Control4 C4DSCINT INTERIOR DOOR STATION User Manual

Control4 INTERIOR DOOR STATION

User Manual

™SpecificationsDimensions (H x W x D)7.19” (182 mm) x 5.13” (130 mm) x 2.3” (58 mm)Weight 3.25 lbs. (1.474 kg)Shipping Weight 3.25 lbs. (1.474 kg)Network 10/100 BaseT Ethernet (preferred) or WiFi (802.11 b/g/n)Voltages AC - 100V - 240V DC - 12V - 24VContacts (2 sets) DC: 48Vmaximum operation (low voltage)Relays (1) AC: 36V, 2A DC: 24V maximum operation (low voltage)Grounding RequirementsThe following table indicates which power options  require an earth ground.Power Type Earth Ground?AC Yes; required for safety.Power over Ethernet (PoE) No; do not connect.DC Recommended; not required.Front Panel DescriptionFigure 1. Front Faceplate1  Camera. 640 x 480 wide angle. Used for Video Intercom.2  Call button. Used to call the person inside the unit or in another room.3  Speaker. Used for Audio and Video Intercom.4  Screw holes (2). Used to screw the faceplate into the interior wall.5  Microphones (2). Used for Audio and Video Intercom.Supported Models• C4-DSC-EN-INT  Door Station - Interior AC, DC, POE & WiFi - Satin BlackBox ContentsCarefully unpack the Control4® Door Station from the box and ensure that the following items are included in the box. Remove the plastic protector from the faceplate. Contact your Control4 Dealer immediately if any parts are missing or if any components are damaged.• Control4 Door Station - Interior faceplate (model C4-DSC-EN-INT) • Two (2) mounting screws• Security screw tool• Warranty CardAccessories• Door Station Metal Back Box (C4-DSBB-M, sold separately)• Antenna Kit—WiFi/ZigBee 2.4 GHz, 26cm  (C4-AK-26cm, sold separately) • Antenna Kit—WiFi/ZigBee 2.4 GHz, 3m  (C4-AK-3M, sold separately)Door Station - Interior Setup Guide  13512445
™Inside Panel DescriptionFigure 2. Door Station, Inside Panel1  AC connection. Used to connect the wires for AC power.2  DC connection. Used to connect the wires for DC power.3  Contacts/Relays. Used to connect the wires for Control4 and third-party devices.NOTE: Use the contacts and relays for non-secure devices only. For example, don’t attach security gate wires to this terminal block.4  Ethernet connection. Supports PoE.5  Reset Button. Used to reset or factory restore the Door Station. Press the vertical bar to reset.Door Station - Interior  Setup Guide  Pre-Installation   1  Find the best location for the Door Station. See “Mounting Tips” below.2  Install the Door Station Back Box. See the Door Station Back Box Installation Guide for details.3  Determine which network and power options to use (see “Network Options” and “Power Options”).4  (WiFi only). Before the Door Station is fully installed, Control4 recommends to test the WiFi signal strength in Composer Pro’s System Manager; a strong, robust signal is required. See the Composer Pro User Guide for details.This device uses an Ethernet or WiFi network connection and can be powered using Power over Ethernet (PoE), AC, or DC.  A wired network connection is recommended for the best Video Intercom experience.  If it is not possible to use Ethernet, then please follow these guidelines for wireless.NOTES: (1) Video Intercom usage. Although this device supports b/g/n, 802.11 b is not recommended or supported for Video Intercom. (2) Wireless-N is recommended for Video Intercom. See “Wireless Network Limitations” below.Wireless Network LimitationsMany WiFi Access Points handle Multicasts (WiFi simultaneously sent to multiple devices, for example, when the Door Station broadcasts video to all stations) by slowing down transmission speed to the 1 Mb basic rate. This can cause overall WiFi congestion in the WiFi network during the broadcast. Video Intercom response times and images may degrade at each device. If a home requires a large number of WiFi Video Intercom devices, ensure that you have a robust WiFi network (possibly consisting of multiple access points).Mounting TipsFollow these tips for the best results.252 44444444444431
Power OptionsCAUTION! Do not attempt to use PoE, AC, and DC power at the same time. Choose only one  power option.ATTENTION! Ne pas tenter d’utiliser PoE, AC et DC en même temps. Choisir une seule option d’alimentation.The Door Station can be powered using one of these three (3) options: • Power over Ethernet (PoE). The Ethernet network connection for the Door Station is provided through the PoE Injector. No additional wiring is needed.• AC or DC. Used to power the Door Station when using an Ethernet (not PoE) or WiFi network connection.NOTE: Ethernet cable. Install the ferrite clamp on the Ethernet cable inside the back box.Backlit Button IndicatorThe Door Station button’s light can be turned on or o depending on what is required for the installation.  