Control4 C4EA5V2 System controller User Manual Control4 EA 5 V2 Installation Guide

Control4 System controller Control4 EA 5 V2 Installation Guide

User Manual

Control4 EA-5 ControllerInstallation GuideSupported model• C4-EA5 Entertainment and Automation Controller, 5 Zone• C4-EA5-V2 Entertainment and Automation Controller, 5 Zone, V2IntroductionThe Control4 EA-5 Entertainment and Automation Controller is designed to deliver the ultimate smart home experience, featuring the highest-quality audio of the EA series and processing power to coordinate hundreds of smart devices. The EA-5 can automate sophisticated home theaters, complex interior and exterior lighting scenes, vital security and communications systems, and climate controls for multiple zones. The EA-5 features five independent audio outputs—two digital coaxial, two RCA stereo analog, and one HDMI—with an audiophile-grade signal-to-noise ratio of 118dB. A built-in music server delivers immersive, multi-stream, high-resolution audio with five built-in simultaneous audio streams from your local music collection, a variety of streaming music services, or from AirPlay-enabled devices using native Control4 ShairBridge technology. Expand beyond five streams by including additional EA-5 or EA-3 Controllers. Secure, wireless ZigBee communication; plentiful I/O including IR, serial, contacts and relays; and IP control enable connections to smart home devices such as thermostats, door locks, doorbells, cameras, security panels, sensors, lighting, shades, garage door controllers, irrigation systems, and much more. The sleek design, rack-mount form factor, and top-of-the-line connectivity make the EA-5 the ultimate foundation for any Control4 system and the platform to power the future of your smart home.Box contentsThe following items are included in the box:• EA-5 controller• AC power cord• IR emitters (8)• Rack ears (2, pre-installed on the EA-5 V2)• Rubber feet (2, pre-installed on the EA-5 V1)• External antennas (3 with EA-5 V1, 1 with EA-5 V2)• Terminal blocks for contacts and relaysAccessories sold separately• Control4 3.5 mm-to-DB9 Serial Cable (C4-CBL3.5-DB9B)• Dual-Band WiFi USB Adapter for EA-5 V2 (C4-USBWIFI or C4-USBWIFI-1)WarningsCaution! To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture.Avertissement ! Pour réduire le risque de choc électrique, n’exposez pas cet appareil à la pluie ou à l’humidité.Caution! In an over-current condition on USB or contact output the software disables the output. If the attached USB device or contact sensor does not appear to power on, remove the device from the controller.Avertissement ! Dans une condition de surintensité sur USB ou sortie de contact le logiciel désactive sortie. Si le périphérique USB ou le capteur de contact connecté ne semble pas s’allumer, retirez le périphérique du contrôleur.Requirements and specificationsNote: We recommend using Ethernet instead of WiFi for the best network connectivity. Note: The Ethernet or WiFi network should be installed before you install the EA-5 controller. Note: The EA-5 V2 requires OS 2.10.2 or higher. The EA-5 V1 requires OS 2.8.1 or higher.Composer Pro is required to configure this device. See the Composer Pro User Guide (ctrl4.co/cpro-ug) for details.SpecificationsInputs / Outputs Video out 1 video out—1 HDMIVideo HDMI 1.4 output; HD 1080p, 50-60 HzAudio out 5 audio out—1 HDMI, 2 stereo analog, 2 digital coaxAudio playback formats AAC, AIFF, ALAC, FLAC, M4A, MP2, MP3, MP4/M4A, Ogg Vorbis, PCM, WAV, WMAHigh-res audio playback Up to 192 kHz / 24 bitAudio in 4 audio in—2 stereo analog, 2 digital coaxAudio delay on audio in Up to 3.5 seconds, depending on network conditionsAdvanced audio subsystem Dual audio signal processors, multiple sample rate convertersAudio system controls (analog or digital coax)10-band graphic equalizer, input gain, output gain, loudness, tone controls, balanceSignal-to-noise ratio <-118 dBFSTotal harmonic distortion 0.00023 (-110 dB)NetworkEthernet 10/100/1000BaseT compatible (required for controller setup). Built-in Ethernet switch 1 Ethernet in + 4 gigabit Ethernet switch portsWiFi Internal Dual-Band Wireless-N (EA-5 V1) (2.4GHz, 5GHz, 802.11n/g/b) (EA-5 V1)Optional Dual-Band WiFi USB Adapter (EA-5 V2) (2.4 GHz, 5 Ghz, 802.11ac/b/g/n/a)WiFi security WPA/WPA2WiFi antenna 2 external reverse SMA connectors (EA-5 V1)ZigBee Pro 802.15.4ZigBee antenna External reverse SMA connectoreSATA port 1 eSATA portUSB port 1 USB 2.0 port—500mAControlIR OUT 8 IR out—5V 27mA max output1 IR blaster—frontIR capture 1 IR receiver—front; 20-60 KHzSERIAL OUT 4 Serial out—2 DB9 ports and 2 shared with IR out 1-2Contact 4 contact sensors—2V-30VDC input, 12VDC 0.5A maximum outputRelay 4 relays—AC: 36V, 2A maximum voltage across relay; DC: 24V, 2A maximum voltage across relay PowerPower requirements 100-240 VAC, 60/50HzPower consumption Max: 40W, 136 BTUs/hourIdle: 15W, 51 BTUs/hourOtherOperating temperature 32˚F ~ 104˚F (0˚C ~ 40˚C)Storage temperature 4˚F ~ 158˚F (-20˚C ~ 70˚C)Fan dB level Max: 35 dBDimensions (H × W × D) 17.5 × 10.125 × 1.875" w/feet (444 × 258 × 49 mm)Weight 6.85 lbs (3.10 kg)Shipping weight 9.30 lbs (4.20 kg)Additional resourcesThe following resources are available for more support.