Corning Optical Communication MA1200AWS In-Building Distributed Antenna System User Manual USERS MANUAL

Corning Optical Communication Wireless In-Building Distributed Antenna System USERS MANUAL

Contents

USERS MANUAL

P/N 709C006503 REV:A00 DATE: APRIL 2014 Corning Optical Communications Corning CORE System MA2000 User Manual
Warranties P/N 709C006503 Page 2 Warranties Hardware Corning Optical Communications warrants to the original purchaser (“Customer”) that for the duration of the warranty period, one (1) year, commencing on the date of shipment of the Hardware, unless otherwise agreed in writing by Corning Optical Communications (the “Hardware Warranty Period”), the Hardware furnished by Corning Optical Communications shall be free in all material respects from defects in material and workmanship, and shall conform to the applicable portions of the Specifications, as defined below (the “Hardware Warranty”). If notified by Customer of any such defects in material or workmanship or nonconformity with applicable portions of the Specifications within the Hardware Warranty Period, Corning Optical Communications shall promptly, at its own election and expense, repair or replace any such Hardware proven to be defective under the terms of this Hardware Warranty. Such repair or replacement shall be Customer’s sole remedy and Corning Optical Communications’ sole obligation in the event this Hardware Warranty is invoked. If any components comprising a part of the Hardware are replaced or repaired during the Hardware Warranty Period, the Hardware Warranty Period for such repaired or replaced components shall extend to the longer of (i) the balance of the Hardware Warranty Period or (ii) three (3) months from the date of repair or replacement. For purposes of this Warranty, “Specifications” shall mean the specifications and performance standards of the Products as set forth in documents published by Corning Optical Communications s and delivered to Customer which contain technical specifications or performance standards for the Products. If Customer invokes this Hardware Warranty, it shall notify Corning Optical Communications promptly of the claimed defect. Customer will allow Corning Optical Communications to inspect the Hardware at Customer’s location, or to return the Hardware to Corning Optical Communications’ closest repair facility. For Hardware returned to Corning Optical Communications’ repair facility, Customer shall be responsible for payment of all transportation and freight costs (including insurance) to Corning Optical Communications’ repair facility, and Corning Optical Communications shall be responsible for all transportation and freight costs (including insurance) incurred in connection with the shipment of such Hardware to other repair facilities of Corning Optical Communications and/or its return to Customer. Notwithstanding the foregoing, in no event will Corning Optical Communications be liable for damage to Products resulting from improper handling during or after shipment, misuse, neglect, improper installation, operation or repair (other than by authorized Corning Optical Communications personnel), alteration, accident, or for any other cause not attributable to defects in materials or workmanship on the part of Corning Optical Communications. Corning Optical Communications shall not reimburse or make any allowance to Customer for any labor charges incurred by Customer for replacement or repair of any goods unless such charges are authorized in advance in writing by Corning Optical Communications. Software Warranty Corning Optical Communications warrants to the original purchaser (“Customer”) that for the duration of the warranty period, one (1) year, commencing on the date of shipment of the Software, unless otherwise agreed in writing by Corning Optical Communications (the “Software Warranty Period”), the Software shall conform with, and perform the functions set forth in the Specifications, and shall be free from defects in material or workmanship (the “Software Warranty”). In the event the Software is proven to be defective under the terms of this Software Warranty, Corning Optical Communications shall correct such defects or failure and ensure that the Software conforms with, and performs the functions set forth in, the Specifications. Customer will allow Corning Optical Communications to inspect the Software at Customer’s location or to return it to Corning Optical Communications’ closest repair facility. Notwithstanding the foregoing, Corning Optical Communications shall have no obligation under the Software Warranty if the Software is modified or used with hardware or software not supplied or approved by Corning Optical Communications or if the Software is subject to abuse, improper installation or application, accident, electrical or environmental over-stress, negligence in use, storage, transportation or handling. Third-party software distributed with the Software may carry certain warranties which, to the maximum extent allowed by law, Corning Optical Communications s hereby assigns, transfers and otherwise conveys to Customer, provided, however, that
Warranties P/N 709C006503 Page 3 Corning Optical Communications itself provides no warranty of any kind, express, implied, statutory or otherwise, for any third-party software provided hereunder. Corning Optical Communications does not warrant any hardware, software or services not provided by Corning Optical Communications. THIS WARRANTY IS THE ONLY WARRANTY MADE BY CORNING OPTICAL COMMUNICATIONS AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. CORNING OPTICAL COMMUNICATIONSS SHALL NOT BE LIABLE FOR ANY OTHER DAMAGE INCLUDING, BUT NOT LIMITED TO, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH FURNISHING OF GOODS, PARTS AND SERVICE HEREUNDER, OR THE PERFORMANCE, USE OF, OR INABILITY TO USE THE GOODS, PARTS AND SERVICE. CORNING OPTICAL COMMUNICATIONS SALES AGENTS OR REPRESENTATIVES ARE NOT AUTHORIZED TO MAKE COMMITMENTS ON WARRANTY RETURNS. Returns In the event that it is necessary to return any product against above warranty, the following procedure shall be followed: 1. Return authorization is to be received from Corning Optical Communications prior to returning any unit. Advise Corning Optical Communications of the model, Serial number, and discrepancy. The unit may then be forwarded to Corning Optical Communications, transportation prepaid. Devices returned collect or without authorization may not be accepted. 2. Prior to repair, Corning Optical Communications will advise the customer of our test results and any charges for repairing customer-caused problems or out-of-warranty conditions etc. 3. Repaired products are warranted for the balance of the original warranty period, or at least 90 days from date of shipment. Limitations of Liabilities Corning Optical Communications’ liability on any claim, of any kind, including negligence for any loss or damage arising from, connected with, or resulting from the purchase order, contract, quotation, or from the performance or breach thereof, or from the design, manufacture, sale, delivery, installation, inspection, operation or use of any equipment covered by or furnished under this contact, shall in no case exceed the purchase price of the device which gives rise to the claim. Except as expressly provided herein, Corning Optical Communications makes no warranty, expressed or implied, with respect to any goods, parts and services provided in connection with this agreement including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Corning Optical Communications shall not be liable for any other damage including, but not limited to, indirect, special or consequential damages arising out of or in connection with furnishing of goods, parts and service hereunder, or the performance, use of, or inability to use the goods, parts and service. Reporting Defects Note: Keep all packing material until you have completed the inspection. The units were inspected before shipment and found to be free of mechanical and electrical defects. Examine the units for any damage that may have been caused in transit. If damage is discovered, file a claim with the freight carrier immediately. Notify Corning Optical Communications as soon as possible in writing.
Warnings and Admonishments P/N 709C006503 Page 4 Warnings and Admonishments There may be situations, particularly for workplace environments near high-powered RF sources, where recommended limits for safe exposure of human beings to RF energy could be exceeded. In such cases, restrictive measures or actions may be necessary to ensure the safe use of RF energy. The equipment has been designed and constructed to prevent, as far as reasonably, practicable danger. Any work activity on or near equipment involving installation, operation or maintenance must be, as far as reasonably, free from danger. Where there is a risk of damage to electrical systems involving adverse weather, extreme temperatures, wet, corrosive or dirty conditions, flammable or explosive atmospheres, the system must be suitably installed to prevent danger. Equipment provided for the purpose of protecting individuals from electrical risk must be suitable for the purpose and properly maintained and used. This covers a range of activities including lifting, lowering, pushing, pulling, carrying, moving, holding or restraining an object, animal or person from the equipment. It also covers activities that require the use of force or effort, such as pulling a lever, or operating power tools. Where some of the abovementioned activities are required, the equipment must be handled with care to avoid being damaged. Observe standard precautions for handling ESD-sensitive devices. Assume that all solid-state electronic devices are ESD-sensitive. Ensure the use of a grounded wrist strap or equivalent while working with ESD-sensitive devices. Transport, store, and handle ESD-sensitive devices in static-safe environments. RF Safety WARNING! To comply with FCC RF exposure compliance requirements, each individual antenna used for this product must be fixed mounted in indoor permanent structures, providing a separation distance greater than 50 cm or more from all persons during normal operation and must not be co-located with any other antenna for meeting RF exposure requirements. The design of the antenna installation needs to be implemented in such a way so as to ensure RF radiation safety levels and non-environmental pollution during operation. WARNING! Antenna gain should not exceed 12.5 dBi. WARNING! The design of the antenna installation needs to be implemented in such a way so as to ensure RF radiation safety levels and non-environmental pollution during operation. Compliance with RF safety requirements: • Corning Optical Communications products have no inherent significant RF radiation. • The RF level on the downlink is very low at the downlink ports. Therefore, there is no dangerous RF radiation when the antenna is not connected. Power requirements for DC Inputs WARNING! Only use a special DC supply cable with four connectors WARNING! Always keep DC IN connectors connected during the product operation WARNING! Disconnect all power from the equipment by means of an external circuit breaker before connecting or disconnecting the DC IN connectors.
Laser Safety P/N 709C006503 Page 5 Laser Safety Fiber optic ports of the MA2K system elements emit invisible laser radiation at the 1310/1550 nm wavelength window. The laser apertures /outputs are the green SC/APC Bulkhead adapters located on the front panel of the equipment. The product is Class 1/Hazard level 1 External optical power is less than 10 mW, Internal optical power is less than 500 mW. To avoid eye injury never look directly into the optical ports, patchcords or optical cables. Do not stare into beam or view directly with optical instruments. Always assume that optical outputs are on. Only technicians familiar with fiber optic safety practices and procedures should perform optical fiber connections and disconnections of MA2K devices and the associated cables. Corning CORE System MA2000 has been tested and certified as a Class 1 Laser product to IEC/EN 60825-1 (2007). It also meets the requirements for a Hazard Level 1 laser product to IEC/EN 60825-2: 2004 to the same degree. Corning CORE System MA2000 system complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice NO. 50 (2007). Care of Fiber Optic Connectors Do not remove the protective covers on the fiber optic connectors until a connection is ready to be made. Do not leave connectors uncovered when not connected. The tip of the fiber optic connector should not come into contact with any object or dust. Refer to the cleaning procedure for information on the cleaning of the fiber tip. CAUTION! USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE Regulatory Compliance Information WARNINGS! • This is NOT a CONSUMER device. It is designed for installation by FCC LICENCEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. • ANTENNAS: Use only authorized and approved antennas, cables and/or coupling devices! The use of unapproved antennas, cables or coupling devices could cause damage and may be of violation of FCC regulations. The use of unapproved antennas, cables and/or coupling devices is illegal under FCC regulations and may subject the user to fines.
