Craftsman 113177320 User Manual WET/DRY VAC Manuals And Guides L0107014
CRAFTSMAN Wet/Dry Vacuum Manual L0107014 CRAFTSMAN Wet/Dry Vacuum Owner's Manual, CRAFTSMAN Wet/Dry Vacuum installation guides
User Manual: Craftsman 113177320 113177320 CRAFTSMAN WET/DRY VAC - Manuals and Guides View the owners manual for your CRAFTSMAN WET/DRY VAC #113177320. Home:Vacuums & Floor Care Parts:Craftsman Parts:Craftsman WET/DRY VAC Manual
Open the PDF directly: View PDF 
.
Page Count: 8
Save This Manual
For Future Reference
S_EAIRS
owner's
manual
MODEL NO.
113.177320
16-GALLON
DOUBLE INSULATED
WET/DRY VAC
Serial
Number
Model and serial numbers
may be found on the
handle.
You should record both
model and serial number in
a safe place for future use.
FOR YOUR
SAFETY:
READ ALL
INSTRUCTIONS
CAREFULLY
SEARS / r.RRFT$IViRN
16-GALLON
FULLBLOWING
WET/DRYVAC
• assembly
•operating
•repair parts
J_ j
Sold by SEARS, ROEBUCK AND CO., Chicago, IL60684 U.S.A.
Part No, SP5500 Printed in U.S.A.
FULL ONE YEAR WARRANTY ON CRAFTSMAN WET/DRY VACS •
If within one year from the date of purchase, this Craftsman Wet/Dry Vac fails due to a defect in
material or workmanship, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERV-
ICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.
This warranty applies only while this product is used in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
SEARS, ROEBUCK AND CO., Dept. 698/731A, Sears Tower, Chicago, IL 60684 •
IMPORTANT SAFETY INSTRUCTIONS
When using your Wet/Dry Vac, follow basic safety precautions
including the following.
WARNING-Toreduce the risk of fire, elec-
tric shock, or injury:
Read and understand this owner's manual and all labels on
the Wet/Dry Vac before operating. Use only as described in
this manual. To avoid personal injury or damage to Wet/Dry
Vac, use only Sears Craftsman recommended accessories,
Sparks inside the motor can ignite flammable vapors or dust.
To avoid fire or explosion:
• Do not vacuum, or use this Wet!Dry Vac near, flammable or
combustible liquids, gases, or explosive dusts like gasoline
or other fuels, lighter fluid, cleaners, oil-based paints, natu-
ral gas, hydrogen, coal dust, magnesium dust, grain dust,
or gun powder.
• Do not use Wet/Dry Vac as a sprayer for any flammable or
combustible liquid.
Do not vacuum anything that is burning or smoking, such as
cigarettes, matches, or hot ashes.
To avoid health hazards from vapors or dusts, do not vacuum
toxic materials.
Do not use or store near hazardous materials.
To avoid electric shock, do not expose to rain. Store indoors.
Do not allow to be used as a toy. Close attention is necessary
when used by or near children.
Do not use this Wet/Dry Vac with a torn filter or without the fil-
ter installed except for vacuuming liquids as described in the
operations section of this manual.
Do not leave Wet!Dry Vac when plugged in. Unplug from out-
let when not in use and before servicing. Turn off Wet/Dry Vac
before unplugging.
To avoid injury from accidental starting, unplug power cord
before changing or cleaning filter.
Do not unplug by pulling on cord. To unplug, grasp the plug,
not the cord.
Do not use with damaged cord, plug or other parts. If your
Wet/Dry Vac is not working as it should, has missing parts,
has been dropped, damaged, left outdoors, or dropped into
water, return it to a Sears Service Center,
Do not pull or carry by cord, use cord as handle, close a door
on cord, or pull cord around sharp edges or corners. Do not
run Wet/Dry Vac over cord. Keep cord away from heated sur-
faces.
Do not handle plug or the Wet/Dry Vac with wet hands,
Do not put any object into ventilation openings. Do not vacu-
um with any ventilation openings blocked; keep free of dust,
lint, hair or anything that may reduce air flow.
Keep hair, loose clothing, fingers, and all parts of body away
from openings and moving parts.