• Control4 Knowledgebase: kb.control4.com and Dealer Forums: forums.control4.com• Control4 Technical Support• Control4 website: www.control4.com• Composer Pro documentation in online help or PDF format available on the Dealer Portal under Support: ctrl4.co/docsFront viewA Data LED—The LED indicates that the controller is streaming audio.B IR window—IR blaster and IR receiver for learning IR codes.C Caution LED—This LED shows solid red, then blinks blue during the boot process. Note: The Caution LED flashes orange during the factory restore process. See “Reset to factory settings” in this document.D Link LED—The blue LED indicates that the controller has been identified in a Control4 Composer project and is communicating with Director.E Power LED—The blue LED indicates that AC power is connected. The controller turns on immediately after power is applied to it.Back viewA Power plug port—AC power receptacle for an IEC 60320-C13 power cord.B WIFI 1—Antenna 1 for the WiFi radio (EA-5 V1 only).C Contact/Relay port—Connect up to four relay devices and four contact sensor devices to the terminal block connector. Relay connections are COM, NC (normally closed), and NO (normally open). Contact sensor connections are +12, SIG (signal), and GND (ground).D GIGABIT SWITCH—Four-port gigabit ethernet switch to connect other local devices to the network.E ETHERNET IN—RJ-45 jack for a 10/100/1000 BaseT Ethernet connection.F USB—One port for an external USB drive or, on an EA-5 V2, the optional Dual-Band WiFi USB Adapter. See “Set up external storage devices” in this document. G E-SATA—One port for an external eSATA drive. See “Setting up external storage devices” in this document.H WIFI 2—Antenna 2 for the WiFi radio (EA-5 V1 only)I SERIAL—Two serial ports for RS-232 control. See “Connecting the serial ports” in this document.J ID and FACTORY RESET—ID button to identify the device in Composer Pro. The ID button on the EA-5 V2 is also an LED that displays feedback useful during a factory restore. FACTORY RESET button is used to restore the controller to factory defaults. Can also reboot the controller. K HDMI OUT—An HDMI port to display system menus. Also an audio out over HDMI.L IR / SERIAL—Eight 3.5 mm jacks for up to eight IR emitters or for a combination of IR emitters and serial devices. Ports 1 and 2 can be configured independently for serial control or for IR control. See “Setting up IR emitters” in this document for more information.M DIGITAL AUDIO—Two digital coax audio input and two output ports. Allows audio to be shared (IN 1 or 2) over the local network to other Control4 devices. Outputs audio (OUT 1 or 2) shared from other Control4 devices or from digital audio sources (local media or digital streaming services such as TuneIn.)N ANALOG AUDIO—Two stereo audio input and two output ports. Allows audio to be shared (IN 1 or 2) over the local network to other Control4 devices. Outputs audio (OUT 1 or 2) shared from other Control4 devices or from digital audio sources (local media or digital streaming services such as TuneIn.)O ZIGBEE—Antenna for the ZigBee radio. AC POWER:100-240 V~60/50 Hz, 0.5 AWIFI 1 WIFI 2SERIAL 2USB E-SATAFACTORYRESETOUTCOMNCNOCOMNCNOCOMNCNOCOMNCNO+12SIGGND+12SIGGND+12SIGGND+12SIGGND357ZIGBEESERIAL 1ID468 IN 1 IN 2 OUT 1 OUT 21 2 3 4 1/ 3 IN 1 OUT 1IN 2 OUT 2DIGITAL AUDIO ANALOG AUDIOGIGABIT SWITCHETHERNET INIR / SERIAL2/ 4A B C D E AC POWER:100-240 V~60/50 Hz, 0.5 AWIFI 1 WIFI 2SERIAL 2USB E-SATAFACTORYRESETOUTCOMNCNOCOMNCNOCOMNCNOCOMNCNO+12SIGGND+12SIGGND+12SIGGND+12SIGGND357ZIGBEESERIAL 1ID468 IN 1 IN 2 OUT 1 OUT 21 2 3 4 1/ 3 IN 1 OUT 1IN 2 OUT 2DIGITAL AUDIO ANALOG AUDIOGIGABIT SWITCHETHERNET INIR / SERIAL2/ 4A B C D E F G H I J K L MN OInstalling the controllerTo install the controller:1 Ensure that the home network is in place before starting system setup. The controller requires a network connection, Ethernet (recommended) or WiFi, to use all of the features as designed. When connected, the controller can access web-based media databases, communicate with other IP devices in the home, and access Control4 system updates.2 Mount the controller in a rack or stacked on a shelf. Always allow plenty of ventilation. See “Mounting the controller in a rack” in this document. 3 Connect the controller to the network.• Ethernet—To connect using an Ethernet connection, plug the data cable from the home network connection into the controller’s RJ-45 port (labeled “ETHERNET IN”) and the network port on the wall or at the network switch. • WiFi—To connect using WiFi, first connect the controller to Ethernet, and then use Composer Pro System Manager to reconfigure the controller for WiFi. Important: Do not install your EA controller on a 172.18.xxx.xxx subnet.4 Connect system devices. Attach IR and serial devices as described in “Connecting the IR ports/serial ports” and “Setting up IR emitters.”5 Set up any external storage devices as described in “Setting up external storage devices” in this document.6 Power up the controller. Plug the power cord into the controller’s power plug port and then into an electrical outlet. Mounting the controller in a rackUsing the pre-installed