Standards and Certifications P/N 709C006503 Page 6 Standards and Certifications Corning Optical Communications products have met the approvals of the following certifying organizations: Company Certification ISO 9001: 2000 and ISO 13485: 2003 Product Certification US Radio Equipment and Systems • FCC 47 CFR part 22 – for CELL Frequency Band • FCC 47 CFR part 24 – for PCS Frequency Band • FCC 47 CFR part 27 – for LTE and AWS Frequency Bands • FCC CFR part 15 Subpart B • FCC CFR part 90 Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Warning! Changes or modifications to this equipment not expressly approved by Corning Mobile Access could void the user’s authority to operate the equipment. Europe Radio Equipment and Systems • EN 301502 – for GSM/EGSM Frequency Bands • EN 300609 – for DCS Frequency Bands • EN 301908 – for UMTS Frequency Band EMC EN 301 489 NTRL Safety UL 60950-1 Laser Safety IEC 60825-1, IEC 60825-2 TRA TRA type approval for UAE Licensee Contact Information Industrial Boosters may only be used by FCC licensees or those given express (individualized) consent of license. Corning Corning Optical Communications certifies all of the VARs listed as licensed installers for CMA. For the list of licensed VARs, please contact the CMA Tech Support Hotline: (US) 410-553-2086 or 800-787-1266.
About this User Manual P/N 709C006503 Page 7 About this User Manual This user guide describes how to perform the physical installation of the Corning CORE System MA2000. The installation procedures of other units (e.g. RIU, MA850/MA860, LTE) relevant to the system are detailed in their user manuals (see ‘Additional Relevant Documentation’ below). Additional Relevant Documents The following documents are required if the corresponding units are included in your system. Document Name MA850/MA860 Installation and Configuration Guide MobileAccess2000 700/800 Public Safety RHU Quick Start Guide MobileAccess1000 / MobileAccess2000 User Manual Addendum for 700 MHz LTE Solution RIU Installation and Configuration Guide SC-450 Installation and Configuration Guide NMS MA 410/430 Installation and Configuration Guide MA1000 MA2000 Commissioning Guide MA Software Version Update Tool List of Acronyms Acronym Description BDA Bi-Directional Amplifier BDAC Bi-Directional Amplifier Conditioner BTS Base Transceiver Station BTSC Base Transceiver Station Conditioner BU Base Unit DL Downlink LOS Line of Sight PS Power Supply RHU Remote Hub Unit RU Remote Unit RIU Radio Interface Unit SC-450 System Controller UL Uplink
Table of Contents P/N 709C006801 Page 8 Table of Contents Warranties ................................................................................................................................. 2 Hardware ....................................................................................................................................................... 2 Software Warranty ........................................................................................................................................ 2 Returns .......................................................................................................................................................... 3 Limitations of Liabilities ................................................................................................................................. 3 Reporting Defects ......................................................................................................................................... 3 Warnings and Admonishments................................................................................................ 4 RF Safety ................................................................................................................................... 4 Compliance with RF safety requirements: .................................................................................................... 4 Power requirements for DC Inputs .......................................................................................... 4 Laser Safety .............................................................................................................................. 5 Care of Fiber Optic Connectors .................................................................................................................... 5 Regulatory Compliance Information ........................................................................................ 5 Standards and Certifications ................................................................................................... 6 Company Certification ................................................................................................................................... 6 Product Certification ...................................................................................................................................... 6 Licensee Contact Information .................................................................................................. 6 About this User Manual ............................................................................................................ 7 Additional Relevant Documents .................................................................................................................... 7 List of Acronyms ....................................................................................................................... 7 Table of Contents ...................................................................................................................... 8 1 Introduction ...................................................................................................................... 11 1.1 Features and Capabilities ................................................................................................................... 11 1.2 MA2000 System Architecture .............................................................................................................. 12 1.2.1 Headend Equipment ................................................................................................................. 13 1.2.2 Remote-End Equipment ............................................................................................................ 13 1.3 Application Examples .......................................................................................................................... 14 1.4 System Monitoring and Management ................................................................................................. 16 2 MA2000 System Elements ............................................................................................... 17 2.1 Enclosure Types.................................................................................................................................. 17 2.1.1 MA2000 MRC............................................................................................................................ 17
Table of Contents P/N 709C006802 Page 9 2.1.2 MA2000 - Lite ............................................................................................................................ 20 2.2 MA2000 Remote Location Units ......................................................................................................... 21 2.2.1 MA2000 RU............................................................................................................................... 21 2.2.1.1 MA2000 RU Front Panel .............................................................................................. 22 2.2.1.2 MA2000 RU Rear Panel .............................................................................................. 23 2.2.2 MA1200 Add-on ........................................................................................................................ 23 2.2.2.1 MA1200 Front Panel .................................................................................................... 24 2.2.2.2 MA1200 Rear Panel .................................................................................................... 25 2.2.3 8 x 4 Combiner .......................................................................................................................... 26 2.2.3.1 MA 8x4 Combiner Front Panel .................................................................................... 26 2.2.3.2 MA 8x4 Rear Panel ...................................................................................................... 27 2.3 MA Base Unit ...................................................................................................................................... 27 2.3.1 Base Unit Models ...................................................................................................................... 27 2.3.2 BU Panels ................................................................................................................................. 28 2.3.2.1 MA BU Front Panel ...................................................................................................... 28 2.3.2.2 BU Rear Panel ............................................................................................................. 29 3 Installation Guidelines ..................................................................................................... 30 3.1 Site Considerations ............................................................................................................................. 30 3.2 Infrastructure Preparation ................................................................................................................... 30 3.3 Environmental ..................................................................................................................................... 30 3.4 Installation Requirements .................................................................................................................... 30 3.5 Coaxial Cable Connections ................................................................................................................. 31 3.5.1 General Cable Installation Procedures ..................................................................................... 31 3.5.2 Cable Routing ........................................................................................................................... 31 3.6 Fiber Optic Requirements ................................................................................................................... 31 3.6.1 Authorized Optic Cables ........................................................................................................... 31 3.6.2 Fiber Optic Rules ...................................................................................................................... 32 3.7 RF Rules ............................................................................................................................................. 32 3.8 Coax Cable Lengths and Losses ........................................................................................................ 33 3.9 Antenna Specifications and Guidelines .............................................................................................. 34 3.9.1 Authorized Antennas and Required Specifications................................................................... 34 3.9.2 General Antenna Installation Guidelines .................................................................................. 34 3.10 Grounding Requirement ...................................................................................................................... 34 3.11 Manual Handling ................................................................................................................................. 34 3.12 Power Consumption, Connections and Power Supplies .................................................................... 35 3.12.1 Power Safety Instructions ......................................................................................................... 35 3.12.2 Power Consumption of Units .................................................................................................... 35 3.12.3 Circuit Breakers ........................................................................................................................ 35 3.12.4 Types of Power Supplies .......................................................................................................... 35 3.13 Installation Conventions ...................................................................................................................... 36 4 System Installation .......................................................................................................... 37 4.1 Pre-installation Instructions ................................................................................................................. 37 4.1.1 Unpacking and Inspection ......................................................................................................... 37 4.2 Communication Room Installation ...................................................................................................... 37
Table of Contents P/N 709C006802 Page 10 4.2.1 Rack Installation General Instructions ...................................................................................... 37 4.2.2 MA2000 MRC Wall Mount Installation ...................................................................................... 41 4.2.3 MRC Grounding - Integrated PS Wall Mount Model ................................................................. 43 4.2.4 MRC 2000 Rack Mount Installation .......................................................................................... 44 4.2.5 Fiber Optic Connections ........................................................................................................... 45 4.2.6 Power Connections ................................................................................................................... 45 4.2.6.1 Integrated Power Supply model................................................................................... 45 4.2.7 Antenna Connections ................................................................................................................ 46 4.3 MA2000-Lite Installation and Connections ......................................................................................... 46 4.3.1 Mounting MA2000-Lite .............................................................................................................. 48 4.3.2 MA2000-Lite Connections ......................................................................................................... 49 5 Upgrading and Configuration Examples ........................................................................ 50 5.1 Common USA Configurations ............................................................................................................. 50 5.1.1 iDEN/SMR with PCS Add-on .................................................................................................... 50 5.1.2 Cell/PCSH ................................................................................................................................. 52 5.1.2.1 Cell/PCSH and LTE 700 .............................................................................................. 52 5.2 AWS Add-On ....................................................................................................................................... 53 5.3 Public Safety 700/800 ......................................................................................................................... 53 5.4 Typical International Configurations .................................................................................................... 54 5.4.1 Typical Asian Configuration: Cell/DCS+ UMTS ........................................................................ 54 5.4.2 Typical European & Middle East Configuration: EGSM/DCS + UMTS Configuration .............. 54 Appendix A : System Specifications ..................................................................................... 56 RF Parameters ............................................................................................................................................ 56 RF Frequency Range .......................................................................................................................... 56 Low Band ............................................................................................................................................ 57 High Band ............................................................................................................................................ 58 RF Parameters MA1200 Add-on ......................................................................................................... 59 System Specs ............................................................................................................................................. 60 Fiber Optic Specifications ................................................................................................................... 60 Absolute Maximum Rating .................................................................................................................. 60 Temperature Specifications ................................................................................................................ 60 Specifications of Units ................................................................................................................................. 61 MA 2000 MRC Remote Hub ............................................................................................................... 61 MA 2000 Lite ....................................................................................................................................... 61 MA 2000 Remote Unit ......................................................................................................................... 61 MA 1200 Add-On Specifications ......................................................................................................... 61 Base unit Specifications ...................................................................................................................... 62 Appendix B: Ordering Information ........................................................................................ 63
Introduction P/N 709C006503 Page 11 1 Introduction Corning CORE System MA2000 series provides enterprise level indoor coverage, of a wide range of multi-operator wireless services over a single broadband infrastructure. Front-end wireless RF services are routed, over optic fibers, to MA2000 series hubs that are securely located in the telecommunication closets at each remote location. These modular service aggregation platforms precisely combine multiple wireless service signals for simultaneous distribution over a common broadband infrastructure. Two remote service hub models are available: • MA2000-Lite – supports two remote units that are connected externally, where MA1200 Add-Ons and MA850/MA860 units can be integrated with the remote units. • MA2000 Cabinet (MRC) – internally houses a total of five remote units and MA1200 add-on units with which MA850/MA860 can be integrated as an external assembly. MA2000-Lite (left side) and MA2000 Cabinet (right side) Figure 1-1 1.1 Features and Capabilities • Multi-service platform that accommodates virtually any combination of wireless voice and data services eliminating the need for separate overlay networks • Scalable and future-safe – services can be added and removed without affecting existing operators or end-users • MA2000-Lite components can be migrated to MA2000 MRC for increased capacity • All active components are located in the communication closet/room • Carrier class operation – MA2000 advanced signal handling ensures optimal performance for all services within a multi-operator deployment • Local and remote end-to-end monitoring and control through interface to SC-450 controller • Conditioning and monitoring of input RF signals at the head-end through interface to MA-RIU Note: Corning Optical Communications has made the transition to ‘2000M’ products that support both single mode fiber and multimode fiber. The new Base Unit is designated by WBM (Wide Band M), and the new RUs (Remote Units) are indicated as ‘2000M’ RUs, where the suffix “M” indicates that the product will support both single mode and multimode fiber usage. The new products have the same packaging and performance and are fully backward compatible. See 3.6 for details on multimode fiber use.