To avoid falls, use extra care when cleaning on stairs.
This Wet/Dry Vac is double-insulated, eliminating the need for
a separate grounding system. Use only identical replacement
parts. Read the instructions for Servicing Double-Insulated
Wet/Dry Vacs before servicing.
Extension cords in poor condition or that are too small can
pose fire and shock hazards. When using an extension cord,
be sure it is in good condition. Using any extension cord will
cause some loss of power. To keep the loss to a minimum,
use the table below to choose the minimum wire size exten-
sion cord.
Extension Cord Length Wire Size
• 0-50 feet No. 14
• 50-100 feet No. 12
Observe the following warnings that appear on the motor
housing of your Wet/Dry Vac.
_[ DOUBLE iNSULATED. GROUNDING NOT
REQUIRED. WHEN SERVICING USE ONLY iDENTI-
CAL REPLACEMENT PARTS
WARNING: To avoid electric shock--do not expose to
rain--store indoors.
WARNING: For your own safety, read and understand
owner's manual. Do not pick up hot ashes, coals, toxic,
flammable or other hazardous materials. Do not use
around explosive liquids or vapors.
SAVE THESE INSTRUCTIONS
The operation of any utility vac can result in foreign objects
being blown into the eyes, which can result in severe eye
damage. Always wear safety goggles complying with ANSI
Z87.1 (shown on package) before commencing operation.
Safety Goggles are available at Sears retail or catalog stores.
WEAR YOUR
To avoid hearing damage, wear ear protectors when using the
vac for extended hours or when using it in a noisy area.
2
INTRODUCTION
This Wet/Dry Vac is intended for either commercial or house-
hold use.
IMPORTANT NOTE
Please Read Carefully
Static Shocks Are Common--In dry areas or when the rela
tive humidity of the air is low. To reduce the frequency of static
shocks in your home the best remedy is to add moisture to
the air with a console or installed humidifier.
OWNER'S MANUAL CONTENTS
Item Page
Warranty Information ............................................................ 2
Safety Instructions................................................................ 2
Introduction........................................................................... 3
Unpacking and Checking Carton Contents ......................... 3
Assembly .............................................................................. 3
Operation .............................................................................. 5
Maintenance ......................................................................... 6
Repair Parts.......................................................................... 7
Unpacking and Checking
uarton Contents
Remove entire contents of carton. Check each item against
the Carton Contents List. Notify your Sears Store immediately
if any parts are damaged or missing.
Carton Contents List
Key Description Qty.
A Vac Assembly ............................................................... 1
B Hose Assembly ............................................................. 1
C Rectangular Nozzle ...................................................... t
D Caster Foot .................................................................. 4
E Caster ........................................................................... 4
FOwners Manual ............................................................ !
G Filter Cage .................................................................... 1
H Filter .............................................................................. 1
I Float .............................................................................. f
JFilter Plate..................................................................... t
K Filter Nut ....................................................................... 1
A
B
float/cage assembly
WARNING: For your own safety, never connect plug to
power source outlet until all assembly steps are com-
plete and you have read and understood the safety and
operation instructions, Do not operate vac with any parts
damaged or missing.
1. Remove the top section of the vac from the drum and the
drum itself out of the carton. Place the top section of vac
upside down into the drum or place on a clean smooth
surface.
2. Locate the float. Place the float over the opening in the
center of the lid with the words "This Side Towards Lid"
laying face down over the hole.
WARNING: To avoid personal injury or damage to vac be
sure to keep hands, fingers, or any other foreign objects
out of the center opening when assembling the float.
3. Line up filter cage tabs to the slots in the center ring of the
lid assembly.
4. Push on the filter cage until the tabs snap into the slots for
a secure fit.
NOTE: If the filter cage needs to be removed, because the
float is placed in the wrong way, use a slotted screwdriver and
press the blade against one of the filter cage tabs. Push in on
the tab and lift the filter cage up. Tilt the filter cage slightly
away from the open slot to release the other two tabs. PuLlthe
filter cage away from the lid. To replace, follow float/cage
assembly instructions.