rack-mount ears, the EA-5 can easily be mounted in a rack for convenient installation and flexible rack placement. The pre-installed rack-mount ears can even be reversed to mount the controller facing the rear of the rack, if needed.To attach the rubber feet to the controller:1 Remove the two screws in each of the rack ears on the bottom of the controller. Remove the rack ears from the controller.2 Remove the two additional screws from the controller case and place the rubber feet on the controller. .3 Secure the rubber feet to the controller with three screws in each rubber foot.Pluggable terminal block connectorsFor the contact and relay ports, the EA-5 makes use of pluggable terminal block connectors which are removable plastic parts that locks in individual wires (included).To connect a device to the pluggable terminal block:1 Insert one of the wires required for your device into the appropriate opening in the pluggable terminal block you reserved for that device.2 Use a small flat-blade screwdriver to tighten the screw and secure the wire in the terminal block.Example: To add a motion sensor (see Figure 3), connect its wires to the following contact openings:• Power input to +12V• Output signal to SIG• Ground connector to GNDNote: To connect dry contact closure devices, such as doorbells, connect the switch between +12 (power) and SIG (signal).
control4.com | 888.400.4070 Connecting the contact portsThe EA-5 provides four contact ports on the included pluggable terminal blocks. See the examples below to learn how to connect devices to the contact ports.Wire the contact to a sensor that also needs power (Motion sensor)Wire the contact to a dry contact sensor (Door contact sensor)Wire the contact to an externally powered sensor (Driveway sensor)Connecting the relay portsThe EA-5 provides four relay ports on the included pluggable terminal blocks. See the examples below to learn now to connect various devices to the relay ports. Wire the relay to a single-relay device, normally open (Fireplace)Wire the relay to a dual-relay device (Blinds)Wire the relay with power from the contact, normally closed (Amplifier trigger)Motion Sensor+12V 0V COM NODry ContactDrivewaySensorExternal12V PowerFireplaceDual-Relay BlindUP COM DOWNRelay 1 Relay 212V TriggerConnecting the serial portsThe EA-5 controller provides four serial ports. SERIAL 1 and SERIAL 2 can connect to a standard DB9 serial cable. IR ports 1 and 2 (serial 3 and 4) can be reconfigured independently for serial communication. If not used for serial, they can be used for IR. Connect a serial device to the controller using the Control4 3.5 mm-to-DB9 Serial Cable (C4-CBL3.5-DB9B, sold separately). 1 The serial ports support many dierent baud rates (acceptable range: 1200 to 115200 baud for odd and even parity). Serial ports 3 and 4 (IR 1 and 2) do not support hardware flow control.2 See Knowledgebase article #268 (dealer.control4.com/dealer/knowledgebase/article/268) for pinout diagrams.3 To configure a port’s serial settings, make the appropriate connections in your project using Composer Pro. Connecting the port to the driver will apply the serial settings contained in the driver file to the serial port. See the Composer Pro User Guide for details.Note: Serial ports 3 and 4 can be configured as straight-through or null with Composer Pro. Serial ports by default are configured straight-through and can be changed in Composer by selecting the option Enable Null-Modem Serial Port (3/4).Setting up IR emittersThe EA-5 controller provides 8 IR ports. Your system may contain third-party products that are controlled through IR commands. The included IR emitters can send commands from the controller to any IR-controlled device.1 Connect one of the included IR emitters into an IR OUT port on the controller.2 Remove the adhesive backing from the emitter (round) end of the IR emitter and ax it to the device to be controlled over the IR receiver on the device.Setting up external storage devicesYou can store and access media from an external storage device, for example, a USB drive or eSATA drive, by connecting the USB drive to the USB port and configuring or scanning the media in Composer Pro. A NAS drive can also be used as an external storage device; see the Composer Pro User Guide (ctrl4.co/cpro-ug) for more details.Note: We support only externally powered USB drives or solid-state USB drives (USB thumb drives). USB hard drives that do not have a separate power supply are not supported. Note: When using USB or eSATA storage devices on an EA-5 controller, a single primary partition formatted FAT32 is recommended. Composer Pro driver informationUse Auto Discovery and SDDP to add the driver to the Composer project. See the Composer Pro User Guide (ctrl4.co/cpro-ug) for details.TroubleshootingReset to factory settingsCaution! The factory restore process will remove the Composer project. Back up the project with Composer Pro before you start the factory restore process To restore the controller to the factory default image:1 Insert a straightened paper clip into the small hole on the back of the controller labeled FACTORY RESTORE.2 Press and continue to hold the FACTORY RESTORE button, the