The backlit button may make it easier to see the button if it is dark inside the structure. Normally, the light on the button remains on or o depending on how it is configured in the system, however, it is also used to convey device status during certain times.  When the device is first powered on, the button will blink slowly until the device is ready to be used in the system. If the button continues to blink slowly for over three (3) minutes, then the device may be experiencing a problem and should be factory restored.  During a factory restore process the button will blink rapidly.Power and Network InstallationsChoose one of these six (6) options to connect the Door Station’s wiring:• Ethernet with PoE (preferred)• Ethernet with AC• Ethernet with DC1  Install the Door Station in a place where it will be protected from water.2  Do not expose the Door Station to direct sunlight. 3  Find the best location for the Door Station. See the Door Station Back Box Installation Guide for back box installation.a  Mount the Door Station where the video camera is aimed at an average person’s height so the person inside the building has a good view of the person calling in. b  Mount the Door Station so that the caller can comfortably speak into the microphone (about two (2) feet away or 60 cm). 4  Control4 does not recommend using wireless (WiFi) networking for an interior installation. If you must use WiFi, however, follow these guidelines:• The wireless access protocol (WAP) broadcast to the interior location must be strong.• Use Composer Pro’s System Manager to test the wireless signal after you’ve installed the Door Station, and then verify that the signal works correctly. See the Composer Pro User Guide for details.Network OptionsThe Door Station can be connected using one of these network types:• Standard Ethernet. For best results, this is the preferred option. Connect the Door Station to the RJ-45 LAN port on using the RJ-45 Ethernet cable.  • WiFi. The WiFi antenna will communicate with the LAN’s WAP. If the LAN has a WAP set up, no additional wiring is needed except for power. See “WiFi Antennas”  for details.IMPORTANT! (1) Control4 recommends to use an Ethernet connection rather than WiFi for the best communication with the Control4 system. (2) WiFi requires an antenna (sold separately).Please read the next sections, “Power Options” and   “Network and Power Installations” to choose an installation option that works best with the system before installing the Door Station.3
• WiFi with AC• WiFi with DC• WiFi with PoEOption 1 (Preferred): Ethernet Connection with a PoE Injector or a Third-Party Injector or SwitchThis option sets up Ethernet with PoE.PoE injects electrical current into the Ethernet cable using a PoE Injector (model #AC-POE1-B) or a third-party PoE solution to provide the Door Station with power and a network connection. To install the Door Station with a PoE and Ethernet connection using a PoE Injector:1  Plug the Ethernet cable into the Door Station (see Figure 3).2  See the section “Grounding Requirements” for details about earth grounding.Figure 3. Ethernet with PoE InjectorOption 2: Ethernet Connection with AC PowerThis option sets up Ethernet and AC power.To install the Door Station with Ethernet and AC power:1  Plug the Ethernet cable into the Door Station (see Figure 4). 2  Connect a ground wire from the Door Station to one of the back box lugs.3  Connect a second earth-ground or house-ground wire from the second back box lug to the home. See “Grounding Requirements” for details about earth grounding.4  Connect the neutral (N) (-) and hot (L) (+) wires to the AC power source for the Door Station according to the national and local electrical codes. TIP: The hot or ‘L’ (+) wire’s connector is closest to the bottom of the Door Station’s plate. 5  Your installation may require alternative wires and the use of a terminal block. Strip the power wires to 1/4” on the end if necessary.Figure 4. Ethernet with AC PowerOption 3: Ethernet Connection with DC PowerThis option sets up Ethernet and DC power.To install the Door Station with Ethernet and DC power:1  Plug the Ethernet cable into the Door Station (see Figure 5). 2  Connect a ground wire from the Door Station to one of the back box lugs. 3  Connect a second earth-ground or house-ground wire from the second back box lug to the home. See “Grounding Requirements” for details about 4Ethernet ConnectionGround WireEthernet CableAC Connections  (Hot and Load)
