Control4 C4SW101Z Wireless Switch User Manual 200 00036 Rev A WirelessSwitch

Control4 Wireless Switch 200 00036 Rev A WirelessSwitch

UserManual.wiki >

Control4 >

C4SW101Z User Manual HTML Version

Exhibit 8

Sample Wiring Configurations

Wireless Switch

Installation Guide

Supported Models

C4-SW101-Z-W Wireless Switch (White)

C4-SW101-Z-B Wireless Switch (Black)

C4-SW101-Z-A Wireless Switch (Almond)

This device requires a neutral AC connection.

Specifications and Supported Fixtures

This Control4® Wireless Switch operates independently or as part of a Control4® home

automation system to enable intelligent lighting control. It installs in a standard wall box

using typical wiring standards and communicates with other devices through a wireless

RF (radio frequency) connection.

IMPORTANT! Use or modification of this product in a manner not expressly

approved by Control4 voids your warranty. Further, Control4 is NOT liable for

any damage incurred with the misuse of this product. See "Limited 2 Year

Warranty."

IMPORTANT! The range and performance of the wireless control system is

highly dependent on the following: (1) distance between devices; (2) layout of

the home; (3) walls separating devices; and (4) electrical equipment located

near devices.

Installation Instructions

1 TURN OFF POWER by switching off the circuit breaker or

removing the fuse and test that power is off before wiring!

2 Identify your wiring application (refer to the appropriate diagram

in “” on the back page).

• "Single-Pole (with power source at wall box) - see Figure 1

• "3-Way (with power source at wall box) - see Figure 2

3 Prepare wires by removing pre-cut

insulation from the appropriate switch

leads. Wire insulation should be stripped

back 5/8 of an inch from the wire end (as

shown).

4 Connect the switch wires to the wall box

wires using wire nuts according to the relevant

wiring diagram. See “Sample Wiring

Configurations.”

5 Mount Switch into wall box by partially securing

the wall box screws attached to the switch. Ensure that

the word "Top" on the switch frame is facing up. Bend

wires in a zigzag pattern so that they easily fold into the

wall box.

WARNING! Ground the Wireless Switch in

accordance with the National Electric Code (NEC) requirements. Although the

switch's aluminum yoke plate and green ground wire are directly bonded

together inside the switch, DO NOT rely solely upon the yoke plate's contact

with a metal wall box for adequate grounding. Use the switch's ground wire to

make a secure connection to the safety ground of the electrical system.

IMPORTANT! Not grounding this product according to the preceding may

result in an installation less immune to damage caused by electrical

disturbances, such as lightning, and void the warranty.

6 If you are using the Control4 push-on (screw-less) wall plate that shipped with

your switch:

a. For a single-gang scenario, attach the black plastic sub-plate using the

provided sub-plate screws.

IMPORTANT! Tighten the screws until the back side of the metal yoke plate

is even with the wall surface, but no farther. Over-tightening can damage the

switch and cause mechanical malfunction. Do NOT use a power screw driver to

install this device as this may lead to over-tightening.

b. If you are installing in a multi-gang scenario, only partially tighten the

mounting screws, leaving about 1/8 of an inch gap between the wall and the

yoke plates prior to attaching the black plastic sub-plate. This allows each

device in a multi-gang scenario to conform to the sub-plate, creating a single

assembly. Secure the multi-gang sub-plate to all devices using the provided

sub-plate screws. Then secure the assembly by tightening the wall box

screws the remaining 1/8 of an inch. Do not over-tighten any of the screws

or you will misalign the flat plane of the multi-gang wall plate.

c. With the wall plate's removal slot facing down, push the wall

plate onto the switch's black plastic sub-plate.

7 If you are using a Decora-style screw-on wall plate:

a. Do not attach the switch's black plastic sub-plate

b. Align the switch to the wall box and fasten with screws.

c. Fasten the wall plate to the switch with screws.

8 Turn ON power at the circuit breaker or replace fuse from fuse

box.

9 Test the switch to see if it is working properly. See "Operation

and Configuration" for specific instructions.

Power: 120 VAC +/-10% 50/60 Hz

300 mW when off

850 mW when on

Supported Load

Types and Ratings:

120 VAC 1000 W Resistive

120 VAC 500 W Tungsten

120 VAC 1000 W Electronic Low Voltage

120 VAC 1000 W Fluorescent Light Fixtures

120 VAC 1000 W Magnetic Low Voltage

Operating

Temperature:

All load ratings are based on an ambient temperature of

25 degrees Celsius.

