or “"” button toreview the Caller ID records receivedbefore erasing all calls.2. While the display is in standby mode,press and hold the DEL button for 2 sec-onds. The display will show “ERASE ALL?” on the bottom line.3. Press the DEL button; all VIEWEDcalls will be erased.NOTE:1. If there are messages that have notbeen reviewed, the “Erase All Calls”function cannot be performed.2. VIP calls will not be erased when youerase all calls.VIP CallsThe FF2115 allows you to create VIP callrecords. When a VIP call is received, 4beeps will sound between rings, to alertyou this is a VIP call.To Create a VIP Call record :1. Press the “!” or “"” button toselect the Caller ID which you want toassign a VIP ringer.2. Press and hold the CALLS button for2 seconds. The “VIP” icon is displayed.NOTE:4 beeps will also sound when the incom-ing VIP call is a Call Waiting call.To Remove a VIP Call :1. Press the “!” or “"” to select thecall you have marked “VIP”.2. Press and hold the CALLS button for2 seconds. The “VIP” icon will disappear.
22TROUBLESHOOTINGIf your FF2115 is not performing to your expectations, please try these simple steps :ProblemCharge light won’t come onwhen handset is placed inbase unit.No dial tone.Can’t make outgoing calls.Handset doesn’t ring.Suggestion• Make sure the AC Adapter is plugged intothe base unit and wall outlet.• Make sure the wall outlet is functioning.• Make sure the handset is properly seated inthe base unit.• Make sure the rechargeable battery pack isproperly placed in the handset.• Make sure that the charging contacts onthe handset and on the base unit are clean.• Charge the handset for 10 hours before ini-tial use.• Place the handset back into cradle for 5seconds.• Make sure the handset is fully charged. The IN USE/CHARGE LED should lightwhen the handset is in the cradle.• Make sure the Tone/Pulse switch is set tothe correct setting. If set to the Tone mode,switch to Pulse. You may have pulse dialingservice.• Make sure the Ringer On/Off switch on theside of the handset is set to the “On” posi-tion.• Rechargeable battery pack may be weak ornot fully charged. Charge the battery packfor 4-5 hours.• Make sure the base antenna is in theupright position.• The handset may be too far away from thebase unit.• Make sure the AC adaptor is plugged intothe base unit and wall outlet.• Make sure the wall outlet is functioning.• There may be too many telephonesinstalled on the same line. Contact yourlocal telephone company to determine themaximum number of extensions for yourcalling area.• Place the handset back into cradle for 5seconds. 23TROUBLESHOOTING (CONT.)ProblemCaller’s voice is too low.Conversation is interruptedfrequently. OrStatic noise is present duringconversation.When the handset is fullycharged for the first time, thedisplay does not show “SETLANGUAGE”, to begin theCaller ID setup sequence.Handset does not display anyCaller ID messages.The display screen is dim orblank.Unit is not receiving CallWaiting Caller ID calls.Telephone numbers are notdialed correctly from thecaller list.Suggestion• Switch the Receiver Volume Control on thehandset to higher level.• Move closer to the base.• Make sure the base antenna is in theupright position.• Press the CH button to switch to a clearerchannel.• Press the Caller ID “MEMO” button for 2seconds in the Date/Time screen. Then thedisplay will show “SET LANGUAGE”.• If that does not work, reset the handset byunplugging and then replugging in the bat-tery. Then the display will show “SET LAN-GUAGE”.• Check with your local telephone companyto make sure Call Waiting Caller ID serviceis being provided on your telephone line.• If you pick up the telephone before the firstcomplete ring, the caller information will notbe completely received.• Adjust the contrast.• Make sure you have subscribed to CallWaiting, Caller ID, and Call Waiting Caller IDservice from your local telephone company.• The Caller ID data may have been affectedby temporary noise or line conditions. Inthese cases, you may see the incorrectinformation on the display, such as NOCALLER ID, CID BLOCKED, ERROR, ablank screen, only the telephone number,or only the name.• Make sure you have set your local areacode.• Make sure the displayed telephone numberreflects the correct dialing situation (i.e. “1”before area code).
