Controlled Entry Distributors 418ELPWV Model 418ELPWxV User Manual 418LT

Controlled Entry Distributors, Inc. Model 418ELPWxV 418LT

Exhibit 8

1A - General informationTransmitter Solutions - Stingray 418ELPWxV is a visor transmitteroperating at 418 MHz in ASK modulation. It has been designed for theprogrammable telephone entry systems, anti-burglar systems andaccess control systems operating at 418 MHz. The code sent by thetransmitter includes a 16 bit security code which allows up to 65,536code combinations and 8 bits of facility code which allows up to 2561B - Technical specificationsNumber of keys: 1 / 2Battery life: 12 - 18 monthsCurrent consumption : 20 mAOperating frequency : 418 MHzCode combinations : 65536Facility codes : 256Modulation : AM / ASKRated e.r.p. : 50 - 100 mWRange in free space: 60 - 120 ydOperating temperature: -20 ÷ +55 °COverall dimensions: 3.26 x 1.88 x 0.62 inWeight: 20 gr.Supply : 1 Alkaline Battery 12V type 23Afacility codes.Each transmitter is individually numbered and can be used with anyreceiver capable of receiving a 26 bit input.The 23A alkaline battery has a life of about 12-18 months.The product fully complies with Part 15 of FCC Regulations.1C - Main featuresTRANSMITTER STINGRAY 418ELPWxVManual1A - General information1B - Technical specifications1C - Main features1D -Types1 - TRANSMITTER INTRODUCTION2 - NUMBERING3 - PROGRAMMING4 - OPERATION5 - BATTERY ACCESSCONTENTS6 - TROUBLESHOOTINGTransmitterSolutionsThank you for choosing a Transmitter Solutions product .Please read this manual carefully before using the product.Made in Italy. Copyright © 2006 by Transmitter Solutions418ELPW1V 418ELPW2VPush-buttonAGreenPush-buttonBgreenKey holderringBatterydoorRedLEDEnclosurelight-grey
2 - NUMBERING5 - BATTERY ACCESS6 - TROUBLESHOOTINGTo access the battery slide out the battery doorPlace the alkaline battery between the 2 contacts.Respect the right polarity as indicated on the bottom of the box.23ANOTE: Please dispose of the batteries properly according to local laws andregulations.Test proper battery installation by verifying that the red LED illuminates wheneither button is pushed.Each transmitter is manufactured and sold with a different factory set sequencenumber and facility code.+_23ABatteryPolarityOPENFAULT SOLUTIONThe operating range is reducedCheck to verify thetransmitter is programmedinto your systemReplace the transmitterbatteriesReplace the transmitterbatteriesThe system does not receiver thetransmitter signal.The transmitter LED is ONThe system does not receiver thetransmitter signal.The transmitter LED will not light3 - PROGRAMMINGThe transmitter facility code and sequence number must be programmed into yoursystem memory. Your own installer or reseller will provide you the necessaryinstructions for your system.4 - OPERATIONa. Firmly depress either button until the small red LED illuminates.b. After the LED has illuminated, release the button. If the device you are attemptingto activate does not respond, repeat steps a. and b. or consult section 6(Troubleshooting) of this manual.IS-T11418CCUK Rev. 0 del 27.06.06The warranty period of 418 transmitters is 24 months,beginning from the manufacturing date of the transmitter. During this period, if theproduct does operate correctly, due to a defective component, the product will berepaired or replaced at the sole discretion of .The warranty does not extend to the transmitter case which can be damaged byconditions outside the control of or to battery life.Transmitter SolutionsTransmitter SolutionsTransmitter SolutionsWARRANTYTRANSMITTER SOLUTIONS2505 Chandler Avenue, Suite, 1Las Vegas, NV 89120 -(866) 975-0101 - (866) 975-0404 Faxsales@transmittersolutions.com1D - TypesSTINGRAY 418ELPW1V : 1 button transmitterSTINGRAY 418ELPW2V : 2 button transmitterFCC ID : SU7418ELPWVThis device complies with FCC RulesOperation is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) this device must accept interference received, includinginterference that may cause undesired operation.Part. 15 of theNoticeAny changes or modification to equipment not expresslyapproved by could void the manufacturer’s warranty and theuser’s authority to operate this product.Transmitter SolutionsTransmitter Solutions

Navigation menu