controller resets and the caution LED turns solid red.3 Hold the button until the Caution LED flashes double orange. This should take five to seven seconds. The Caution LED flashes orange while the factory restore is running. When complete, the Caution LED turns o and the device power cycles one more time to complete the factory restore process.Note: On an EA-5 V2 controller, the ID button is also an LED that provides the same feedback as the Caution LED on the front of the controller.Power cycle the controller1 Press and hold the ID button for five seconds. The controller turns o and back on.Reset the network settingsTo reset the controller network settings to the default: 1 Disconnect power to the controller.2 While pressing and holding the ID button on the back of the controller, reconnect power to the controller.3 Hold the ID button until the Caution LED (rear ID LED) appears solid orange and the Link and Power LEDs are solid blue, and then immediately release the button.Note: In OS 2.10.1 and lower, the Caution LED appears solid blue during the network reset check. After updating to OS 2.10.2 and higher, the Caution LED appears orange during the network reset check.LED status information Just powered on Bootloader loaded Kernel loaded Network reset check Factory restore underway Factory restore fail Connected to Director Playing audioRegulatory/Safety informationTo review regulatory information for your Control4 products, see the information located on the Control4 website at ctrl4.co/reg.WarrantyVisit ctrl4.co/warranty for details.More helpFor the latest version of this document and to view additional materials, open the URL below or scan the QR code on a device that can view PDFs.—Flashing LED —Solid LEDon EA-5 V2 onlyMOST RECENT VERSIONctrl4.co/ea5-igMORE INFO ON EA CONTROLLERSctrl4.co/ea200-00382-B 2018-05-09 DHCopyright ©2018, Control4 Corporation. All rights reserved. Control4, the Control4 logo, the 4-ball logo, 4Sight, Control4 My Home, and Mockupancy are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice. BData Caution Link Power
Regulatory Compliance & Safety Information for Control4 Model C4-EA5-V2 Electrical Safety Advisory Sécurité électrique consultatif Important Safety Information Informations de sécurité importantes Read the safety instructions before using this product. Lisez les consignes de sécurité avant d'utiliser ce produit. 1. Read these instructions. 1. Lisez ces instructions. 2. Keep these instructions. 2. Conservez ces instructions. 3. Heed all warnings. 3. Respectez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les instructions. 5. Do not use this apparatus near water. 5. Ne pas utiliser cet appareil près de l'eau. 6. Clean only with dry cloth. 6. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 7. Ne pas bloquer les ouvertures de ventilation. Installer conformément aux instructions du fabricant. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 8. Ne pas installer près de sources de chaleur telles que des radiateurs, registres de chaleur, poêles, ou autres appareils (incluant les amplificateurs) qui produisent de la chaleur. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 9. Ne pas contourner le dispositif de sécurité de la fiche polarisée ou de mise à la terre. Une fiche polarisée possède deux lames dont une plus large que l'autre. Une fiche de terre a deux lames et une troisième broche de terre. La lame large ou la troisième broche est fournie pour votre sécurité. Si la fiche fournie ne s'adapte pas à votre prise, consultez un électricien pour le remplacement de la prise obsolète.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 10. Protégez le cordon d'alimentation ne soit piétiné ou pincé, en particulier au niveau des fiches, des prises et au point où il sort de l'appareil. 11. Only use attachments/accessories specified by the manufacturer. 11. Utilisez uniquement des fixations / accessoires spécifiés par le fabricant. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 12. Utilisez uniquement avec le chariot, le socle, le trépied, le support ou la table spécifiés par le fabricant ou vendu avec l'appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous déplacez l'ensemble chariot / appareil pour éviter des blessures dues au renversement. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 13. Débranchez cet appareil pendant les orages ou lorsqu'il n'est pas utilisé pendant de longues périodes de temps. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 14. Confiez toutes les réparations à un personnel qualifié. Une réparation est nécessaire lorsque l'appareil a été endommagé de quelque façon que ce soit le cordon d'alimentation ou la fiche est endommagé, du liquide a été renversé ou si des objets sont tombés dans l'appareil, l'appareil a été exposé à la pluie ou à l'humidité, ne fonctionne pas normalement , ou s'il est tombé. 15. This equipment uses AC power which can be subjected to electrical surges, typically lightning transients which are very destructive to customer terminal equipment connected to AC power sources. The warranty for this equipment does not cover damage caused by electrical surge or lightning transients. To reduce the risk of this equipment becoming damaged it is suggested that the customer consider installing a surge arrestor. 