24PRODUCT CAREA. Avoid putting cordless phones nearheating appliances and devices that gen-erate electrical noise (motors, fluores-cent lamps, etc.).B. Avoid rough treatment of the phoneby placing the handset gently into thebase when hanging up. Avoid droppingthe handset.C. Clean your cordless telephone onlywith a soft cloth slightly dampened withwater or mild hand soap. Do not use anytype of solvent or abrasive cleaner.Before cleaning, always un-plug thephone from the wall outlet.D. Your cordless phone is not designedto be water resistant. Do not use thehandset in the rain, in the pool or in theshower. Do not install your base unit out-doors, near a sink, bath tub or shower.Do not expose to direct sunlight.E. Retain the original packaging shouldyou need to ship the phone at a laterdate.Additional InformationA. Connecting this telephone to a coinoperated telephone or party line is pro-hibited by law.B. If it is determined that your telephoneis malfunctioning, the FCC requires thatit be disconnected from the modular out-let until the problem has been corrected.For immediate answers to all your ques-tions regarding the operation of yourSouthwestern Bell Freedom Phone® callthe Consumer Hotline, toll free at(800)366-0937.Speed Dialing Numbers IndexLOCATION NUMBER LOCATION NUMBER012345678925SERVICEAccording to FCC regulations, this equipment, which has been certified and registeredby the FCC, may only be repaired by authorized persons. If repairs or adjustments aremade by an unauthorized person, the FCC certification may be voided. Should youencounter any problems, please call the Southwestern Bell Freedom Phone® toll-freeCustomer Help Line for assistance: 1-800-366-0937, Monday – Friday between thehours of 8:30 am – 9:00 pm (EST) and Saturday between the hours of 8:30 am - 12:30pm (EST). You can also visit our website at http://www.swbfreedomphone.com.FOR IN-WARRANTY SERVICE:Package your complete unit (including all adapters, line cords, and other accessories)and ship the unit postage prepaid* and insured (for your protection) to:SOUTHWESTERN BELL FREEDOM PHONE®DEPT.: Warranty Repair7475 N. Glen Harbor Blvd., Glendale, AZ 85307Be sure to include your return address, proof of purchase, a daytime phone number,$9.50 for postage and handling*, and a brief explanation of your difficulties.*NOTE: California residents need only provide proof of purchase and should call1-800-366-0937 for shipping instructions.FOR OUT-OF-WARRANTY SERVICE :Call our toll-free Help Line for the price of a replacement before returning your unit.Please follow all instructions for In-Warranty service (above) to return your unit, andmark the package: DEPT.: Out-of-Warranty.If you have called and know the cost of your replacement, please include this infor-mation with your unit for prompt service.QUESTIONS?STOP…DON’T TAKE ME BACK TO THE STORE.LOOK…FOR THE TOLL-FREE “HELP” TELEPHONE NUMBER.LISTEN…AS THE EXPERTS TALK YOU THROUGH THE PROBLEM.For immediate answers to your questions regarding operation, missing parts or instal-lation, call theSOUTHWESTERN BELL FREEDOM PHONE® HELP LINE AT:1-800-366-0937http://www.swbfreedomphone.com
LIMITED WARRANTY26This Southwestern Bell Freedom Phone® is warranted to the original purchaser to be freefrom defects in materials and workmanship under normal installation, use, and service for aperiod of one (1) year from the date of purchase as shown on the purchaser’s receipt.The obligation of Southwestern Bell Freedom Phone® Retail Sales under this warrantyshall be limited to repair or replacement (at our option) during the warranty period of any partwhich proves defective in material or workmanship under normal installation, use, and serv-ice, provided the product is returned to Southwestern Bell Freedom Phone® Retail Sales(address below) TRANSPORTATION CHARGES PREPAID (California residents call 1-800-366-0937 for shipping instructions). Products returned to us or to an Authorized ServiceCenter must be accompanied by a copy of the purchase receipt. In the absence of such pur-chase receipt, the warranty period shall be one (1) year from the date of manufacture. Toobtain service under this warranty, return the defective product to the service center nearestyou together with your sales slip and $9.50 for postage and handling (California residentsneed only provide proof of purchase). You may also have other warranty rights which varyfrom state to state. This warranty shall be invalid if the product is damaged as a result of defacement, misuse,abuse, neglect, accident, destruction, or alteration of the serial number, improper electricalvoltages or currents, repair alteration or maintenance by any person or party other than ourown service facility or an Authorized Service Center, or any use violation of instructions fur-nished by us.This warranty is also rendered invalid if this product is removed from the country in which itwas purchased, if it is used in a country in which it is not registered for use, and/or if it is usedin a country for which it was not designed. Due to variations in telephone systems and com-munications laws, this product may be illegal for use in some countries. Southwestern BellFreedom Phone® Retail Sales assumes no responsibility for damages or penalties incurredresulting from the use of this product in a manner or location other than that from which it isintended.This one-year limited warranty is in lieu of all other express warranties, obligations, or liabil-ities. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR APARTICULAR PURPOSE, SHALL BE LIMITED IN DURATION TO THE ONE-YEAR DURATIONOF THIS WRITTEN LIMITED WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ONHOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOTAPPLY TO YOU.IN NO EVENT SHALL WE BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUEN-TIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS ORIMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequentialdamages, so the above limitation or exclusion may not apply to you. This warranty gives youspecific legal rights, and you may also have other rights which vary from state to state.Covered under the following US patent : 5,263,084.SOUTHWESTERN BELL FREEDOM PHONE®7475 N. Glen Harbor Blvd., Glendale, AZ 85307

Navigation menu