Control4 C4FS1Z Wireless Fireplace Switch User Manual 200 00048 Wireless Fireplace Switch Rev A indd

Control4 Wireless Fireplace Switch 200 00048 Wireless Fireplace Switch Rev A indd

UserManual.wiki >

C4FS1Z User Manual

Exhibit 8

Wireless Fireplace Switch Installation GuideSupported Models C4-FS1-Z Wireless Fireplace SwitchSpeciﬁ cations and Supported FixturesThis Control4® Wireless Fireplace Switch operates independently or as part of a Control4 Home-Automation System to enable intelligent control of a gas ﬁ replace. It installs in a standard wall box using typical wiring standards and communicates with other devices through a wireless RF (radio frequency) connection.Power: 120 VAC +/-10% 50/60 Hz300 mW when off400 mW when onSupported Load Types and Ratings:This device requires a neutral AC connection.- Millivolt Low Voltage Control- 24VAC at 240W- 30 V DC at 10AOperating Temperature: All load ratings are based on an ambient temperature of 25 degrees Celsius.Volume: 5.0 Cubic inchesCommunications: ZigBee, IEEE 802.15.4, 2.4 GHz, 15-channel, spread spectrum radioWarnings and ConsiderationsWARNING! Install in accordance with all national and local electrical codes.WARNING! Improper use or installation can cause SERIOUS INJURY, DEATH or LOSS/DAMAGE OF PROPERTY.WARNING! If you are unsure about any part of these instructions, consult a qualiﬁ ed electrician.WARNING! Use this device only with copper or copper clad wire. This prod-uct has NOT been approved for use with Aluminum wiring.WARNING! Do not connect any gas valve or electronic device directly to the 110 to 120VAC power. Refer to your gas appliance’s instructions and wiring diagrams for proper placement of wires. All electronic devices must be wired according to their manufacturer’s instructions.IMPORTANT! Use or modiﬁ cation of this product in a manner not expressly approved by Control4 voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See “Limited 2 Year Warranty.”IMPORTANT! The range and performance of the wireless control system is highly dependent on the following: (1) distance between devices; (2) layout of the home; (3) walls separating devices; and (4) electrical equipment located near devices.b. If you are installing in a multi-gang scenario, partially tighten the mounting screws, leaving 1/8-inch gap between the wall and the yoke plates prior to attaching the black plastic sub-plate. This allows each device in a multi-gang scenario to conform to the sub-plate, creating a single assembly. Secure the multi-gang sub-plate to all devices using the provided sub-plate screws. Then secure the assembly by tightening the wall box screws the remaining 1/8-inch. Do not over-tighten the screws, or you will misalign the ﬂ at plane of the multi-gang wall plate.With the wall plate’s removal slot facing down, push the wall plate onto the Fireplace Switch’s black plastic sub-plate.c. 7. If you are using a Decora-style screw-on wall plate:a. b.c.Do not attach the Fireplace Switch’s black plastic sub-plateAlign the ﬁ replace switch to the wall box and fasten with screws.Fasten the wall plate to the Fireplace Switch with screws.8. 9.Turn ON power at the circuit breaker or replace fuse from fuse box.Test the Fireplace Switch to see if it is working properly. See “Operation and Conﬁ guration” for speciﬁ c instructions.TroubleshootingIf the ﬁ replace does not turn on:• Ensure at least one LED on the face of the switch is lit.• Ensure that the ﬁ replace pilot light is on or the ﬁ replace is in a mode ready to be turned on (refer to the manufacturer’s ﬁ replace documentation).• Ensure circuit breaker is not turned OFF or tripped.• Check for proper wiring.• For help on the installation or operation of this product, email or call the Control4 Technical Support Center. Please provide your exact model number. Contact sup-port@control4.com or see the web site www.control4.com.Fireplace Safety InstructionsWARNING! This Fireplace Switch is intended for installation in standard wall-mounted switching locations. Do no install this Switch inside the ﬁ replace housing or in areas of excessive heat.IMPORTANT! This Fireplace Switch should be installed by a qualiﬁ ed electri-cian or a gas technician who is familiar with gas appliances and gas valves. Incorrect wiring connections will cause damage to the gas valve, electonic module, and/or Fireplace Switch that operates the gas appliance.Installation InstructionsWARNING! In accordance with the National Electric Code (NEC) requirements. • The wires entering the wall box from the 24V or mili-volt system ﬁ replace (low-voltage wiring) must either have a UL rating for 600V or have a protective, non-conductive sleeve/tubing which provides 600V insulation.• Control4 recommends that the low-voltage wiring enter the wall box through a different opening than the high-voltage wiring.