Introduction P/N 709C006503 Page 12 1.2 MA2000 System Architecture The MA2000 solution comprises both headend and remote end equipment providing an end-to-end comprehensive system solution. Note: Third-party equipment is sold separately (i.e. cabling, antennas). At the head-end Corning CORE System elements provide interface to the wireless service provider’s network, where the signals can be conditioned through an active interface and transported over optic fiber to the remote end. At the remote end, the optical signal is reconverted to RF, amplified, filtered and distributed over the broadband antenna infrastructure. For end-to-end control, controllers installed at the head-end provide direct interface to the MA elements and through them, control over the remote end elements. MA2000 System Architecture Figure 1-2 Figure 1-2 shows a basic block diagram of the system operation. On the downlink, services from the BTS/BDA are transferred via interface to the Base Units (BUs). The interface, which may be passive (i.e. Interface Box) or active (RIU), is used to attenuate the RF signals to the required levels, converge them and distribute them to the BUs. The BUs are wideband – they are not service specific. At the BUs, the RF signals are converted to optical signals and transmitted over the optic fiber to (service-specific) RUs at the remote locations. At the remote locations, the RUs supported by the hub (MRC or Lite) reconvert the optical signal to RF. The hub elements converge the voice services together with 802.11 a/b/g data services (if MA850/MA860 units are installed) and distribute them over the coax antenna infrastructure. The MA SC-450 (in installations with remote management) provides monitoring and control of all active system elements.
Introduction P/N 709C006503 Page 13 1.2.1 Headend Equipment At the headend Corning CORE System elements provide interface to the wireless service provider’s network, where the signals can be conditioned through an active interface and transported over optic fiber to the remote end. • Radio Interface Unit (RIU): The RIU conditions the RF Downlink (DL) signals from an operator’s signal source (BTS: base-transceiver stations or BDA: bi-directional amplifiers) located inside the building. The RIU then custom tunes incoming signals in order to ensure a constant level of RF before signals are passed to/from the Base Unit (BU). RF Uplink (UL) signals from subscribers’ phones are received from the BU and transported back to the operator’s signal source (BTS or BDA) and to the operator’s macro network outdoors. • Base Unit (BU): The BU converts RF Downlink (DL) signals received from the RIU into an optical signal. This optical signal is then transported over single or multi-mode fiber optic cabling (SMF/MMF) to/from the MA2000 TSX units, which are housed inside of IDF/Telco/IT closets at the remote-end locations, for distribution throughout the facility. Uplink (UL) signals from subscribers’ phones are received from the antennas and sent back to the TSX units through the fiber connection to the head-end, where they are converted back from RF optical to RF electrical before being passed on to the RIU. • System Controller (SC-450): The system controller enables centralized remote management and control of all Corning CORE System MA2000 elements. 1.2.2 Remote-End Equipment The remote end elements interface to the DAS infrastructure. At the remote end, the optical signal is reconverted to RF, amplified, filtered and distributed over the broadband antenna infrastructure. • Remote Units (RUs) – Pre-configured service specific modules that support up to two voice services and perform the optic to RF conversion on signals received from the BU at the remote locations. Signals are automatically filtered and amplified for transport over broadband coax cable to a passive antenna. Uplink (UL) signals from the antennas are then converted to optical signals before being transmitted back to the BU. • MA1200 Add-On – Service specific module that provides support for an additional high band voice service. The AO is a single service module coupled with an RHU to deliver an additional, third service at a lower incremental cost. The AO receives RF signal from the RHU and amplifies it for transport across the broadband coax. • MA850/MA860 – Module that supports data services
Introduction P/N 709C006503 Page 14 1.3 Application Examples Figure 1-3 shows an example of an MA2000 Cabinet based solution. Five services from two different operators are distributed, where services from Operator A conflict with those from Operator B. The converted optical signal is routed from the BUs directly to the corresponding RUs in each Cabinet over optic fiber. Each BU supports connections to 8 RHUs. Additional BUs are required for connection to more RUs. Services 1 and 2 are distributed through one of the RHUs supported in each Cabinet. Services 3, 4 and 5 are distributed through the second RU and the MA1200 unit connected to that RU. MA850 and MA860 converge 802.11a/b/g data services with the voice services to be distributed through a common infrastructure of coax and wideband antennas. Example of MA2000 Cabinet Architecture Figure 1-3
Introduction P/N 709C006503 Page 15 Figure 1-4 shows an example of an MA2000-Lite based solution. Four services from two different operators are distributed. The converted optical signal is routed from the BUs directly to the corresponding RUs over optic fiber. Services 1 and 2 are distributed through one of the RUs supported by MA2000-Lite. Services 3 and 4 are distributed through the second RU. The combiner and filter provides interface to the antennas. Example of MA2000-Lite Architecture Figure 1-4
Introduction P/N 709C006503 Page 16 1.4 System Monitoring and Management The MA2000 system elements are centrally managed via the CORE SC-450 Controller. The elements are displayed in a hierarchal corresponding to their physical connections in the topology tree of the Management GUI. The following shows the Configuration tabs of the selected BU and RHU. Refer to the SC-450 Controller User Manual for information on how to configure and manage MA2000 elements. Example of MA2000 BU and RHU Configuration Tabs Figure 1-5
MA2000 System Elements P/N 709C006503 Page 17 2 MA2000 System Elements This chapter provides a full, detailed description of each of the system elements and their individual connections. The element descriptions are organized according to the following sections: • Enclosures types – MRC (MA2000 Remote Cabinet) and Lite • Remote Location Elements: • MA2000 Remote Units (RUs) • MA1200 Add-on • Base Unit Note: The following elements are fully described in their corresponding user guides: MA RIU, MA 850 /MA860, SC-450 Controller, MCT/NMS Management Application (described in MA410/MA430 Installation and Configuration Guide). 2.1 Enclosure Types This section describes both types of enclosures (MRC/Lite) and their external connections. 2.1.1 MA2000 MRC MA2000 MRC Closed Cabinet View Figure 2-1 MA2000 Cabinet supports the following functions: • Compactly houses up to five MA2000 RHU and MA1200 modules and the required filters Note: The number of modules that can be housed depends on the models, required filtering, etc. • MA850/MA860 can be connected externally • Converges all voice services and provides a single interface to the antennas through external connections • Wall mounted or rack mounted
MA2000 System Elements P/N 709C006503 Page 18 • Supplied in two models with differing power supply: • Integrated power supply – fed from an external AC power source. The MA2000 RHU an MA1200 Add-on modules are internally connected to the power supply. This model includes a battery connection as well. • External power supplies – power is routed to external connectors from which power is routed internally to each MA2000 RHU and MA1200 Add-On module Open door views Figure 2-2 shows an open MA2000 MRC cabinet, integrated power supply model, with four MA2000 RHU modules and four filters. (For clarity, the internal connections are demonstrated separately in Figure 2-3). MA2000 MRC Open Cabinet View (without Internal Connections) Figure 2-2
MA2000 System Elements P/N 709C006503 Page 19 Figure 2-3 shows the MA2000 MRC with the cabling. The antenna ports of the individual modules are connected to the relevant filters and to the 8 x 4 Combiner. The PS connections of each module are also connected to cables that are internally routed to the integrated PS (a full detailed description of the connections is provided in chapter 5). Note: The fiber optic connections are not displayed. MA2000 MRC Open Cabinet View (without Internal Connections) Figure 2-3
MA2000 System Elements P/N 709C006503 Page 20 2.1.2 MA2000 - Lite The MA2000-Lite is designed to support up to 8 voice services, in addition to 802.11 data services. MA2000-Lite System Figure 2-4 MA2000-Lite capabilities: • External connections to two MA2000 RHUs (to which MA1200 Add-on units can be added) • Internal filters and combiner (converges all services) • Connection to MA850/MA860 for support of 802.11a/b/g data services • External power supplies The MA2000 enclosure contains two sets of cables, each providing connections to two MA2000 RUs. Cable Connector Description Four N-type connectors Coax connections to corresponding antennas 1x DB-9 connector Connection to RU front panel RS232 connector The following table describes the MA2000-Lite front panel connectors. Connector Description Ant-1 to Ant-4 (N-type) Coax connections to corresponding antennas Control Control connector for MA service personnel. Power 20 to 48V DC power input The following table describes the front panel LEDs. LEDs Description Run Module is operating properly. Power Green – required power is supplied.