15. Cet équipement utilise la puissance AC qui peuvent être soumis à des surtensions électriques, la foudre généralement transitoires qui sont très destructives envers les équipements terminaux connectés à des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causés par les surtensions électriques ou transitoires de foudre. Pour réduire le risque de cet équipement devient endommagé, il est suggéré que le client envisager l'installation d'un limiteur de surtension. 16. To completely disconnect unit power from the AC mains, remove the power cord from the appliance coupler and/or turn off the circuit breaker. To reconnect power, turn on the circuit breaker following all safety instructions and guidelines. The circuit breaker shall remain readily accessible. 16. Pour débrancher complètement l'alimentation secteur du réseau secteur, retirez le cordon d'alimentation du coupleur de l'appareil et / ou éteignez le disjoncteur. Pour reconnecter l'alimentation, allumez le disjoncteur en suivant toutes les consignes et consignes de sécurité. Le disjoncteur doit être facilement accessible.
17. This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. 17. Ce produit repose sur l'installation des bâtiments pour les courts-circuits (surintensité) de protection. Assurez-vous que le dispositif de protection est assignée ne dépassant pas: 20A. 18. CAUTION: As with all batteries, there is a risk of explosion or personal injury if the battery is replaced by an incorrect type. Dispose of used battery according to the instructions of the battery manufacturer and applicable environmental guidelines. Do not open, puncture or incinerate the battery, or expose it to conducting materials, moisture, liquid, fire or heat above 54° C or 130° F. 18. ATTENTION: Comme avec toutes les batteries, il ya un risque d'explosion ou de blessure si la batterie est remplacée par un type incorrect. Éliminez les batteries usagées selon les instructions du fabricant de la batterie et applicables des directives environnementales. Ne pas ouvrir, percer ou incinérer la batterie, ou de l'exposer à des matériaux conducteurs, de l'humidité, du liquide, un incendie ou une température supérieure à 54 ° C ou 130 ° F. 19. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. 19. N'introduisez jamais d'objets d'aucune sorte dans ce produit à travers les fentes du boîtier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pièces qui pourraient entraîner un incendie ou un choc électrique. 20. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if placed in close proximity. 20. Ce produit peut interférer avec des appareils électriques tels que les magnétophones, téléviseurs, radios, ordinateurs et fours à micro-ondes si placés à proximité. The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product L'éclair et la flèche dans le triangle est un signe d'alerte pour vous avertir d'une tension dangereuse à l'intérieur du produit Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. Attention: Pour réduire le risque de choc électrique, ne pas retirer le couvercle (ou l'arrière). Aucune pièce réparable par l'utilisateur. Confiez l'entretien à un personnel qualifié. The exclamation point within the triangle is a warning sign alerting you of important instructions accompanying the product. Le point d'exclamation dans un triangle est un signe d'avertissement vous signale des instructions importantes accompagnant le produit. See marking on bottom / back of product Voir le marquage sur les bas / dos du produit Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture AVERTISSEMENT! Pour réduire le risque de choc électrique, n'exposez pas cet appareil à la pluie ou à l'humidité.
Save these instructions Conservez ces instructions Compliance of this equipment is confirmed by the following label that is placed on the equipment: Conformité de cet appareil est confirmé par le symbole suivant qui est placé sur l'équipement: USA & Canada Compliance FCC Part 15, Subpart B Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Partie 15, sous-section B Unintentional Déclaration sur les interférences des émissions Cet équipement a été testé et jugé conforme aux limites établies pour un dispositif numérique de classe B, conformément à la Partie 15 des règlements de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles lorsque l'équipement est utilisé dans une installation résidentielle. Cet équipement génère, utilise et peut émettre de l'énergie rayonnent fréquence et, s'il n'est pas installé et utilisé conformément aux instructions, il peut causer des interférences nuisibles aux communications radio. Cependant, il n'existe aucune garantie que des interférences ne se produiront pas dans une installation particulière. Si cet équipement provoque des interférences nuisibles à la réception radio ou télévision, ce qui peut être déterminé en mettant l'équipement hors et sous tension, l'utilisateur est encouragé à essayer de corriger l'interférence par une ou plusieurs des mesures suivantes: • Réorienter ou déplacer l'antenne de réception. • Augmenter la distance entre l'équipement et le récepteur.