• Control4 recommends that good wiring practices be observed when install-ing the device to keep good separation between low and high-voltage wires within the wall box.TURN OFF POWER by switching off the circuit breaker or removing the fuse and test that power is off before wiring!Identify your wiring application (refer to the appropriate diagram on the back page). “Single-Pole (with power source at wall box)Prepare the wires by removing the pre-cut insulation from the appropriate Fireplace Switch leads. Wire insulation should be stripped back 5/8 of an inch from the wire end (as shown).WARNING! Orange wires are only to be used in low-voltage switching. Do not connect them to 120V sources or any loads outside the supported types and ratings.1.2.3.4. Connect the Fireplace Switch wires to the wall box wires using wire nuts according to the relevant wiring diagram. See “Sample Wiring Conﬁ guration.”5. Mount ﬁ replace switch into wall box by partially securing the wall box screws attached to the ﬁ replace switch. Ensure that the word “Top” on the ﬁ replace switch frame is facing up. Bend wires in a zigzag pattern so that they easily fold into the wall box.WARNING! Ground the Wireless Fireplace Switch in accordance with the National Electric Code (NEC) requirements. Although the ﬁ replace switch’s aluminum yoke plate and green ground wire are directly bonded together inside the ﬁ replace switch, DO NOT rely solely upon the yoke plate’s contact with a metal wall box for adequate grounding. Use the ﬁ replace switch’s ground wire to make a secure connection to the safety ground of the electrical system.IMPORTANT! Not grounding this product according to the preceding may result in an installation less immune to damage caused by electrical disturbances, such as lightning, and void the warranty.6. If you are using the Control4 push-on (screw-less) wall plate that shipped with your Fireplace Switch:a. For a single-gang scenario, attach the black plastic sub-plate using the provided sub-plate screws.IMPORTANT! Tighten the screws until the back side of the metal yoke plate is even with the wall surface, but no farther. Over-tightening can damage the ﬁ re-place switch and cause mechanical malfunction. Do NOT use a power screw driver to install this device as this may lead to over-tightening.Sample Wiring Conﬁ gurationSingle-Location Scenario—Power Source at Wall Box NOTE: This device will not function without a neutral AC connection.To wire the Fireplace Switch for a Control4 single-location scenario in which the power is ﬁ rst routed to the wallbox, connect together and cap with a wire nut the wires indicated in the following table: Fireplace Switch Wires Wires in the Wall BoxFrom Power Source To FireplaceWhite (neutral) White (neutral) NoneOrange (load) None White (load)Orange (load) None Black (load)Black (hot) Black (hot) NoneGreen (ground) Green (ground) Green (ground-optional)WARNING! The following wiring diagram is for demonstration purposes only. Refer to your manufacturer’s electronic module and gas valve instructions for correct wiring procedures. Improper installation of electronic devices can cause damage to the module, valve or remote receiver.Operation and Conﬁ gurationOn initial power up, the unit will ﬂ ash the Red/Green/Blue (RGB) LEDs, which can be programmed with different colors for different states or color preferences. To set up this switch for use with a Control4 system, refer to your system setup documentation. To operate this switch as a stand-alone device, refer to the following table.In case there is a power outage, the Wireless Fireplace Switch is equiped with a manual switching mechanism. To close the Fireplace Switch, pull up on the Manual Switch Mecha-nism with your ﬁ ngernail. Operate Fireplace Switch Expected behavior of RGB LEDs:To operate the Fireplace Switch: Top BottomTurn ON: Tap top. Lit, full brightness Not litTurn OFF: Tap bottom. Not lit Lit, full brightnessTo operate the Fireplace Switch manually during a power outage:To turn on the Fireplace Switch: Top BottomPull up on the Manual Switch Mechanism and fully extend (about 0.5”) to close the switch to the ﬁ replace.Not lit Not litCare and CleaningDo NOT paint the Fireplace Switch or its wall plate.Do NOT use any chemical cleaners to clean the switch.Clean surface with a soft damp cloth as needed. Limited 2-Year WarrantyControl4 Corporation (“Control4”) warrants that at the time of ﬁ rst-consumer sale, this product will be free from defects in material and manufacture. Control4 further war-rants that for a period of 2 years (24 months) after initial consumer sale, the product will function in accordance with its speciﬁ cation, provided that it is installed and maintained under normal and proper use. This warranty extends only to products purchased directly from Control4 or an Authorized Control4 Reseller. If the product proves to be defective in material or workmanship during the warranty period, it may be returned to the place of purchase and Control4 will, at its sole option, repair or replace the product with a like product. This warranty provides the consumer purchaser with speciﬁ c legal rights, which may vary per state or country. For complete warranty information, including details on consumer legal rights as well as warranty exclusions, visit www.control4.com/warranty.

Navigation menu