earth grounding.4  Connect the negative (-) and positive (+) wires to the DC power source for the Door Station according to the national and local electrical codes. TIP: The positive (+) wire’s connector is located on the bottom left side of the Door Station’s plate.5  Your installation may require alternative wires and the use of a terminal block (see Figure 5). Strip the power wires to 1/4” on the end if necessary.Figure 5. Ethernet with DC PowerOption 4: WiFi Connection with AC PowerThis option sets up WiFi and AC power.Ensure that you have WiFi in the home.NOTE: WiFi requires an antenna (sold separately).To install the Door Station with WiFi and AC power:1  Connect a ground wire from the Door Station to one of the back box lugs. 2  Connect a second earth-ground or house-ground wire from the second back box lug to the home. See “Grounding Requirements” for details about earth grounding.3  Connect the neutral (N) (-) and hot (L) (+) wires to the AC power source for the Door Station according to the national and local electrical codes. TIP: The hot or ‘L’ (+) wire’s connector is closest to the bottom of the Door Station’s plate.4  Your installation may require alternative wires and the use of a terminal block. Strip the power wires to 1/4” on the end if necessary.5  Attach the antenna (3m or 26cm) to the Door Station. See “WiFi Antenna Kit Installation” for details.6  Run the antenna wire through the back box hole (see Figure 6). Ensure that the wire doesn’t touch the back box.7  Align the antenna vertically to the wall outside the back box (26cm antenna) or run the antenna through the wall (3m antenna). See “WiFi Antennnas” for details.Figure 6.  WiFi with AC Power5Ethernet CableDC Connections  (Hot and Load)AC Connections  (Hot and Load)AntennaBack Box
Option 5: WiFi Connection with DC PowerThis option sets up WiFi and DC power.Ensure that you have WiFi in the home.NOTE: WiFi requires an antenna (sold separately).To install the Door Station with WiFi and DC power:1  Connect a ground wire from the Door Station to one of the back box lugs. 2  Connect a second earth-ground or house-ground wire from the second back box lug to the home. See “Grounding Requirements” for details about earth grounding.3  Connect the negative  (-) and positive (+) wires to the DC power source for the Door Station according to the national and local electrical codes. NOTE: The positive (+) wire’s connector is located on the bottom left side of the Door Station’s plate.4  Your installation may require alternative wires and the use of a terminal block. Strip the power wires to 1/4” on the end if necessary.5  Attach the antenna (3m or 26cm) to the Door Station. See “WiFi Antenna Kit Installation” for details.6  Run the antenna wire through the back box hole (see Figure 12). Ensure that the wire doesn’t touch the back box.7  Align the antenna vertically to the wall outside the back box (26cm antenna) or run the antenna through the wall (3m antenna).Figure 7.  WiFi with DC PowerOption 6: WiFi Connection with PoEThis option sets up WiFi and PoE.Ensure that you have WiFi in the home.NOTE: WiFi requires an antenna (sold separately).To install the Door Station with WiFi and PoE:1  Plug the Ethernet cable into the Door Station (see Figure 8).2  Connect a ground wire from the Door Station to one of the back box lugs. 3  Connect a second earth-ground or house-ground wire from the second back box lug to the home. See “Grounding Requirements” for details about earth grounding.4  Attach the antenna (3m or 26cm) to the Door Station. See “WiFi Antenna Kit Installation” for details.5  Run the antenna wire through the back box hole (see Figure 12). Ensure that the wire doesn’t touch the back box.6  Align the antenna vertically to the wall outside the back box (26cm antenna) or run the antenna through the wall (3m antenna).6DC Connections  (Hot and Load)Antenna
Figure 8.  WiFi with PoEAttach the Door StationAfter the back box, all wiring, cables, and antennas are installed, carefully insert the Door Station into the back box and the wall:1  On the front of the faceplate remove the tape that covers the camera hole.2  Align the Door Station’s top and bottom screw holes on the faceplate with the screw holes on the back box.3  Use the screws provided to attach the Door Station to the back box.4  To prevent dust from getting inside the Door Station, make sure the rubber gasket on the inside panel of the Door Station completely covers and seals the Door Station’s faceplate against the back box.Configure the Door StationTo configure the Door Station in Composer Pro: 1  Open Composer Pro.2  Double-click the Door Station driver to add it to a room in the project. 3  Identify the device to the project.(WiFi only) For your convenience, the Door Station driver includes a meter to check WiFi signal strength. Use System Manager in Composer Pro to configure the WiFi parameters. See the Composer Pro User Guide for details.Reset/Factory Restore the Door StationTo reset or factory restore the Door Station:1  Remove the faceplate and pull the Door Station out from the back box just enough to expose the Reset button (see Figure 2).2  While powered press the Reset button on the bottom of the Door Station to reset or restore the Door Station.