• Connecter l'équipement à une prise sur un circuit différent de celui sur lequel le récepteur est branché. • Consulter le revendeur ou un technicien radio / télévision qualifié pour obtenir de l'aide. This device complies with part 15 of the FCC rules and Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3(B)/NMB-3(B) Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. CAN ICES-3(B)/NMB-3(B) IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de l’utilisateur pour actionner cet équipement. FCC Part 15, Subpart C / RSS-247 Intentional Emissions Interference Statement Compliance of this equipment is confirmed by the following certification numbers that are placed on the equipment: Notice: The term “FCC ID:” and “IC:” before the certification number signifies that FCC and Industry Canada technical specifications were met. C4-EA5-V2: FCC ID: R33C4EA5V2 IC: 7848A-C4EA5V2 This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-247, Antenna Requirements. Do not use any antenna other than the one provided with the unit. FCC Partie 15, sous-partie C / RSS-247 Déclaration volontaire des émissions interférences Conformité de cet appareil est confirmé par les chiffres de certification suivants qui sont placés sur l'équipement: Avis: Le terme «FCC ID:" et "IC:" devant le numéro de certification signifie que les spécifications techniques de la FCC et d'Industrie Canada ont été respectées. C4-EA5-V2: FCC ID: R33C4EA5V2 IC: 7848A-C4EA5V2 Cet équipement doit être installé par des professionnels qualifiés ou entrepreneurs conformément aux normes FCC partie 15.203 & IC RSS-247, Exigences d'antenne. Ne pas utiliser une antenne autre que celui fourni avec l'appareil.
This radio transmitter has been approved by Industry Canada to operate with the antenna type listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Manufacturer: SHEN ZHEN COS-LINK TECHNOLOGY CO., LTD Model: CSL-AN2400-100840-B01 Maximum Gain: 2.4 GHz (2 dBi) Cet émetteur radio a été approuvé par Industrie Canada pour fonctionner avec le type d'antenne indiqué ci-dessous avec le gain maximal admissible indiqué. Les types d'antennes non inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type, sont strictement interdits pour une utilisation avec cet appareil. Manufacturer: SHEN ZHEN COS-LINK TECHNOLOGY CO., LTD Model: CSL-AN2400-100840-B01 Maximum Gain: 2.4 GHz (2 dBi) RF Radiation Exposure Statement This equipment complies with the FCC/IC radiation exposure limits set fourth for portable transmitting devices operation in an uncontrolled environment. End users must follow the specific operating instructions to satisfy RF exposure compliance. • The equipment should only be used or installed at locations where there is normally greater than a 20cm separation between the antenna and all persons. • This transmitter must not be co-located or operation in conjunction with any other antenna or transmitter. • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Déclaration d'exposition aux radiations RF Cet équipement est conforme aux limites FCC / IC d'exposition aux rayonnements définies quatrième opération appareils portables transmettre dans un environnement non contrôlé. Les utilisateurs finaux doivent suivre les instructions de fonctionnement spécifiques pour satisfaire la conformité aux expositions RF. • L'équipement ne doit être utilisé ou installé à des endroits où il est normalement supérieure à une séparation de 20 cm entre l'antenne et toute personne. • Cet émetteur ne doit pas être co-localisés ou fonctionnement en conjonction avec une autre antenne ou un autre émetteur. • Tout changement ou modification non expressément approuvé par la partie responsable de la conformité pourraient annuler l'autorité de l'utilisateur à utiliser cet équipement. Europe Compliance Compliance of this equipment is confirmed by the following logo that is placed on the product ID label that is placed on the bottom of the equipment. The full text of the EU Declaration of Conformity (DoC) is available on the following pages:
Recycling Control4 understands that a commitment to the environment is essential for a health life and sustainable growth for future generations. We are committed to supporting the environmental standards, laws, and directives that have been put in place by various communities and countries that deal with concerns for the environment. This commitment is represented by combining technological innovation with sound environmental business decisions. WEEE Compliance Control4 is committed to meeting all requirements of the Waste Electrical and Electronic Equipment (WEEE) directive (2002/96/EC). The WEEE directive requires the manufacturers of electrical and electronic equipment who sell in EU countries: (1) label their equipment to notify customers that it needs to be recycled, and (2) provide a way for their products to be appropriately disposed of or recycled at the end of their product lifespan. For collection or recycling of Control4 products, please contact your local Control4 representative or dealer. About this Document Copyright © 2018 Control4 Corporation. All rights reserved. Control4 and the Control4 logo are registered trademarks or trademarks of Control4 Corporation in the United States and/or other countries. Part Number 200-00XXX Rev A, 7/31/2018