Volume: 5.0 Cubic inches

Communications: ZigBee, IEEE 802.15.4, 2.4 GHz, 15-channel, spread

spectrum radio

Warnings & Considerations

WARNING! Install in accordance with all national and local electrical codes.

WARNING! Improper use or installation can cause SERIOUS INJURY,

DEATH or LOSS/DAMAGE OF PROPERTY.

WARNING! If you are unsure about any part of these instructions, consult a

qualified electrician.

WARNING! Use this device only with copper or copper clad wire. This product

has NOT been approved for use with Aluminum wiring.

Single-Location Scenario—Power Source at Wall Box

NOTE: This device will not function without a neutral AC connection.

To wire the switch for a Control4 single-location scenario in which the

power is first routed to the wallbox, connect together and cap with a

wire nut the wires indicated in the following table:

Switch Wires Wires in the Wall Box

From Power Source To Light Fixture

White (neutral) White (neutral) White (neutral)

Red (load) None black (load)

Black (hot) Black (hot) None

Green (ground) Green (ground) Green (ground)

Two-Location Scenario—Power Source at Wall Box

NOTE: This device will not function without a neutral AC connection.

To wire the switch and a multi-button keypad in a two-location scenario

(Control4’s 3-way-switch solution) where the power is first routed to the wall

box, do the following:

1. Wire the switch into Wall Box #1 by connecting together and capping with a

wire nut the following wires:

Switch Wires Wires in Wall Box 1

From Power

Source To Light Fixture To Wall Box 2

White (neutral) White (neutral) White (neutral) White (neutral)

Red (load) None Black (load) None

Black (hot) Black (hot) None Black (traveler)

Green (ground) Green (ground) Green (ground) Green (ground)

2. Wire the multi-button keypad into Wall Box #2 by connecting together and

capping with a wire nut the following wires:

Multi-Button Keypad Wires Wires in Wall Box 2

(from Wall Box 1)

White (neutral) White (neutral)

Green (ground) Green (ground)

Black (traveler) Black (traveler)

Optional Antenna Extension

In some installation scenarios, it may be desirable to enhance the Switch's wireless (RF)

transmission capabilities. This may be needed to overcome issues such as local

interference from other devices, range considerations due to the distance between devices

or the use of metallic faceplates. The Control4 Wireless Switch has been designed with a

wire whip antenna coiled underneath the plastic button that can be extended to

accommodate such scenarios. Instructions for extending the antenna are provided below.

WARNING! To avoid risk of electrical shock that may cause personal injury or

damage to the Switch, this procedure should be performed prior to connecting the

switch at the wall box.

CAUTION! Risk of Equipment Damage. This procedure enables advanced

functionality and should only be performed by a competent trained installer.

1 Remove the plastic button frame by squeezing

the side tabs near the top and bottom of the

button and pulling outward. A small flat-head

screw driver can also be used to assist in

releasing the tabs.

2 Once the button has been removed, detach the

radio board from its connector by gently pulling

away from the switch frame.

3 Slip the end of the antenna out of the radio

board hole and uncoil it, being careful not to

exert undue tension on the wire. Once uncoiled,

thread the antenna wire under the plastic spacer

at the bottom of the radio board.

4 Re-attach the radio card to the switch frame by

carefully aligning the connector and pressing gently. Then

re-attach the button and button frame by aligning the

button frame securement tabs with the appropriate slots on

the switch frame and pushing gently. Ensure that the

antenna is routed through the small notch on the bottom

left-hand side of the button frame provided for this

purpose. Once the button has been re-attached, proceed

with the standard installation procedure for wiring the

switch to the light load and securing it into the wall box, as

described in Step 1 through Step 5 of “Installation

Instructions.”

5 The antenna has been designed to extend well beyond

the faceplate. For optimal performance, it should be

oriented in a vertical plane below the switch. To enable

this without leaving the antenna visible to the end user,

a very small hole should be made in the wall just below

the switch frame and the antenna inserted through the

hole back into the wall. Once the antenna has been

routed into the wall, proceed with standard installation

of the switch sub-plate and faceplate, as described in

Step 6 and Step 7 of “Installation Instructions.”

CAUTION! Risk of Equipment Damage. The

antenna must not be inserted into the junction box containing high voltage wires.

IMPORTANT! Do not shortened or cut the antenna in any way as this may

seriously impair transmission capabilities.

Troubleshooting

If light does not turn on:

•Ensure at least one LED on the face of the switch is lit.

•Ensure the light bulb is not burned out and is screwed in tightly.

•Ensure circuit breaker is not turned OFF or tripped.

•Check for proper wiring (see the “”section).