Filter
Cage
_Tabs
filter assembly
1. Carefully put the filter onto the filter cage by sliding it over
the center ring covering the 3 slots until it rests on the lid.
2. Place the hole of the filter plate over threaded screw of the
filter cage.
3. Gently push on the filter plate in order for the rubber ring of
the filter to seat inside the circular channel of the filter
plate.
4. Place fitter nut onto threaded screw and tighten it down.
Finger tighten only.
NOTE: Lever of filter nut should be away from plate as
shown.
CAUTION: Do not overtighten as this will deform or crack
the filter plate or filter cage. Filter nut lever should be
away from plate.
Filter
Nut
_p_. Filter
Plate
_Filter
,_._ Filter Cage
caster/caster foot assembly
1. Turn the dust drum upside down on the floor.
2. Insert the caster feet into the bottom of drum, as shown.
(4 ptaces)
3. Push on the caster foot until the foot is flush with bottom of
the dust drum.
4. Insert the caster stem into the socket of the caster foot, as
shown. (4 places)
5, Push on the caster until the ball on the caster stem is
inserted all the way into the socket. You will be able to
hear the ball snap into the socket and the caster will
swivel easily when positioning is correct.
6. Turn the drum upright.
NOTE: If your casters are noisy, you may put a drop of oil on
the roller shaft to make them quieter.
Caster
Caster Stem_
Caster Ball_
Caster _
Foot
vac assembly
1. Line up vacuum port in top assembly with drain cap locat-
ed on the front of the drum.
2. Place lid on top of drum with the handles snug against the
drum channel.
NOTE: Be sure lid completely covers the top of the drum so
leakage cannot occur.
3. Push down on top of the handles to cause the flexible lock-
ing tabs to hook onto the drum lip of the channel.
NOTE: Make sure that the locking tabs are snapped in place
to prevent the lid from coming off.
4. Insert the flexible plastic end of the hose, which is opposite
the swivel end, into the vacuum port directly above the
drain.
5. Place the rectangular nozzle securely on the swivel end of
the hose and the vac is ready for use.
NOTE: The swivel end of the hose is removable if more
hoses are needed to be attached for more length from the
vac. Hose accessory #9-17820.
Lid
Handle
\
TabOut
J
Channel
Drum
=lexible Locking Tabs
Do Not Force Flexible Tab
Beyond Stop Tab
Drain
Cap
Top Assembly
Push
Down
4
Pull
Out
Flexible
Locking
Tab
Swivel
End
4
6. Familiarize yourself with the controls and features of your
vac.
On-Off
Blowing Switch
Port /%=_---_--_f/ Power Cord
Cord Wrap %/ iL_" _f
,,rea Vacuum
_Port
Dust Drum---..-__ " j"_._ Hose
/uti,ity
Caster F.t _it_._ _ _'_r_ NOZZle
Cap
operation
WARNING
To avoid fire or explosion, do not operate this vac
in areas with flammable gases or flammable vapors
such as lighter fluid, cleaners, oil-base paints,
gasoline, alcohol or explosive dust such as coal,
magnesium, grain or gun powder in the air. Do not
vacuum explosive dust, flammable or combustible
liquids or hot ashes. Do not use this vac as a
sprayer for any flammable or combustible liquid. To
avoid health hazards from vapors or dusts, do not
vacuum toxic materials. To avoid electrical shock
do not expose to rain. Store vsc indoors. Unplug
power cord before changing or cleaning filter or
emptying the dust drum.
VACUUMING DRY MATERIALS
!. The filter must be in correct position at all times to avoid
leaks and possible damage to vac.
2. When using your vac to pick up very fine sawdust from
drywall type material it will be necessary for you to empty
the drum and clean the filter at more frequent intervals to
maintain peak vac performance,
NOTE: A dry filter is necessary to pick up dry material. If you
use your vac to pick up dust when the filter is wet, the filter will
clog quickly and be very difficult to clean.
3. If your filter is wet but you need to use the vac to pick up
dry material, you can quickly dry the filter by running the
vac without hose attached for 10 minutes. The clean air
rushing through the vac will dry the filter enough for dry
pick up.