MA2000 System Elements P/N 709C006503 Page 21 2.2 MA2000 Remote Location Units Service specific units located at each remote location convert the optical signals received from the Base Units to RF signals and route them to the coax antenna infrastructure. Note: The voice services are converged by an 8x4 Combiner unit that is installed in the Cabinet enclosure and the Lite module. The following types of service specific elements are available: • Remote Units (RUs) – support two voice services • MA1200 Add-On – adds an additional (third) voice service to the host RU to which it is connected. • MA850/MA860 – converges data services from 802.11a/b/g APs and distributes them over the same coax and antenna infrastructure Note: The MA850/MA860 is described in detail in the MA850/MA860 Configuration and Installation guide. 2.2.1 MA2000 RU MA2000 RU is a service specific module that is either housed in the MA2000 Cabinet or connected externally to the MA2000-Lite module. It provides the following functions: • Performs the optic to RF (and vice versa) conversion at the remote locations • Supports two services – high-band and low-band • Interfaces to the optic fiber from the BU • Add-On ready – MA1200 can be added to support an additional services • Remote management - requires connection of host BU connection to an SC-450 controller Note: MA2000 also supports management via MA410/MA430 controllers.
MA2000 System Elements P/N 709C006503 Page 22 2.2.1.1 MA2000 RU Front Panel The MA2000 RU front panel contains the fiber optic connections to the BU, four coax connections to the antennas, power connections and status indicators. MA2000 RU Front Panel Figure 2-5 0 Front Panel Indicators LED Description COMM Active communication detected LINK Optical link to BU detected PWR DC power connection. 20 to 48VDC
MA2000 System Elements P/N 709C006503 Page 23 2.2.1.2 MA2000 RU Rear Panel The MA2000 RU rear panel provides the control, RF interface and optic interface ports that enable connecting to an MA1200 Add-On unit. MA2000 RHU Rear Panel Figure 2-6 Add-on control: Transmits the control signals from MA1200 Add-On module to the MA2000 RU module. The Add-on Control port is connected to the MA1200 Add-On From port. DL, UL: Transmit the RF signals to- and from- the MA1200 Add-On module. These ports are connected to the corresponding ports on the MA1200 rear panel: DL to DL, UL to UL. 2.2.2 MA1200 Add-on The MA1200 Add-On module is used to provide support for an additional service to an MA 2000 RU. The host MA2000 RU and the MA1200 Add-On are interconnected and either housed in a MA2000 Cabinet or connected externally to a MA2000-Lite ‘enclosure’. MA1200 Add-On provides the following functions: • Single service – either low-band or high-band • Installed only as an addition to a MA2000 RU Note: MA1200 Add-on does NOT interface directly to the fiber optic infrastructure, does not perform the optic to RF conversion and does not interface to the antennas. All these functions are provided by the host MA2000 RU unit.
MA2000 System Elements P/N 709C006503 Page 24 2.2.2.1 MA1200 Front Panel The MA1200 front panel contains the power connection and status LEDs. (The RS-232 connector is reserved for MA service personnel). The figure below shows the MA 1200 front view. It is followed by a description of the connections and LEDs. MA2000 1200 AO Front Panel Figure 2-7 Table 2-1. MA1200 Front Panel Connectors LED Description RS232 Servicing connector to be used by MA service personnel for maintenance. PWR DC Power connection. 25 to 48VDC Table 2-2. MA1200 Front Panel LEDsndicators LED Description RUN When blinking, indicates that the RU is in normal operating mode. PWR Power ON
MA2000 System Elements P/N 709C006503 Page 25 2.2.2.2 MA1200 Rear Panel The MA1200 rear panel contains the control connectors and the RF connections to the MA2000 RU and MA850/MA860. MA2000 1200 AO Rear Panel Figure 2-8 Table 2-3. MA1200 Rear Panel Connectors Add-on Control: Transmits the control signals between the MA1200 module and the MA850/MA860 and MA2000 RU modules. From – receives control signals from the MA2000 RU. Connected to the MA2000 RU Add-on Control connector. To – feeds control signals to MA850/MA860 (in configurations that include MA850/MA860) DL, UL: Transmit the RF signals to- and from- the MA1200 add-on module. These ports are connected to the corresponding ports on the MA 2000 rear panel: DL to DL, UL to UL. High: Service RF output port. Connected to combiner/splitter to be combined with other services supported by the MA2000 system.
MA2000 System Elements P/N 709C006503 Page 26 2.2.3 8 x 4 Combiner Note: This unit is internal to the MA2000 system – both Cabinet and Lite models. This unit is installed in the MA2000 system Cabinet and MA2000-Lite enclosures. It combines the RF outputs of the RUs in the corresponding system and provides a common interface to the coax antenna infrastructure. The 8x4 Combiner provides the following capabilities: • Supports up to eight RF voice service connections: four high-band and four low-band • Supports four antenna interface ports (located externally on the MA2000-Lite) • Provides low RF loss and high isolation for the input devices 2.2.3.1 MA 8x4 Combiner Front Panel The front panel of the unit contains the four antenna interface ports, LEDs and control port. 8 x 4 Combiner Front Panel Figure 2-9 Table 2-4 describes the front panel connectors. Table 2-4. 8 x 4 Front Panel Interfaces Connector Description Ant-1 to Ant-4 (N-type) Connections to corresponding antennas Setup Future Option Fiber Optic connection
MA2000 System Elements P/N 709C006503 Page 27 2.2.3.2 MA 8x4 Rear Panel The rear panel of the unit contains four low-band and four high-band ports as well as the control port. 8 x 4 Combiner Rear Panel Figure 2-10 Table 2-5 describes the 8 x 4 rear panel connectors. Table 2-5. 8 x 4 Combiner Rear Panel Connectors SMA Connectors Description Low Band Four connectors (ports 1-4) for the low-band outputs of the corresponding remote unit. Refer to Chapter 5 for the connections relevant to each configuration. High Band Four connectors (ports 5-8) for the high-band outputs of the corresponding remote unit. Refer to Chapter 5 for the connections relevant to each configuration. Control Interfaces to the Digital card (that enables antenna monitoring) 2.3 MA Base Unit The BU (Base Unit) is a wideband device that performs the conversion between the BTS/BDA (passive or active) interface RF signal and the remote units’ optic signal. Base Unit capabilities • Supports all services distributed by Corning CORE Systems • Fiber connection to up to 8 RUs • Setup and monitoring through connection to the host SC-450 controller and NMS software application • Dry contact alarms • Front panel indicators providing status on optical link internal circuitry and signal level 2.3.1 Base Unit Models Two models of MA BUs are available: • B4U - four port unit comprising one optical module supporting optic connections to up to four RHUs • B8U – eight port unit comprising two optical modules supporting optic connections to up to eight RHUs Note: Each optical module is separately accessed and managed in the MCT and NMS management applications.
MA2000 System Elements P/N 709C006503 Page 28 2.3.2 BU Panels 2.3.2.1 MA BU Front Panel The front panel contains the optical connections and indicators. Each four-port element has a dedicated set of indicators (PWR, LSR and Link 1 to Link 4 or Link 5 to Link 8). B4U and B8U Front Panels Figure 2-11 Table 2-6. MA BU Front Panel Indicators LED Description PWR Power input detected for the corresponding unit. 20 to 48VDC LSR ON - laser circuitry for the corresponding element (group of four ports) is functioning correctly. Link 1-4, 5-8 ON - the optical link to/from the connected remote functions within the specifications in both directions. Blinking - optical power from remote is lower than required
MA2000 System Elements P/N 709C006503 Page 29 2.3.2.2 BU Rear Panel The BU rear panel contains the RF connections, Alarms, NMS and power connections. Note: Figure 2-12 shows the rear panel of an 8-port BU. A 4-port BU contains a single UL and a single DL RF connector. B8U Rear Panel Figure 2-12 Table 2-7. MA BU Rear Panel Connections Connector Description Uplink output Uplink connectors to be connected on BTS/BDA side. For an 8-port BU, both UL connectors must be connected. Downlink input Downlink connectors to be connected on the BTS/BDA side. For an 8-port BU, both DL connectors must be connected. Com Port RS485 Connection to SC-450 controller, rear panel RS485 port. Alarms Dry-contact connections to BTS/BDA (normally closed). Relevant only for system without SC-450 controller. PWR Power connection: 20 to 48VDC
Installation Guidelines P/N 709C006503 Page 30 3 Installation Guidelines This following installation rules are based on the assumption that site survey and installation planning (including power requirements) have been completed. 3.1 Site Considerations • The distance between the service antenna and the coverage area should correspond to LOS requirements for maximum coverage area. • The maximum fiber path loss is 6 dB. • The system delay of the optical system must be taken into consideration when there are neighboring BTS sites overlapping in coverage. 3.2 Infrastructure Preparation The infrastructure preparation consists of two main phases: A. Floor Planning: Planning the distribution of the antennas on each floor to provide the required coverage. B. Telecom Closet Planning: Planning the layout of the devices and cables in the telecom closet or shaft. This includes the MA850/MA860, 802.11 Access Points, cabling and other voice service distribution systems that are relevant to the specific installation. 3.3 Environmental Humidity has an adverse effect on the reliability of the equipment. It is recommended to install the equipment in locations having stable temperature and unrestricted air-flow. The installation location for the system should be well ventilated. The equipment has been designed to operate at the temperature range and humidity level as stated in the product specifications with a relative humidity of max. 90% and temperatures ranging as follows: Operating: 0 to 50oC (-4° to 185°F) Storage: -20°C to 85°C (-4°F to 185°F) 3.4 Installation Requirements • Mounting surface shall be capable of supporting the weight of the equipment. • In order to avoid electromagnetic interference, a proper mounting location must be selected to minimize interference from electromagnetic sources such as large electrical equipment. • Working space available for installation and maintenance for each mounting arrangement. Ensure unrestricted airflow. • Ensure grounding connector is within reach of the ground wire. • Ensure a power source is within reach of the power cord and the power source has sufficient capacity. • Where appropriate, ensure unused RF connectors are terminated. • Do not locate the equipment near large transformers or motors that may cause electromagnetic interference. • Reduce signal loss in feeder cable by minimizing the length and number of RF connections. • Ensure the equipment will be operated within the stated environment (refer to datasheet). • Where appropriate, confirm available of suitably terminated grade of RF and optical fiber. • Observe handling of all cables to prevent damage.
