Cradlepoint MBR1200 Wireless-B/G/N Mobile Broadband Router User Manual Manual
Cradlepoint, Inc. Wireless-B/G/N Mobile Broadband Router Manual
Manual
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Following three 3.5G card have passed co-located EMC/RF exposure test with this device and could be used with this device.
Other 3.5G card may or may not comply with the FCC rule, please consult manufacture before purchase.
The EUT could be applied with one 3.5G 1XEV-DO Card and following four different models could be chosen; therefore emission
tests are added for simultaneously transmit between wireless LAN and 3.5G 1XEV-DO function. The emission tests have been
performed at the worst channel of both WLAN and 3.5G 1XEV-DO, and recorded in the report.
Interface Brand name Model name FCC ID
Cardbus KYOCERA KPC650 OVFKWC-KPC650
USB port SIERRA WIRELESS AirCard 875U N7N-MC8775U
USB port SIERRA WIRELESS AirCard 595U N7N-MC8725U
Express card Sprint AirCard 597E N7NAC597E
Industry Canada Statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two
conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired operation of the device
This device has been designed to operate with an antenna having a maximum gain of 4.98dBi.
Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna
impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP
is not more than required for successful communication.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
MOUNTING PROCEDURE
There are three ways for mounting the CEP:
Wall mounting
1. Locate a high position on the wall that is free of obstructions.
2. Connect two screws in the wall 5cm (2 in.) apart. Do not screw the screws all the way into the wall.
Important!
Make sure that the screws are securely fixed to the wall and strong enough to hold the weight of the CPE.