• Quick press. Press to reset the Door Station.• Long press. Press until the button on the faceplate begins to blink rapidly. At that time, the factory restore starts. This action restores the Door Station to its factory default settings.3  When you are finished, insert the Door Station back into the back box and reattach the faceplate.WiFi Antennas (Optional)NOTE: Control4 does not recommend to install the Door Station using WiFi. The best option is to use Ethernet.Two (2) types of WiFi antenna kits are available for purchase: 26cm (dipole, best performance) or 3m (when you need to install the wire further away from the Door Station for a better WiFi signal).• Antenna Kit—WiFi/ZigBee 2.4GHz, 26cm (C4-AK-26cm, sold separately). Recommended for walls that do not have thick concrete or metal. See Figure 9 and “WiFi Antenna Kit Installation” for details.• Antenna Kit—WiFi/ZigBee 2.4GHz, 3m (C4-AK-3M, sold separately). Extend the range when walls have thick concrete or metal. See Figure 10 and “WiFi Antenna Kit Installation” for details.Figure 9.   26cm Antenna Kit7WiFi AntennaEthernet and PoE Connection
8Figure 10.   3m Antenna KitWiFi Antenna Kit Installation (Optional)Before you install the antenna:1  Make sure the Door Station is assembled. 2  Make sure the Door Station back box is installed in the wall. See the Door Station Back Box Installation Guide for details.Antenna Kit—WiFi/ZigBee 2.4GHz, 26cm  (C4-AK-26cm)1  Remove the antenna from its packaging.2  Attach the antenna’s plug to the RSMA connector on the Door Station (see Figure 11).Figure 11. Antenna to RSMA Connector3  Thread the other end of the antenna through the back wall of the back box (see Figure 12).Figure 12. Thread Antenna Through Back Box  4  Leave the other end of the antenna hanging outside the back box. Adjust it vertically for the best signal.5  Carefully insert the Door Station into the back box (see “Attach the Door Station”).Antenna Kit— WiFi/ZigBee 2.4GHz, 3m (C4-AK-3M)1  Attach the antenna’s plug to the RSMA connector on the Door Station (see Figure 11).2  Thread the other end of the antenna through the back wall of the back box and through the interior wall as needed (see Figure 12).3  Carefully insert the Door Station into the back box (see “Attach the Door Station”).Contact and Relay ConnectionsYou can connect devices to the contact ports or the relay ports (see Figure 13).CAUTION! Control4 does not support using earth ground for Contacts, as this could damage the Door Station.RSMA ConnectorAntennaAntenna
Figure 13. Contacts and RelaysConnect to a PortThe Door Station provides six (6) ports for use as two (2) contact sets and one (1) relay (see Figure 14).• Contact (2 sets). Terminal connector for one (1) dry contact closure, logic input connection, for gate control, etc. Provides power for small devices (12 V), signal input (SIG), return path (GND). The current, 100 mA, is shared across both sets of contacts.NOTE: Do not use contacts that are grounded. The Door Station only supports non-grounded contacts.• Relay (1). Terminal connector for one (1) normally closed or normally opened switchable connection for doorbell control (see Figure 15) or gate control. The set contains a connection for Normally Opened (NO), Normally Closed (NC), and Common (COM). Figure 14. Contact/Relay Locations1  To attach the wires to the contacts or relay, select one of the large bottom-row holes (see Figure 13; notice that the top row holes are smaller than the bottom-row holes).2  Using a small flat screwdriver, insert the 9screwdriver into the slot on the small block that sits between the two rows of holes adjacent to the port and push down firmly. The block will depress.3  Insert the wire. Ensure that the wire inserts all the way into the hole. 4  Release the screwdriver.Example WiringFigure 15. Relay Port: Normally Open (e.g., Doorbell)TroubleshootingBoot UpWhen the Door Station is booting up, if the button blinks and does not stop after three (3) minutes or longer, there is a problem with the device and it will have to be restored. See “Reset/Restore the Door Station” in this document.Factory RestoreTo restore the device to its default factory settings, see “Reset/Restore the Door Station” in this document.Security Best Practices The Door Station has connections for relays (to open doors, gates, etc.) and contacts. If installed without the proper security precautions, unauthorized access to the Door Station could provide access to Ethernet signals, Control4 signaling, and gate or door relays. Control4 advises Control4 Dealers to be aware of these risks and take all necessary precautions depending on each specific installation you will be doing. It is each Dealer’s sole responsibility to advise their customer at each installation of any security risks Contacts Relays