Installation Guidelines P/N 709C006503 Page 31 3.5 Coaxial Cable Connections 3.5.1 General Cable Installation Procedures Note: The installer should be familiar with the ANSI/TIA/EIS-568 Cabling Standard guidelines. Observe the general cable installation procedures that meet with the building codes in your area. The building code requires that all cabling be installed above ceiling level (where applicable). The length of cable from the risers to each antenna must be concealed above the ceiling. The cable must be properly supported and maintained straight using velcro cable ties, cable trays and clamps or hangers every 10 feet (where practical above ceiling level). Where this is not practical, the following should be observed: • The minimum bending radius of the supplied ½” coax cable should be 7”. • Cable that is kinked or has a bending radius smaller than 7” must be replaced. • Cable runs that span less than two floors should be secured to suitably located mechanical structures. • The cables should be supported only from the building structure. • All cables shall be weather-resistant type. • Cable length - determined by the system installation plan. When calculating the cable length, take into account excess cable slack so as not to limit the insertion paths. 3.5.2 Cable Routing Ensure all cables, e.g. power cable, feeder cable, optic fiber, commissioning cable, connecting are properly routed and secured so that they are not damaged. 3.6 Fiber Optic Requirements 3.6.1 Authorized Optic Cables • Either single mode or multimode fiber can be used with Corning CORE 2000M products, while MA2000 products can only be used with single mode fiber. • Only Multimode fiber, 50/125 or 62.5/125um complying with ANSI/TIA/EIA-568-B series, EN50173-1 or ISO/IEC 11801 can be used. The fiber length can be up to 300 meters assuming the following qualifications: • All fiber in a given length of fiber must be of the same core diameter. • All Bulkhead adapters must be Single mode SC APC (Green) adapters. • All terminations, cross connections or patches must be direct fusion splice or Corning Optical Communications specified patch cords according to the listed below: 900 microns patchcord for splicing, 2 Meters, 2 x SC APC Diamond p/n ENC/1045341 Beige boots, 62.5/125/900 MA# 500001057 Diamond p/n ENC/1045340 Black boots, 50/125/900 MA# 500001058 Zipcord patchcord, 4 x SC APC, 50/125/900/2000/4500 micron Diamond p/n ENC/1045342 Black/Brown boots, 1Meter MA# 50000105 Diamond p/n ENC/1045343 Black/Brown boots, 3 Meter MA# 500001060 Zipcord patchcord, 4 x SC APC, 62.5/125/900/2000/4500 micron
Installation Guidelines P/N 709C006503 Page 32 Diamond p/n ENC/1045344 Beige/Brown boots, 1 Meter MA# 500001061 Diamond p/n ENC/1045345 Beige/Brown boots, 3 Meter MA# 500001062 3.6.2 Fiber Optic Rules ATTENTION! Please also refer to the Laser Safety section in the document Preface. • Use only 8-degree SC/APC connectors (green color). • Use only fusion splice for connecting two fibers. • Fiber optic cables require proper handling. Do not stretch, puncture, or crush the fiber cable(s) with staples, heavy equipment, doors, etc. • Always maintain the minimum bending radius specified by the cable manufacturer. The minimum bend radius is usually 10 times the cable's outer diameter. In the case of single optical fiber that is not in a cable, the minimum bending radius to be observed is 30 mm. • Pay special attention while connecting the SC APC connectors - ensure that you hear a “click”, indicating a secure connection • Use minimum splicing/connectors to achieve minimum losses on the fibers. • Use precaution while installing, bending, or connecting fiber optic cables. • Use an optical power meter and OTDR for checking the fiber optic cables. • Make sure the environment is clean while connecting/splicing fiber optic cables. • All fiber optic connectors should be cleaned prior to connecting to the system • Fiber connector protective caps should be installed on all non-terminated fibers and removed just before they are terminated. • Check the fiber optic connections. • Never look directly into the end of a fiber that may be carrying laser light. Laser light can be invisible and can damage your eyes. 3.7 RF Rules • Use coax RG223, 50ohm, male-to-male N-type for RF connections from the BUs to the BTS/RBS and to the RIU. • When using the Corning CORE System in an environment in which other indoor coverage systems are installed, it is recommended (where possible) that the antennas are placed at least two meters apart • When bending coax cables, verify that the bending radius does not exceed the coax specifications. • Use wideband antennas supporting a range of 800 MHz to 2500 MHz • Use a VSWR meter (i.e. Site Master or equivalent) for checking coax cables, including the antennas. (<2). The VSWR must be measured prior to terminating the RUs in the remote communication rooms • Terminate all unused RHU, AO and RIU ports with a 50 ohm load • Make sure that the VSWR measured at the coax cable meets the product specification. The VSWR must be measured prior to terminating the RHU RF ports in the remote communication rooms.
Installation Guidelines P/N 709C006503 Page 33 3.8 Coax Cable Lengths and Losses Use coax ½”, 50ohm, male-to-male N-type, for connecting to RHU and antenna ports. Note: The required distance between the antennas (installed in the ceiling) depends on the infrastructure and calculated path-loss. For example, if there is free space-loss between the antennas, a minimum distance of 100 ft is required; if there are partitions (loss) between the antennas, a distance of less than 100 ft between them is allowed. Table 3-1. Typical Coax Cable Lengths and Losses Coax Length Coax Loss (900 MHz) Connector Loss Total Loss 30 0.7 1.5 2.2 40 0.9 1.5 2.4 50 1.1 1.5 2.6 60 1.3 1.5 2.8 70 1.5 1.5 3 80 1.7 1.5 3.2 90 1.9 1.5 3.4 100 2.1 1.5 3.6 110 2.3 1.5 3.8 120 2.5 1.5 4 130 2.7 1.5 4.2 140 2.9 1.5 4.4 150 3.1 1.5 4.6 160 3.3 1.5 4.8 170 3.5 1.5 5 180 3.7 1.5 5.2 190 3.9 1.5 5.4 200 4.1 1.5 5.6
Installation Guidelines P/N 709C006503 Page 34 3.9 Antenna Specifications and Guidelines Determine the antenna installation configuration, according to the transmission and coverage requirements and the installation site conditions. 3.9.1 Authorized Antennas and Required Specifications External antennas - No limitation on any vendor of available external antennas with respect to the following requirements: • Omni Directional or Directional • Supported frequency range: wideband antennas supporting a range of 700 MHz to 2500 MHz • Gain: up to 12.5 dBi • Impedance: 50 Ohm • Types of couplers/splitters – depends on number of splits 3.9.2 General Antenna Installation Guidelines • The wideband antenna should be installed at a convenient location, free of metallic obstruction (can also be installed in plenum spaces). • Install the connected antenna at the designated height and tune it roughly toward the Service coverage area. • Each individual antenna used for this transmitter must be installed to provide the separation distance as specified in the FCC grant from all persons during normal operation and must not be co-located with any other antenna for meeting RF exposure requirements 3.10 Grounding Requirement Verify that the equipment has been well grounded (refer to the grounding lug located on the rear of the MRC cabinet). This includes antennas and all cables connected to the system. Ensure lightning protection for the antennas is properly grounded. 3.11 Manual Handling During transportation and installation, take necessary handling precautions to avoid potential physical injury to the installation personnel and the equipment.
