Convoy Technologies CT-W1000KIT Wireless video and audio transmitter User Manual

CONVOY TECHNOLOGIES L.L.C. Wireless video and audio transmitter

User Manual

Convoy Technologies Wireless video and audio transmitter MODEL : CT-W1000KIT, CT-W1000KIT-MCN, CT-W1000TX, CT-W1000RX, 1490159, 1490161
contents 1 INTRODUCTION .............................................................................. 3 2 INSTALLATION ........................................................................... 3 3 USAGE INSTRUCTION........................................................................ 4 3 SPECIFICATIONS .............................................................................. 5
INTRODUCTION Convoy Wireless Module is a series of low cost and high performance digital Wireless transceiver module for wireless rearview, wireless camera applications which integrates MPEG4 codec , FHSS base band , RF transceiver ,AD&Flash, CVBS PAL/NTSC System input. PowerSupplyByCar 12V
USAGE INSTRUCTION 1. Ensure to follow above connection diagram to install the modules properly into your vehicle. 2. LED light status (ON = POWER ON & CONNECTED, FLASHING= PAIRING MODE, OFF = POWER OFF or DISCONNECTED) 3. You may choose to perform a “Pairing” to re-establish connection between modules by procedure below: ‐ Holding the center pairing button on Receiver Module until LED light constantly flashing. ‐ The connected Monitor Display will display “PAIRING” with 50 second count down. ‐ Holding the center pairing button on Transmitter Module until LED light constantly flashing. ‐ The connected Monitor Display will display “SAVED DATA” for successful Pairing and then camera image will be displayed.
SPECIFICATION DC Characteristics POWER SUPPLY DC 12V TX Current Consumption TYPE:330Ma, Max.400Ma Environmental Specification Operating Temperature -10~+60 ºC Storing Temperature -30~+85 ºC Operating humidity 85%RH BASEBAND SPEC. 2SEC Max. RE POWER ON TBD Max. SE/AV 100ms Max. RE Latency TBD Max. SE/AV VGA/640X480 RE Resolution PAL:720X576/NTSC:720X480 SE/AV 30f/s Frame Rate NTSC:30f/s/PAL: 25f/s SE/AV Video Codec MPEG4 TX Video in System PAL/NTSC Auto detection RX Video out System PAL/NTSC Auto detection Audio Codec MP3 1Channel 8KHz M RE/SE Voice Sample Rate 48KHz AV 340Hz~3.4KHz RE/SE Voice Frequency Band 20Hz~20KHz AV ID / BIT Pairing 22(4KK) SYSTEM Architecture ARM9(32Bit) SOC Idle Screen Blue Screen Video Characteristics Video Output impedance 75Ω, Typ. Video Output Level 1Vp-p, Typ. Video Polarity NEGATIVE Video Frequency Response ±5 dB, Max. 50Hz ~ 6MHz Differential Gain ±5 %, Max Differential Phase ±5 Deg., Max S/N 50dB, Min
Audio Audio Output impedance 200KΩ, Typ. Audio Output Level 5mv~0.5Vp-p, Typ. S/N(340Hz ~ 3.4kHz) 63dB, Min THD:(340Hz~ 3.4kHz,0.5p-p ) 0.1 %, Max Outline Size 147 x 87 mm Weight 200g/box
FCC Certification Requirements Caution: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.

Navigation menu