•For help on the installation or operation of this product, email or call the Control4

Technical Support Center. Please provide your exact model number. Contact

support@control4.com or see the web site www.control4.com.

Operation and Configuration

On initial power up, the unit

will flash the Red/Green/

Blue (RGB) LEDs, which

can be programmed with

different colors for different

states or color preferences.

To set up this switch for use

with a Control4 system,

refer to your system setup

documentation.

To operate this switch as a stand-alone device, refer to the following tables.

Limited 2 Year Warranty

Control4 Corporation ("Control4") warrants that at the time of first-consumer sale, this

product will be free from defects in material and manufacture. Control4 further warrants

that for a period of 2 years (24 months) after initial consumer sale, the product will function

in accordance with its specification, provided that it is installed and maintained under

normal and proper use. This warranty extends only to products purchased directly from

Control4 or an Authorized Control4 Reseller. If the product proves to be defective in

material or workmanship during the warranty period, it may be returned to the place of

purchase and Control4 will, at its sole option, repair or replace the product with a like

product. This warranty provides the consumer purchaser with specific legal rights, which

may vary per state or country. For complete warranty information, including details on

consumer legal rights as well as warranty exclusions, visit www.control4.com/warranty.

Regulatory Compliance

FCC

FCC ID: R33C4SW101Z

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT! Any changes or modifications not expressly approved by the

party responsible for compliance could void the user’s authority to operate this

equipment.

ETL Statement

ETL Control Number: 3017581

This product has been tested by ETL and was found to comply with the Standard for Safety

for Industrial Control Equipment:

•UL/ANSI Standard 508 (Seventeenth Edition)

•CSA Standard C22.2 No. 14-05

Industry Canada

This Class B digital apparatus complies with Canada ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

About this Document

Control4 logo are registered trademarks of Control4 Corporation. All trademarks are

properties of their respective owners. Part Number: 200-00036 Rev A

Operate Switch Expected behavior of RGB LEDs:

To operate switch: Top Bottom

Turn ON: Tap top. Lit, full brightness Not lit

Turn OFF: Tap bottom. Not lit Lit, full brightness

Care and Cleaning

Do NOT paint switch or its wall plate.

Do NOT use any chemical cleaners to clean the switch.

Clean surface with a soft damp cloth as needed.

Sample Wiring Configurations

Wireless Fireplace

Switch Installation

Guide

Supported Models

C4-FS101-Z-W Wireless Fireplace Switch (White)

C4-FS101-Z-B Wireless Fireplace Switch (Black)

C4-FS101-Z-A Wireless Fireplace Switch (Almond)

This device requires a neutral AC connection.

Specifications and Supported Fixtures

This Control4® Wireless Fireplace Switch operates independently or as part of a

Control4® home automation system to enable intelligent lighting control. It installs in a

standard wall box using typical wiring standards and communicates with other devices

through a wireless RF (radio frequency) connection.

IMPORTANT! Use or modification of this product in a manner not expressly

approved by Control4 voids your warranty. Further, Control4 is NOT liable for

any damage incurred with the misuse of this product. See "Limited 2 Year

Warranty."

IMPORTANT! The range and performance of the wireless control system is

highly dependent on the following: (1) distance between devices; (2) layout of

the home; (3) walls separating devices; and (4) electrical equipment located

near devices.

Installation Instructions

1 TURN OFF POWER by switching off the circuit breaker or

removing the fuse and test that power is off before wiring!

2 Identify your wiring application (refer to the appropriate diagram

in “” on the back page).

• "Single-Pole (with power source at wall box) - see Figure 1

• "3-Way (with power source at wall box) - see Figure 2

3 Prepare wires by removing pre-cut

insulation from the appropriate fireplace

switch leads. Wire insulation should be

stripped back 5/8 of an inch from the wire

end (as shown).

4 Connect the fireplace switch wires to the

wall box wires using wire nuts according to the

relevant wiring diagram. See “Sample Wiring

Configurations.”

5 Mount fireplace switch into wall box by partially

securing the wall box screws attached to the fireplace

switch. Ensure that the word "Top" on the fireplace

switch frame is facing up. Bend wires in a zigzag

pattern so that they easily fold into the wall box.

WARNING! Ground the Wireless Fireplace Switch

in accordance with the National Electric Code (NEC) requirements. Although

the fireplace switch's aluminum yoke plate and green ground wire are directly

bonded together inside the fireplace switch, DO NOT rely solely upon the yoke

plate's contact with a metal wall box for adequate grounding. Use the fireplace

switch's ground wire to make a secure connection to the safety ground of the

electrical system.