EMPTYING DUST DRUM
1. To remove lid to empty contents of drum, simply pull flexi-
ble locking tabs on both sides of the drum to release from
the lip of the drum. It may be easier to do by pressing
down on the handles with the bottom part of the palm of
your hand while pulling outward on the flexible locking tabs
with your fingers,
2. While holding the tabs back, lift the top assembly up and
away from the drum
3. Lay top assembly upside down on a clean area while empty-
ing drum or changing filter.
VACUUMING LIQUIDS
1.
2,
3
4.
When the liquid in the drum reaches a predetermined
level, a float mechanism will rise automatically to cut off
airflow. When this happens, turn off the vac, unplug the
power cord, and empty the drum.
After using the vac to pick up liquids, the filter must be
dried to avoid possible mildew and damage to the filter.
When picking up small amounts of liquid the filter may be
left in place.
When picking up large amounts of liquid we recommend
that the filter be removed. If the filter is not removed, it will
become saturated and misting may appear in the blowing
port.
CAUTION: To avoid damage to the vac do not run motor
with float in raised position.
NOTE: You will know that the float has risen because vac air-
flow ceases and the motor noise will become higher in
pitch--due to increase in the motor speed.
Draining the Drum
WARNING: To avoid injury from accidental starting,
unplug power cord before emptying the drum.
1. The vac comes equipped with a drain for easy emptying of
liquids. Simply unscrew the drain cap and lift the opposite
side slightly to empty the drum.
2, Another option is to remove the top section of the vac, as
described in assembly section, and dispose of the con-
tents into a proper waste disposal container.
WARNING: To avoid back injury or falls, do not lift a vac
heavy with liquid or debris. Scoop enough contents out
to make the vac light enough to lift comfortably.
Cord Wrap
1. When vacuuming _scomplete, unplug the cord and wrap it
around the motor cover.
Moving the Vac
1. Should it become necessary to pick the vac up to move it,
DO NOT pick the vac up by the lid handles. To avoid drop-
ping the vac due to latches releasing or possible part
breakage, pick the vac up by the lip of the dust drum.
Theoperationofanyutilityvaccanresultinforeignobjects
beingblownintotheeyes, which can result in severe eye
damage. Always wear safety goggles complying with ANSI
Z87.1 (shown on Package) before commencing operation.
Safety Goggles are available at Sears retail or catalog stores.
WARNING: To avoid injury to bystanders, keep them
clear of blowing debris.
To avoid hearing damage, wear ear protectors when using the
vac for extended hours or when using it in a noisy area.
BLOWING FEATURE
Your vac features "Full Blowing". It has the capability to blow
sawdust and other debris. Follow the steps below to use your
vac as a blower.
!. Locate blowing port of your vac.
2. Insert soft end of your hose into blowing port.
3. Turn vac on and you are ready to use your vac as a
blower.
CAUTION: Always wear safety goggles complying with
ANSI Z87.1 before using as a blower.
NOTE: Sears recommended accessories are available at
Sears retail or catalog stores. The Sears Blower Nozzle Stock
No. 9-16933 and Extension Handles Stock No. 9-16964 are
recommended for blowing debris.
WEAR YOUR
End
Swivel End of Hose
filter maintenance
WARNING: To avoid injury from accidental starting,
unplug power cord before changing or cleaning tilter.
NOTICE: This filter is made of high quality paper designed to
stop very small particles of dust. The filter can be used for wet
or dry pick up. Handle the filter carefully when removing to
clean or installing it. Creases in the filter pleats may occur
from installation but creases will not affect the performance of
the filter.
Removal
To remove the old filter for cleaning or replacement:
1. Remove filter nut from the screw on the filter cage, remove
filter plate and lift off filter.
CAUTION: To avoid damage to the blower wheel, always
reinstall the filter before using the vac for dry material
pick-up.
Installation
(See page 4 "Filter Assembly")
WARNING: Do not remove the filter cage. It is there to
help prevent your fingers from getting into the blower
wheel.
Cleaning
Your filter should be cleaned often to maintain peak vac per-
formance.
NOTE: Be sure to dry the filter before storing or picking up dry
debris.
Dry Filter
1. Some removal of dry debris can be accomplished without
removing the filter from the vac by slapping your hand on
top of the lid while the vac is off.