specific to such installation. Control4 makes no claims, representations or warranties regarding the security of this product and accepts no liability for any security risk attendant to a specific installation.1  The Door Station ships standard with security screws. Dealers are encouraged to use these screws, or even substitute alternate security screws per the Dealer’s or customer’s preference. Screw size is metric M3.5x.6-30L.2  Security gates or automatic doors should not be connected to the relay in the Door Station if mounted in an unsecured area; such relays could be accessed in the event of a breach of the device. Secure relay-driven devices should be connected to a more secure relay controller mounted behind a secure wall.3  Security devices, for example numeric keypads, should not be connected to the contact sensors in the Door Station if mounted in an unsecured area; such devices could be accessed in the event of a breach of the device. Security-sensitive devices should be connected to more secure contacts mounted behind a secure wall.4  Although the best video performance will be enabled by Ethernet connectivity, unauthorized access to the Door Station could provide access to the dwelling’s Ethernet network and corresponding personal data. There are alternatives to mitigate this risk. The Dealer should consider the following options:• Running Control4 on an isolated LAN from PCs on the network would limit exposure to personal data.• Running MAC address filtering on the router or switch to force a hacker to spoof the Door Station’s MAC address to gain access to the LAN.• Configuring the Door Station as WiFi instead of Ethernet would allow the Dealer to use robust WiFi security protocols, for example, WPA. NOTE: WiFi signals must be very strong and stable to support Video Intercom.• Routing the Ethernet cable to the Door Station through a secure, managed switch to limit data access from the Door Station.10Dealers should take time to assure they are not creating an unforeseen security risk for the customer, and any such risks should be discussed with the customer prior to the installation. Carefully consider with your customer any contacts or relays before connecting them to the Door Station, and what implications could arise if someone gained access to the rear of the Door Station. Also, think about what could happen if someone gained access to the Ethernet cable, and take necessary precautions to protect private customer information unless your customer is willing to assume these risks. Making available the proper security protections to a customer for their residence is the responsibility of the Control4 Installer.WarningsWARNING!  To avoid bodily harm, understand and follow these safety precautions before operating this Door Station:- Using worn-out or damaged power cords may result in electric shock or fire.- Always contact an authorized Control4 service provider for assistance if any repair or adjustment is required.Avertissement! Pour éviter des dommages physiques, comprenez et suivez ces mesures de sécurité avant d’actionner station de porte Control4® sans fil:- Utilisant usé ou endommagé les cordons de secteur peuvent avoir comme conséquence  la décharge électrique ou le feu.- Entrez en contact avec toujours un  fournisseur des services Control4® autorisé  pour l’aide si n’importe quelle réparation ou  ajustement est exigée.IMPORTANT! Improper use or installation can cause LOSS/DAMAGE OF PROPERTY.Important! L’utilisation ou l’installation inexacte peut causer LOSS/DAMAGE DE PROPRIÉTÉ.
©2012 Control4. All rights reserved. Control4, the Control4 logo, the Control4 iQ logo and the Control4 certified logo are registered trademarks or trademarks  of Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners.control4.com   |  ™IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See “Warranty.”Important! Utilisant ce produit en quelque sorte autre que décrit dans ce document vide votre garantie. De plus, Control4 n’est pas responsable d’aucun dommage encouru avec l’abus de ce produit. Voyez que «Warranty.»WARNING!  Before you install the Door Station switch o the circuit breaker or remove the fuse from the fuse box.AVERTISSEMENT! Pour l’endroit où vous installez station de porte, coupez le disjoncteur ou enlevez le fusible de la boîte de fusible.IMPORTANT!  Before you can complete these instructions below, you must have a Door Station back box installed according to the documentation provided in the back box kit. See “Accessories” for details.Important!  En coupant l’ouverture pour la boîte de mur, ne coupez pas l’ouverture trop grande. Soyez conservateur et agrandissez-avec précaution la comme nécessaire. Voyez que <<Accessories>>.Regulatory/Safety InformationTo review regulatory information for your particular Control4 products, see the information located on the Control4 website at: http://www.control4.com/regulatory/.WarrantyLimited 2-year Warranty. Go to http://www.control4.com/warranty for details.About This DocumentPart number: 200-00317, Rev. A  6/27/201211
