Control4 C4SW1Z Wireless Switch User Manual 200 00036 Rev D WirelessSwitch
Control4 Wireless Switch 200 00036 Rev D WirelessSwitch
Control4 >
Exhibit 8
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1112926 |
| Application ID | oOpYTyjMGklU1q9dHr68UQ== |
| Document Description | Exhibit 8 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 78.07kB (975910 bits) |
| Date Submitted | 2009-05-19 00:00:00 |
| Date Available | 2009-05-19 00:00:00 |
| Creation Date | 2004-10-26 09:05:05 |
| Producing Software | Acrobat Distiller 9.0.0 (Windows) |
| Document Lastmod | 2009-05-18 14:13:13 |
| Document Title | 200-00036 Rev D_WirelessSwitch.fm |
| Document Creator | FrameMaker 7.1 |
| Document Author: | bnoyce |
Installation Instructions
TURN OFF POWER by switching off the circuit breaker or
removing the fuse and test that power is off before wiring!
Identify your wiring application (refer to the appropriate diagram
in “” on the back page).
•
•
Wireless Switch
Installation Guide
"Single-Pole (with power source at wall box) - see Figure 1
"3-Way (with power source at wall box) - see Figure 2
Prepare wires by removing pre-cut
insulation from the appropriate switch
leads. Wire insulation should be stripped
back 5/8 of an inch from the wire end (as
shown).
Connect the switch wires to the wall box
wires using wire nuts according to the relevant
wiring diagram.
Mount Switch into wall box by partially securing
the wall box screws attached to the switch. Ensure that
the word "Top" on the switch frame is facing up. Bend
wires in a zigzag pattern so that they easily fold into the
wall box.
Sample Wiring Configurations
Single-Location Scenario—Power Source at Wall Box
NOTE: This device will not function without a neutral AC connection.
To wire the switch for a Control4 single-location scenario in which the
power is first routed to the wallbox, connect together and cap with a
wire nut the wires indicated in the following table:
Wires in the Wall Box
Switch Wires
White (neutral)
From Power Source
To Light Fixture
White (neutral)
White (neutral)
black (load)
Red (load)
None
Black (hot)
Black (hot)
None
Green (ground)
Green (ground)
Green (ground)
Supported Models
C4-SW1-Z Wireless Switch
Specifications and Supported Fixtures
This Control4® Wireless Switch operates independently or as part of a Control4® home
automation system to enable intelligent lighting control. It installs in a standard wall box
using typical wiring standards and communicates with other devices through a wireless
RF (radio frequency) connection.
Power:
Two-Location Scenario—Power Source at Wall Box
WARNING! Ground the Wireless Switch in
accordance with the National Electric Code (NEC) requirements. Although the
switch's aluminum yoke plate and green ground wire are directly bonded
together inside the switch, DO NOT rely solely upon the yoke plate's contact
with a metal wall box for adequate grounding. Use the switch's ground wire to
make a secure connection to the safety ground of the electrical system.
120 VAC +/-10% 50/60 Hz
300 mW off
400 mW on
Supported Load
Types and Ratings:
IMPORTANT! Not grounding this product according to the preceding may
result in an installation less immune to damage caused by electrical
disturbances, such as lightning, and void the warranty.
120 VAC 1000 W Resistive
120 VAC 500 W Tungsten
120 VAC 1000 W Electronic Low Voltage
Communications:
ZigBee, IEEE 802.15.4, 2.4 GHz, 15-channel, spread
spectrum radio
provided sub-plate screws.
IMPORTANT! Tighten the screws until the back side of the metal yoke plate
is even with the wall surface, but no farther. Over-tightening can damage the
switch and cause mechanical malfunction. Do NOT use a power screw driver to
install this device as this may lead to over-tightening.
b. If you are installing in a multi-gang scenario, only partially tighten the
mounting screws, leaving about 1/8 of an inch gap between the wall and the
yoke plates prior to attaching the black plastic sub-plate. This allows each
device in a multi-gang scenario to conform to the sub-plate, creating a single
assembly. Secure the multi-gang sub-plate to all devices using the provided
sub-plate screws. Then secure the assembly by tightening the wall box
screws the remaining 1/8 of an inch. Do not over-tighten any of the screws
or you will misalign the flat plane of the multi-gang wall plate.
c. With the wall plate's removal slot facing down, push the wall
plate onto the switch's black plastic sub-plate.
5.0 Cubic inches
Warnings & Considerations
WARNING! Install in accordance with all national and local electrical codes.
WARNING! Improper use or installation can cause SERIOUS INJURY,
DEATH or LOSS/DAMAGE OF PROPERTY.
WARNING! Use this device only with copper or copper clad wire. This product
has NOT been approved for use with Aluminum wiring.
approved by Control4 voids your warranty. Further, Control4 is NOT liable for
any damage incurred with the misuse of this product. See "Limited 2 Year
Warranty."
IMPORTANT! The range and performance of the wireless control system is
highly dependent on the following: (1) distance between devices; (2) layout of
the home; (3) walls separating devices; and (4) electrical equipment located near
devices.
If you are using a Decora-style screw-on wall plate:
a. Do not attach the switch's black plastic sub-plate
b. Align the switch to the wall box and fasten with screws.
c. Fasten the wall plate to the switch with screws.