European Compliance (English) Conformity of the equipment with the guidelines below is attested by the application of the CE mark. CE Declaration of Conformity Manufacturer’s Name: CONTROL4 CORPORATION Manufacturer’s Address: 11734 S. ELECTION ROAD SUITE 200 SALT LAKE CITY UT 84020 USA EU Representative Name: CONTROL4 EMEA LIMITED EU Representative Address: UNIT3, GREEN PARK BUSINESS CENTRE SULTON-ON-THE FOREST YORK YO61 IET, UNITED KINGDOM Product Name(s): Home Controller Brand: Control4 Model(s): C4-EA5-V2 Product Standard(s) to which Conformity of the Council Directive(s) is declared: EMC - 2014/30/EU “Electromagnetic Compatibility (EMC) Directive”: (Emissions) EN 55032:2015 (Immunity) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Safety – 2014/35/EC “Low Voltage Directive (LVD)”: EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Radio - 2014/53/EU Radio Equipment Directive (RED): EN 300 328 V2.1.1 ErP - 2009/125/EC Energy-related Product Directive. RoHS - 2011/65/EU Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (EEE) & WEEE - 2002/96/EC Waste of Electrical and Electronic Equipment (EEE). We, the undersigned, hereby declare that the equipment specified above conforms to the above directives and standards. Date of Issue: July 31, 2018. Legal Representative Signature Roger Midgley Sr. Regulatory Compliance Engineer
Conformité européenne (French) Conformité de l'équipement avec les directives ci-dessous est attestée par l'apposition de la marque CE. Déclaration de conformité CE Le nom du fabricant: CONTROL4 CORPORATION Le fabricant Adresse: 11734 S. ÉLECTION Road Suite 200 SALT LAKE CITY UT 84020 USA Nom Représentant de l'UE: CONTROL4 EMEA LIMITED UE représentant Adresse: Unit3, GREEN PARK CENTRE D'AFFAIRES Sulton-ON-THE FOREST YORK YO61 IET, ROYAUME-UNI Nom (s) de produit: Accueil Controller Marque: Control4 Modèle (s): C4-EA5-V2 Produit standard (s) dont la conformité de la directive du Conseil (s) est déclarée: EMC - 2014/30/EU "compatibilité électromagnétique (CEM)" UE: (Émissions) EN 55032:2015 (immunité) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Sécurité - 2014/35/EC "Directive Basse Tension (DBT)": EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Radio - 2014/53/EU directive équipement radio (RED): EN 300 328 V2.1.1 ErP - 2009/125/EC liées à l'énergie directive sur les produits. RoHS - 2011/65/EU limitation de l'utilisation de certaines substances dangereuses dans les équipements électriques et électroniques (EEE) et DEEE - 2002/96/EC Déchets d'équipements électriques et électroniques (EEE). Nous, soussignés, déclarons que l'équipement indiqué ci-dessus est conforme aux directives et normes ci-dessus. Date de publication 31 juillet 2018. Représentant légal Signature Roger Midgley Ingénieur de conformité réglementaire Sr.
European Compliance (German) Die Konformität mit den folgenden Richtlinien wird durch die Anwendung des CE-Kennzeichen bestätigt. CE-Konformitätserklärung Name des Herstellers: Control4 CORPORATION Adresse des Herstellers: 11734 S. WAHL ROAD SUITE 200 SALT LAKE CITY UT 84020 USA EU-Vertreter Name: Control4 EMEA LIMITED EU-Vertreter Adresse: Unit3, GREEN Park Geschäftszentrum Sulton-ON-THE FOREST YORK YO61 IET, VEREINIGTES KÖNIGREICH Produkt-Name (n): Home Controller Marke: Control4 Modell (e): C4-EA5-V2 Produkt-Norm (en), um die Konformität der Richtlinie (n) deklariert ist: EMC - 2014/30/EU "Elektromagnetische Verträglichkeit (EMV) Die Richtlinie": (Emissionen) EN 55032:2015 (Immunität) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Sicherheit - 2014/35/EC "Niederspannungsrichtlinie (LVD)": EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Radio - 2014/53/EU über Funkanlagen-Richtlinie (RED): EN 300 328 V2.1.1 ErP - 2009/125/EC Energiebezogene Produktrichtlinie. RoHS - 2011/65/EU zur Beschränkung der Verwendung bestimmter gefährlicher Stoffe in Elektro- und Elektronikgeräten (EEE) & WEEE - 2002/96/EC Richtlinie über Elektro- und Elektronikgeräten (EEE). Wir, die Unterzeichneten, erklären hiermit, dass das oben angegebene Gerät zu den oben genannten Richtlinien und Normen. Ausstellungsdatum: 31. Juli 2018 Gesetzlicher Vertreter Stempel, Unterschrift Roger Midgley Sr. Regulatory Compliance-Ingenieur