Installation Guidelines P/N 709C006503 Page 35 3.12 Power Consumption, Connections and Power Supplies 3.12.1 Power Safety Instructions SAFETY WARNINGS • When installing or selecting the power supplies: • Be sure to disconnect all power sources before servicing. • Calculate the required power according to the requirements of the specific installation and then determine the configuration of the power supplies. The required DC cables will then be determined by the selected PS configuration. • Use only UL approved power supplies • AC and DC power supply cables – only use the power cords supplied with the units • Install external over-current protective devices for the system according to the requirements described in section 3.12.2. 3.12.2 Power Consumption of Units Table 3-2. Power Requirements Unit Type Voltage Input Typical Power Consumption Maximum Current Consumption MA2000 Remote Cabinet 20 to 48VDC 25W 1.25A MA2000-Lite 20 to 48VDC 3W 0.15A RU 2000 20 to 48VDC 25W 1.25A Add-on Unit 1200 25 to 48VDC 50W 2.0A RIU 20 to 48VDC 12W 0.6A Base Unit 20 to 48VDC 14W 0.7A MA410/MA430 Controller 20 to 48VDC 10W 0.5A SC-450 Controller 36 to 60 VDC 10W 0.2A MA850/MA860 20 to 48VDC 20W 1.0A 3.12.3 Circuit Breakers Install fuse protections for the system according to the following criteria: • The following system elements require external fuse protection: RIUs, BUs, and SC-450 Controllers. • Referring to Table 3-2, calculate the required fuse protection. • Example: a set of three elements consisting of a BU, RIU and SC-450 controller requires a 2A circuit breaker. 3.12.4 Types of Power Supplies Corning Optical Communications supplies various power supplies that can be installed in a rack or mounted on a wall, depending on your configuration.
Installation Guidelines P/N 709C006503 Page 36 3.13 Installation Conventions Some of the basic installation conventions are listed below for the MA 2000 system: • Base Units – are usually concentrated in the same location, most often in the main communication room. • Remote Cabinet/Lite – usually placed in the communication shaft or closet of a corresponding floor so they can be easily located. Each cabinet (or MA2000-Lite) can typically cover a floor of up to 30,000 sq ft. • Fiber optic cable - bundled fibers are terminated into the Base Units in the main communication room. The fibers are then routed to each coverage locations where individual fibers terminate into splice boxes. The splice box couples the installed fiber into the remote units. Enough spare fibers should be installed to take into account future expansion of the system. For example, for three remote units, six fibers are required. However, to allow for future expansion, it is recommended to install additional optic fibers to be connected to additional RHUs. The following figure illustrates fiber optic routing to Remote Cabinets. Illustration of Fiber Optic Routing Figure 3-1 • For remote power supply configuration - cable bundles are routed from the main communication room and individual wire pairs are terminated into the power feed of individual units. By providing power from a single distribution point, maintenance can be reduced and UPS backup can be easily provided. The maximum distance from the source to the termination spot is 1000 feet using 18 gauge wires. In many locations local codes do not require power to be run through conduit if 100 watts or less is used. Please consult the regulations in your local jurisdiction prior to deploying remote power. When power cables require distances greater than 1000 feet 14 or 16 gauge wire may be used. • On each floor - the antennas are connected to the Remote Cabinet or MA2000-Lite system using coax cables.
System Installation P/N 709C006503 Page 37 4 System Installation This chapter describes how the communication room and cabinet are installed. Note: Be sure to read the installation requirements (see Chapter 3) before proceeding with the actual connections. 4.1 Pre-installation Instructions In order to describe the installation process clearly, it will be described as consisting of two logical parts: A. Telecommunications room – installing the RIUs, BUs, SC-450 controller, and the required passive equipment in the telecommunication room close to the RF signal source. This installation may differ between single and multi-building topologies. B. Remote locations – two types of installations: • MRC Cabinet • MA2000-Lite The installations for two basic topologies are described in detail: for single building and for multi-building. By understanding the two generic installations you will be able to address any variations in system deployment. Note: For installations that include the NMS - once the installation has been completed, it can be verified using the MCT application (NMS User’s Guide) and the devices monitored using the NMS Manager (NMS User’s Guide). 4.1.1 Unpacking and Inspection This section provides instructions for opening the shipping boxes, verifying that all parts have been received, and verifying that no shipping damage has occurred. Unpack and inspect the cartons according to the following procedure 1. Open the shipping carton and carefully unpack each unit from the protective packing material. 2. Check for signs of external damage. If there is any damage, call your Corning Optical Communications service representative. 4.2 Communication Room Installation The Communication Room installation consists of the following basic steps: 1. Unpacking and inspecting the MA2000 units (see 4.1.1) 2. Mounting the RIUs, BUs and SC-450 controller in the mounting rack (see 4.2) 3 RF connections BTS/BDA connections. 4. RF connections to the Base Units. 5. Connecting the SC-450 control connections to the units 6. Connecting DC power to the units 4.2.1 Rack Installation General Instructions Note: Usually, each operator installs the equipment that supports their services in a separate rack.
System Installation P/N 709C006503 Page 38 It is recommended to install the following Corning CORE system modules in a 19” rack in the communication room • RIU Chassis 3U, RIU Lite 2U • BU 1U • MA410/MA430 controller 1U • Fiber Optic patch panel and splice tray • Power supply/supplies (Corning – 3U for each unit; units from other manufacturers may vary in size) Verify that the rack height can support all the units to be installed, where you may also want to consider future expansions. Figure 4-1 shows the recommended physical location of the Corning CORE elements in the rack in order to facilitate and simplify the cabling connections. The configuration is for a single operator. If the site is serviced by more than one operator, each operator often installs their equipment in a separate rack. Note: Note that the CORE 430/SC-450 controller is at eye level to provide an easy view of the LED indicators and LCD display and easy access to the local and remote monitoring connections. The following figure shows a typical installation for a two field design. Recommended Order in the Communication Room Rack Figure 4-1
System Installation P/N 709C006503 Page 39 Review the following guidelines to help ensure your safety and protect the equipment from damage during the installation. • Only trained and qualified personnel should be allowed to install or replace this equipment. • Verify that ambient temperature of the environment does not exceed 50°C (122°F) • To maintain a low center of gravity, ensure that heavier equipment is installed near the bottom of the rack and load the rack from the bottom to the top. • Ensure that adequate airflow and ventilation within the rack and around the installed components so that the safety of the equipment is not compromised. It is recommended to allow for at least about 2 cm of airspace between devices in the rack. • Verify that the equipment is grounded as required – especially the supply connections. BU Connections This section describes the installation for the Base Units with the RF signal supplied from an MA RIU Lite. If an RIU system is installed, refer to the RIU Installation and Configuration Guide for detailed instructions on the RIU connections. Note: It is assumed that the patch panel cabinet (SC APC adaptors) for fiber optic cable connections is installed in the rack near the BUs. To connect the BU 1. Connect fiber jumper between splice tray and patch panel cabinet. 2. Connect fiber jumpers between the corresponding BU optical ports and the patch panel. BU Front Panel Connections Figure 4-2 3. Connect the BU rear panel Uplink and Downlink ports to the corresponding ports on the RIU rear panel (or to the RF ports from the passive interface if your system does not include an RIU). 4. Connect the BU rear panel COM to the MA430 rear panel RS485 connector. 5. Connect the Power connection on the BU rear panel.
System Installation P/N 709C006503 Page 40 Figure 4-3 shows the BU connections to an MA RIU Lite and SC-450 controller. BU Rear Panel Connections Figure 4-3 Mount and install the Remote Cabinet (RC) in one of the following configurations: • Wallmount - on the wall in the communication room • Rack mount – in a 19” rack in the communication room allocated to that area (sometimes referred to as a secondary communication room). The procedure varies slightly according to the MA2000 Cabinet model: • Integrated power supply • External power supply The following sections describe both procedures. Note: For installations that include MA850/MA860 units, refer to the MA850/MA860 Installation and Configuration Guide for instructions on various installation options with the MA2000. General Installation Instructions The MA2000 Remote Cabinet units should be installed in a communication room that provides access to authorized personnel only. The units are maintenance free. In the event of failure, only authorized personnel should handle the units. • Environmental Data - Maximum ambient operating temperature: 45° C • Maximum ambient temperature in a rack: 45° C
System Installation P/N 709C006503 Page 41 4.2.2 MA2000 MRC Wall Mount Installation The following figures show the MA2000 Cabinet dimensions for a wall mount installation. MA2000 Cabinet Wall Mount Dimensions Figure 4-4
System Installation P/N 709C006503 Page 42 The wall installation MA2000 Remote Cabinet is supplied with a plate that is to be mounted on the wall and a bracket that is assembled on the rear of the MA2000 system. MA2000 System Wall Mount Figure 4-5 Mount the MA2000 MRC on the wall as follows: ATTENTION! The following instructions apply to an installation on a concrete wall. For any other type of wall, contact Corning Optical Communications. Note: For installations that include an MA850/MA860 system, refer to the CORE 850/860 Installation and Configuration Guide. 1. For integrated power supply configurations only (for other configuration grounding is optional), connect the cabinet GND according to section 4.2.3. 2. Using the plate as a guide, drill four holes for concrete anchors. Insert four concrete anchors (McMaster-Carr catalogue number 92403A200, or equivalent). 3. Mount the Plate on the wall. Carefully and thoroughly fasten the anchors to the wall. 4. Assemble the Bracket onto the rear of the Remote Cabinet using the supplied screws. 5. Lift the MA2000 MRC and guide the rear ledge of the assembled bracket onto the plate bracket. 6. Using the four screws, secure the RC Bracket to the Plate on the wall.
System Installation P/N 709C006503 Page 43 Note: Tighten the screws only as much as needed to secure the Bracket to the Plate. One should be able to loosen the screws quickly if needed. 4.2.3 MRC Grounding - Integrated PS Wall Mount Model Note: This procedure is only necessary for wall mount integrated power supply configuration (for other configurations this procedure is optional). The Ground screw is located at the rear of the unit. Grounding Located at the Rear of the Unit Figure 4-6
System Installation P/N 709C006503 Page 44 4.2.4 MRC 2000 Rack Mount Installation Note: The cabinet requires a clearance of 10 cm above the unit. If a heating source is installed beneath the MRC, a buffer must be placed between the cabinet and the surface. The following figure provides the dimensions for the MA2000 Rack Model. MA2000 Cabinet Rack Mount Assembly Figure 4-7 The MA2000 MRC Rack Mount model is supplied with the required brackets already assembled to the sides of the cabinet as indicated in Figure 4-7. Simply, mount the MA2000 MRC in the rack and secure with the supplied screws.