2. After filter removal from vac, remove the dry debris by gen-
tly tapping the filter against the inside wall of your dust
drum and the debris will loosen and fall.
NOTE: For best results of cleaning due to accumulated dust,
clean the filter in an open area. Cleaning SHOULD be done
outdoors and not in the living quarters.
3. For thorough cleaning of dry filter with fine dust (no debris)
you may run water through it as described under "Wet
Filter".
Wet Filter
After filter is removed a wet filter should be cleaned by run-
ning water through it from a hose or spigot. Take care that
water pressure from the hose is not strong enough to damage
the filter.
IMPORTANT: You can quickly dry the filter by running the vac
without the hose assembly attached for approximately 16
minutes with filter in place to speed up drying. Check the filter
for tears or small holes. Even a small hole can cause a lot of
dust to come out of your vac. Do not use afilter with holes
or tears in it. Replace it immediately.
wet/dry vac maintenance
To keep your WetiDry Vac looking its best, clean the outside
with a cloth dampened with warm water and mild soap, to
clean the drum:
1. Dump debris out.
2. Wash drum thoroughly.
3. Wipe out with dry cloth.
IMPORTANT!-To assure product SAFETY and RELIABILITY,
repairs and adjustment should be performed by Sears
Service Centers, always using Sears replacement parts.
6
repair parts FOR 16 GALLON WET/DRY VAC 113.177320
Always order by Part Number- Not by Key Number
WARNING
SERVICING OF DOUBLE-INSULATED WET/DRY VAC
Ina double-insulated Wet/Dry Vac, two systems of insulation are provided instead of grounding. No grounding means is pro-
vided on a double-insulated appliance, nor should a means for grounding be added. Servicing a double-insulated Wet/Dry Vac
requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement
parts for a double-insulated Wet/Dry Vac must be identical to the parts they replace. Your double-insulated Wet/Dry Vac is
marked with the words "DOUBLE INSULATED" and the symbol _ (square within a square) may also be marked on the
appliances.
25,,,._ I _ _'_ \
3
Key Pad
No No.
1 9-17820
2 73324
3 9-16922
4 9-17816
5 73317
6 73316
7 809544
8 73185
9 73164
10 73102
11 73362
12 STD611007
13 73349
14 819450-2
15 73352
16 15534-1
17 818413-2
18 818961-2
19 819456
20 818792
21 818793
22 818805
23 73366
24 73180
25 STD611010
SP5500
Description
1Hose (Includes Key #2)
Hose Swivel
1 Utility Nozzle
1"Filter
Filter Plate
Filter Nut
Dust Drum
Drain Cap
Caster Foot
Caster
Filter Cage
* Screw-Pan Hd Type
"AB" No. 10 x 3/4
Float
Lid
Nut-Hex Flange 1/4-20
Washer
Blower Wheel
Spacer
Motor (Includes
Key No. 15, 16, 17 & 18)
Motor Gasket
Lid Gasket
Collector
Motor Cover
Toggle Switch
* Screw, Pan Hd Ty "AB"
No. 10x 1
Owners Manual
14
Jl
tStock Item - May Be Secured Through The
Hardware Department Of Most Sears
Retail Stores Or Catalog Order
Houses.
* Standard Hardware Item - May Be Purchased
Locally.
7
owner's
manual
SERVICE
MODEL NO.
113.177320
16-GALLON
DOUBLE INSULATED
WET/DRY VAC
HOW TO ORDER
REPAIRPARTS
f
16-GALLON
FULLBLOWING
WET/DRYVAC
Service is available by returning this Vac to the nearest Sears
Service Center/Department throughout the United States.
Model and serial numbers may be found on the handle.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING
INFORMATION:
PARTNUMBER
MODEL NUMBER
113.177320
PARTDESCRIPTION
NAME OF ITEM
Wet/Dry Vac
All parts listed may be ordered from any Sears Service Center
and most Sears stores. If the ports you need are not stocked
locally, your order will be electronically transmitted to a Sears
Repair Parts Distribution Center for handling.
Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A.
Part No, SP5500 Form No. SP5500 Printed in U,S.A. 3/91