Conformità Europea (Italian) Conformità del materiale con le linee guida qui sotto è attestata dall'applicazione del marchio CE. Dichiarazione di conformità CE Nome del produttore: Control4 CORPORATION Indirizzo del produttore: 11734 S. ELEZIONI STRADA SUITE 200 SALT LAKE CITY UT 84020 Stati Uniti d'America UE Nome Rappresentante: Control4 EMEA LIMITED UE Indirizzo Rappresentante: Unit3, GREEN PARK BUSINESS CENTRE Sulton-ON-THE FOREST YORK YO61 IET, REGNO UNITO Nome del prodotto (s): Casa controller Marca: Control4 Modello (s): C4-EA5-V2 Prodotto standard (s) a cui conformità della direttiva del Consiglio (s) è dichiarato: EMC - 2014/30/EU "Compatibilità elettromagnetica (EMC)": (Emissioni) EN 55032:2015 (immunità) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Sicurezza - 2014/35/EC "Direttiva bassa tensione (LVD)": EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Radio - 2014/53/EU Direttiva sulle apparecchiature radio dell'UE (RED): EN 300 328 V2.1.1 ErP - 2009/125/EC Energy legati direttiva sui prodotti. RoHS - 2011/65/EU Limitazione / UE dell'uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche (AEE) e RAEE - 2002/96/EC sui rifiuti di apparecchiature elettriche ed elettroniche (AEE). I sottoscritti, dichiariamo che l'apparecchiatura specificata in precedenza è conforme alle direttive e norme di cui sopra. Data di pubblicazione: 31 luglio 2018 Rappresentante legale Firma Roger Midgley Suor Conformità alle normative Ingegnere
Conformidad Europea (Spanish) La conformidad de los equipos con las siguientes pautas es atestiguado por la aplicación de la marca CE. Declaración de conformidad CE Nombre del fabricante: Control4 CORPORACIÓN Dirección del fabricante: 11734 S. ELECCIÓN Road Suite 200 SALT LAKE CITY UT 84020 EE.UU. UE Nombre Representante: Control4 EMEA LIMITED Dirección Representante de la UE: Tema 3., VERDE PARQUE EMPRESARIAL CENTRO Sulton-EN-EL BOSQUE YORK YO61 IET, REINO UNIDO Nombre (s) del producto: Controlador Inicio Marca: Control4 Modelo (s): C4-EA5-V2 Producto estándar (s) a la que la conformidad de la Directiva del Consejo (s) se declara: EMC - 2014/30/EU "Directiva de compatibilidad electromagnética (EMC)": (Emisiones) EN 55032:2015 (inmunidad) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Seguridad - 2014/35/EC "Directiva de Baja Tensión (LVD)": EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Radio - 2014/53/EU Directiva de Equipos de Radio de la UE (RED): EN 300 328 V2.1.1 ErP - 2009/125/EC relacionados con energía / CE Directiva del producto. RoHS - 2011/65/EU restricción del uso de ciertas sustancias peligrosas en equipos electrónicos (AEE) y WEEE eléctricos y / UE - 2002/96/EC de Residuos de Aparatos Eléctricos (AEE) y electrónicos. Nosotros, los abajo firmantes, declaramos por la presente que el equipo anteriormente mencionado se ajusta a las directrices y estándares anteriores. Fecha de emisión: 31 de julio de 2018 Representante legal Firma Roger Midgley Ingeniero Sr. Cumplimiento de la normativa
Conformidade Europeia (Portuguese) Conformidade do equipamento com as diretrizes abaixo é atestada pela aplicação da marca CE. Declaração de Conformidade CE Nome do fabricante: Control4 CORPORATION Do fabricante Endereço: 11734 S. ELEIÇÃO ROAD SUITE 200 SALT LAKE CITY UT 84020 EUA Representante da UE Nome: Control4 EMEA LIMITED Representante da UE Endereço: UNIT3, GREEN PARK CENTRO DE NEGÓCIO Sulton-ON-THE FOREST YO61 IET YORK, REINO UNIDO Nome (s) produto: Início Controlador Marca: Control4 Modelo (s): C4-EA5-V2 Padrão do produto (s) a que Conformidade da Directiva do Conselho (s) é declarado: EMC - 2014/30/EU "Compatibilidade Electromagnética (EMC)": (Emissões) EN 55032:2015 (Imunidade) EN 55024:2010+A1:2015, EN 301 489-1 V1.9.2 (2011-09), EN 301 489-17 V2.2.1 (2012-09), EN 61000-3-2:2014 & EN 61000-3-3:2013 Segurança - 2014/35/EC "Directiva de Baixa Tensão (LVD)": EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011 + A2:2013 Rádio - 2014/53/EU Directiva equipamento de rádio (RED): EN 300 328 V2.1.1 ERP - 2009/125/EC relacionados Energy-/ CE Directiva do produto. RoHS - 2011/65/EU Restrição do Uso de Certas Substâncias Perigosas em Equipamentos Eléctricos e Electrónicos (EEE) e WEEE - 2002/96/EC de Resíduos de Equipamentos Eléctricos e Electrónicos (EEE). Nós, abaixo-assinado, declaro que o equipamento especificado acima está em conformidade com as diretrizes e normas acima referidas. Data de Emissão: 31 de julho de 2018 Representante legal Assinatura Roger Midgley Sr. Engenheiro Conformidade Regulatória

Navigation menu