Coppernic HFELYWAP3 RFID MODULE HF-ELY-WAP3 User Manual RFID Module HF ELY WAP3 1

Coppernic RFID MODULE HF-ELY-WAP3 RFID Module HF ELY WAP3 1

Contents

USERS MANUAL

April 26, 2011 DPD 110052 A00 Sheet 1 of 6 MORPHOCHECK 2 EXPANSION MODULE INSTRUCTIONS Important: All Approval and safety information is outlined in the ‘Workabout pro 3 Handheld-computer User Manual’. This manual is available on our website www.psion.com through the Teknet extranet Easily installable expansion modules for the WORKABOUT PRO 3 allow you to customise this hand-held to meet your specific mobile computing requirements. This chapter outlines how to install the SAM. Before installing SAM in the WORKABOUT PRO 3, all power sources must be turned off. • Remove the batteries. If your unit is using AC power, disconnect it. • Slide the switch to position OFF to shut off internal battery power. With the power shut down, you can install the SAM. MORPHOCHECK 2 2X0 MORPHOCHECK 2 300 2D Imager Smart Card Reader Finger Print Reader RFID Reader OCR Reader
April 26, 2011 DPD 110052 A00 Sheet 2 of 6 MORPHOCHECK 2 200 • Unscrew the screws to remove the back plate. MORPHOCHECK 2 250 • Unscrew the screws to remove the 2D Imager. MORPHOCHECK 2 300 • Unscrew the screws to remove the OCR Reader. WARNING TO THE GROUND AND FLEX CONNECTIONS
April 26, 2011 DPD 110052 A00 Sheet 3 of 6 • Open the SAM connectors. • Put the SAM in the slots. • Close the SAM connectors. • Replace and screw the back plate, the 2D Imager or the OCR reader (don’t forget to clean the OCR windows before). • Slide the switch to the position ON to turn power back on. • Replace the end-cap and battery. For detailed instructions, pleased refer to the WORKABOUT PRO 3 Hand-Held Computer User Manual. These manuals are available on our website www.psion.com through the Teknet extranet.
April 26, 2011 DPD 110052 A00 Sheet 4 of 6 MORPHOCHECK 2 RFID Regulatory Information
April 26, 2011 DPD 110052 A00 Sheet 5 of 6
April 26, 2011 DPD 110052 A00 Sheet 6 of 6 IMPORTANT NOTE FOR NORTH AMERICA: FCC Information to Users: This product and it antennas must not be co-located or operated in conjunction with any other antenna or transmitter. Radiation Exposure Compliance This product complies with the FCC RF exposure limits for an uncontrolled environment. For continued compliance, the product must not be held closer than 20 cm from the rest of the body. This product must not be used in a holster or on a belt-clip. Federal Communication Commission Interference Statement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Navigation menu