™Requirements• Toolstoinstallthebackbox,suchasatapemeasure,pencil,hammerorscrewdriver• Nailsorscrews(4to6)• AntennaKits(optional,soldseparately)-Antenna,12”(C4-AK-26cm)-ExternalAntenna,10’,EWA2450M(C4-AK-3M)SpecificationsDimensions(HxWxD)6.1”x4.1”x3”(156mmx104mmx76mm)Weight 1.10lbs.Network EthernetorWiFi(802.11b/g/n)Grounding RequirementsThefollowingtableindicateswhichpoweroptionsrequireanearthground.Power Type Earth Ground?AC Yes,requiredforsafety.PowerOverEthernet(PoE) No.Donotconnect.DC Recommended;notrequired.Network and Power ConsiderationsThisdeviceusesanEthernetorWiFinetworkconnectionandcanbepoweredusingPoE,AC,orDC.NOTE:ItisrecommendedtouseEthernetratherthanWiFiforthebestnetworkconnectivity.SeetheDoor Station - Exterior Setup Guideforwiringinstallationdetails.Mounting TipsFollowthesetipsforbestresults.1  InstalltheDoorStationinaplacewhereitwillbeprotectedfromwater(e.g.,rain,sprinklers,etc.).2  DonotexposetheDoorStationtodirectsunlight.Forinstallationsindirectsunlight,theSatinNickelmodel(C4-DCS-EN-SN)willyieldtheleastamountofcolorfading.3  FindanappropriateexteriorlocationfortheDoorStation.AlsoseetheDoor Station - Exterior   Setup Guideforbackboxplacement.a  MounttheDoorStationwherethevideoSupported Model• C4-DSBB-E-MDoorStationMetalBackBoxFigure1.DoorStationBackBoxGeneral DescriptionControl4®providesabackboxtoaccommodatetheinstallationofaControl4DoorStation-Exterior(C4-DSC-EN-xx).Box ContentsUnpacktheDoorStationBackBoxandensurethefollowingitemsareincludedinthebox.ContactyourControl4Dealerimmediatelyifyoundanymissingordamagedcomponents.• Control4DoorStationBackBox(modelC4-DSBB-E-M)DoorStationBackBoxInstallationGuide1
™cameraisaimedatanaverageperson’sheightsotheviewercanseethepersoncallingin.b  MounttheDoorStationsothatthecallercancomfortablyspeakintothemicrophoneorabout18”to2’away(45cmx60cm).4  Itisnotrecommendedtousewireless(WiFi)foranoutsideinstallation.IfyouuseWiFi,followthesetips:• PlacetheDoorStationinalocationwherethewirelesssignal(WAPbroadcast)isstrong.• Placetheaccesspointinaclearlineofsightorlessthan100feet,ifpossible.• Placetheaccesspointwhereitwillhavetheleastnumberofwallstopassthrough.• Placetheaccesspointonthesecondlevelbyawindow.• UseComposerPro’s,SystemManagertotestthewirelesssignalafteryou’veinstalledtheDoorStation.• Verifythatthesignalworks.SeetheDoor Station - Exterior Setup Guide(whentheDoorStationisreleased)forWiFiinstallationinstructions.InstallationNOTES:(1)Placethebackboxbetweenstuds.Donotattempttoinstallabackboxoverawallstud.(2)ToconformtoNEMAsafetystandards,installastrain-reliefcord(soldseparately)inthepunchoutonthebackboxbeforeinsertingthewires.See“RegulatoryInformation”ortheNEMAwebsiteat:http://www.nema.org/stds/fordetails.DoorStationBackBoxInstallationGuideIMPORTANT!Makesurethebackboxprotrudesfarenoughout(0.118”or3mm)fromtheexteriorwallsurface(brick,rock,stucco,wood,concrete,etc.)toallowtheplateandgaskettosealtheDoorStation(seeFigure2).Figure2.BackBoxSideViewinWallwithDoorStationFaceplate1  FeedtheAC,DC,orPoEwiresthroughatabinthebackofthebackbox.SeetheDoor Station - Exterior Setup Guidetodetermineyourinstallationoption.2  Afterplacingthebackboxinsidethewall,securetheboxwithscrewsornails.3  Attachthegroundwirestothebackboxasneeded(see“GroundingRequirements”onpage1)andDoorStationplateinthelocationindicatedbythegroundsymbol(seeFigures3and4).Therearetwo(2)groundscrewsinthebackbox:one(1)forEarthgroundandone(1)forgroundingtheDoorStationfaceplatetothebackbox.2
Figure4.GoundWiresfromDoorStationtoBackBoxWarningsIMPORTANT!ImproperuseorinstallationcancauseLOSS/DAMAGEOFPROPERTY.Important!L’utilisationoul’installationinexactepeutcauserLOSS/DAMAGEDEPROPRIÉTÉ.WARNING!BeforeyouinstalltheDoorStationBackBoxusingAC,switchothecircuitbreakerorremovethefusefromthefusebox.AVERTISSEMENT!Pourl’endroitoùvousinstallezstationdeporteavecAC,coupezledisjoncteurouenlevezlefusibledelaboîtedefusible.Regulatory/Safety InformationToreviewregulatoryinformationforyourparticularControl4products,seetheinformationlocatedontheControl4websiteat:http://www.control4.com/regulatory/4  IfusingWiFi,theWiFiantennamustbeinstalledinthebackboxandextendoutsidethebox.NOTE:Donotallowanycontactoftheantennaelementtoanymetalsurfaceonthebackbox;otherwise,antennaperformancewilldiminish.Figure3.GroundWiretoDoorStationWARNING!ForACinstallation,failuretogroundthemetalbackboxandDoorStationfaceplateproperlycanresultinapotentiallyhazardouscondition.AVERTISSEMENT!Pourinstallationd’AC,défautdebrancherlamiseàlaterredelaboîtearrièreenmétaletlafaçadeavantcorrectementpeutentraînerunesituationdangereuse.3Ground WireGround WireBack Box Door Station Faceplate
