Cradlepoint S3A748A Integrated Mobile Broadband Router User Manual Regulatory Statements

Download:
Mirror Download [FCC.gov]
Document ID	3667964
Application ID	/RVBQGDaWnzg5mhQIK+N4A==
Document Description	User Manual Regulatory Statements
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.79kB (72349 bits)
Date Submitted	2017-12-08 00:00:00
Date Available	2018-01-31 00:00:00
Creation Date	2017-12-07 18:55:55
Producing Software	PDFCreator 2.3.0.103
Document Lastmod	2017-12-07 18:55:55
Document Title	IBR200 Safety Regulatory and Warranty guide Rev_1_1 - Part 170737-001
Document Creator	PDFCreator 2.3.0.103
Document Author:	kewei

SAFETY, REGULATORY, AND WARRANTY GUIDE
CRADLEPOINT
CRADLEPOINT
CRADLEPOINT
CRADLEPOINT
IBR200-10M-VZ
IBR250-10M-VZ
IBR200-10M-B-AT
IBR250-10M-B-AT
These devices have been designed to operate with WiFi antennas having a
maximum gain of 5 dBi. Antennas having a higher gain are strictly prohibited
per regulations of Industry Canada. The required antenna impedance is 50
ohms.
MODEL: S3A748A
MODEL: S3A753A
MODEL: S3A749A
MODEL: S3A754A
This important Safety, Regulatory, and Warranty Guide contains safety,
handling, disposal, regulatory, trademark, copyright, and software licensing
information.
Read all safety information below and operating instructions before using the
device to avoid injury.
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC STATEMENT
For product available in the USA/Canada market, only channel 1-11 can be
operated. Selection of other channels is not possible.
DÉCLARATION D’INDUSTRIE CANADA
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal
1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible.
NOTE IMPORTANTE (POUR L’UTILISATION DE DISPOSITIFS MOBILES):
DÉCLARATION D’EXPOSITION AUX RADIATIONS
Cet équipement est conforme aux limites d'exposition aux rayonnements IC
établies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec un minimum de 20 cm de distance entre la source de
rayonnement et votre corps.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement
en association avec une autre antenne ou transmetteur.
Le présent émetteur radio (IC: 6921A-S3A748A, 2417C-WP76A, 2417C-WP76C) a
été approuvé par Industrie Canada pour fonctionner avec les types d'antenne
énumérés ci-dessous et ayant un gain admissible maximal et l'impédance
requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette
liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement
interdits pour l'exploitation de l'émetteur.
Ce dispositive a ete concu pour fonctionner ave une antenna cellulaire ayant un
gain maximal de 3 dBi. Une antenne a gain plus eleve est strictement interdite
par les reglemnets d’Industrie Canada. L’impedance d’antenne requise est de
50 ohms.
Ce dispositive a ete concu pour fonctionner ave une antenna WiFi ayant un gain
maximal de 5 dBi. Une antenne a gain plus eleve est strictement interdite par
les reglemnets d’Industrie Canada. L’impedance d’antenne requise est de 50
ohms.
FCC RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance of 20 cm between the radiator and your body.
This device and its antennas(s) must not be co-located or operating in
conjunction with any other antenna or transmitter except in accordance with
FCC multi-transmitter product procedures.
To comply with FCC regulations limiting both maximum RF output power and
human exposure to RF radiation, the maximum cellular antenna gain must not
exceed 3.3 dBi.
To comply with FCC regulations limiting both maximum RF output power and
human exposure to RF radiation, the maximum WiFi antenna gain must not
exceed 5 dBi.
INDUSTRY CANADA STATEMENT
This device complies with ISED’s license-exempt RSS standards. Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
For product available in the USA/Canada market, only channel 1-11 can be
operated. Selection of other channels is not possible.
INDUSTRY CANADA RADIATION EXPOSURE STATEMENT
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance of 20 cm between the radiator and your body.
This device and its antennas(s) must not be co-located or operating in
conjunction with any other antenna or transmitter except in accordance with
IC multi-transmitter product procedures.
This radio transtter (IC: 6921A-S3A748A, 2417C-WP76A, 2417C-WP76C) has been
approved by Industry Canada to operate with the antenna types listed below
with the maximum permissible gain and required antenna impedance for each
antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
This device has been designed to operate with cellular antennas having a
maximum gain of 3 dBi. Antennas having a higher gain are strictly prohibited
per regulations of Industry Canada. The required antenna impedance is 50
ohms.
Revision 1.1
6 December 2017
Document Part: 170737-001
SAFETY AND HAZARDS
This equipment is designed to operate in ambient temperatures up to 60 °C
(140 °F). When operating in elevated ambient temperatures, the surface of the
equipment may exceed 70 °C and become too hot to safely touch. Under this
condition, this product must be installed in a secured location that is not
accessible to accidental touch, and access to the device must be restricted to
service persons or users who possess the proper tool or key to access the device
and have been informed about the potential high surface temperatures and
instructed on how to safely handle and/or service the device.
Under no circumstances should the device be used in any areas
(a) where blasting is in progress,
(b) where explosive atmospheres may be present, or
(c) that are near (i) medical or life support equipment, or (ii) any equipment
which may be susceptible to any form of radio interference.
In such areas, the device MUST BE POWERED OFF AT ALL TIMES (since the
device otherwise could transmit signals that might interfere with such
equipment).
In addition, under no circumstances should the device be used in any aircraft,
regardless of whether the aircraft is on the ground or in flight. In any aircraft,
the device MUST BE POWERED OFF AT ALL TIMES since the device otherwise
could transmit signals that might interfere with various onboard systems on
