Corrisoft 5000CUFF iSECURETRAC Cuff User Manual FEDERAL COMMUNICATIONS COMMISSION

Download:
Mirror Download [FCC.gov]
Document ID	834738
Application ID	Jx9qxlgN2QY8eAUq5HehuA==
Document Description	manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	0.68kB (8439 bits)
Date Submitted	2007-08-28 00:00:00
Date Available	2007-08-28 00:00:00
Creation Date	2007-01-25 09:57:41
Producing Software	AFPL Ghostscript 8.14
Document Lastmod	2007-01-25 09:57:41
Document Title	FEDERAL COMMUNICATIONS COMMISSION
Document Creator	PDFCreator Version 0.8.0
Document Author:	John Bergman

User’s Manual
System 5000 Cuff
Overview
The System 5000 Cuff is used in conjunction with the System 5000 personal tracking unit (PTU) to track
individuals on probation a parole. It is placed on the ankle or wrist of the individual in a secure manner
so that any removal would be detected electronically.
Cuff Installation and Set-up
The cuff is installed by first affixing one side of the strap to cuff housing. This is accomplished by
aligning the keyed side of the strap with the receiving recess on the cuff housing and inserting and
locking fastener into place.
Once the fixed end of the strap is in place, make a loop by feeding the other end of the strap into the open
slot on the opposite side of the cuff housing. The open slot is in a lever that will be used in a later step to
properly size the strap. Place a fastening pin in the keyed recess of the lever; this will be used to secure
the lever once the strap has been properly fitted.
The cuff is started by placing the cuff housing in the activation point in the PTU charging base for 5
seconds.
The PTU will acknowledge the marriage of the cuff PTU on screen and the cuff will vibrate to also
acknowledge the marriage. Both should be observed for a positive start-up.
When marriage confirmation is received the cuff is placed on the individual’s ankle, by slipping the loop
over the foot and pulling the strap tight around the ankle so only two (2) fingers can place between the
strap and ankle.
Now close the lever slowly so the excess strap material is cut; remove the excess material by pulling
loose end away from the cuff housing and snap the lever closed. The retaining pin will snap into the base
of the cuff and the lever will remain closed.
Cuff Shutdown and Removal
To shut down the cuff a file must be sent for the website to the PTU. The PTU will then forward the
message to the cuff and the cuff will confirm shut-down by vibrating x time then stop transmitting.
At this point the cuff can be removed from the ankle and place set-up for use on the next individual.
FCC ID: OAM5000CUFF
FEDERAL COMMUNICATIONS COMMISSION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance could void the user‘s
authority to operate the equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiated radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Note:
This device and its antenna(s) used for this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Producer                        : AFPL Ghostscript 8.14
Create Date                     : 2007:01:25 09:57:41
Modify Date                     : 2007:01:25 09:57:41
Title                           : FEDERAL COMMUNICATIONS COMMISSION
Creator                         : PDFCreator Version 0.8.0
Author                          : John Bergman
Subject                         : 

EXIF Metadata provided by EXIF.tools