Control4 C4KP6Z Wireless Keypad User Manual 200 00037 Rev A Wireless2 3 6 ButtonKeypad

Control4 Wireless Keypad 200 00037 Rev A Wireless2 3 6 ButtonKeypad

UserManual.wiki >

C4KP6Z User Manual

Exhibit 8

Wireless 2, 3, and 6-Button Keypad Installation GuideSupported Models and RequirementsC4-KP2-Z-W Wireless 2-Button Keypad (White) C4-KP2-Z-B Wireless 2-Button Keypad (Black) C4-KP2-Z-A Wireless 2-Button Keypad (Almond) C4-KP3-Z-W Wireless 3-Button Keypad (White) C4-KP3-Z-B Wireless 3-Button Keypad (Black) C4-KP3-Z-A Wireless 3-Button Keypad (Almond) C4-KP6-Z-W Wireless 6-Button Keypad (White) C4-KP6-Z-B Wireless 6-Button Keypad (Black) C4-KP6-Z-A Wireless 6-Button Keypad (Almond)This device requires a neutral AC connection. SpecificationsThis multi-button keypad is intended for use in a Control4® system. It installs in a standard wall box using typical wiring standards and communicates to the Control4 system using a wireless connection. The specifications are described below.WARNING! To reduce the risk of SERIOUS INJURY or DEATH, turn OFF local electrical power before installing this product, and before installing, removing, or replacing keycaps. IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Control4 is NOT liable for any damage incurred with the misuse of this product. See “Limited 2 Year Warranty.”IMPORTANT! Do NOT use a power screw driver to install this device. If you do, you may overtighten the screws and strip them.IMPORTANT! This is an electronic device with intricate components. Handle and install with care!Installation Instructions1 Ensure that the location and intended use meet the following criteria:• When replacing a traditional 3-way switch, refer to the “Two-Location” sample wiring configurations provided in the following documents:Wireless Dimmer Installation GuideWireless Switch Installation Guide• Install in accordance with all national and local electrical codes.• The required wall box size is specified by the NEC (National Electrical Code). The internal wall box volume occupied by this multi-button keypad is 5.0 cubic inches. • The range and performance of the wireless control system is highly dependent on the following: (1) distance between devices; (2) layout of the home; (3) walls separating devices; and (4) electrical equipment located near devices.• If you are planning to use engraved keycaps for 3-Button and 6-Button Keypads, DO NOT continue until you have read the “Replace Keycaps” section.• If installing a multi-button keypad in a multi-gang installation, DO NOT continue until you have read the “Multi-Gang Installations” section.WARNING! To reduce the risk of SERIOUS INJURY or DEATH, turn OFF local electrical power before installing this product. 2 Turn off the local electrical power by either switching off the circuit breaker or removing the fuse from the fuse box. To ensure the wires do NOT have power running to them, use an inductive voltage detector.WARNING! As with any electrical device, improper use or installation can cause SERIOUS INJURY or DEATH. It is important that you understand the particular wiring configuration of your installation before proceeding. Note: The wall box wiring shown in this document is an example. Your wire colors and functions may differ. If you are not sure which wires are the Hot, Neutral, and Ground wires, have a trained electrician do the installation.3 Prepare each wire. Wire insulation should be stripped back 5/8 of an inch from the wire end (as shown). WARNING! Ground the Wireless Keypad in accordance with the National Electric Code (NEC) requirements. Although the keypad's aluminum yoke plate and green ground wire are directly bonded together inside the keypad, DO NOT rely solely upon the yoke plate's contact with a metal wall box for adequate grounding. Use the keypad’s ground wire to make a secure connection to the safety ground of the electrical system.IMPORTANT! Not grounding this product according to the preceding may result in an installation less immune to damage caused by electrical disturbances, such as lightning, and void the warranty.4 If you need to “Replace Keycaps” or do “Multi-Gang Installations”, then refer to those sections (to the right) before continuing.5 Identify and connect the multi-button keypad wires to the wall box wires using wire nuts. Note: Wall box wires can differ depending upon how the box was wired by your electrician.To