Cover Pools 50306 Wireless Numeric Control & Receiver User Manual User setup guide

Download:
Mirror Download [FCC.gov]
Document ID	575549
Application ID	sHoUraJy6krkPfQb476xJg==
Document Description	Exhibit 8
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.42kB (67723 bits)
Date Submitted	2005-08-26 00:00:00
Date Available	2005-08-26 00:00:00
Creation Date	2005-08-15 15:29:55
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2005-08-15 15:29:55
Document Title	Microsoft Word - User setup guide.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	mlj

Cover Pools Wireless Control System Setup
The Wireless Control System requires a setup process to link a keypad to the receiver
module. The following is a description of the sequence for setting up this link and
managing various features of the system.
Quick instructions for keypad use:
‘Factory default’ master PIN is 1583. The master PIN is #1, and can be changed.
Installer PIN is 2838. This PIN is also a master PIN, but is not changeable.
1. Normal use:
a. Enter 4 digit PIN #
i. Red LED on for button push ack.
ii. Red LED on for .5sec on PIN failure
iii. Green LED flash for good PIN recpt
b. Push Cover or Uncover buttons.
i. Green LED indicates ack from rcvr.
2. PIN change
a. Unlock keypad with valid master PIN entry (1a process)
b. Enter 1 to indicate change process
i. Both LED’s light indicating readiness
1. You can abort at this point by entering 0
c. Enter 1 for PIN change
i. Green LED flashes
d. Enter 1-4 for which PIN # desired
i. Red LED flashes
e. Enter the new PIN#
i. Both LED’s flash
f. Enter the new PIN# again (for confirmation)
i. Red LED flashes briefly
ii. After a moment the Green LED will turn on indicating success.
1. You can abort at this point by entering 0
3. Delete a specific PIN # (except master).
a. Unlock keypad with valid master PIN entry (1a process)
b. Enter 1 to indicate change process
i. Both LED’s light indicating readiness
1. You can abort at this point by entering 0
c. Enter 2 for PIN delete
i. Green LED flashes
d. Enter 2,3,4 for PIN to delete
i. Green LED flashes
e. Enter 2,3,4 for PIN to delete as a confirmation
i. After a brief delay, the Green LED will light showing success
1. You can abort at this point by entering 0
4. Delete all PIN#’s (except master)
a. Unlock keypad with valid master PIN entry (1a process)
b. Enter 1 to indicate change process
i. Both LED’s light indicating readiness
1. You can abort at this point by entering 0
c. Enter 3 for all PINs delete
i. Both LED’s flash
d. The master PIN must be entered again to verify the action
i. After a brief delay, the Green LED will light showing success
1. You can abort at this point by entering 0
Quick Installation instructions for the receiver module:
Quick functional description.
NOTE: The installation functions described must all be done at the same time for each
keypad in order for the receiver to store the setup properly. (ie radio linkage then set
channel then set net ID, then exit).
S3 on the PC board is the setup button.
Establish Setup mode
1. The Uncover and #3 button are pushed simultaneously and held for 5 secs.
a. Both LED’s light and stay on solid.
2. Enter the 6 digit master security code: 396207
a. The Red LED turns off. Only the Green is lit.
i. You can abort at this point by entering 4
Establish radio linkage
3. The ‘setup’ button on the receiver is pushed and held.
a. The receiver red LED lights
4. The #1 key is pressed on the keypad.
a. The LED’s turn off.
b. The Green LED turns on when link is established.
i. The Red LED will turn on if the link is not established
ii. Repeat step 3&4, or enter 4 to abort
Note: The receiver will timeout in about 20 seconds if no link is established.
Set Channel # (00 to 31)
(Still in setup)
5. Press #2 on the keypad
a. No LED’s lit
6. Enter channel (00 to 31). NOTE: ch 0-9 will need to be entered as 0x, etc.
a. Green LED is lit if successful. Red if not accepted.
Set Network ID #(01 – 99)
(Still in setup)
7. Press #3 on the keypad
a. No LED’s lit
8. Enter channel (00 to 99). NOTE: ch 0-9 will need to be entered as 0x, etc.
a. Green LED is lit if successful. Red if not accepted.
End setup
1. Press #0 on the keypad
a. No LED’s lit
b. Green LED is lit briefly if successful. Red if not accepted.
Initializing the Receiver
The receiver (which stores all the PINs and the base channel and network settings) can be
erased to a factory setup condition by holding the setup button down while the power to
the receiver is turned on. The Green LED will flash briefly indicating the erasure is
complete.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2005:08:15 15:29:55-06:00
Modify Date                     : 2005:08:15 15:29:55-05:00
Page Count                      : 4
Creation Date                   : 2005:08:15 21:29:55Z
Mod Date                        : 2005:08:15 21:29:55Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : mlj
Metadata Date                   : 2005:08:15 21:29:55Z
Creator                         : mlj
Title                           : Microsoft Word - User setup guide.doc
Page Mode                       : UseNone

EXIF Metadata provided by EXIF.tools