System Installation P/N 709C006503 Page 45 4.2.5 Fiber Optic Connections Note: Keep in mind the rules for handling and connecting F/O cables. The F/O cables will be connected to the associated BU in the communication room at a later phase. 1. Install splice box near Remote Cabinet. 2. Connect fiber optic cable to splice box and the SC APC pigtails to each RHU 2000 module. 3. For the downlink, connect the fiber optic cable pigtails from splice box coming from the BU port to the corresponding RU port (routing the optic fibers so they will fit through the top opening in the door.) 4. For the uplink, connect the fiber optic cable pigtails from splice box from the RU (routing the optic fibers so they will fit through the top opening in the door), to the uplink port that connects to the BU. 4.2.6 Power Connections Note: The internal power connections and other connections should already be connected. The power connections vary depending on whether the configuration is for an integrated PS or for external power supplies. 4.2.6.1 Integrated Power Supply model • Connect the AC power connector to the connector on the internal plate as illustrated below. The power source may be: 230 VAC, 115 VAC (an AC/DC converter is built into the chassis). • You may also connect a backup battery of 48V to the battery connector. This is an optional connection. Partial View of System Illustrating Location of Power Connections Figure 4-8
System Installation P/N 709C006503 Page 46 The external power source may be a central source with cables routed to each RU, or RU dedicated power supplies locally installed. • PS = 24 VDC to 48 VDC. • Connect each power connection to the appropriate connector on the remote cabinet. 4.2.7 Antenna Connections • For systems without MA850/MA860 modules - connect the antenna connections to the N-type RF antenna ports (1-4) on the side of the MRC cabinet • For systems with MA850/MA860 modules - refer to MA850/MA860 Installation Manual 4.3 MA2000-Lite Installation and Connections MA2000-Lite is designed as a wall-mount installation – usually located in the communication shaft of the corresponding floor. The remote units are mounted externally to the MA2000-Lite device and their antenna outputs are connected to either side of the MA2000-Lite device. The combined outputs are then connected to the antennas in the covered area. Figure 4-9 illustrates the MA2000-Lite coax connections to two RHUs. MA2000-Lite System Coax Connections Figure 4-9
System Installation P/N 709C006503 Page 47 Figure 4-9 shows the MA2000-Lite mechanical dimensions. MA2000 - Lite Mechanical Dimensions Figure 4-10
System Installation P/N 709C006503 Page 48 4.3.1 Mounting MA2000-Lite To mount the MA2000-Lite 1. Remove the top cover (to access the mounting holes) by pulling it towards the rear bracket and lifting it over the front brackets. The tray and all its assembled components are displayed. Note: The installed filters vary depending on the RHU models in the installation. MA2000-Lite Prepared for Mounting Figure 4-11 2. Depending on the tools you use: • Either measure the distance between the four wall mount holes and drill the required holes in the wall and insert the screws, or • Hold the tray up against the wall and simply drill the screws in the holes. 3. Mount each MA2000 RHU on the wall, on the corresponding side of the MA2000-Lite unit. 4. Re-assemble the MA2000-Lite cover by fitting it over the front tabs and pressing down gently at the rear.
System Installation P/N 709C006503 Page 49 4.3.2 MA2000-Lite Connections This section describes the MA2000-Lite enclosure and its' external connections. MA2000-Lite Connections Figure 4-12 Note: It is not required to perform the following procedures in any particular order. 1. Connect each of the side cable N-type antenna connectors to the antenna connectors of the corresponding RU(s). 2. Connect the DC power. 3. Connect each of the side cable D-type connector to the front panel RS232 connectors of the corresponding RU. 4. Connect the antenna cables to the front panel antenna connectors.
Upgrading and Configuration Examples P/N 709C006503 Page 50 5 Upgrading and Configuration Examples Corning CORE MA2000 provides an entry level cost effective solution for current services and support for future services from the same or different operators. Support for additional bands is implemented by an RU module and RU specific hardware designed to prevent interference with other existing bands in the coverage area. For support for additional services, connect the corresponding RU and hardware (Cavity Filter, Duplexer, etc.) to the 8x4 Module and to the external coax infrastructure. Note: It is required to order an Accessory Kit for each new unit to be added to the installation. The kit includes cables for connecting the MA2000 RU or MA1200 Add-On units to the required filters. Because of the differences in cable length requirements, the accessory kit differs for units designated to be installed in 2000 Cabinets and for those designated to be installed with MA2000-Lite systems. This chapter provides several examples of the most common configurations and their connections. As systems are expanded for additional services, refer to the provided diagrams for a description of the connections between the Remote Units (referred to as RHU 2000), the interface devices (Filters, etc.) and the 4x8 Combiner. 5.1 Common USA Configurations 5.1.1 iDEN/SMR with PCS Add-on iDEN and SMR coverage is implemented by one remote unit. This type of configuration was designed to meet Nextel’s existing needs. MA1200 add-on module for PCS support can be integrated into the solution at any time in order to meet future needs. Figure 5-1 describes the port connections between the remote units, add-on, and 8x4 Combiner. iDEN/SMR and PCS Connections Figure 5-1
Upgrading and Configuration Examples P/N 709C006503 Page 51 For infrastructures supporting a single Cell band and PCS, connect the RU according to Figure 5-2. Single Cell/PCS Connections Figure 5-2 For infrastructures supporting two Cell bands and a PCS band, connect the second Cell/PCS services RU according Figure 5-3.. Additional Cell/PCS Connections Figure 5-3 P1P4P3P2RHU 2000CELL/PCS Cavity Cell DuplexerN.C. 8x4 P18x4 P5CavityCell DLTxRxComP1P4P3P2RHU 2000CELL/PCS Cavity Cell DuplexerN.C. 8x4 P48x4 P8CavityCell DLTxRxCom
Upgrading and Configuration Examples P/N 709C006503 Page 52 5.1.2 Cell/PCSH Figure 5-4 provides a description of how to connect up to three Cell/PCSH services. Single Cell/PCSH Connections Figure 5-4 Note: In cases requiring more than one RHU, connect the additional units according to 2nd and 3rd RHU configuration. 5.1.2.1 Cell/PCSH and LTE 700 Figure 5-5 shows the connections for a configuration consisting of a 700 LTE Add-On unit with external filter and Cell/PCSH RHU. Single Cell/PCSH Connections Figure 5-5
Upgrading and Configuration Examples P/N 709C006503 Page 53 5.2 AWS Add-On Figure 5-6 shows the duplexer and 8x4 combiner connections for configurations with an AWS Add-On unit. AWS AO Connections Figure 5-6 5.3 Public Safety 700/800 Note: Both the MA2000 Public Safety 700/800 RHU and the corresponding filter unit are installed EXTERNALLY on the Cabinet. For information on the installing and configuring the MA2000 Public Safety 700/800 RHU refer to the MA2000 700/800 Public Safety RHU Quick Installation Sheet provided with the unit. The installation connections are as follows. 700/800 RHU Configuration Figure 5-7
Upgrading and Configuration Examples P/N 709C006503 Page 54 5.4 Typical International Configurations MA2000-Lite supports Cell/DCS and DCS. UMTS support can be added through MA1200 Add-On. 5.4.1 Typical Asian Configuration: Cell/DCS+ UMTS Cell/DCS and UMTS Configuration Figure 5-8 5.4.2 Typical European & Middle East Configuration: EGSM/DCS + UMTS Configuration Typical European & Middle East Configuration Figure 5-9
Upgrading and Configuration Examples P/N 709C006503 Page 55 iDEN support is provided through MA2000 Cabinet configurations. iDEN Configuration Figure 5-10 MA2000-Lite Cell/DCS and GSM/DCS Config for Telstra Figure 5-11 RHU 2000iDENP1P2P3P4CavityiDEN DL BPFto 8x4 P6to 8x4 P2
Appendix A : System Specifications P/N 709C006503 Page 56 Appendix A : System Specifications RF Parameters RF Frequency Range Frequency Range Services Uplink Downlink CELL 824-849 869-894 iDEN 806-824 851-869 GSM 890-915 935-960 E-GSM 880-915 925-960 Telstra 850M 824-849 869-890 SMR 896-902 929-941 DCS 1710-1785 1805-1880 PCS 1850-1910 1930-1990 G-PCS 1850-1915 1930-1995 UMTS 2100 1920-1980 2110-2170