wire the multi-button keypad, connect and cap with a wire nut the wires indicated in the following table.6 Fit wires back into the wall box. Bend the wires in a zigzag pattern so that they easily fold into the wall box.7 If you are using the Control4 push-on (screw-less) wall plate that shipped with your multi-button keypad:a. Align the multi-button keypad to the wall box and fasten with screws. Tighten the screws until the back side of the metal yoke plate is even with the wall surface, but no farther. Overtightening can warp the multi-button keypad and cause mechanical malfunction.b. With the wall plate’s removal slot facing down, push the wall plate onto the dimmer’s black plastic sub-plate.8 If you are using a Decora-style screw-on wall plate:a. Remove the multi-button keypad’s black plastic sub-plate and store it for future use (in case you later decide to use the Control4 wall plate).b. Align the multi-button keypad to the wall box and fasten with screws.c. Fasten the wall plate to the multi-button keypad with screws.9 Turn ON power at the circuit breaker or replace fuse from fuse box.10 Ensure that all LEDs on the front are lit. Replace Keycaps Applies to 3-Button and 6-Button Keypads OnlyWARNING! To avoid SERIOUS INJURY or DEATH, turn OFF local electrical power before installing, removing, or replacing keycaps.Control4 offers standard engraved keycaps and custom engraved keycaps (both sold separately) to enable you to personalize 3-Button and 6-Button Keypads. Note: Custom engraving is not available for 2-Button Keypads.If you are replacing keycaps:1. Turn off local electrical power.2. Remove the screw-less or screw-on wall plate from the multi-button key-pad.3. Remove the black plastic sub-plate from the multi-button keypad by removing the screw at the top and bottom of the device.4. Pinch both sides of the keycap retainer at both ends—working first at the top, then the bottom—to gently remove the retainer. DO NOT pry the retainer off with a screw driver.5. Remove the default keycaps from the keycap retainer and replace each one with the engraved keycap of your choice. Be sure to place the LED at the top. 6. Carefully snap the retainer back into place, taking care not to damage the retainer clips. 7. Reattach the sub-plate with the screws. 8. Reattach the wall plate.Multi-Gang InstallationsMulti-gang installations are configurations in which 2 or more devices are installed side-by-side in the same wall box. For multi-gang installations: If using a Control4 push-on (screw-less) multi-gang wall plate: Remove the individual black plastic sub-plate from each device and replace them with the multi-gang sub-plate that shipped with your Control4 multi-gang wall plate. The use of the multi-gang sub-plate inherently aligns and spaces each device properly. TIP: For ease of installation, each device’s yoke plate must be even and aligned in a flat plane so that the multi-gang sub-plate can sit flat against all of the devices. This can be accomplished by initially not screwing the devices tightly against the wall box, leaving about 1/8 of an inch gap between the wall and the yoke plates. This allows each device to move and conform to the sub-plate. Using the new screws supplied with the multi-gang sub-plate, secure the multi-gang sub-plate to all devices to create a single structure. Then secure the structure by tightening the wall box screws the remaining 1/8 of an inch. Do not over-tighten any of the screws or you will misalign the flat plane of the multi-gang wall plate. If using a Decora-style screw-on multi-gang wall plate: Remove the black plastic sub-plate from each device, just as you would for a single device (see step 8), and store it for future use in case you later decide to use the Control4 wall plate.Operation and ConfigurationOn initial power up, the unit will flash the Red/Green/Blue (RGB) LEDs, which can be programmed with different colors for different states or color preferences. To set up this multi-button keypad for use with a Control4 system, refer to your system setup documentation. Power: 120 V~, 60/50 Hz, 490 mWSupported Load Types:Not Applicable. This device does not directly control a load.Communications: IEEE 802.15.4, 2.4 GHz, 15-channel, spread spectrum radioMulti-Button Keypad Wires (2, 3, or 6-Button)Wires in Wall Box White (neutral) White (neutral) Green (ground) Green (ground)Black (hot) Black (hot)