©2012 Control4. All rights reserved. Control4, the Control4 logo, the Control4 iQ logo and the Control4 certified logo are registered trademarks or trademarks  of Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners.control4.com| ™4WarrantyLimited2-yearWarranty.Gotohttp://www.control4.com/warrantyfordetails.About This DocumentPartnumber:200-00244,Rev.E6/05/2012
  Regulatory Compliance & Safety Information for Contol4 Model C4-DSC-EN-INT.  Electrical Safety Advisory  Important Safety Information Read the safety instructions before using this product.  1.  Read these instructions.  2.  Keep these instructions.  3.  Heed all warnings.  4.  Follow all instructions.  5.  Do not use this apparatus near water.  6.  Clean only with dry cloth.  7.  Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.  8.  Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.  Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer.  12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time.  This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources.  The warranty for this equipment does not cover damage caused by electrical surge or lightning transients.  To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor.  14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. Use the mains plug to disconnect the apparatus from the AC mains. The mains plug shall remain readily operable.  16. To completely disconnect unit power from the AC mains, disconnect the unit’s power cord from the mains socket. To reconnect power, plug the unit’s power cord into the mains socket following all safety instructions and guidelines.  The socket-outlet shall be installed near the equipment and shall be easily accessible. 17.  This product relies on the buildings installation for short-circuit (overcurrent) protection.  Ensure that the protective device is rated not greater than: 120 VAC, 20A or 240 VAC 10A.
 18. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type.  Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines.  Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54° C or 130° F.  19. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. 20. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if placed in close proximity.   The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product  Caution: To reduce the risk of electric shock, do not remove cover (or back).  No user serviceable parts inside.  Refer servicing to qualified service personnel.  The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. See marking on bottom / back of product    Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture AVERTISSEMENT! Pour réduire le risque de choc électrique, n'exposez pas cet appareil à la pluie ou à l'humidité. WARNUNG! Um das Risiko des elektrischen Schlages zu verringern, setzen Sie diesen Apparat nicht Regen oder Feuchtigkeit aus. Save these instructions  Compliance of this equipment is confirmed by the following label that is placed on the equipment:     USA & Canada Compliance  FCC Part 15, Subpart B / ICES-003Unintentional Emissions Interference Statement  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules and Industry Canada ICES-003.  These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.  This equipment generates uses and can radiate radio frequency energy
 and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:    Reorient or relocate the receiving antenna.   Increase the separation between the equipment and receiver.   Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.   Consult the dealer or an experienced radio/TV technician for help.  This device complies with part 15 of the FCC rules and Industry Canada ICES-003. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.  IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.  IMPORTANT! Tous les changements ou modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de l’utilisateur pour actionner cet équipement.  Ferrite clamp installation. When installing a Control4® C4-DSC-EN-INT Door Station, also install the enclosed ferrite clamp as described in this document.   Install the ferrite clamp on the Ethernet cable no farther than 6 inches from the Ethernet jack inside of the back box.   Compliance of this equipment is confirmed by the following label that is placed on the equipment:     FCC Part 15, Subpart C / RSS-210 Intentional Emissions Interference Statement  Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment:  Notice: The term “FCC ID:” and “IC” before the certification number signifies that FCC and Industry Canada technical specifications were met.  FCC ID: R33C4DSCINT IC: 7848A-C4DSCINT