Appendix A : System Specifications P/N 709C006503 Page 57 Low Band RF Parameters Low Band RU 2000 CELL TDMA/CDMA/WCDMA SMR 800 iDEN 800 Sprint GSM/ E-GSM SMR 900 IDEN 900 Sprint DL UL DL UL DL UL DL UL DL UL DL UL Max output PWR per antenna port 1 (comp) 16 14 10 12 14 10 2 carriers 13 11 7 9 11 7 4 carriers 10 8 4 6 8 4 8 carriers 7 5 1 3 5 1 12 carriers 5 3 -1 1 3 -1 Mean Gain(dB)* 16 7 14 7 10 7 12 7 14 7 10 7 Pin (dBm)* 0 0 0 0 0 0 Input IP3 (dBm) AGC OFF Min -5 -5 -5 -5 -5 -5 Input IP3 (dBm) AGC ON Min 5 5 5 5 5 5 SFDR** (dB) 71 72 72 64 71 71 Max Intermod Distortion (dBm) -13 -13 -13 -36 -13 -13 Max Nf (dB) 20 20 20 20 20 20 Gain Flatn. (dB) ± 2.0
Appendix A : System Specifications P/N 709C006503 Page 58 High Band RF Parameters High Band RU 2000 DCS PCS CDMA/WCDMA PCS GSM/TDMA DL UL DL UL DL UL Max output PWR per Antenna Port 1 (comp) 14 14 16 2 carriers 11 11 13 4 carriers 8 9 10 8 carriers 5 6 7 12 carriers 3 4 5 Mean Gain(dB)* 14 3 14 3 14 3 Pin (dBm)* 0 0 2 Input IP3 (dBm) AGC OFF Min -6 -6 -6 Input IP3 (dBm) AGC ON Min 3 3 3 SFDR** (dB) 64 66 64 Max Intermod Distortion (dBm) -30 -13 -13 Max Nf (dB) 20 20 20 Gain Flatn. (dB) ± 2.0 *Factory set mean gain BU-RHU without RIU. May be field adjusted using system controller. ** SFDR for CDMA services is calculated in 100Kb/sec
Appendix A : System Specifications P/N 709C006503 Page 59 RF Parameters MA1200 Add-on MA1200 Add-on G-PCS CDMA/WCDMA G-PCS GSM/TDMA UMTS*** DL UL DL UL DL UL Max output PWR per Antenna Port 1 (comp) 20 21 21 2 carriers 17 18 18 4 carriers 14 15 15 8 carriers 11 12 12 12 carriers 9 10 10 Mean Gain(dB)* 20 3 20 3 21 3 Pin (dBm)* 0 1 0 Input IP3 (dBm) AGC OFF Min -7 -7 -7 Input IP3 (dBm) AGC ON Min 3 3 SFDR** (dB) 66 64 66 70 Max Intermod Distortion (dBm) -13 -13 *** Max Nf (dB) 20 20 20 Gain Flatn. (dB) ± 2.0 *Factory set mean gain BU-RHU without RIU. May be field adjusted using system controller. ** SFDR for CDMA services is calculated in 100Kb/sec *** UMTS Compiles with 3GPP TS 25.106 V5.0.0 (2002-03) Table 9.4 spectrum emission mask
Appendix A : System Specifications P/N 709C006503 Page 60 System Specs Fiber Optic Specifications Optical output power <3.0mW Max. Optical budget 2 dB for fiber + 1 dB for connectors (assumed) = 3 dB total Optical loss per mated-pair connectors 0.5dB (max) Optical Connector SC/APC Fiber type 9/125 SM Wavelength 1310±10nm Maximum distance between Base Unit and Remote Cabinet 2Km Absolute Maximum Rating Total Input RF Power to BU 10dBm Total Input RF Power to RU 20dBm out-of-band -10dBm in-band Power Supply VDC 60VDC Temperature Specifications Operating 0°C to +50°C (32°F to 122°F) Storage -20°C to 85°C (-4°F to 185°F)
Appendix A : System Specifications P/N 709C006503 Page 61 Specifications of Units MA 2000 MRC Remote Hub Supported Units : A total of up to five Remote Units (one being a MA 1200 Add-on module) (not including MA 850/860 which is installed externally) RF antenna connections : Four N-type female antenna connections Input power Local powering : 230 VAC, 115 VAC (an AC/DC converter is built into the chassis). Remote powering : 20 to 48VDC to external connectors on chassis Power consumption : 25W Physical Mounting : Wallmount and rackmount Dimensions : 355 x 482.6 x 397mm (13.97” x 19” x 15.63” ) Weight (4 modules) : ~35Kg (~77 lb) MA 2000 Lite Supported Units : External connections to two Remote Units (MA 1200 Add-ons each unit) RF antenna connections : Four N-type female antenna connections Power consumption : 3W max (housing only with no remote units) Physical Mounting : Wallmount Dimensions : 442 x 336 x 86.41mm (17.4” x 13.23” x 3.4” ) Weight : 5.5Kg (12.1lb) MA 2000 Remote Unit Supported services : Two services corresponding to the model Power: Input power : 20 to 48V DC Power consumption : 29W RF connections : To Antenna (via hub) - N-type Female, 50 ohm : To MA 1200 add-on - SMA 50 ohm Optic connections : SC/APC optic connections Remote management : SNMP, NMS via Base Unit connection to SC-450 controller. MA 1200 Add-On Specifications Supported services : Single service corresponding to the model RF Connections: : To RHU - SMA 50 ohm Power: Input power : 25-48VDC Power consumption : 50W Remote management : SNMP, NMS via RHU connection Dimensions 27.9x22.0x6.9cm (10.98”x8.66”x2.71”) Weight 2.8Kg (6.2 lb)
Appendix A : System Specifications P/N 709C006503 Page 62 Base unit Specifications Models: 4-port model, 8-port model (shown above) Supported services: Wideband device supporting all services supported by MA systems RF (total Input): 10 dBm max Power: Input power 20 to 48V DC Power consumption 14W (8-port BU) RF connections N-type Female, 50 ohm – interface to RIU or to passive BTS interface N-type Female, 50 ohm – interface to antennas Optic connections Four or eight (depending on the model) SC/APC optic connections Remote management SNMP, NMS via connection to SC-450 controller. Physical Dimensions 48.26x4.44x29.97cm (19”x1Ux11.8”) Weight 2.82Kg (6.2lb)
Appendix B: Ordering Information P/N 709C006503 Page 63 Appendix B: Ordering Information Note: The information listed below is updated up to the document publishing date. Refer to the MA2000 datasheet for the most updated ordering information. Remote HUBs 2000-RC-RP 2000-RC-LP 2000-MINI-ENC Remote Cabinet - all services, Remote powering Remote Cabinet - all services, Local powering 2000 enclosure supporting 2 modules Dual Band RF Modules, add-on ready MA2000 Cabinet 2000-CELL-DCSE 2000-CELL-PCSE 2000-GSMO-DCSE 2000-IDEN-SMR 2000-E-GSM-DCS Dual band Cell/DCS 1 port for cabinet, enhanced power Dual band Cell/PCS 1 port for cabinet, enhanced power Dual band GSM DCS 1port for cabinet, enhanced power Dual band iDEN/SMR for cabinet Dual band EGSM/DCS 1 port for cabinet MA2000-Lite 2000-CELL-DCSEL 2000-CELL-PCSEL 2000-E-GSM-DCSL 2000-GSMO-DCSEL 2000-IDEN-SMR-L 2000-CELL-DCSLT 2000-GSM-DCSLT Dual band Cell/DCS 1 port for Lite, enhanced power Dual band Cell/PCS 1 port for Lite, enhanced power Dual band GSM/DCS 1 port for Lite, enhanced power Dual band GSM DCS 1 port for Lite, enhanced power Dual band iDEN/SMR for Lite Dual band Cell/DCS 1 port for Lite enhanced power for Telstra Dual band GSM/DCS 1 port for Lite enhanced power for Telstra MA1200 Add-On 1200-PCS-AO-CB 1200-G-PCS-AO-CB 1200-UMTSE-AO-CB 1200-PCS-AO-LT 1200-UMTSE-AO-LT Add-on RHU - PCS service for cabinet Add-on RHU supporting a PCS w/G-block for 2000 cabinet Add-on RHU - UMTS service for cabinet Add-on RHU - PCS service for Lite Add-on RHU - UMTS service for Lite Corning CORE System Universal Base Units WB-B8U WB-B4U Wide Band Base 8 Unit supporting 8 RHUs Wide Band Base 4 Unit supporting 4 RHUs Network Controller
P/N 709C006503 Page 64 SC-450 Network Controller –Ethernet/IP Interface 410 430 Network Controller – Serial Interface (dial-up) Network Controller –Ethernet/IP Interface Network Management System NMS-SW-SERVER NMS-SW-MFEE GUI and server S/W package (one per site) NMS annual S/W maintenance fee (per 430-CTLR) Corning CORE System Radio Interface Unit (RIU) RIU-IM RIU-BTSC-CELL RIU-BTSC-IDEN RIU-BTSC-PCS RIU-BTSC-G-PCS RIU-BTSC-SMR RIU-BTSC-GSM RIU-BTSC-E-GSM RIU-BTSC-DCS RIU-BTSC-UMTS RIU-BDAC-CELL RIU-BDAC-IDEN RIU-BDAC-PCS RIU-BDAC-G-PCS RIU-BDAC-SMR RIU-L-IDEN-SMR-G-PCS1 Radio Interface Unit BTS Conditioner for Cellular BTS Conditioner for iDEN BTS Conditioner for PCS BTS Conditioner for PCS w/ G-Block support BTS Conditioner for SMR-Paging BTS Conditioner for GSM 900MHz BTS Conditioner for EGSM 900MHz BTS Conditioner for DCS 1800MHz BTS Conditioner for UMTS 2100MHz BDA Conditioner for Cellular BDA Conditioner for iDEN BDA Conditioner for PCS BDA Conditioner for PCS w/ G-Block support BDA Conditioner for SMR-Paging RIU Lite for iDEN800,SMR 900,PCS1900 w/G-Block, support 1BU8 RIU-L-CELL-PCS1 RIU Lite Cellular 800,PCS 1900 Power Supply LPS-48V-66W Local AC/DC Converter 66W LPS-48V-100W AK-PWR-CORD-EU AK-PWR-CORD-UK Local AC/DC Converter 100W AC Power cord for 66W & 100W power supplies, European connector AC Power cord for 66W & 100W power supplies, UK connector Corning Optical Communications, Inc. 13221 Woodland Park Rd, Suite 400, Suite 400 • Herndon, VA 20171 USA 866-436-9266 • FAX: 703-848-0280 • Tech Support Hotline: 410-553-2086 or 800-787-1266 • www.corning.com/opcomm Corning Optical Communications reserves the right to improve, enhance and modify the features and specifications of Corning Optical Communications products without prior notification. All trademarks are the properties of their respective owners. Corning Optical Communications is ISO 9001 certified. © 2013 Corning Optical Communications. All rights reserved. Published in the USA. UM_ Corning CORE MA2000_709C006503_A00_30APRIL2014

Navigation menu