such aircraft. Furthermore, under no circumstances should the device be used
by the driver or operator of any vehicle. Such use of the device will detract
from the driver’s or operator’s control of that vehicle. In some jurisdictions,
use of the device while driving or operating a vehicle constitutes a civil and/or
criminal offense.
Due to the nature of wireless communications, transmission and reception of
data by the device can never be guaranteed, and it is possible that data
communicated or transmitted wirelessly may be delayed, corrupted (i.e.,
contain errors), or totally lost. The device is not intended for, and Cradlepoint
recommends the device not be used in any critical applications where failure to
transmit or receive data could result in property damage or loss or personal
injury of any kind (including death) to the user or to any other party.
Cradlepoint expressly disclaims liability for damages of any kind resulting from:
(a) delays, errors, or losses of any data transmitted or received using the
device; or
(b) any failure of the device to transmit or receive such data.
For proper and safe vehicle installations, the GPIO accessory cable must be
connected to a fused circuit in the vehicle. This fused circuit requires a 3A fuse.
If the supply connection is made directly to the battery, the fuse should be
installed in the positive lead. For North America, a UL Listed fuse is to be used.
Warning: This product is only to be installed by qualified personnel.
Purchaser agrees to indemnify Cradlepoint against any liability or damages
caused to third parties as a result of Purchaser’s misuse or misapplication of
the Cradlepoint product.
This product contains software distributed under one or more of the following
open source licenses: GNU General Public License Version 2, BSD License, NetSNMP License, and PSF License Agreement for Python 3.3. For more information
on this software, including licensing terms and your rights to access source
code, contact Cradlepoint at Cradlepoint.com/opensource.
WARRANTY INFORMATION
Cradlepoint, Inc. warrants this product against defects in materials and
workmanship to the original purchaser for a period of three (3) years from the
date of shipment. This warranty is limited to a repair or replacement of the
product, at Cradlepoint’s discretion, as purchaser’s sole and exclusive remedy.
Cradlepoint does not warrant that the operation of the device will meet your
requirements or be error free. CRADLEPOINT MAKES NO OTHER WARRANTY,
EITHER EXPRESSED OR IMPLIED, WITH RESPECT TO THIS PRODUCT.
CRADLEPOINT SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OR
CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
TITLE OR NON-INFRINGEMENT.
LIMITATION OF CRADLEPOINT LIABILITY
The information contained in this Safety, Regulatory, and Warranty Guide is
subject to change without notice and does not represent any commitment
on the part of Cradlepoint or its affiliates. CRADLEPOINT AND ITS AFFILIATES
HEREBY SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL: (A) DIRECT,
INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR
EXEMPLARY DAMAGES, INCLUDING WITHOUT LIMITATION FOR LOSS OF
PROFITS OR REVENUE OR OF ANTICIPATED PROFITS OR REVENUE ARISING
OUT OF THE USE OR INABILITY TO USE THE DEVICE, EVEN IF CRADLEPOINT
AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES, AND EVEN IF SUCH DAMAGES ARE FORESEEABLE; OR (B) CLAIMS
BY ANY THIRD PARTY. NOTWITHSTANDING THE FOREGOING, IN NO EVENT
SHALL THE AGGREGATE LIABILITY OF CRADLEPOINT AND/OR ITS AFFILIATES
ARISING UNDER OR IN CONNECTION WITH THE DEVICE, REGARDLESS OF THE
NUMBER OF EVENTS, OCCURRENCES, OR CLAIMS GIVING RISE TO LIABILITY,
EXCEED THE PRICE PAID BY THE ORIGINAL PURCHASER OF THE DEVICE.
PRIVACY
Cradlepoint may collect general data pertaining to the use of Cradlepoint
products via your Internet connection (wired and/or wireless) such as device
ID/serial number, network status, IP address, MAC address, operating system,
browser type and version number, etc., in order to provide you with better
services, enhance user experience, and improve performance.
OTHER BINDING DOCUMENTS; TRADEMARKS; COPYRIGHT
By activating or using your IBR200 device, you agree to be bound by
Cradlepoint’s Terms of Use, User License and other applicable Legal Policies.
© 2016 Cradlepoint, Inc. All rights reserved. Cradlepoint is not responsible for
omissions or errors in typography or photography. Cradlepoint, IBR200, and the
Cradlepoint logo are trademarks of Cradlepoint, Inc. in the US and other
countries. Other trademarks are property of their respective owners.
ROUTER COMMUNICATION/DATA USAGE
The factory default configuration of the router is set to communicate with
Cradlepoint and other resources at regular intervals to access the latest
firmware and modem updates, clock synchronization (NTP), and Enterprise
Cloud Manager (ECM) membership. Such communication may result in data
usage and applicable charges regardless of whether the router uses a wired or
wireless Internet connection. To avoid such data usage and potential charges,
consult the following Knowledge Base article:
http://knowledgebase.cradlepoint.com/articles/support/routercommunication-data-usage
OPEN SOURCE SOFTWARE
Revision 1.1
6 December 2017
Document Part: 170737-001

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2017:12:07 18:55:55+08:00
Modify Date                     : 2017:12:07 18:55:55+08:00
Author                          : kewei
Subject                         : 
Page Count                      : 2
Page Layout                     : SinglePage
Page Mode                       : UseNone
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:b2c2d9a9-dd98-11e7-0000-e46004c775f1
Producer                        : PDFCreator 2.3.0.103
Keywords                        : 
Creator Tool                    : PDFCreator 2.3.0.103
Document ID                     : uuid:b2c2d9a9-dd98-11e7-0000-e46004c775f1
Format                          : application/pdf
Title                           : IBR200 Safety Regulatory and Warranty guide Rev_1_1 - Part 170737-001
Creator                         : kewei
Description                     : 

EXIF Metadata provided by EXIF.tools