WARNING! If you are unsure about any part of these instructions, consult a
qualified electrician.
IMPORTANT! Use or modification of this product in a manner not expressly
If you are using the Control4 push-on (screw-less) wall plate that shipped with
your switch:
a. For a single-gang scenario, attach the black plastic sub-plate using the
This device requires a neutral AC connection.
Operating
Temperature:
Volume:
1. Wire the switch into Wall Box #1 by connecting together and capping with a
wire nut the following wires:
Wires in Wall Box 1
Switch Wires
120 VAC 1000 W Magnetic Low Voltage
All load ratings are based on an ambient temperature of
25 degrees Celsius.
NOTE: This device will not function without a neutral AC connection.
To wire the switch and a multi-button keypad in a two-location scenario
(Control4’s 3-way-switch solution) where the power is first routed to the wall
box, do the following:
Turn ON power at the circuit breaker or replace fuse from fuse
box.
Test the switch to see if it is working properly. See "Operation
and Configuration" for specific instructions.
From Power
Source
To Light Fixture
To Wall Box
White (neutral)
White (neutral)
White (neutral)
White (neutral)
Red (load)
None
Black (load)
None
Black (hot)
Black (hot)
None
Black (traveler)
Green (ground)
Green (ground)
Green (ground)
Green (ground)
2. Wire the multi-button keypad into Wall Box #2 by connecting together and
capping with a wire nut the following wires:
Multi-Button Keypad Wires
Wires in Wall Box 2
(from Wall Box 1)
White (neutral)
White (neutral)
Green (ground)
Green (ground)
Black (traveler)
Black (traveler)
Troubleshooting
Regulatory Compliance
If light does not turn on:
FCC
•
•
•
•
•
Ensure at least one LED on the face of the switch is lit.
Ensure the light bulb is not burned out and is screwed in tightly.
Ensure circuit breaker is not turned OFF or tripped.
Check for proper wiring (see the “”section).
For help on the installation or operation of this product, email or call the Control4
Technical Support Center. Please provide your exact model number. Contact
support@control4.com or see the web site www.control4.com.
FCC ID: R33C4SW1Z
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Operation and Configuration
On initial power up, the unit
will flash the Red/Green/
Blue (RGB) LEDs, which
can be programmed with
different colors for different
states or color preferences.
To set up this switch for use
with a Control4 system,
refer to your system setup
documentation.
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT! Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this
equipment.
ETL Statement
To operate this switch as a stand-alone device, refer to the following tables.
Operate Switch
Expected behavior of RGB LEDs:
To operate switch:
Top
Bottom
Turn ON: Tap top.
Lit, full brightness
Not lit
Turn OFF: Tap bottom.
Not lit
Lit, full brightness
ETL Control Number: 3129831
This product has been tested by ETL and was found to comply with the Standard for
Safety for Industrial Control Equipment:
•
•
UL/ANSI Standard 508 (Seventeenth Edition)
CSA Standard C22.2 No. 14-05
Care and Cleaning
Do NOT paint switch or its wall plate.
Do NOT use any chemical cleaners to clean the switch.
Clean surface with a soft damp cloth as needed.
Industry Canada
IC ID: 7848A-C4SW1Z
This Class B digital apparatus complies with Canada ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Limited 2 Year Warranty
Control4 Corporation ("Control4") warrants that at the time of first-consumer sale, this
product will be free from defects in material and manufacture. Control4 further warrants
that for a period of 2 years (24 months) after initial consumer sale, the product will function
in accordance with its specification, provided that it is installed and maintained under
normal and proper use. This warranty extends only to products purchased directly from
Control4 or an Authorized Control4 Reseller. If the product proves to be defective in
material or workmanship during the warranty period, it may be returned to the place of
purchase and Control4 will, at its sole option, repair or replace the product with a like
product. This warranty provides the consumer purchaser with specific legal rights, which
may vary per state or country. For complete warranty information, including details on
consumer legal rights as well as warranty exclusions, visit www.control4.com/warranty.
Protected under U.S. Patents 7,106,261 and licensed under U.S. Patents 5,905,442 and
5,982,103
About this Document
United States Patents Pending. ©2009 Control4. All rights reserved. Control4, the Control4
logo and Everyday Easy are registered trademarks or trademarks of Control4 Corporation
in the United States and/or other countries. All other names or brands may be claimed as
property by their respective owners. Pricing and specifications subject to change without
notice. Part Number: 200-00036 Rev D
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Print high-res Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Creator Tool : FrameMaker 7.1 Modify Date : 2009:05:18 14:13:13-06:00 Create Date : 2004:10:26 09:05:05Z Metadata Date : 2009:05:18 14:13:13-06:00 Format : application/pdf Title : 200-00036 Rev D_WirelessSwitch.fm Creator : bnoyce Producer : Acrobat Distiller 9.0.0 (Windows) Document ID : uuid:f03f6835-5d6f-4431-a754-14dad8a73ecb Instance ID : uuid:2bbcfb95-3b48-44e0-91ad-5f1848b8d142 Page Count : 2 Author : bnoyceEXIF Metadata provided by EXIF.tools