   This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-210, Antenna Requirements.  Do not use any antenna other than the one provided with the unit.    RF Radiation Exposure Statement  This equipment complies with the FCC/IC radiation exposure limits set fourth for portable transmitting devices operation in an uncontrolled environment.  End users must follow the specific operating instructions to satisfy RF exposure compliance.    The equipment should only be used or installed at locations where there is normally at least a 20cm separation between the antenna and all persons.   This transmitter must not be co-located or operation in conjunction with any other antenna or transmitter.   Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.   European Compliance  Conformity of the equipment with the guidelines below is attested by the application of the CE mark.     CE Declaration of Conformity  Manufacturer’s Name:  CONTROL4 CORPORATION  Manufacturer’s Address:   11734 S. ELECTION ROAD SUITE 200  SALT LAKE CITY  UT 84020 USA                          EU Representative Name:  CONTROL4 EMEA LIMITED EU Representative Address:  UNIT3, GREEN PARK BUSINESS CENTRE SULTON-ON-THE FOREST YORK YO61 IET, UNITED KINGDOM       Product Name(s):   Doorbell Station  Brand:  Contol4     Model(s): C4-DSC-EN-INT  Product Standard(s) to which Conformity of the Council Directive(s) is declared:  EMC - 2004/108/EC “Electromagnetic Compatibility (EMC) Directive”: (Emissions)  EN 55022:2010, (Immunity) EN 55024:1998, EN 301 489-1:2008, EN 301 489-17:2009, EN 61000-3-2:2004 & EN 61000-3-3:2002  Safety – 206/95/EC “Low Voltage Directive (LVD)”: EN 60950-1:2006 (2nd Edition)   .
 Telecom & Radio - 1999/5/EC Radio equipment and Telecommunications Terminal Equipment (R&TTE) Directive: EN 300 328 V1.7.1 (2006-10)  RoHS - 2002/95/EC Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (EEE) & WEEE - 2002/96/EC Waste of Electrical and Electronic Equipment (EEE).  We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards.  Date of Issue: July 24, 2012  Legal Representative  Signature     Roger Midgley    Sr. Regulatory Compliance Engineer      National Restrictions This product may be used in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Ce produit peut être utilisé dans tous les pays de l'UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans aucune limitation, excepté pour les pays mentionnés ci-dessous: Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che seguono le direttive EU 1999/5/EC) senza nessuna limitazione, eccetto per i paesii menzionati di seguito: Das Produkt kann in allen EU Staaten ohne Einschränkungen eingesetzt werden (sowie in anderen Staaten die der EU Direktive 1999/5/CE folgen) mit Außnahme der folgenden aufgeführten Staaten: France In case the product is used outdoors, the output power is restricted in some parts of the band. See Table 1 below or check http://www.arcep.fr/ for more details. Dans la cas d'une utilisation en extérieur, la puissance de sortie est limitée pour certaines parties de la bande. Voir la table ci-dessous ou visitez http://www.arcep.fr/ pour de plus amples details Table 1 Applicable Power Levels in France Location  Frequency Range (MHz)  Power (EIRP) Indoor (No restrictions)  2400-2483.5  100 mW (20 dBm) Outdoor  2400-2454 2454-2483.5  100 mW (20 dBm) 10 mW (10 dBm)
  Recycling  Control4 understands that a commitment to the environment is essential for a health life and sustainable growth for future generations.  We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment.  This commitment is represented by combining technological innovation with sound environmental business decisions.  WEEE Compliance  Control4 is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2002/96/EC).  The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be appropriately disposed of or recycled at the end of their product lifespan.  For collection or recycling of Control4 products, please contact your local Control4 representative or dealer.   Australia / New Zealand Compliance  Compliance of this equipment is confirmed by the following label that is placed on the equipment:      About this Document  Copyright © 2012 Control4 Corporation.  All rights reserved.  Control4 and the Control4 logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries.   Part Number 200-00319 Rev A, 7/24/2012

Navigation menu